/*
 * st_spi_fsm.c - ST Fast Sequence Mode (FSM) Serial Flash Controller
 *
 * Author: Angus Clark <angus.clark@st.com>
 *
 * Copyright (C) 2010-2014 STMicroelectronics Limited
 *
 * JEDEC probe based on drivers/mtd/devices/m25p80.c
 *
 * This code is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 */
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/regmap.h>
#include <linux/platform_device.h>
#include <linux/mfd/syscon.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/spi-nor.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/clk.h>

#include "serial_flash_cmds.h"

/*
 * FSM SPI Controller Registers
 */
#define SPI_CLOCKDIV                    0x0010
#define SPI_MODESELECT                  0x0018
#define SPI_CONFIGDATA                  0x0020
#define SPI_STA_MODE_CHANGE             0x0028
#define SPI_FAST_SEQ_TRANSFER_SIZE      0x0100
#define SPI_FAST_SEQ_ADD1               0x0104
#define SPI_FAST_SEQ_ADD2               0x0108
#define SPI_FAST_SEQ_ADD_CFG            0x010c
#define SPI_FAST_SEQ_OPC1               0x0110
#define SPI_FAST_SEQ_OPC2               0x0114
#define SPI_FAST_SEQ_OPC3               0x0118
#define SPI_FAST_SEQ_OPC4               0x011c
#define SPI_FAST_SEQ_OPC5               0x0120
#define SPI_MODE_BITS                   0x0124
#define SPI_DUMMY_BITS                  0x0128
#define SPI_FAST_SEQ_FLASH_STA_DATA     0x012c
#define SPI_FAST_SEQ_1                  0x0130
#define SPI_FAST_SEQ_2                  0x0134
#define SPI_FAST_SEQ_3                  0x0138
#define SPI_FAST_SEQ_4                  0x013c
#define SPI_FAST_SEQ_CFG                0x0140
#define SPI_FAST_SEQ_STA                0x0144
#define SPI_QUAD_BOOT_SEQ_INIT_1        0x0148
#define SPI_QUAD_BOOT_SEQ_INIT_2        0x014c
#define SPI_QUAD_BOOT_READ_SEQ_1        0x0150
#define SPI_QUAD_BOOT_READ_SEQ_2        0x0154
#define SPI_PROGRAM_ERASE_TIME          0x0158
#define SPI_MULT_PAGE_REPEAT_SEQ_1      0x015c
#define SPI_MULT_PAGE_REPEAT_SEQ_2      0x0160
#define SPI_STATUS_WR_TIME_REG          0x0164
#define SPI_FAST_SEQ_DATA_REG           0x0300

/*
 * Register: SPI_MODESELECT
 */
#define SPI_MODESELECT_CONTIG           0x01
#define SPI_MODESELECT_FASTREAD         0x02
#define SPI_MODESELECT_DUALIO           0x04
#define SPI_MODESELECT_FSM              0x08
#define SPI_MODESELECT_QUADBOOT         0x10

/*
 * Register: SPI_CONFIGDATA
 */
#define SPI_CFG_DEVICE_ST               0x1
#define SPI_CFG_DEVICE_ATMEL            0x4
#define SPI_CFG_MIN_CS_HIGH(x)          (((x) & 0xfff) << 4)
#define SPI_CFG_CS_SETUPHOLD(x)         (((x) & 0xff) << 16)
#define SPI_CFG_DATA_HOLD(x)            (((x) & 0xff) << 24)

#define SPI_CFG_DEFAULT_MIN_CS_HIGH    SPI_CFG_MIN_CS_HIGH(0x0AA)
#define SPI_CFG_DEFAULT_CS_SETUPHOLD   SPI_CFG_CS_SETUPHOLD(0xA0)
#define SPI_CFG_DEFAULT_DATA_HOLD      SPI_CFG_DATA_HOLD(0x00)

/*
 * Register: SPI_FAST_SEQ_TRANSFER_SIZE
 */
#define TRANSFER_SIZE(x)                ((x) * 8)

/*
 * Register: SPI_FAST_SEQ_ADD_CFG
 */
#define ADR_CFG_CYCLES_ADD1(x)          ((x) << 0)
#define ADR_CFG_PADS_1_ADD1             (0x0 << 6)
#define ADR_CFG_PADS_2_ADD1             (0x1 << 6)
#define ADR_CFG_PADS_4_ADD1             (0x3 << 6)
#define ADR_CFG_CSDEASSERT_ADD1         (1   << 8)
#define ADR_CFG_CYCLES_ADD2(x)          ((x) << (0+16))
#define ADR_CFG_PADS_1_ADD2             (0x0 << (6+16))
#define ADR_CFG_PADS_2_ADD2             (0x1 << (6+16))
#define ADR_CFG_PADS_4_ADD2             (0x3 << (6+16))
#define ADR_CFG_CSDEASSERT_ADD2         (1   << (8+16))

/*
 * Register: SPI_FAST_SEQ_n
 */
#define SEQ_OPC_OPCODE(x)               ((x) << 0)
#define SEQ_OPC_CYCLES(x)               ((x) << 8)
#define SEQ_OPC_PADS_1                  (0x0 << 14)
#define SEQ_OPC_PADS_2                  (0x1 << 14)
#define SEQ_OPC_PADS_4                  (0x3 << 14)
#define SEQ_OPC_CSDEASSERT              (1   << 16)

