/*
    include/comedi.h (installed as /usr/include/comedi.h)
    header file for comedi

    COMEDI - Linux Control and Measurement Device Interface
    Copyright (C) 1998-2001 David A. Schleef <ds@schleef.org>

    This program is free software; you can redistribute it and/or modify
    it under the terms of the GNU Lesser General Public License as published by
    the Free Software Foundation; either version 2 of the License, or
    (at your option) any later version.

    This program is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program; if not, write to the Free Software
    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

*/

#ifndef _COMEDI_H
#define _COMEDI_H

#define COMEDI_MAJORVERSION     0
#define COMEDI_MINORVERSION     7
#define COMEDI_MICROVERSION     76
#define VERSION "0.7.76"

/* comedi's major device number */
#define COMEDI_MAJOR 98

/*
   maximum number of minor devices.  This can be increased, although
   kernel structures are currently statically allocated, thus you
   don't want this to be much more than you actually use.
 */
#define COMEDI_NDEVICES 16

/* number of config options in the config structure */
#define COMEDI_NDEVCONFOPTS 32

/*
 * NOTE: 'comedi_config --init-data' is deprecated
 *
 * The following indexes in the config options were used by
 * comedi_config to pass firmware blobs from user space to the
 * comedi drivers. The request_firmware() hotplug interface is
 * now used by all comedi drivers instead.
 */

/* length of nth chunk of firmware data -*/
#define COMEDI_DEVCONF_AUX_DATA3_LENGTH         25
#define COMEDI_DEVCONF_AUX_DATA2_LENGTH         26
#define COMEDI_DEVCONF_AUX_DATA1_LENGTH         27
#define COMEDI_DEVCONF_AUX_DATA0_LENGTH         28
/* most significant 32 bits of pointer address (if needed) */
#define COMEDI_DEVCONF_AUX_DATA_HI              29
/* least significant 32 bits of pointer address */
#define COMEDI_DEVCONF_AUX_DATA_LO              30
#define COMEDI_DEVCONF_AUX_DATA_LENGTH          31      /* total data length */

/* max length of device and driver names */
#define COMEDI_NAMELEN 20

/* packs and unpacks a channel/range number */

#define CR_PACK(chan, rng, aref)                                        \
        ((((aref)&0x3)<<24) | (((rng)&0xff)<<16) | (chan))
#define CR_PACK_FLAGS(chan, range, aref, flags)                         \
        (CR_PACK(chan, range, aref) | ((flags) & CR_FLAGS_MASK))

#define CR_CHAN(a)      ((a)&0xffff)
#define CR_RANGE(a)     (((a)>>16)&0xff)
#define CR_AREF(a)      (((a)>>24)&0x03)

#define CR_FLAGS_MASK   0xfc000000
#define CR_ALT_FILTER   (1<<26)
#define CR_DITHER       CR_ALT_FILTER
#define CR_DEGLITCH     CR_ALT_FILTER
#define CR_ALT_SOURCE   (1<<27)
#define CR_EDGE         (1<<30)
#define CR_INVERT       (1<<31)

#define AREF_GROUND     0x00    /* analog ref = analog ground */
#define AREF_COMMON     0x01    /* analog ref = analog common */
#define AREF_DIFF       0x02    /* analog ref = differential */
#define AREF_OTHER      0x03    /* analog ref = other (undefined) */

/* counters -- these are arbitrary values */
#define GPCT_RESET              0x0001
#define GPCT_SET_SOURCE         0x0002
#define GPCT_SET_GATE           0x0004
#define GPCT_SET_DIRECTION      0x0008
#define GPCT_SET_OPERATION      0x0010
#define GPCT_ARM                0x0020
#define GPCT_DISARM             0x0040
#define GPCT_GET_INT_CLK_FRQ    0x0080

#define GPCT_INT_CLOCK          0x0001
#define GPCT_EXT_PIN            0x0002
#define GPCT_NO_GATE            0x0004
#define GPCT_UP                 0x0008
#define GPCT_DOWN               0x0010
#define GPCT_HWUD               0x0020
#define GPCT_SIMPLE_EVENT       0x0040
#define GPCT_SINGLE_PERIOD      0x0080
#define GPCT_SINGLE_PW          0x0100
#define GPCT_CONT_PULSE_OUT     0x0200
#define GPCT_SINGLE_PULSE_OUT   0x0400

/* instructions */

#define INSN_MASK_WRITE         0x8000000
#define INSN_MASK_READ          0x4000000
#define INSN_MASK_SPECIAL       0x2000000

#define INSN_READ               (0 | INSN_MASK_READ)
#define INSN_WRITE              (1 | INSN_MASK_WRITE)
#define INSN_BITS               (2 | INSN_MASK_READ|INSN_MASK_WRITE)
#define INSN_CONFIG             (3 | INSN_MASK_READ|INSN_MASK_WRITE)
#define INSN_GTOD               (4 | INSN_MASK_READ|INSN_MASK_SPECIAL)
#define INSN_WAIT               (5 | INSN_MASK_WRITE|INSN_MASK_SPECIAL)
#define INSN_INTTRIG            (6 | INSN_MASK_WRITE|INSN_MASK_SPECIAL)

/* trigger flags */
/* These flags are used in comedi_trig structures */

#define TRIG_BOGUS      0x0001  /* do the motions */
#define TRIG_DITHER     0x0002  /* enable dithering */
#define TRIG_DEGLITCH   0x0004  /* enable deglitching */
        /*#define TRIG_RT       0x0008 *//* perform op in real time */
#define TRIG_CONFIG     0x0010  /* perform configuration, not triggering */
#define TRIG_WAKE_EOS   0x0020  /* wake up on end-of-scan events */
        /*#define TRIG_WRITE    0x0040*//* write to bidirectional devices */

/* command flags */
/* These flags are used in comedi_cmd structures */

/* try to use a real-time interrupt while performing command */
#define CMDF_PRIORITY           0x00000008

#define TRIG_RT         CMDF_PRIORITY   /* compatibility definition */

#define CMDF_WRITE              0x00000040
#define TRIG_WRITE      CMDF_WRITE      /* compatibility definition */

