linux/drivers/pcmcia/xxs1500_ss.c
<<
>>
Prefs
   1/*
   2 * PCMCIA socket code for the MyCable XXS1500 system.
   3 *
   4 * Copyright (c) 2009 Manuel Lauss <manuel.lauss@gmail.com>
   5 *
   6 */
   7
   8#include <linux/delay.h>
   9#include <linux/gpio.h>
  10#include <linux/interrupt.h>
  11#include <linux/io.h>
  12#include <linux/ioport.h>
  13#include <linux/mm.h>
  14#include <linux/platform_device.h>
  15#include <linux/pm.h>
  16#include <linux/resource.h>
  17#include <linux/slab.h>
  18#include <linux/spinlock.h>
  19
  20#include <pcmcia/ss.h>
  21#include <pcmcia/cistpl.h>
  22
  23#include <asm/irq.h>
  24#include <asm/mach-au1x00/au1000.h>
  25
  26#define MEM_MAP_SIZE    0x400000
  27#define IO_MAP_SIZE     0x1000
  28
  29
  30/*
  31 * 3.3V cards only; all interfacing is done via gpios:
  32 *
  33 * 0/1:  carddetect (00 = card present, xx = huh)
  34 * 4:    card irq
  35 * 204:  reset (high-act)
  36 * 205:  buffer enable (low-act)
  37 * 208/209: card voltage key (00,01,10,11)
  38 * 210:  battwarn
  39 * 211:  batdead
  40 * 214:  power (low-act)
  41 */
  42#define GPIO_CDA        0
  43#define GPIO_CDB        1
  44#define GPIO_CARDIRQ    4
  45#define GPIO_RESET      204
  46#define GPIO_OUTEN      205
  47#define GPIO_VSL        208
  48#define GPIO_VSH        209
  49#define GPIO_BATTDEAD   210
  50#define GPIO_BATTWARN   211
  51#define GPIO_POWER      214
  52
  53struct xxs1500_pcmcia_sock {
  54        struct pcmcia_socket    socket;
  55        void            *virt_io;
  56
  57        phys_addr_t     phys_io;
  58        phys_addr_t     phys_attr;
  59        phys_addr_t     phys_mem;
  60
  61        /* previous flags for set_socket() */
  62        unsigned int old_flags;
  63};
  64
  65#define to_xxs_socket(x) container_of(x, struct xxs1500_pcmcia_sock, socket)
  66
  67static irqreturn_t cdirq(int irq, void *data)
  68{
  69        struct xxs1500_pcmcia_sock *sock = data;
  70
  71        pcmcia_parse_events(&sock->socket, SS_DETECT);
  72
  73        return IRQ_HANDLED;
  74}
  75
  76static int xxs1500_pcmcia_configure(struct pcmcia_socket *skt,
  77                                    struct socket_state_t *state)
  78{
  79        struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
  80        unsigned int changed;
  81
  82        /* power control */
  83        switch (state->Vcc) {
  84        case 0:
  85                gpio_set_value(GPIO_POWER, 1);  /* power off */
  86                break;
  87        case 33:
  88                gpio_set_value(GPIO_POWER, 0);  /* power on */
  89                break;
  90        case 50:
  91        default:
  92                return -EINVAL;
  93        }
  94
  95        changed = state->flags ^ sock->old_flags;
  96
  97        if (changed & SS_RESET) {
  98                if (state->flags & SS_RESET) {
  99                        gpio_set_value(GPIO_RESET, 1);  /* assert reset */
 100                        gpio_set_value(GPIO_OUTEN, 1);  /* buffers off */
 101                } else {
 102                        gpio_set_value(GPIO_RESET, 0);  /* deassert reset */
 103                        gpio_set_value(GPIO_OUTEN, 0);  /* buffers on */
 104                        msleep(500);
 105                }
 106        }
 107
 108        sock->old_flags = state->flags;
 109
 110        return 0;
 111}
 112
 113static int xxs1500_pcmcia_get_status(struct pcmcia_socket *skt,
 114                                     unsigned int *value)
 115{
 116        unsigned int status;
 117        int i;
 118
 119        status = 0;
 120
 121        /* check carddetects: GPIO[0:1] must both be low */
 122        if (!gpio_get_value(GPIO_CDA) && !gpio_get_value(GPIO_CDB))
 123                status |= SS_DETECT;
 124
 125        /* determine card voltage: GPIO[208:209] binary value */
 126        i = (!!gpio_get_value(GPIO_VSL)) | ((!!gpio_get_value(GPIO_VSH)) << 1);
 127
 128        switch (i) {
 129        case 0:
 130        case 1:
 131        case 2:
 132                status |= SS_3VCARD;    /* 3V card */
 133                break;
 134        case 3:                         /* 5V card, unsupported */
 135        default:
 136                status |= SS_XVCARD;    /* treated as unsupported in core */