/*
 * Register: SPI_FAST_SEQ_CFG
 */
#define SEQ_CFG_STARTSEQ                (1 << 0)
#define SEQ_CFG_SWRESET                 (1 << 5)
#define SEQ_CFG_CSDEASSERT              (1 << 6)
#define SEQ_CFG_READNOTWRITE            (1 << 7)
#define SEQ_CFG_ERASE                   (1 << 8)
#define SEQ_CFG_PADS_1                  (0x0 << 16)
#define SEQ_CFG_PADS_2                  (0x1 << 16)
#define SEQ_CFG_PADS_4                  (0x3 << 16)

/*
 * Register: SPI_MODE_BITS
 */
#define MODE_DATA(x)                    (x & 0xff)
#define MODE_CYCLES(x)                  ((x & 0x3f) << 16)
#define MODE_PADS_1                     (0x0 << 22)
#define MODE_PADS_2                     (0x1 << 22)
#define MODE_PADS_4                     (0x3 << 22)
#define DUMMY_CSDEASSERT                (1   << 24)

/*
 * Register: SPI_DUMMY_BITS
 */
#define DUMMY_CYCLES(x)                 ((x & 0x3f) << 16)
#define DUMMY_PADS_1                    (0x0 << 22)
#define DUMMY_PADS_2                    (0x1 << 22)
#define DUMMY_PADS_4                    (0x3 << 22)
#define DUMMY_CSDEASSERT                (1   << 24)

/*
 * Register: SPI_FAST_SEQ_FLASH_STA_DATA
 */
#define STA_DATA_BYTE1(x)               ((x & 0xff) << 0)
#define STA_DATA_BYTE2(x)               ((x & 0xff) << 8)
#define STA_PADS_1                      (0x0 << 16)
#define STA_PADS_2                      (0x1 << 16)
#define STA_PADS_4                      (0x3 << 16)
#define STA_CSDEASSERT                  (0x1 << 20)
#define STA_RDNOTWR                     (0x1 << 21)

/*
 * FSM SPI Instruction Opcodes
 */
#define STFSM_OPC_CMD                   0x1
#define STFSM_OPC_ADD                   0x2
#define STFSM_OPC_STA                   0x3
#define STFSM_OPC_MODE                  0x4
#define STFSM_OPC_DUMMY         0x5
#define STFSM_OPC_DATA                  0x6
#define STFSM_OPC_WAIT                  0x7
#define STFSM_OPC_JUMP                  0x8
#define STFSM_OPC_GOTO                  0x9
#define STFSM_OPC_STOP                  0xF

/*
 * FSM SPI Instructions (== opcode + operand).
 */
#define STFSM_INSTR(cmd, op)            ((cmd) | ((op) << 4))

#define STFSM_INST_CMD1                 STFSM_INSTR(STFSM_OPC_CMD,      1)
#define STFSM_INST_CMD2                 STFSM_INSTR(STFSM_OPC_CMD,      2)
#define STFSM_INST_CMD3                 STFSM_INSTR(STFSM_OPC_CMD,      3)
#define STFSM_INST_CMD4                 STFSM_INSTR(STFSM_OPC_CMD,      4)
#define STFSM_INST_CMD5                 STFSM_INSTR(STFSM_OPC_CMD,      5)
#define STFSM_INST_ADD1                 STFSM_INSTR(STFSM_OPC_ADD,      1)
#define STFSM_INST_ADD2                 STFSM_INSTR(STFSM_OPC_ADD,      2)

#define STFSM_INST_DATA_WRITE           STFSM_INSTR(STFSM_OPC_DATA,     1)
#define STFSM_INST_DATA_READ            STFSM_INSTR(STFSM_OPC_DATA,     2)

#define STFSM_INST_STA_RD1              STFSM_INSTR(STFSM_OPC_STA,      0x1)
#define STFSM_INST_STA_WR1              STFSM_INSTR(STFSM_OPC_STA,      0x1)
#define STFSM_INST_STA_RD2              STFSM_INSTR(STFSM_OPC_STA,      0x2)
#define STFSM_INST_STA_WR1_2            STFSM_INSTR(STFSM_OPC_STA,      0x3)

#define STFSM_INST_MODE                 STFSM_INSTR(STFSM_OPC_MODE,     0)
#define STFSM_INST_DUMMY                STFSM_INSTR(STFSM_OPC_DUMMY,    0)
#define STFSM_INST_WAIT                 STFSM_INSTR(STFSM_OPC_WAIT,     0)
#define STFSM_INST_STOP                 STFSM_INSTR(STFSM_OPC_STOP,     0)

#define STFSM_DEFAULT_EMI_FREQ 100000000UL                        /* 100 MHz */
#define STFSM_DEFAULT_WR_TIME  (STFSM_DEFAULT_EMI_FREQ * (15/1000)) /* 15ms */

#define STFSM_FLASH_SAFE_FREQ  10000000UL                         /* 10 MHz */

#define STFSM_MAX_WAIT_SEQ_MS  1000     /* FSM execution time */

/* S25FLxxxS commands */
#define S25FL_CMD_WRITE4_1_1_4 0x34
#define S25FL_CMD_SE4          0xdc
#define S25FL_CMD_CLSR         0x30
#define S25FL_CMD_DYBWR                0xe1
#define S25FL_CMD_DYBRD                0xe0
#define S25FL_CMD_WRITE4       0x12    /* Note, opcode clashes with
                                        * 'SPINOR_OP_WRITE_1_4_4'
                                        * as found on N25Qxxx devices! */