#define CMDF_RAWDATA            0x00000080

#define COMEDI_EV_START         0x00040000
#define COMEDI_EV_SCAN_BEGIN    0x00080000
#define COMEDI_EV_CONVERT       0x00100000
#define COMEDI_EV_SCAN_END      0x00200000
#define COMEDI_EV_STOP          0x00400000

#define TRIG_ROUND_MASK         0x00030000
#define TRIG_ROUND_NEAREST      0x00000000
#define TRIG_ROUND_DOWN         0x00010000
#define TRIG_ROUND_UP           0x00020000
#define TRIG_ROUND_UP_NEXT      0x00030000

/* trigger sources */

#define TRIG_ANY        0xffffffff
#define TRIG_INVALID    0x00000000

#define TRIG_NONE       0x00000001 /* never trigger */
#define TRIG_NOW        0x00000002 /* trigger now + N ns */
#define TRIG_FOLLOW     0x00000004 /* trigger on next lower level trig */
#define TRIG_TIME       0x00000008 /* trigger at time N ns */
#define TRIG_TIMER      0x00000010 /* trigger at rate N ns */
#define TRIG_COUNT      0x00000020 /* trigger when count reaches N */
#define TRIG_EXT        0x00000040 /* trigger on external signal N */
#define TRIG_INT        0x00000080 /* trigger on comedi-internal signal N */
#define TRIG_OTHER      0x00000100 /* driver defined */

/* subdevice flags */

#define SDF_BUSY        0x0001  /* device is busy */
#define SDF_BUSY_OWNER  0x0002  /* device is busy with your job */
#define SDF_LOCKED      0x0004  /* subdevice is locked */
#define SDF_LOCK_OWNER  0x0008  /* you own lock */
#define SDF_MAXDATA     0x0010  /* maxdata depends on channel */
#define SDF_FLAGS       0x0020  /* flags depend on channel */
#define SDF_RANGETYPE   0x0040  /* range type depends on channel */
#define SDF_MODE0       0x0080  /* can do mode 0 */
#define SDF_MODE1       0x0100  /* can do mode 1 */
#define SDF_MODE2       0x0200  /* can do mode 2 */
#define SDF_MODE3       0x0400  /* can do mode 3 */
#define SDF_MODE4       0x0800  /* can do mode 4 */
#define SDF_CMD         0x1000  /* can do commands (deprecated) */
#define SDF_SOFT_CALIBRATED     0x2000 /* subdevice uses software calibration */
#define SDF_CMD_WRITE           0x4000 /* can do output commands */
#define SDF_CMD_READ            0x8000 /* can do input commands */

/* subdevice can be read (e.g. analog input) */
#define SDF_READABLE    0x00010000
/* subdevice can be written (e.g. analog output) */
#define SDF_WRITABLE    0x00020000
#define SDF_WRITEABLE   SDF_WRITABLE    /* spelling error in API */
/* subdevice does not have externally visible lines */
#define SDF_INTERNAL    0x00040000
#define SDF_GROUND      0x00100000      /* can do aref=ground */
#define SDF_COMMON      0x00200000      /* can do aref=common */
#define SDF_DIFF        0x00400000      /* can do aref=diff */
#define SDF_OTHER       0x00800000      /* can do aref=other */
#define SDF_DITHER      0x01000000      /* can do dithering */
#define SDF_DEGLITCH    0x02000000      /* can do deglitching */
#define SDF_MMAP        0x04000000      /* can do mmap() */
#define SDF_RUNNING     0x08000000      /* subdevice is acquiring data */
#define SDF_LSAMPL      0x10000000      /* subdevice uses 32-bit samples */
#define SDF_PACKED      0x20000000      /* subdevice can do packed DIO */
/* re recyle these flags for PWM */
#define SDF_PWM_COUNTER SDF_MODE0       /* PWM can automatically switch off */
#define SDF_PWM_HBRIDGE SDF_MODE1       /* PWM is signed (H-bridge) */

/* subdevice types */

enum comedi_subdevice_type {
        COMEDI_SUBD_UNUSED,     /* unused by driver */
        COMEDI_SUBD_AI,         /* analog input */
        COMEDI_SUBD_AO,         /* analog output */
        COMEDI_SUBD_DI,         /* digital input */
        COMEDI_SUBD_DO,         /* digital output */
        COMEDI_SUBD_DIO,        /* digital input/output */
        COMEDI_SUBD_COUNTER,    /* counter */
        COMEDI_SUBD_TIMER,      /* timer */
        COMEDI_SUBD_MEMORY,     /* memory, EEPROM, DPRAM */
        COMEDI_SUBD_CALIB,      /* calibration DACs */
        COMEDI_SUBD_PROC,       /* processor, DSP */
        COMEDI_SUBD_SERIAL,     /* serial IO */
        COMEDI_SUBD_PWM         /* PWM */
};

/* configuration instructions */

enum configuration_ids {
        INSN_CONFIG_DIO_INPUT = 0,
        INSN_CONFIG_DIO_OUTPUT = 1,
        INSN_CONFIG_DIO_OPENDRAIN = 2,
        INSN_CONFIG_ANALOG_TRIG = 16,
/*      INSN_CONFIG_WAVEFORM = 17, */
/*      INSN_CONFIG_TRIG = 18, */
/*      INSN_CONFIG_COUNTER = 19, */
        INSN_CONFIG_ALT_SOURCE = 20,
        INSN_CONFIG_DIGITAL_TRIG = 21,
        INSN_CONFIG_BLOCK_SIZE = 22,
        INSN_CONFIG_TIMER_1 = 23,
        INSN_CONFIG_FILTER = 24,
        INSN_CONFIG_CHANGE_NOTIFY = 25,

