1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16#include <linux/module.h>
17#include <linux/i2c.h>
18#include <linux/interrupt.h>
19#include <linux/input.h>
20#include <linux/irq.h>
21#include <linux/platform_data/mcs.h>
22#include <linux/slab.h>
23
24
25#define MCS5000_TS_STATUS 0x00
26#define STATUS_OFFSET 0
27#define STATUS_NO (0 << STATUS_OFFSET)
28#define STATUS_INIT (1 << STATUS_OFFSET)
29#define STATUS_SENSING (2 << STATUS_OFFSET)
30#define STATUS_COORD (3 << STATUS_OFFSET)
31#define STATUS_GESTURE (4 << STATUS_OFFSET)
32#define ERROR_OFFSET 4
33#define ERROR_NO (0 << ERROR_OFFSET)
34#define ERROR_POWER_ON_RESET (1 << ERROR_OFFSET)
35#define ERROR_INT_RESET (2 << ERROR_OFFSET)
36#define ERROR_EXT_RESET (3 << ERROR_OFFSET)
37#define ERROR_INVALID_REG_ADDRESS (8 << ERROR_OFFSET)
38#define ERROR_INVALID_REG_VALUE (9 << ERROR_OFFSET)
39
40#define MCS5000_TS_OP_MODE 0x01
41#define RESET_OFFSET 0
42#define RESET_NO (0 << RESET_OFFSET)
43#define RESET_EXT_SOFT (1 << RESET_OFFSET)
44#define OP_MODE_OFFSET 1
45#define OP_MODE_SLEEP (0 << OP_MODE_OFFSET)
46#define OP_MODE_ACTIVE (1 << OP_MODE_OFFSET)
47#define GESTURE_OFFSET 4
48#define GESTURE_DISABLE (0 << GESTURE_OFFSET)
49#define GESTURE_ENABLE (1 << GESTURE_OFFSET)
50#define PROXIMITY_OFFSET 5
51#define PROXIMITY_DISABLE (0 << PROXIMITY_OFFSET)
52#define PROXIMITY_ENABLE (1 << PROXIMITY_OFFSET)
53#define SCAN_MODE_OFFSET 6
54#define SCAN_MODE_INTERRUPT (0 << SCAN_MODE_OFFSET)
55#define SCAN_MODE_POLLING (1 << SCAN_MODE_OFFSET)
56#define REPORT_RATE_OFFSET 7
57#define REPORT_RATE_40 (0 << REPORT_RATE_OFFSET)
58#define REPORT_RATE_80 (1 << REPORT_RATE_OFFSET)
59
60#define MCS5000_TS_SENS_CTL 0x02
61#define MCS5000_TS_FILTER_CTL 0x03
62#define PRI_FILTER_OFFSET 0
63#define SEC_FILTER_OFFSET 4
64
65#define MCS5000_TS_X_SIZE_UPPER 0x08
66#define MCS5000_TS_X_SIZE_LOWER 0x09
67#define MCS5000_TS_Y_SIZE_UPPER 0x0A
68#define MCS5000_TS_Y_SIZE_LOWER 0x0B
69
70#define MCS5000_TS_INPUT_INFO 0x10
71#define INPUT_TYPE_OFFSET 0
72#define INPUT_TYPE_NONTOUCH (0 << INPUT_TYPE_OFFSET)
73#define INPUT_TYPE_SINGLE (1 << INPUT_TYPE_OFFSET)
74#define INPUT_TYPE_DUAL (2 << INPUT_TYPE_OFFSET)
75#define INPUT_TYPE_PALM (3 << INPUT_TYPE_OFFSET)
76#define INPUT_TYPE_PROXIMITY (7 << INPUT_TYPE_OFFSET)
77#define GESTURE_CODE_OFFSET 3
78#define GESTURE_CODE_NO (0 << GESTURE_CODE_OFFSET)
79
80#define MCS5000_TS_X_POS_UPPER 0x11
81#define MCS5000_TS_X_POS_LOWER 0x12
82#define MCS5000_TS_Y_POS_UPPER 0x13
83#define MCS5000_TS_Y_POS_LOWER 0x14
84#define MCS5000_TS_Z_POS 0x15
85#define MCS5000_TS_WIDTH 0x16
86#define MCS5000_TS_GESTURE_VAL 0x17
87#define MCS5000_TS_MODULE_REV 0x20
88#define MCS5000_TS_FIRMWARE_VER 0x21