/* Status register */
#define FLASH_STATUS_BUSY      0x01
#define FLASH_STATUS_WEL       0x02
#define FLASH_STATUS_BP0       0x04
#define FLASH_STATUS_BP1       0x08
#define FLASH_STATUS_BP2       0x10
#define FLASH_STATUS_SRWP0     0x80
#define FLASH_STATUS_TIMEOUT   0xff
/* S25FL Error Flags */
#define S25FL_STATUS_E_ERR     0x20
#define S25FL_STATUS_P_ERR     0x40

#define N25Q_CMD_WRVCR         0x81
#define N25Q_CMD_RDVCR         0x85
#define N25Q_CMD_RDVECR        0x65
#define N25Q_CMD_RDNVCR        0xb5
#define N25Q_CMD_WRNVCR        0xb1

#define FLASH_PAGESIZE         256                      /* In Bytes    */
#define FLASH_PAGESIZE_32      (FLASH_PAGESIZE / 4)     /* In uint32_t */
#define FLASH_MAX_BUSY_WAIT    (300 * HZ)       /* Maximum 'CHIPERASE' time */

/*
 * Flags to tweak operation of default read/write/erase routines
 */
#define CFG_READ_TOGGLE_32BIT_ADDR     0x00000001
#define CFG_WRITE_TOGGLE_32BIT_ADDR    0x00000002
#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008
#define CFG_S25FL_CHECK_ERROR_FLAGS    0x00000010

struct stfsm_seq {
        uint32_t data_size;
        uint32_t addr1;
        uint32_t addr2;
        uint32_t addr_cfg;
        uint32_t seq_opc[5];
        uint32_t mode;
        uint32_t dummy;
        uint32_t status;
        uint8_t  seq[16];
        uint32_t seq_cfg;
} __packed __aligned(4);

struct stfsm {
        struct device           *dev;
        void __iomem            *base;
        struct resource         *region;
        struct mtd_info         mtd;
        struct mutex            lock;
        struct flash_info       *info;
        struct clk              *clk;

        uint32_t                configuration;
        uint32_t                fifo_dir_delay;
        bool                    booted_from_spi;
        bool                    reset_signal;
        bool                    reset_por;

        struct stfsm_seq stfsm_seq_read;
        struct stfsm_seq stfsm_seq_write;
        struct stfsm_seq stfsm_seq_en_32bit_addr;
};

/* Parameters to configure a READ or WRITE FSM sequence */
struct seq_rw_config {
        uint32_t        flags;          /* flags to support config */
        uint8_t         cmd;            /* FLASH command */
        int             write;          /* Write Sequence */
        uint8_t         addr_pads;      /* No. of addr pads (MODE & DUMMY) */
        uint8_t         data_pads;      /* No. of data pads */
        uint8_t         mode_data;      /* MODE data */
        uint8_t         mode_cycles;    /* No. of MODE cycles */
        uint8_t         dummy_cycles;   /* No. of DUMMY cycles */
};

/* SPI Flash Device Table */
struct flash_info {
        char            *name;
        /*
         * JEDEC id zero means "no ID" (most older chips); otherwise it has
         * a high byte of zero plus three data bytes: the manufacturer id,
         * then a two byte device id.
         */
        u32             jedec_id;
        u16             ext_id;
        /*
         * The size listed here is what works with SPINOR_OP_SE, which isn't
         * necessarily called a "sector" by the vendor.
         */
        unsigned        sector_size;
        u16             n_sectors;
        u32             flags;
        /*
         * Note, where FAST_READ is supported, freq_max specifies the
         * FAST_READ frequency, not the READ frequency.
         */
        u32             max_freq;
        int             (*config)(struct stfsm *);
};

static int stfsm_n25q_config(struct stfsm *fsm);
static int stfsm_mx25_config(struct stfsm *fsm);
static int stfsm_s25fl_config(struct stfsm *fsm);
static int stfsm_w25q_config(struct stfsm *fsm);

static struct flash_info flash_types[] = {
        /*
         * ST Microelectronics/Numonyx --
         * (newer production versions may have feature updates
         * (eg faster operating frequency)
         */
#define M25P_FLAG (FLASH_FLAG_READ_WRITE | FLASH_FLAG_READ_FAST)
        { "m25p40",  0x202013, 0,  64 * 1024,   8, M25P_FLAG, 25, NULL },
        { "m25p80",  0x202014, 0,  64 * 1024,  16, M25P_FLAG, 25, NULL },
        { "m25p16",  0x202015, 0,  64 * 1024,  32, M25P_FLAG, 25, NULL },
        { "m25p32",  0x202016, 0,  64 * 1024,  64, M25P_FLAG, 50, NULL },
        { "m25p64",  0x202017, 0,  64 * 1024, 128, M25P_FLAG, 50, NULL },
        { "m25p128", 0x202018, 0, 256 * 1024,  64, M25P_FLAG, 50, NULL },

#define M25PX_FLAG (FLASH_FLAG_READ_WRITE      |        \
                    FLASH_FLAG_READ_FAST        |       \
                    FLASH_FLAG_READ_1_1_2       |       \
                    FLASH_FLAG_WRITE_1_1_2)
        { "m25px32", 0x207116, 0,  64 * 1024,  64, M25PX_FLAG, 75, NULL },
        { "m25px64", 0x207117, 0,  64 * 1024, 128, M25PX_FLAG, 75, NULL },