        INSN_CONFIG_SERIAL_CLOCK = 26,  /*ALPHA*/
        INSN_CONFIG_BIDIRECTIONAL_DATA = 27,
        INSN_CONFIG_DIO_QUERY = 28,
        INSN_CONFIG_PWM_OUTPUT = 29,
        INSN_CONFIG_GET_PWM_OUTPUT = 30,
        INSN_CONFIG_ARM = 31,
        INSN_CONFIG_DISARM = 32,
        INSN_CONFIG_GET_COUNTER_STATUS = 33,
        INSN_CONFIG_RESET = 34,
        /* Use CTR as single pulsegenerator */
        INSN_CONFIG_GPCT_SINGLE_PULSE_GENERATOR = 1001,
        /* Use CTR as pulsetraingenerator */
        INSN_CONFIG_GPCT_PULSE_TRAIN_GENERATOR = 1002,
        /* Use the counter as encoder */
        INSN_CONFIG_GPCT_QUADRATURE_ENCODER = 1003,
        INSN_CONFIG_SET_GATE_SRC = 2001,        /* Set gate source */
        INSN_CONFIG_GET_GATE_SRC = 2002,        /* Get gate source */
        /* Set master clock source */
        INSN_CONFIG_SET_CLOCK_SRC = 2003,
        INSN_CONFIG_GET_CLOCK_SRC = 2004, /* Get master clock source */
        INSN_CONFIG_SET_OTHER_SRC = 2005, /* Set other source */
        /* INSN_CONFIG_GET_OTHER_SRC = 2006,*//* Get other source */
        /* Get size in bytes of subdevice's on-board fifos used during
         * streaming input/output */
        INSN_CONFIG_GET_HARDWARE_BUFFER_SIZE = 2006,
        INSN_CONFIG_SET_COUNTER_MODE = 4097,
        /* INSN_CONFIG_8254_SET_MODE is deprecated */
        INSN_CONFIG_8254_SET_MODE = INSN_CONFIG_SET_COUNTER_MODE,
        INSN_CONFIG_8254_READ_STATUS = 4098,
        INSN_CONFIG_SET_ROUTING = 4099,
        INSN_CONFIG_GET_ROUTING = 4109,
        /* PWM */
        INSN_CONFIG_PWM_SET_PERIOD = 5000,      /* sets frequency */
        INSN_CONFIG_PWM_GET_PERIOD = 5001,      /* gets frequency */
        INSN_CONFIG_GET_PWM_STATUS = 5002,      /* is it running? */
        /* sets H bridge: duty cycle and sign bit for a relay at the
         * same time */
        INSN_CONFIG_PWM_SET_H_BRIDGE = 5003,
        /* gets H bridge data: duty cycle and the sign bit */
        INSN_CONFIG_PWM_GET_H_BRIDGE = 5004
};

/*
 * Settings for INSN_CONFIG_DIGITAL_TRIG:
 * data[0] = INSN_CONFIG_DIGITAL_TRIG
 * data[1] = trigger ID
 * data[2] = configuration operation
 * data[3] = configuration parameter 1
 * data[4] = configuration parameter 2
 * data[5] = configuration parameter 3
 *
 * operation                           parameter 1   parameter 2   parameter 3
 * ---------------------------------   -----------   -----------   -----------
 * COMEDI_DIGITAL_TRIG_DISABLE
 * COMEDI_DIGITAL_TRIG_ENABLE_EDGES    left-shift    rising-edges  falling-edges
 * COMEDI_DIGITAL_TRIG_ENABLE_LEVELS   left-shift    high-levels   low-levels
 *
 * COMEDI_DIGITAL_TRIG_DISABLE returns the trigger to its default, inactive,
 * unconfigured state.
 *
 * COMEDI_DIGITAL_TRIG_ENABLE_EDGES sets the rising and/or falling edge inputs
 * that each can fire the trigger.
 *
 * COMEDI_DIGITAL_TRIG_ENABLE_LEVELS sets a combination of high and/or low
 * level inputs that can fire the trigger.
 *
 * "left-shift" is useful if the trigger has more than 32 inputs to specify the
 * first input for this configuration.
 *
 * Some sequences of INSN_CONFIG_DIGITAL_TRIG instructions may have a (partly)
 * accumulative effect, depending on the low-level driver.  This is useful
 * when setting up a trigger that has more than 32 inputs or has a combination
 * of edge and level triggered inputs.
 */
enum comedi_digital_trig_op {
        COMEDI_DIGITAL_TRIG_DISABLE = 0,
        COMEDI_DIGITAL_TRIG_ENABLE_EDGES = 1,
        COMEDI_DIGITAL_TRIG_ENABLE_LEVELS = 2
};

enum comedi_io_direction {
        COMEDI_INPUT = 0,
        COMEDI_OUTPUT = 1,
        COMEDI_OPENDRAIN = 2
};

enum comedi_support_level {
        COMEDI_UNKNOWN_SUPPORT = 0,
        COMEDI_SUPPORTED,
        COMEDI_UNSUPPORTED
};

/* ioctls */

#define CIO 'd'
#define COMEDI_DEVCONFIG _IOW(CIO, 0, struct comedi_devconfig)
#define COMEDI_DEVINFO _IOR(CIO, 1, struct comedi_devinfo)
#define COMEDI_SUBDINFO _IOR(CIO, 2, struct comedi_subdinfo)
#define COMEDI_CHANINFO _IOR(CIO, 3, struct comedi_chaninfo)
#define COMEDI_TRIG _IOWR(CIO, 4, comedi_trig)
#define COMEDI_LOCK _IO(CIO, 5)
#define COMEDI_UNLOCK _IO(CIO, 6)
#define COMEDI_CANCEL _IO(CIO, 7)
#define COMEDI_RANGEINFO _IOR(CIO, 8, struct comedi_rangeinfo)
#define COMEDI_CMD _IOR(CIO, 9, struct comedi_cmd)
#define COMEDI_CMDTEST _IOR(CIO, 10, struct comedi_cmd)
#define COMEDI_INSNLIST _IOR(CIO, 11, struct comedi_insnlist)
#define COMEDI_INSN _IOR(CIO, 12, struct comedi_insn)
#define COMEDI_BUFCONFIG _IOR(CIO, 13, struct comedi_bufconfig)
#define COMEDI_BUFINFO _IOWR(CIO, 14, struct comedi_bufinfo)
#define COMEDI_POLL _IO(CIO, 15)