89
90
91#define MCS5000_MAX_XC 0x3ff
92#define MCS5000_MAX_YC 0x3ff
93
94enum mcs5000_ts_read_offset {
95 READ_INPUT_INFO,
96 READ_X_POS_UPPER,
97 READ_X_POS_LOWER,
98 READ_Y_POS_UPPER,
99 READ_Y_POS_LOWER,
100 READ_BLOCK_SIZE,
101};
102
103
104struct mcs5000_ts_data {
105 struct i2c_client *client;
106 struct input_dev *input_dev;
107 const struct mcs_platform_data *platform_data;
108};
109
110static irqreturn_t mcs5000_ts_interrupt(int irq, void *dev_id)
111{
112 struct mcs5000_ts_data *data = dev_id;
113 struct i2c_client *client = data->client;
114 u8 buffer[READ_BLOCK_SIZE];
115 int err;
116 int x;
117 int y;
118
119 err = i2c_smbus_read_i2c_block_data(client, MCS5000_TS_INPUT_INFO,
120 READ_BLOCK_SIZE, buffer);
121 if (err < 0) {
122 dev_err(&client->dev, "%s, err[%d]\n", __func__, err);
123 goto out;
124 }
125
126 switch (buffer[READ_INPUT_INFO]) {
127 case INPUT_TYPE_NONTOUCH:
128 input_report_key(data->input_dev, BTN_TOUCH, 0);
129 input_sync(data->input_dev);
130 break;
131
132 case INPUT_TYPE_SINGLE:
133 x = (buffer[READ_X_POS_UPPER] << 8) | buffer[READ_X_POS_LOWER];
134 y = (buffer[READ_Y_POS_UPPER] << 8) | buffer[READ_Y_POS_LOWER];
135
136 input_report_key(data->input_dev, BTN_TOUCH, 1);
137 input_report_abs(data->input_dev, ABS_X, x);
138 input_report_abs(data->input_dev, ABS_Y, y);
139 input_sync(data->input_dev);
140 break;
141
142 case INPUT_TYPE_DUAL:
143
144 break;
145
146 case INPUT_TYPE_PALM:
147
148 break;
149
150 case INPUT_TYPE_PROXIMITY:
151
152 break;
153
154 default:
155 dev_err(&client->dev, "Unknown ts input type %d\n",
156 buffer[READ_INPUT_INFO]);
157 break;
158 }
159
160 out:
161 return IRQ_HANDLED;
162}
163
164static void mcs5000_ts_phys_init(struct mcs5000_ts_data *data,
165 const struct mcs_platform_data *platform_data)
166{
167 struct i2c_client *client = data->client;
168
169
170 i2c_smbus_write_byte_data(client, MCS5000_TS_OP_MODE,
171 RESET_EXT_SOFT | OP_MODE_SLEEP);
172
173
174 i2c_smbus_write_byte_data(client, MCS5000_TS_X_SIZE_UPPER,
175 platform_data->x_size >> 8);
176 i2c_smbus_write_byte_data(client, MCS5000_TS_X_SIZE_LOWER,
177 platform_data->x_size & 0xff);
178 i2c_smbus_write_byte_data(client, MCS5000_TS_Y_SIZE_UPPER,
179 platform_data->y_size >> 8);
180 i2c_smbus_write_byte_data(client, MCS5000_TS_Y_SIZE_LOWER,
181 platform_data->y_size & 0xff);
182
183
184 i2c_smbus_write_byte_data(data->client, MCS5000_TS_OP_MODE,
185 OP_MODE_ACTIVE | REPORT_RATE_80);
186}
187
188static int mcs5000_ts_probe(struct i2c_client *client,
189 const struct i2c_device_id *id)
190{
191 const struct mcs_platform_data *pdata;
192 struct mcs5000_ts_data *data;
193 struct input_dev *input_dev;
194 int error;