 137        }
 138
 139        /* GPIO214: low active power switch */
 140        status |= gpio_get_value(GPIO_POWER) ? 0 : SS_POWERON;
 141
 142        /* GPIO204: high-active reset line */
 143        status |= gpio_get_value(GPIO_RESET) ? SS_RESET : SS_READY;
 144
 145        /* other stuff */
 146        status |= gpio_get_value(GPIO_BATTDEAD) ? 0 : SS_BATDEAD;
 147        status |= gpio_get_value(GPIO_BATTWARN) ? 0 : SS_BATWARN;
 148
 149        *value = status;
 150
 151        return 0;
 152}
 153
 154static int xxs1500_pcmcia_sock_init(struct pcmcia_socket *skt)
 155{
 156        gpio_direction_input(GPIO_CDA);
 157        gpio_direction_input(GPIO_CDB);
 158        gpio_direction_input(GPIO_VSL);
 159        gpio_direction_input(GPIO_VSH);
 160        gpio_direction_input(GPIO_BATTDEAD);
 161        gpio_direction_input(GPIO_BATTWARN);
 162        gpio_direction_output(GPIO_RESET, 1);   /* assert reset */
 163        gpio_direction_output(GPIO_OUTEN, 1);   /* disable buffers */
 164        gpio_direction_output(GPIO_POWER, 1);   /* power off */
 165
 166        return 0;
 167}
 168
 169static int xxs1500_pcmcia_sock_suspend(struct pcmcia_socket *skt)
 170{
 171        return 0;
 172}
 173
 174static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
 175                                    struct pccard_io_map *map)
 176{
 177        struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
 178
 179        map->start = (u32)sock->virt_io;
 180        map->stop = map->start + IO_MAP_SIZE;
 181
 182        return 0;
 183}
 184
 185static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
 186                                     struct pccard_mem_map *map)
 187{
 188        struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
 189
 190        if (map->flags & MAP_ATTRIB)
 191                map->static_start = sock->phys_attr + map->card_start;
 192        else
 193                map->static_start = sock->phys_mem + map->card_start;
 194
 195        return 0;
 196}
 197
 198static struct pccard_operations xxs1500_pcmcia_operations = {
 199        .init                   = xxs1500_pcmcia_sock_init,
 200        .suspend                = xxs1500_pcmcia_sock_suspend,
 201        .get_status             = xxs1500_pcmcia_get_status,
 202        .set_socket             = xxs1500_pcmcia_configure,
 203        .set_io_map             = au1x00_pcmcia_set_io_map,
 204        .set_mem_map            = au1x00_pcmcia_set_mem_map,
 205};
 206
 207static int xxs1500_pcmcia_probe(struct platform_device *pdev)
 208{
 209        struct xxs1500_pcmcia_sock *sock;
 210        struct resource *r;
 211        int ret, irq;
 212
 213        sock = kzalloc(sizeof(struct xxs1500_pcmcia_sock), GFP_KERNEL);
 214        if (!sock)
 215                return -ENOMEM;
 216
 217        ret = -ENODEV;
 218
 219        /* 36bit PCMCIA Attribute area address */
 220        r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-attr");
 221        if (!r) {
 222                dev_err(&pdev->dev, "missing 'pcmcia-attr' resource!\n");
 223                goto out0;
 224        }
 225        sock->phys_attr = r->start;
 226
 227        /* 36bit PCMCIA Memory area address */
 228        r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-mem");
 229        if (!r) {
 230                dev_err(&pdev->dev, "missing 'pcmcia-mem' resource!\n");
 231                goto out0;
 232        }
 233        sock->phys_mem = r->start;
 234
 235        /* 36bit PCMCIA IO area address */
 236        r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-io");
 237        if (!r) {
 238                dev_err(&pdev->dev, "missing 'pcmcia-io' resource!\n");
 239                goto out0;
 240        }
 241        sock->phys_io = r->start;
 242
 243
 244        /*
 245         * PCMCIA client drivers use the inb/outb macros to access
 246         * the IO registers.  Since mips_io_port_base is added
 247         * to the access address of the mips implementation of
 248         * inb/outb, we need to subtract it here because we want
 249         * to access the I/O or MEM address directly, without
 250         * going through this "mips_io_port_base" mechanism.