/* structures */

struct comedi_trig {
        unsigned int subdev;    /* subdevice */
        unsigned int mode;      /* mode */
        unsigned int flags;
        unsigned int n_chan;    /* number of channels */
        unsigned int *chanlist; /* channel/range list */
        short *data;            /* data list, size depends on subd flags */
        unsigned int n;         /* number of scans */
        unsigned int trigsrc;
        unsigned int trigvar;
        unsigned int trigvar1;
        unsigned int data_len;
        unsigned int unused[3];
};

struct comedi_insn {
        unsigned int insn;
        unsigned int n;
        unsigned int __user *data;
        unsigned int subdev;
        unsigned int chanspec;
        unsigned int unused[3];
};

struct comedi_insnlist {
        unsigned int n_insns;
        struct comedi_insn __user *insns;
};

struct comedi_cmd {
        unsigned int subdev;
        unsigned int flags;

        unsigned int start_src;
        unsigned int start_arg;

        unsigned int scan_begin_src;
        unsigned int scan_begin_arg;

        unsigned int convert_src;
        unsigned int convert_arg;

        unsigned int scan_end_src;
        unsigned int scan_end_arg;

        unsigned int stop_src;
        unsigned int stop_arg;

        unsigned int *chanlist; /* channel/range list */
        unsigned int chanlist_len;

        short __user *data; /* data list, size depends on subd flags */
        unsigned int data_len;
};

struct comedi_chaninfo {
        unsigned int subdev;
        unsigned int __user *maxdata_list;
        unsigned int __user *flaglist;
        unsigned int __user *rangelist;
        unsigned int unused[4];
};

struct comedi_rangeinfo {
        unsigned int range_type;
        void __user *range_ptr;
};

struct comedi_krange {
        int min;        /* fixed point, multiply by 1e-6 */
        int max;        /* fixed point, multiply by 1e-6 */
        unsigned int flags;
};

struct comedi_subdinfo {
        unsigned int type;
        unsigned int n_chan;
        unsigned int subd_flags;
        unsigned int timer_type;
        unsigned int len_chanlist;
        unsigned int maxdata;
        unsigned int flags;             /* channel flags */
        unsigned int range_type;        /* lookup in kernel */
        unsigned int settling_time_0;
        /* see support_level enum for values */
        unsigned insn_bits_support;
        unsigned int unused[8];
};

struct comedi_devinfo {
        unsigned int version_code;
        unsigned int n_subdevs;
        char driver_name[COMEDI_NAMELEN];
        char board_name[COMEDI_NAMELEN];
        int read_subdevice;
        int write_subdevice;
        int unused[30];
};

struct comedi_devconfig {
        char board_name[COMEDI_NAMELEN];
        int options[COMEDI_NDEVCONFOPTS];
};

struct comedi_bufconfig {
        unsigned int subdevice;
        unsigned int flags;

        unsigned int maximum_size;
        unsigned int size;

        unsigned int unused[4];
};

struct comedi_bufinfo {
        unsigned int subdevice;
        unsigned int bytes_read;

        unsigned int buf_write_ptr;
        unsigned int buf_read_ptr;
        unsigned int buf_write_count;
        unsigned int buf_read_count;

        unsigned int bytes_written;

        unsigned int unused[4];
};

/* range stuff */

#define __RANGE(a, b)   ((((a)&0xffff)<<16)|((b)&0xffff))

#define RANGE_OFFSET(a)         (((a)>>16)&0xffff)
#define RANGE_LENGTH(b)         ((b)&0xffff)

#define RF_UNIT(flags)          ((flags)&0xff)
#define RF_EXTERNAL             (1<<8)

#define UNIT_volt               0
#define UNIT_mA                 1
#define UNIT_none               2

#define COMEDI_MIN_SPEED        ((unsigned int)0xffffffff)

/* callback stuff */
/* only relevant to kernel modules. */

#define COMEDI_CB_EOS           1       /* end of scan */
#define COMEDI_CB_EOA           2       /* end of acquisition/output */
#define COMEDI_CB_BLOCK         4       /* data has arrived:
                                         * wakes up read() / write() */
#define COMEDI_CB_EOBUF         8       /* DEPRECATED: end of buffer */
#define COMEDI_CB_ERROR         16      /* card error during acquisition */
#define COMEDI_CB_OVERFLOW      32      /* buffer overflow/underflow */

/**********************************************************/
/* everything after this line is ALPHA */
/**********************************************************/

/*
  8254 specific configuration.

  It supports two config commands:

  0 ID: INSN_CONFIG_SET_COUNTER_MODE
  1 8254 Mode
    I8254_MODE0, I8254_MODE1, ..., I8254_MODE5
    OR'ed with:
    I8254_BCD, I8254_BINARY

  0 ID: INSN_CONFIG_8254_READ_STATUS
  1 <-- Status byte returned here.
    B7 = Output
    B6 = NULL Count
    B5 - B0 Current mode.

*/

enum i8254_mode {
        I8254_MODE0 = (0 << 1), /* Interrupt on terminal count */
        I8254_MODE1 = (1 << 1), /* Hardware retriggerable one-shot */
        I8254_MODE2 = (2 << 1), /* Rate generator */
        I8254_MODE3 = (3 << 1), /* Square wave mode */
        I8254_MODE4 = (4 << 1), /* Software triggered strobe */
        I8254_MODE5 = (5 << 1), /* Hardware triggered strobe
                                 * (retriggerable) */
        I8254_BCD = 1,          /* use binary-coded decimal instead of binary
                                 * (pretty useless) */
        I8254_BINARY = 0
};

static inline unsigned NI_USUAL_PFI_SELECT(unsigned pfi_channel)
{
        if (pfi_channel < 10)
                return 0x1 + pfi_channel;
        else
                return 0xb + pfi_channel;
}

static inline unsigned NI_USUAL_RTSI_SELECT(unsigned rtsi_channel)
{
        if (rtsi_channel < 7)
                return 0xb + rtsi_channel;
        else
                return 0x1b;
}