195
196 pdata = dev_get_platdata(&client->dev);
197 if (!pdata)
198 return -EINVAL;
199
200 data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
201 if (!data) {
202 dev_err(&client->dev, "Failed to allocate memory\n");
203 return -ENOMEM;
204 }
205
206 data->client = client;
207
208 input_dev = devm_input_allocate_device(&client->dev);
209 if (!input_dev) {
210 dev_err(&client->dev, "Failed to allocate input device\n");
211 return -ENOMEM;
212 }
213
214 input_dev->name = "MELFAS MCS-5000 Touchscreen";
215 input_dev->id.bustype = BUS_I2C;
216 input_dev->dev.parent = &client->dev;
217
218 __set_bit(EV_ABS, input_dev->evbit);
219 __set_bit(EV_KEY, input_dev->evbit);
220 __set_bit(BTN_TOUCH, input_dev->keybit);
221 input_set_abs_params(input_dev, ABS_X, 0, MCS5000_MAX_XC, 0, 0);
222 input_set_abs_params(input_dev, ABS_Y, 0, MCS5000_MAX_YC, 0, 0);
223
224 data->input_dev = input_dev;
225
226 if (pdata->cfg_pin)
227 pdata->cfg_pin();
228
229 error = devm_request_threaded_irq(&client->dev, client->irq,
230 NULL, mcs5000_ts_interrupt,
231 IRQF_TRIGGER_LOW | IRQF_ONESHOT,
232 "mcs5000_ts", data);
233 if (error) {
234 dev_err(&client->dev, "Failed to register interrupt\n");
235 return error;
236 }
237
238 error = input_register_device(data->input_dev);
239 if (error) {
240 dev_err(&client->dev, "Failed to register input device\n");
241 return error;
242 }
243
244 mcs5000_ts_phys_init(data, pdata);
245 i2c_set_clientdata(client, data);
246
247 return 0;
248}
249
250static int __maybe_unused mcs5000_ts_suspend(struct device *dev)
251{
252 struct i2c_client *client = to_i2c_client(dev);
253
254
255 i2c_smbus_write_byte_data(client, MCS5000_TS_OP_MODE, OP_MODE_SLEEP);
256
257 return 0;
258}
259
260static int __maybe_unused mcs5000_ts_resume(struct device *dev)
261{
262 struct i2c_client *client = to_i2c_client(dev);
263 struct mcs5000_ts_data *data = i2c_get_clientdata(client);
264 const struct mcs_platform_data *pdata = dev_get_platdata(dev);
265
266 mcs5000_ts_phys_init(data, pdata);
267
268 return 0;
269}
270
271static SIMPLE_DEV_PM_OPS(mcs5000_ts_pm, mcs5000_ts_suspend, mcs5000_ts_resume);
272
273static const struct i2c_device_id mcs5000_ts_id[] = {
274 { "mcs5000_ts", 0 },
275 { }
276};
277MODULE_DEVICE_TABLE(i2c, mcs5000_ts_id);
278
279static struct i2c_driver mcs5000_ts_driver = {
280 .probe = mcs5000_ts_probe,
281 .driver = {
282 .name = "mcs5000_ts",
283 .pm = &mcs5000_ts_pm,
284 },
285 .id_table = mcs5000_ts_id,
286};
287
288module_i2c_driver(mcs5000_ts_driver);
289
290
291MODULE_AUTHOR("Joonyoung Shim <jy0922.shim@samsung.com>");
292MODULE_DESCRIPTION("Touchscreen driver for MELFAS MCS-5000 controller");
293MODULE_LICENSE("GPL");
294