        /* Macronix MX25xxx
         *     - Support for 'FLASH_FLAG_WRITE_1_4_4' is omitted for devices
         *       where operating frequency must be reduced.
         */
#define MX25_FLAG (FLASH_FLAG_READ_WRITE       |        \
                   FLASH_FLAG_READ_FAST         |       \
                   FLASH_FLAG_READ_1_1_2        |       \
                   FLASH_FLAG_READ_1_2_2        |       \
                   FLASH_FLAG_READ_1_1_4        |       \
                   FLASH_FLAG_SE_4K             |       \
                   FLASH_FLAG_SE_32K)
        { "mx25l3255e",  0xc29e16, 0, 64 * 1024, 64,
          (MX25_FLAG | FLASH_FLAG_WRITE_1_4_4), 86,
          stfsm_mx25_config},
        { "mx25l25635e", 0xc22019, 0, 64*1024, 512,
          (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70,
          stfsm_mx25_config },
        { "mx25l25655e", 0xc22619, 0, 64*1024, 512,
          (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70,
          stfsm_mx25_config},

#define N25Q_FLAG (FLASH_FLAG_READ_WRITE       |        \
                   FLASH_FLAG_READ_FAST         |       \
                   FLASH_FLAG_READ_1_1_2        |       \
                   FLASH_FLAG_READ_1_2_2        |       \
                   FLASH_FLAG_READ_1_1_4        |       \
                   FLASH_FLAG_READ_1_4_4        |       \
                   FLASH_FLAG_WRITE_1_1_2       |       \
                   FLASH_FLAG_WRITE_1_2_2       |       \
                   FLASH_FLAG_WRITE_1_1_4       |       \
                   FLASH_FLAG_WRITE_1_4_4)
        { "n25q128", 0x20ba18, 0, 64 * 1024,  256, N25Q_FLAG, 108,
          stfsm_n25q_config },
        { "n25q256", 0x20ba19, 0, 64 * 1024,  512,
          N25Q_FLAG | FLASH_FLAG_32BIT_ADDR, 108, stfsm_n25q_config },

        /*
         * Spansion S25FLxxxP
         *     - 256KiB and 64KiB sector variants (identified by ext. JEDEC)
         */
#define S25FLXXXP_FLAG (FLASH_FLAG_READ_WRITE  |        \
                        FLASH_FLAG_READ_1_1_2   |       \
                        FLASH_FLAG_READ_1_2_2   |       \
                        FLASH_FLAG_READ_1_1_4   |       \
                        FLASH_FLAG_READ_1_4_4   |       \
                        FLASH_FLAG_WRITE_1_1_4  |       \
                        FLASH_FLAG_READ_FAST)
        { "s25fl032p",  0x010215, 0x4d00,  64 * 1024,  64, S25FLXXXP_FLAG, 80,
          stfsm_s25fl_config},
        { "s25fl129p0", 0x012018, 0x4d00, 256 * 1024,  64, S25FLXXXP_FLAG, 80,
          stfsm_s25fl_config },
        { "s25fl129p1", 0x012018, 0x4d01,  64 * 1024, 256, S25FLXXXP_FLAG, 80,
          stfsm_s25fl_config },

        /*
         * Spansion S25FLxxxS
         *     - 256KiB and 64KiB sector variants (identified by ext. JEDEC)
         *     - RESET# signal supported by die but not bristled out on all
         *       package types.  The package type is a function of board design,
         *       so this information is captured in the board's flags.
         *     - Supports 'DYB' sector protection. Depending on variant, sectors
         *       may default to locked state on power-on.
         */
#define S25FLXXXS_FLAG (S25FLXXXP_FLAG         |        \
                        FLASH_FLAG_RESET        |       \
                        FLASH_FLAG_DYB_LOCKING)
        { "s25fl128s0", 0x012018, 0x0300,  256 * 1024, 64, S25FLXXXS_FLAG, 80,
          stfsm_s25fl_config },
        { "s25fl128s1", 0x012018, 0x0301,  64 * 1024, 256, S25FLXXXS_FLAG, 80,
          stfsm_s25fl_config },
        { "s25fl256s0", 0x010219, 0x4d00, 256 * 1024, 128,
          S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config },
        { "s25fl256s1", 0x010219, 0x4d01,  64 * 1024, 512,
          S25FLXXXS_FLAG | FLASH_FLAG_32BIT_ADDR, 80, stfsm_s25fl_config },

        /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
#define W25X_FLAG (FLASH_FLAG_READ_WRITE       |        \
                   FLASH_FLAG_READ_FAST         |       \
                   FLASH_FLAG_READ_1_1_2        |       \
                   FLASH_FLAG_WRITE_1_1_2)
        { "w25x40",  0xef3013, 0,  64 * 1024,   8, W25X_FLAG, 75, NULL },
        { "w25x80",  0xef3014, 0,  64 * 1024,  16, W25X_FLAG, 75, NULL },
        { "w25x16",  0xef3015, 0,  64 * 1024,  32, W25X_FLAG, 75, NULL },
        { "w25x32",  0xef3016, 0,  64 * 1024,  64, W25X_FLAG, 75, NULL },
        { "w25x64",  0xef3017, 0,  64 * 1024, 128, W25X_FLAG, 75, NULL },

        /* Winbond -- w25q "blocks" are 64K, "sectors" are 4KiB */
#define W25Q_FLAG (FLASH_FLAG_READ_WRITE       |        \
                   FLASH_FLAG_READ_FAST         |       \
                   FLASH_FLAG_READ_1_1_2        |       \
                   FLASH_FLAG_READ_1_2_2        |       \
                   FLASH_FLAG_READ_1_1_4        |       \
                   FLASH_FLAG_READ_1_4_4        |       \
                   FLASH_FLAG_WRITE_1_1_4)
        { "w25q80",  0xef4014, 0,  64 * 1024,  16, W25Q_FLAG, 80,
          stfsm_w25q_config },
        { "w25q16",  0xef4015, 0,  64 * 1024,  32, W25Q_FLAG, 80,
          stfsm_w25q_config },
        { "w25q32",  0xef4016, 0,  64 * 1024,  64, W25Q_FLAG, 80,
          stfsm_w25q_config },
        { "w25q64",  0xef4017, 0,  64 * 1024, 128, W25Q_FLAG, 80,
          stfsm_w25q_config },