/* mode bits for NI general-purpose counters, set with
 * INSN_CONFIG_SET_COUNTER_MODE */
#define NI_GPCT_COUNTING_MODE_SHIFT 16
#define NI_GPCT_INDEX_PHASE_BITSHIFT 20
#define NI_GPCT_COUNTING_DIRECTION_SHIFT 24
enum ni_gpct_mode_bits {
        NI_GPCT_GATE_ON_BOTH_EDGES_BIT = 0x4,
        NI_GPCT_EDGE_GATE_MODE_MASK = 0x18,
        NI_GPCT_EDGE_GATE_STARTS_STOPS_BITS = 0x0,
        NI_GPCT_EDGE_GATE_STOPS_STARTS_BITS = 0x8,
        NI_GPCT_EDGE_GATE_STARTS_BITS = 0x10,
        NI_GPCT_EDGE_GATE_NO_STARTS_NO_STOPS_BITS = 0x18,
        NI_GPCT_STOP_MODE_MASK = 0x60,
        NI_GPCT_STOP_ON_GATE_BITS = 0x00,
        NI_GPCT_STOP_ON_GATE_OR_TC_BITS = 0x20,
        NI_GPCT_STOP_ON_GATE_OR_SECOND_TC_BITS = 0x40,
        NI_GPCT_LOAD_B_SELECT_BIT = 0x80,
        NI_GPCT_OUTPUT_MODE_MASK = 0x300,
        NI_GPCT_OUTPUT_TC_PULSE_BITS = 0x100,
        NI_GPCT_OUTPUT_TC_TOGGLE_BITS = 0x200,
        NI_GPCT_OUTPUT_TC_OR_GATE_TOGGLE_BITS = 0x300,
        NI_GPCT_HARDWARE_DISARM_MASK = 0xc00,
        NI_GPCT_NO_HARDWARE_DISARM_BITS = 0x000,
        NI_GPCT_DISARM_AT_TC_BITS = 0x400,
        NI_GPCT_DISARM_AT_GATE_BITS = 0x800,
        NI_GPCT_DISARM_AT_TC_OR_GATE_BITS = 0xc00,
        NI_GPCT_LOADING_ON_TC_BIT = 0x1000,
        NI_GPCT_LOADING_ON_GATE_BIT = 0x4000,
        NI_GPCT_COUNTING_MODE_MASK = 0x7 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_NORMAL_BITS =
                0x0 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_QUADRATURE_X1_BITS =
                0x1 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_QUADRATURE_X2_BITS =
                0x2 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_QUADRATURE_X4_BITS =
                0x3 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_TWO_PULSE_BITS =
                0x4 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_COUNTING_MODE_SYNC_SOURCE_BITS =
                0x6 << NI_GPCT_COUNTING_MODE_SHIFT,
        NI_GPCT_INDEX_PHASE_MASK = 0x3 << NI_GPCT_INDEX_PHASE_BITSHIFT,
        NI_GPCT_INDEX_PHASE_LOW_A_LOW_B_BITS =
                0x0 << NI_GPCT_INDEX_PHASE_BITSHIFT,
        NI_GPCT_INDEX_PHASE_LOW_A_HIGH_B_BITS =
                0x1 << NI_GPCT_INDEX_PHASE_BITSHIFT,
        NI_GPCT_INDEX_PHASE_HIGH_A_LOW_B_BITS =
                0x2 << NI_GPCT_INDEX_PHASE_BITSHIFT,
        NI_GPCT_INDEX_PHASE_HIGH_A_HIGH_B_BITS =
                0x3 << NI_GPCT_INDEX_PHASE_BITSHIFT,
        NI_GPCT_INDEX_ENABLE_BIT = 0x400000,
        NI_GPCT_COUNTING_DIRECTION_MASK =
                0x3 << NI_GPCT_COUNTING_DIRECTION_SHIFT,
        NI_GPCT_COUNTING_DIRECTION_DOWN_BITS =
                0x00 << NI_GPCT_COUNTING_DIRECTION_SHIFT,
        NI_GPCT_COUNTING_DIRECTION_UP_BITS =
                0x1 << NI_GPCT_COUNTING_DIRECTION_SHIFT,
        NI_GPCT_COUNTING_DIRECTION_HW_UP_DOWN_BITS =
                0x2 << NI_GPCT_COUNTING_DIRECTION_SHIFT,
        NI_GPCT_COUNTING_DIRECTION_HW_GATE_BITS =
                0x3 << NI_GPCT_COUNTING_DIRECTION_SHIFT,
        NI_GPCT_RELOAD_SOURCE_MASK = 0xc000000,
        NI_GPCT_RELOAD_SOURCE_FIXED_BITS = 0x0,
        NI_GPCT_RELOAD_SOURCE_SWITCHING_BITS = 0x4000000,
        NI_GPCT_RELOAD_SOURCE_GATE_SELECT_BITS = 0x8000000,
        NI_GPCT_OR_GATE_BIT = 0x10000000,
        NI_GPCT_INVERT_OUTPUT_BIT = 0x20000000
};