 251         */
 252        sock->virt_io = (void *)(ioremap(sock->phys_io, IO_MAP_SIZE) -
 253                                 mips_io_port_base);
 254
 255        if (!sock->virt_io) {
 256                dev_err(&pdev->dev, "cannot remap IO area\n");
 257                ret = -ENOMEM;
 258                goto out0;
 259        }
 260
 261        sock->socket.ops        = &xxs1500_pcmcia_operations;
 262        sock->socket.owner      = THIS_MODULE;
 263        sock->socket.pci_irq    = gpio_to_irq(GPIO_CARDIRQ);
 264        sock->socket.features   = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
 265        sock->socket.map_size   = MEM_MAP_SIZE;
 266        sock->socket.io_offset  = (unsigned long)sock->virt_io;
 267        sock->socket.dev.parent = &pdev->dev;
 268        sock->socket.resource_ops = &pccard_static_ops;
 269
 270        platform_set_drvdata(pdev, sock);
 271
 272        /* setup carddetect irq: use one of the 2 GPIOs as an
 273         * edge detector.
 274         */
 275        irq = gpio_to_irq(GPIO_CDA);
 276        irq_set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
 277        ret = request_irq(irq, cdirq, 0, "pcmcia_carddetect", sock);
 278        if (ret) {
 279                dev_err(&pdev->dev, "cannot setup cd irq\n");
 280                goto out1;
 281        }
 282
 283        ret = pcmcia_register_socket(&sock->socket);
 284        if (ret) {
 285                dev_err(&pdev->dev, "failed to register\n");
 286                goto out2;
 287        }
 288
 289        printk(KERN_INFO "MyCable XXS1500 PCMCIA socket services\n");
 290
 291        return 0;
 292
 293out2:
 294        free_irq(gpio_to_irq(GPIO_CDA), sock);
 295out1:
 296        iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
 297out0:
 298        kfree(sock);
 299        return ret;
 300}
 301
 302static int xxs1500_pcmcia_remove(struct platform_device *pdev)
 303{
 304        struct xxs1500_pcmcia_sock *sock = platform_get_drvdata(pdev);
 305
 306        pcmcia_unregister_socket(&sock->socket);
 307        free_irq(gpio_to_irq(GPIO_CDA), sock);
 308        iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
 309        kfree(sock);
 310
 311        return 0;
 312}
 313
 314static struct platform_driver xxs1500_pcmcia_socket_driver = {
 315        .driver = {
 316                .name   = "xxs1500_pcmcia",
 317                .owner  = THIS_MODULE,
 318        },
 319        .probe          = xxs1500_pcmcia_probe,
 320        .remove         = xxs1500_pcmcia_remove,
 321};
 322
 323module_platform_driver(xxs1500_pcmcia_socket_driver);
 324
 325MODULE_LICENSE("GPL");
 326MODULE_DESCRIPTION("PCMCIA Socket Services for MyCable XXS1500 systems");
 327MODULE_AUTHOR("Manuel Lauss");
 328