        /* Sentinel */
        { NULL, 0x000000, 0, 0, 0, 0, 0, NULL },
};

/*
 * FSM message sequence configurations:
 *
 * All configs are presented in order of preference
 */

/* Default READ configurations, in order of preference */
static struct seq_rw_config default_read_configs[] = {
        {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4,   0, 4, 4, 0x00, 2, 4},
        {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4,   0, 1, 4, 0x00, 4, 0},
        {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2,   0, 2, 2, 0x00, 4, 0},
        {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2,   0, 1, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_FAST,  SPINOR_OP_READ_FAST,    0, 1, 1, 0x00, 0, 8},
        {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ,         0, 1, 1, 0x00, 0, 0},
        {0x00,                  0,                      0, 0, 0, 0x00, 0, 0},
};

/* Default WRITE configurations */
static struct seq_rw_config default_write_configs[] = {
        {FLASH_FLAG_WRITE_1_4_4, SPINOR_OP_WRITE_1_4_4, 1, 4, 4, 0x00, 0, 0},
        {FLASH_FLAG_WRITE_1_1_4, SPINOR_OP_WRITE_1_1_4, 1, 1, 4, 0x00, 0, 0},
        {FLASH_FLAG_WRITE_1_2_2, SPINOR_OP_WRITE_1_2_2, 1, 2, 2, 0x00, 0, 0},
        {FLASH_FLAG_WRITE_1_1_2, SPINOR_OP_WRITE_1_1_2, 1, 1, 2, 0x00, 0, 0},
        {FLASH_FLAG_READ_WRITE,  SPINOR_OP_WRITE,       1, 1, 1, 0x00, 0, 0},
        {0x00,                   0,                     0, 0, 0, 0x00, 0, 0},
};

/*
 * [N25Qxxx] Configuration
 */
#define N25Q_VCR_DUMMY_CYCLES(x)        (((x) & 0xf) << 4)
#define N25Q_VCR_XIP_DISABLED           ((uint8_t)0x1 << 3)
#define N25Q_VCR_WRAP_CONT              0x3

/* N25Q 3-byte Address READ configurations
 *      - 'FAST' variants configured for 8 dummy cycles.
 *
 * Note, the number of dummy cycles used for 'FAST' READ operations is
 * configurable and would normally be tuned according to the READ command and
 * operating frequency.  However, this applies universally to all 'FAST' READ
 * commands, including those used by the SPIBoot controller, and remains in
 * force until the device is power-cycled.  Since the SPIBoot controller is
 * hard-wired to use 8 dummy cycles, we must configure the device to also use 8
 * cycles.
 */
static struct seq_rw_config n25q_read3_configs[] = {
        {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4,   0, 4, 4, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4,   0, 1, 4, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2,   0, 2, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2,   0, 1, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_FAST,  SPINOR_OP_READ_FAST,    0, 1, 1, 0x00, 0, 8},
        {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ,         0, 1, 1, 0x00, 0, 0},
        {0x00,                  0,                      0, 0, 0, 0x00, 0, 0},
};

/* N25Q 4-byte Address READ configurations
 *      - use special 4-byte address READ commands (reduces overheads, and
 *        reduces risk of hitting watchdog reset issues).
 *      - 'FAST' variants configured for 8 dummy cycles (see note above.)
 */
static struct seq_rw_config n25q_read4_configs[] = {
        {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_FAST,  SPINOR_OP_READ_FAST_4B,  0, 1, 1, 0x00, 0, 8},
        {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B,       0, 1, 1, 0x00, 0, 0},
        {0x00,                  0,                       0, 0, 0, 0x00, 0, 0},
};

/*
 * [MX25xxx] Configuration
 */
#define MX25_STATUS_QE                  (0x1 << 6)

static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq)
{
        seq->seq_opc[0] = (SEQ_OPC_PADS_1 |
                           SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(SPINOR_OP_EN4B) |
                           SEQ_OPC_CSDEASSERT);

        seq->seq[0] = STFSM_INST_CMD1;
        seq->seq[1] = STFSM_INST_WAIT;
        seq->seq[2] = STFSM_INST_STOP;

        seq->seq_cfg = (SEQ_CFG_PADS_1 |
                        SEQ_CFG_ERASE |
                        SEQ_CFG_READNOTWRITE |
                        SEQ_CFG_CSDEASSERT |
                        SEQ_CFG_STARTSEQ);

        return 0;
}

/*
 * [S25FLxxx] Configuration
 */
#define STFSM_S25FL_CONFIG_QE           (0x1 << 1)