/* Bits for setting a clock source with
 * INSN_CONFIG_SET_CLOCK_SRC when using NI general-purpose counters. */
enum ni_gpct_clock_source_bits {
        NI_GPCT_CLOCK_SRC_SELECT_MASK = 0x3f,
        NI_GPCT_TIMEBASE_1_CLOCK_SRC_BITS = 0x0,
        NI_GPCT_TIMEBASE_2_CLOCK_SRC_BITS = 0x1,
        NI_GPCT_TIMEBASE_3_CLOCK_SRC_BITS = 0x2,
        NI_GPCT_LOGIC_LOW_CLOCK_SRC_BITS = 0x3,
        NI_GPCT_NEXT_GATE_CLOCK_SRC_BITS = 0x4,
        NI_GPCT_NEXT_TC_CLOCK_SRC_BITS = 0x5,
        /* NI 660x-specific */
        NI_GPCT_SOURCE_PIN_i_CLOCK_SRC_BITS = 0x6,
        NI_GPCT_PXI10_CLOCK_SRC_BITS = 0x7,
        NI_GPCT_PXI_STAR_TRIGGER_CLOCK_SRC_BITS = 0x8,
        NI_GPCT_ANALOG_TRIGGER_OUT_CLOCK_SRC_BITS = 0x9,
        NI_GPCT_PRESCALE_MODE_CLOCK_SRC_MASK = 0x30000000,
        NI_GPCT_NO_PRESCALE_CLOCK_SRC_BITS = 0x0,
        /* divide source by 2 */
        NI_GPCT_PRESCALE_X2_CLOCK_SRC_BITS = 0x10000000,
        /* divide source by 8 */
        NI_GPCT_PRESCALE_X8_CLOCK_SRC_BITS = 0x20000000,
        NI_GPCT_INVERT_CLOCK_SRC_BIT = 0x80000000
};
static inline unsigned NI_GPCT_SOURCE_PIN_CLOCK_SRC_BITS(unsigned n)
{
        /* NI 660x-specific */
        return 0x10 + n;
}
static inline unsigned NI_GPCT_RTSI_CLOCK_SRC_BITS(unsigned n)
{
        return 0x18 + n;
}
static inline unsigned NI_GPCT_PFI_CLOCK_SRC_BITS(unsigned n)
{
        /* no pfi on NI 660x */
        return 0x20 + n;
}

/* Possibilities for setting a gate source with
INSN_CONFIG_SET_GATE_SRC when using NI general-purpose counters.
May be bitwise-or'd with CR_EDGE or CR_INVERT. */
enum ni_gpct_gate_select {
        /* m-series gates */
        NI_GPCT_TIMESTAMP_MUX_GATE_SELECT = 0x0,
        NI_GPCT_AI_START2_GATE_SELECT = 0x12,
        NI_GPCT_PXI_STAR_TRIGGER_GATE_SELECT = 0x13,
        NI_GPCT_NEXT_OUT_GATE_SELECT = 0x14,
        NI_GPCT_AI_START1_GATE_SELECT = 0x1c,
        NI_GPCT_NEXT_SOURCE_GATE_SELECT = 0x1d,
        NI_GPCT_ANALOG_TRIGGER_OUT_GATE_SELECT = 0x1e,
        NI_GPCT_LOGIC_LOW_GATE_SELECT = 0x1f,
        /* more gates for 660x */
        NI_GPCT_SOURCE_PIN_i_GATE_SELECT = 0x100,
        NI_GPCT_GATE_PIN_i_GATE_SELECT = 0x101,
        /* more gates for 660x "second gate" */
        NI_GPCT_UP_DOWN_PIN_i_GATE_SELECT = 0x201,
        NI_GPCT_SELECTED_GATE_GATE_SELECT = 0x21e,
        /* m-series "second gate" sources are unknown,
         * we should add them here with an offset of 0x300 when
         * known. */
        NI_GPCT_DISABLED_GATE_SELECT = 0x8000,
};
static inline unsigned NI_GPCT_GATE_PIN_GATE_SELECT(unsigned n)
{
        return 0x102 + n;
}
static inline unsigned NI_GPCT_RTSI_GATE_SELECT(unsigned n)
{
        return NI_USUAL_RTSI_SELECT(n);
}
static inline unsigned NI_GPCT_PFI_GATE_SELECT(unsigned n)
{
        return NI_USUAL_PFI_SELECT(n);
}
static inline unsigned NI_GPCT_UP_DOWN_PIN_GATE_SELECT(unsigned n)
{
        return 0x202 + n;
}

/* Possibilities for setting a source with
INSN_CONFIG_SET_OTHER_SRC when using NI general-purpose counters. */
enum ni_gpct_other_index {
        NI_GPCT_SOURCE_ENCODER_A,
        NI_GPCT_SOURCE_ENCODER_B,
        NI_GPCT_SOURCE_ENCODER_Z
};
enum ni_gpct_other_select {
        /* m-series gates */
        /* Still unknown, probably only need NI_GPCT_PFI_OTHER_SELECT */
        NI_GPCT_DISABLED_OTHER_SELECT = 0x8000,
};
static inline unsigned NI_GPCT_PFI_OTHER_SELECT(unsigned n)
{
        return NI_USUAL_PFI_SELECT(n);
}

/* start sources for ni general-purpose counters for use with
INSN_CONFIG_ARM */
enum ni_gpct_arm_source {
        NI_GPCT_ARM_IMMEDIATE = 0x0,
        NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter
                                             * and the adjacent paired
                                             * counter simultaneously */
        /* NI doesn't document bits for selecting hardware arm triggers.
         * If the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least
         * significant bits (3 bits for 660x or 5 bits for m-series)
         * through to the hardware.  This will at least allow someone to
         * figure out what the bits do later. */
        NI_GPCT_ARM_UNKNOWN = 0x1000,
};

/* digital filtering options for ni 660x for use with INSN_CONFIG_FILTER. */
enum ni_gpct_filter_select {
        NI_GPCT_FILTER_OFF = 0x0,
        NI_GPCT_FILTER_TIMEBASE_3_SYNC = 0x1,
        NI_GPCT_FILTER_100x_TIMEBASE_1 = 0x2,
        NI_GPCT_FILTER_20x_TIMEBASE_1 = 0x3,
        NI_GPCT_FILTER_10x_TIMEBASE_1 = 0x4,
        NI_GPCT_FILTER_2x_TIMEBASE_1 = 0x5,
        NI_GPCT_FILTER_2x_TIMEBASE_3 = 0x6
};

/* PFI digital filtering options for ni m-series for use with
 * INSN_CONFIG_FILTER. */
enum ni_pfi_filter_select {
        NI_PFI_FILTER_OFF = 0x0,
        NI_PFI_FILTER_125ns = 0x1,
        NI_PFI_FILTER_6425ns = 0x2,
        NI_PFI_FILTER_2550us = 0x3
};