/*
 * S25FLxxxS devices provide three ways of supporting 32-bit addressing: Bank
 * Register, Extended Address Modes, and a 32-bit address command set.  The
 * 32-bit address command set is used here, since it avoids any problems with
 * entering a state that is incompatible with the SPIBoot Controller.
 */
static struct seq_rw_config stfsm_s25fl_read4_configs[] = {
        {FLASH_FLAG_READ_1_4_4,  SPINOR_OP_READ_1_4_4_4B,  0, 4, 4, 0x00, 2, 4},
        {FLASH_FLAG_READ_1_1_4,  SPINOR_OP_READ_1_1_4_4B,  0, 1, 4, 0x00, 0, 8},
        {FLASH_FLAG_READ_1_2_2,  SPINOR_OP_READ_1_2_2_4B,  0, 2, 2, 0x00, 4, 0},
        {FLASH_FLAG_READ_1_1_2,  SPINOR_OP_READ_1_1_2_4B,  0, 1, 2, 0x00, 0, 8},
        {FLASH_FLAG_READ_FAST,   SPINOR_OP_READ_FAST_4B,   0, 1, 1, 0x00, 0, 8},
        {FLASH_FLAG_READ_WRITE,  SPINOR_OP_READ_4B,        0, 1, 1, 0x00, 0, 0},
        {0x00,                   0,                        0, 0, 0, 0x00, 0, 0},
};

static struct seq_rw_config stfsm_s25fl_write4_configs[] = {
        {FLASH_FLAG_WRITE_1_1_4, S25FL_CMD_WRITE4_1_1_4, 1, 1, 4, 0x00, 0, 0},
        {FLASH_FLAG_READ_WRITE,  S25FL_CMD_WRITE4,       1, 1, 1, 0x00, 0, 0},
        {0x00,                   0,                      0, 0, 0, 0x00, 0, 0},
};

/*
 * [W25Qxxx] Configuration
 */
#define W25Q_STATUS_QE                  (0x1 << 1)

static struct stfsm_seq stfsm_seq_read_jedec = {
        .data_size = TRANSFER_SIZE(8),
        .seq_opc[0] = (SEQ_OPC_PADS_1 |
                       SEQ_OPC_CYCLES(8) |
                       SEQ_OPC_OPCODE(SPINOR_OP_RDID)),
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_DATA_READ,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

static struct stfsm_seq stfsm_seq_read_status_fifo = {
        .data_size = TRANSFER_SIZE(4),
        .seq_opc[0] = (SEQ_OPC_PADS_1 |
                       SEQ_OPC_CYCLES(8) |
                       SEQ_OPC_OPCODE(SPINOR_OP_RDSR)),
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_DATA_READ,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

static struct stfsm_seq stfsm_seq_erase_sector = {
        /* 'addr_cfg' configured during initialisation */
        .seq_opc = {
                (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                 SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT),

                (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                 SEQ_OPC_OPCODE(SPINOR_OP_SE)),
        },
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_CMD2,
                STFSM_INST_ADD1,
                STFSM_INST_ADD2,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

static struct stfsm_seq stfsm_seq_erase_chip = {
        .seq_opc = {
                (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                 SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT),

                (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                 SEQ_OPC_OPCODE(SPINOR_OP_CHIP_ERASE) | SEQ_OPC_CSDEASSERT),
        },
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_CMD2,
                STFSM_INST_WAIT,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_ERASE |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

static struct stfsm_seq stfsm_seq_write_status = {
        .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                       SEQ_OPC_OPCODE(SPINOR_OP_WREN) | SEQ_OPC_CSDEASSERT),
        .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                       SEQ_OPC_OPCODE(SPINOR_OP_WRSR)),
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_CMD2,
                STFSM_INST_STA_WR1,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

/* Dummy sequence to read one byte of data from flash into the FIFO */
static const struct stfsm_seq stfsm_seq_load_fifo_byte = {
        .data_size = TRANSFER_SIZE(1),
        .seq_opc[0] = (SEQ_OPC_PADS_1 |
                       SEQ_OPC_CYCLES(8) |
                       SEQ_OPC_OPCODE(SPINOR_OP_RDID)),
        .seq = {
                STFSM_INST_CMD1,
                STFSM_INST_DATA_READ,
                STFSM_INST_STOP,
        },
        .seq_cfg = (SEQ_CFG_PADS_1 |
                    SEQ_CFG_READNOTWRITE |
                    SEQ_CFG_CSDEASSERT |
                    SEQ_CFG_STARTSEQ),
};

static int stfsm_n25q_en_32bit_addr_seq(struct stfsm_seq *seq)
{
        seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(SPINOR_OP_EN4B));
        seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(SPINOR_OP_WREN) |
                           SEQ_OPC_CSDEASSERT);

        seq->seq[0] = STFSM_INST_CMD2;
        seq->seq[1] = STFSM_INST_CMD1;
        seq->seq[2] = STFSM_INST_WAIT;
        seq->seq[3] = STFSM_INST_STOP;

        seq->seq_cfg = (SEQ_CFG_PADS_1 |
                        SEQ_CFG_ERASE |
                        SEQ_CFG_READNOTWRITE |
                        SEQ_CFG_CSDEASSERT |
                        SEQ_CFG_STARTSEQ);

        return 0;
}

static inline int stfsm_is_idle(struct stfsm *fsm)
{
        return readl(fsm->base + SPI_FAST_SEQ_STA) & 0x10;
}

static inline uint32_t stfsm_fifo_available(struct stfsm *fsm)
{
        return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f;
}

static inline void stfsm_load_seq(struct stfsm *fsm,
                                  const struct stfsm_seq *seq)
{
        void __iomem *dst = fsm->base + SPI_FAST_SEQ_TRANSFER_SIZE;
        const uint32_t *src = (const uint32_t *)seq;
        int words = sizeof(*seq) / sizeof(*src);