/* master clock sources for ni mio boards and INSN_CONFIG_SET_CLOCK_SRC */
enum ni_mio_clock_source {
        NI_MIO_INTERNAL_CLOCK = 0,
        NI_MIO_RTSI_CLOCK = 1,  /* doesn't work for m-series, use
                                   NI_MIO_PLL_RTSI_CLOCK() */
        /* the NI_MIO_PLL_* sources are m-series only */
        NI_MIO_PLL_PXI_STAR_TRIGGER_CLOCK = 2,
        NI_MIO_PLL_PXI10_CLOCK = 3,
        NI_MIO_PLL_RTSI0_CLOCK = 4
};
static inline unsigned NI_MIO_PLL_RTSI_CLOCK(unsigned rtsi_channel)
{
        return NI_MIO_PLL_RTSI0_CLOCK + rtsi_channel;
}

/* Signals which can be routed to an NI RTSI pin with INSN_CONFIG_SET_ROUTING.
 The numbers assigned are not arbitrary, they correspond to the bits required
 to program the board. */
enum ni_rtsi_routing {
        NI_RTSI_OUTPUT_ADR_START1 = 0,
        NI_RTSI_OUTPUT_ADR_START2 = 1,
        NI_RTSI_OUTPUT_SCLKG = 2,
        NI_RTSI_OUTPUT_DACUPDN = 3,
        NI_RTSI_OUTPUT_DA_START1 = 4,
        NI_RTSI_OUTPUT_G_SRC0 = 5,
        NI_RTSI_OUTPUT_G_GATE0 = 6,
        NI_RTSI_OUTPUT_RGOUT0 = 7,
        NI_RTSI_OUTPUT_RTSI_BRD_0 = 8,
        NI_RTSI_OUTPUT_RTSI_OSC = 12    /* pre-m-series always have RTSI
                                         * clock on line 7 */
};
static inline unsigned NI_RTSI_OUTPUT_RTSI_BRD(unsigned n)
{
        return NI_RTSI_OUTPUT_RTSI_BRD_0 + n;
}

/* Signals which can be routed to an NI PFI pin on an m-series board with
 * INSN_CONFIG_SET_ROUTING.  These numbers are also returned by
 * INSN_CONFIG_GET_ROUTING on pre-m-series boards, even though their routing
 * cannot be changed.  The numbers assigned are not arbitrary, they correspond
 * to the bits required to program the board. */
enum ni_pfi_routing {
        NI_PFI_OUTPUT_PFI_DEFAULT = 0,
        NI_PFI_OUTPUT_AI_START1 = 1,
        NI_PFI_OUTPUT_AI_START2 = 2,
        NI_PFI_OUTPUT_AI_CONVERT = 3,
        NI_PFI_OUTPUT_G_SRC1 = 4,
        NI_PFI_OUTPUT_G_GATE1 = 5,
        NI_PFI_OUTPUT_AO_UPDATE_N = 6,
        NI_PFI_OUTPUT_AO_START1 = 7,
        NI_PFI_OUTPUT_AI_START_PULSE = 8,
        NI_PFI_OUTPUT_G_SRC0 = 9,
        NI_PFI_OUTPUT_G_GATE0 = 10,
        NI_PFI_OUTPUT_EXT_STROBE = 11,
        NI_PFI_OUTPUT_AI_EXT_MUX_CLK = 12,
        NI_PFI_OUTPUT_GOUT0 = 13,
        NI_PFI_OUTPUT_GOUT1 = 14,
        NI_PFI_OUTPUT_FREQ_OUT = 15,
        NI_PFI_OUTPUT_PFI_DO = 16,
        NI_PFI_OUTPUT_I_ATRIG = 17,
        NI_PFI_OUTPUT_RTSI0 = 18,
        NI_PFI_OUTPUT_PXI_STAR_TRIGGER_IN = 26,
        NI_PFI_OUTPUT_SCXI_TRIG1 = 27,
        NI_PFI_OUTPUT_DIO_CHANGE_DETECT_RTSI = 28,
        NI_PFI_OUTPUT_CDI_SAMPLE = 29,
        NI_PFI_OUTPUT_CDO_UPDATE = 30
};
static inline unsigned NI_PFI_OUTPUT_RTSI(unsigned rtsi_channel)
{
        return NI_PFI_OUTPUT_RTSI0 + rtsi_channel;
}

/* Signals which can be routed to output on a NI PFI pin on a 660x board
 with INSN_CONFIG_SET_ROUTING.  The numbers assigned are
 not arbitrary, they correspond to the bits required
 to program the board.  Lines 0 to 7 can only be set to
 NI_660X_PFI_OUTPUT_DIO.  Lines 32 to 39 can only be set to
 NI_660X_PFI_OUTPUT_COUNTER. */
enum ni_660x_pfi_routing {
        NI_660X_PFI_OUTPUT_COUNTER = 1, /* counter */
        NI_660X_PFI_OUTPUT_DIO = 2,     /* static digital output */
};

/* NI External Trigger lines.  These values are not arbitrary, but are related
 * to the bits required to program the board (offset by 1 for historical
 * reasons). */
static inline unsigned NI_EXT_PFI(unsigned pfi_channel)
{
        return NI_USUAL_PFI_SELECT(pfi_channel) - 1;
}
static inline unsigned NI_EXT_RTSI(unsigned rtsi_channel)
{
        return NI_USUAL_RTSI_SELECT(rtsi_channel) - 1;
}

/* status bits for INSN_CONFIG_GET_COUNTER_STATUS */
enum comedi_counter_status_flags {
        COMEDI_COUNTER_ARMED = 0x1,
        COMEDI_COUNTER_COUNTING = 0x2,
        COMEDI_COUNTER_TERMINAL_COUNT = 0x4,
};