        BUG_ON(!stfsm_is_idle(fsm));

        while (words--) {
                writel(*src, dst);
                src++;
                dst += 4;
        }
}

static void stfsm_wait_seq(struct stfsm *fsm)
{
        unsigned long deadline;
        int timeout = 0;

        deadline = jiffies + msecs_to_jiffies(STFSM_MAX_WAIT_SEQ_MS);

        while (!timeout) {
                if (time_after_eq(jiffies, deadline))
                        timeout = 1;

                if (stfsm_is_idle(fsm))
                        return;

                cond_resched();
        }

        dev_err(fsm->dev, "timeout on sequence completion\n");
}

static void stfsm_read_fifo(struct stfsm *fsm, uint32_t *buf, uint32_t size)
{
        uint32_t remaining = size >> 2;
        uint32_t avail;
        uint32_t words;

        dev_dbg(fsm->dev, "Reading %d bytes from FIFO\n", size);

        BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3));

        while (remaining) {
                for (;;) {
                        avail = stfsm_fifo_available(fsm);
                        if (avail)
                                break;
                        udelay(1);
                }
                words = min(avail, remaining);
                remaining -= words;

                readsl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words);
                buf += words;
        }
}

/*
 * Clear the data FIFO
 *
 * Typically, this is only required during driver initialisation, where no
 * assumptions can be made regarding the state of the FIFO.
 *
 * The process of clearing the FIFO is complicated by fact that while it is
 * possible for the FIFO to contain an arbitrary number of bytes [1], the
 * SPI_FAST_SEQ_STA register only reports the number of complete 32-bit words
 * present.  Furthermore, data can only be drained from the FIFO by reading
 * complete 32-bit words.
 *
 * With this in mind, a two stage process is used to the clear the FIFO:
 *
 *     1. Read any complete 32-bit words from the FIFO, as reported by the
 *        SPI_FAST_SEQ_STA register.
 *
 *     2. Mop up any remaining bytes.  At this point, it is not known if there
 *        are 0, 1, 2, or 3 bytes in the FIFO.  To handle all cases, a dummy FSM
 *        sequence is used to load one byte at a time, until a complete 32-bit
 *        word is formed; at most, 4 bytes will need to be loaded.
 *
 * [1] It is theoretically possible for the FIFO to contain an arbitrary number
 *     of bits.  However, since there are no known use-cases that leave
 *     incomplete bytes in the FIFO, only words and bytes are considered here.
 */
static void stfsm_clear_fifo(struct stfsm *fsm)
{
        const struct stfsm_seq *seq = &stfsm_seq_load_fifo_byte;
        uint32_t words, i;

        /* 1. Clear any 32-bit words */
        words = stfsm_fifo_available(fsm);
        if (words) {
                for (i = 0; i < words; i++)
                        readl(fsm->base + SPI_FAST_SEQ_DATA_REG);
                dev_dbg(fsm->dev, "cleared %d words from FIFO\n", words);
        }

        /*
         * 2. Clear any remaining bytes
         *    - Load the FIFO, one byte at a time, until a complete 32-bit word
         *      is available.
         */
        for (i = 0, words = 0; i < 4 && !words; i++) {
                stfsm_load_seq(fsm, seq);
                stfsm_wait_seq(fsm);
                words = stfsm_fifo_available(fsm);
        }

        /*    - A single word must be available now */
        if (words != 1) {
                dev_err(fsm->dev, "failed to clear bytes from the data FIFO\n");
                return;
        }

        /*    - Read the 32-bit word */
        readl(fsm->base + SPI_FAST_SEQ_DATA_REG);

        dev_dbg(fsm->dev, "cleared %d byte(s) from the data FIFO\n", 4 - i);
}

static int stfsm_write_fifo(struct stfsm *fsm, const uint32_t *buf,
                            uint32_t size)
{
        uint32_t words = size >> 2;

        dev_dbg(fsm->dev, "writing %d bytes to FIFO\n", size);

        BUG_ON((((uintptr_t)buf) & 0x3) || (size & 0x3));

        writesl(fsm->base + SPI_FAST_SEQ_DATA_REG, buf, words);

        return size;
}

static int stfsm_enter_32bit_addr(struct stfsm *fsm, int enter)
{
        struct stfsm_seq *seq = &fsm->stfsm_seq_en_32bit_addr;
        uint32_t cmd = enter ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;

        seq->seq_opc[0] = (SEQ_OPC_PADS_1 |
                           SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(cmd) |
                           SEQ_OPC_CSDEASSERT);

        stfsm_load_seq(fsm, seq);

        stfsm_wait_seq(fsm);

        return 0;
}

static uint8_t stfsm_wait_busy(struct stfsm *fsm)
{
        struct stfsm_seq *seq = &stfsm_seq_read_status_fifo;
        unsigned long deadline;
        uint32_t status;
        int timeout = 0;

        /* Use RDRS1 */
        seq->seq_opc[0] = (SEQ_OPC_PADS_1 |
                           SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(SPINOR_OP_RDSR));

        /* Load read_status sequence */
        stfsm_load_seq(fsm, seq);