/* Clock sources for CDIO subdevice on NI m-series boards.  Used as the
 * scan_begin_arg for a comedi_command. These sources may also be bitwise-or'd
 * with CR_INVERT to change polarity. */
enum ni_m_series_cdio_scan_begin_src {
        NI_CDIO_SCAN_BEGIN_SRC_GROUND = 0,
        NI_CDIO_SCAN_BEGIN_SRC_AI_START = 18,
        NI_CDIO_SCAN_BEGIN_SRC_AI_CONVERT = 19,
        NI_CDIO_SCAN_BEGIN_SRC_PXI_STAR_TRIGGER = 20,
        NI_CDIO_SCAN_BEGIN_SRC_G0_OUT = 28,
        NI_CDIO_SCAN_BEGIN_SRC_G1_OUT = 29,
        NI_CDIO_SCAN_BEGIN_SRC_ANALOG_TRIGGER = 30,
        NI_CDIO_SCAN_BEGIN_SRC_AO_UPDATE = 31,
        NI_CDIO_SCAN_BEGIN_SRC_FREQ_OUT = 32,
        NI_CDIO_SCAN_BEGIN_SRC_DIO_CHANGE_DETECT_IRQ = 33
};
static inline unsigned NI_CDIO_SCAN_BEGIN_SRC_PFI(unsigned pfi_channel)
{
        return NI_USUAL_PFI_SELECT(pfi_channel);
}
static inline unsigned NI_CDIO_SCAN_BEGIN_SRC_RTSI(unsigned rtsi_channel)
{
        return NI_USUAL_RTSI_SELECT(rtsi_channel);
}

/* scan_begin_src for scan_begin_arg==TRIG_EXT with analog output command on NI
 * boards.  These scan begin sources can also be bitwise-or'd with CR_INVERT to
 * change polarity. */
static inline unsigned NI_AO_SCAN_BEGIN_SRC_PFI(unsigned pfi_channel)
{
        return NI_USUAL_PFI_SELECT(pfi_channel);
}
static inline unsigned NI_AO_SCAN_BEGIN_SRC_RTSI(unsigned rtsi_channel)
{
        return NI_USUAL_RTSI_SELECT(rtsi_channel);
}

/* Bits for setting a clock source with
 * INSN_CONFIG_SET_CLOCK_SRC when using NI frequency output subdevice. */
enum ni_freq_out_clock_source_bits {
        NI_FREQ_OUT_TIMEBASE_1_DIV_2_CLOCK_SRC, /* 10 MHz */
        NI_FREQ_OUT_TIMEBASE_2_CLOCK_SRC        /* 100 KHz */
};

/* Values for setting a clock source with INSN_CONFIG_SET_CLOCK_SRC for
 * 8254 counter subdevices on Amplicon DIO boards (amplc_dio200 driver). */
enum amplc_dio_clock_source {
        AMPLC_DIO_CLK_CLKN,     /* per channel external clock
                                   input/output pin (pin is only an
                                   input when clock source set to this
                                   value, otherwise it is an output) */
        AMPLC_DIO_CLK_10MHZ,    /* 10 MHz internal clock */
        AMPLC_DIO_CLK_1MHZ,     /* 1 MHz internal clock */
        AMPLC_DIO_CLK_100KHZ,   /* 100 kHz internal clock */
        AMPLC_DIO_CLK_10KHZ,    /* 10 kHz internal clock */
        AMPLC_DIO_CLK_1KHZ,     /* 1 kHz internal clock */
        AMPLC_DIO_CLK_OUTNM1,   /* output of preceding counter channel
                                   (for channel 0, preceding counter
                                   channel is channel 2 on preceding
                                   counter subdevice, for first counter
                                   subdevice, preceding counter
                                   subdevice is the last counter
                                   subdevice) */
        AMPLC_DIO_CLK_EXT,      /* per chip external input pin */
        /* the following are "enhanced" clock sources for PCIe models */
        AMPLC_DIO_CLK_VCC,      /* clock input HIGH */
        AMPLC_DIO_CLK_GND,      /* clock input LOW */
        AMPLC_DIO_CLK_PAT_PRESENT, /* "pattern present" signal */
        AMPLC_DIO_CLK_20MHZ     /* 20 MHz internal clock */
};

/* Values for setting a clock source with INSN_CONFIG_SET_CLOCK_SRC for
 * timer subdevice on some Amplicon DIO PCIe boards (amplc_dio200 driver). */
enum amplc_dio_ts_clock_src {
        AMPLC_DIO_TS_CLK_1GHZ,  /* 1 ns period with 20 ns granularity */
        AMPLC_DIO_TS_CLK_1MHZ,  /* 1 us period */
        AMPLC_DIO_TS_CLK_1KHZ   /* 1 ms period */
};

/* Values for setting a gate source with INSN_CONFIG_SET_GATE_SRC for
 * 8254 counter subdevices on Amplicon DIO boards (amplc_dio200 driver). */
enum amplc_dio_gate_source {
        AMPLC_DIO_GAT_VCC,      /* internal high logic level */
        AMPLC_DIO_GAT_GND,      /* internal low logic level */
        AMPLC_DIO_GAT_GATN,     /* per channel external gate input */
        AMPLC_DIO_GAT_NOUTNM2,  /* negated output of counter channel
                                   minus 2 (for channels 0 or 1,
                                   channel minus 2 is channel 1 or 2 on
                                   the preceding counter subdevice, for
                                   the first counter subdevice the
                                   preceding counter subdevice is the
                                   last counter subdevice) */
        AMPLC_DIO_GAT_RESERVED4,
        AMPLC_DIO_GAT_RESERVED5,
        AMPLC_DIO_GAT_RESERVED6,
        AMPLC_DIO_GAT_RESERVED7,
        /* the following are "enhanced" gate sources for PCIe models */
        AMPLC_DIO_GAT_NGATN = 6, /* negated per channel gate input */
        AMPLC_DIO_GAT_OUTNM2,   /* non-negated output of counter
                                   channel minus 2 */
        AMPLC_DIO_GAT_PAT_PRESENT, /* "pattern present" signal */
        AMPLC_DIO_GAT_PAT_OCCURRED, /* "pattern occurred" latched */
        AMPLC_DIO_GAT_PAT_GONE, /* "pattern gone away" latched */
        AMPLC_DIO_GAT_NPAT_PRESENT, /* negated "pattern present" */
        AMPLC_DIO_GAT_NPAT_OCCURRED, /* negated "pattern occurred" */
        AMPLC_DIO_GAT_NPAT_GONE /* negated "pattern gone away" */
};

#endif /* _COMEDI_H */