        /*
         * Repeat until busy bit is deasserted, or timeout, or error (S25FLxxxS)
         */
        deadline = jiffies + FLASH_MAX_BUSY_WAIT;
        while (!timeout) {
                if (time_after_eq(jiffies, deadline))
                        timeout = 1;

                stfsm_wait_seq(fsm);

                stfsm_read_fifo(fsm, &status, 4);

                if ((status & FLASH_STATUS_BUSY) == 0)
                        return 0;

                if ((fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS) &&
                    ((status & S25FL_STATUS_P_ERR) ||
                     (status & S25FL_STATUS_E_ERR)))
                        return (uint8_t)(status & 0xff);

                if (!timeout)
                        /* Restart */
                        writel(seq->seq_cfg, fsm->base + SPI_FAST_SEQ_CFG);

                cond_resched();
        }

        dev_err(fsm->dev, "timeout on wait_busy\n");

        return FLASH_STATUS_TIMEOUT;
}

static int stfsm_read_status(struct stfsm *fsm, uint8_t cmd,
                             uint8_t *data, int bytes)
{
        struct stfsm_seq *seq = &stfsm_seq_read_status_fifo;
        uint32_t tmp;
        uint8_t *t = (uint8_t *)&tmp;
        int i;

        dev_dbg(fsm->dev, "read 'status' register [0x%02x], %d byte(s)\n",
                cmd, bytes);

        BUG_ON(bytes != 1 && bytes != 2);

        seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(cmd)),

        stfsm_load_seq(fsm, seq);

        stfsm_read_fifo(fsm, &tmp, 4);

        for (i = 0; i < bytes; i++)
                data[i] = t[i];

        stfsm_wait_seq(fsm);

        return 0;
}

static int stfsm_write_status(struct stfsm *fsm, uint8_t cmd,
                            uint16_t data, int bytes, int wait_busy)
{
        struct stfsm_seq *seq = &stfsm_seq_write_status;

        dev_dbg(fsm->dev,
                "write 'status' register [0x%02x], %d byte(s), 0x%04x\n"
                " %s wait-busy\n", cmd, bytes, data, wait_busy ? "with" : "no");

        BUG_ON(bytes != 1 && bytes != 2);

        seq->seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(cmd));

        seq->status = (uint32_t)data | STA_PADS_1 | STA_CSDEASSERT;
        seq->seq[2] = (bytes == 1) ? STFSM_INST_STA_WR1 : STFSM_INST_STA_WR1_2;

        stfsm_load_seq(fsm, seq);

        stfsm_wait_seq(fsm);

        if (wait_busy)
                stfsm_wait_busy(fsm);

        return 0;
}

/*
 * SoC reset on 'boot-from-spi' systems
 *
 * Certain modes of operation cause the Flash device to enter a particular state
 * for a period of time (e.g. 'Erase Sector', 'Quad Enable', and 'Enter 32-bit
 * Addr' commands).  On boot-from-spi systems, it is important to consider what
 * happens if a warm reset occurs during this period.  The SPIBoot controller
 * assumes that Flash device is in its default reset state, 24-bit address mode,
 * and ready to accept commands.  This can be achieved using some form of
 * on-board logic/controller to force a device POR in response to a SoC-level
 * reset or by making use of the device reset signal if available (limited
 * number of devices only).
 *
 * Failure to take such precautions can cause problems following a warm reset.
 * For some operations (e.g. ERASE), there is little that can be done.  For
 * other modes of operation (e.g. 32-bit addressing), options are often
 * available that can help minimise the window in which a reset could cause a
 * problem.
 *
 */
static bool stfsm_can_handle_soc_reset(struct stfsm *fsm)
{
        /* Reset signal is available on the board and supported by the device */
        if (fsm->reset_signal && fsm->info->flags & FLASH_FLAG_RESET)
                return true;

        /* Board-level logic forces a power-on-reset */
        if (fsm->reset_por)

                return true;

        /* Reset is not properly handled and may result in failure to reboot */
        return false;
}

/* Configure 'addr_cfg' according to addressing mode */
static void stfsm_prepare_erasesec_seq(struct stfsm *fsm,
                                       struct stfsm_seq *seq)
{
        int addr1_cycles = fsm->info->flags & FLASH_FLAG_32BIT_ADDR ? 16 : 8;

        seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(addr1_cycles) |
                         ADR_CFG_PADS_1_ADD1 |
                         ADR_CFG_CYCLES_ADD2(16) |
                         ADR_CFG_PADS_1_ADD2 |
                         ADR_CFG_CSDEASSERT_ADD2);
}

/* Search for preferred configuration based on available flags */
static struct seq_rw_config *
stfsm_search_seq_rw_configs(struct stfsm *fsm,
                            struct seq_rw_config cfgs[])
{
        struct seq_rw_config *config;
        int flags = fsm->info->flags;

        for (config = cfgs; config->cmd != 0; config++)
                if ((config->flags & flags) == config->flags)
                        return config;

        return NULL;
}

/* Prepare a READ/WRITE sequence according to configuration parameters */
static void stfsm_prepare_rw_seq(struct stfsm *fsm,
                                 struct stfsm_seq *seq,
                                 struct seq_rw_config *cfg)
{
        int addr1_cycles, addr2_cycles;
        int i = 0;

        memset(seq, 0, sizeof(*seq));

        /* Add READ/WRITE OPC  */
        seq->seq_opc[i++] = (SEQ_OPC_PADS_1 |
                             SEQ_OPC_CYCLES(8) |
                             SEQ_OPC_OPCODE(cfg->cmd));

        /* Add WREN OPC for a WRITE sequence */
        if (cfg->write)
                seq->seq_opc[i++] = (SEQ_OPC_PADS_1 |
                                     SEQ_OPC_CYCLES(8) |
                                     SEQ_OPC_OPCODE(SPINOR_OP_WREN) |
                                     SEQ_OPC_CSDEASSERT);

        /* Address configuration (24 or 32-bit addresses) */
        addr1_cycles  = (fsm->info->flags & FLASH_FLAG_32BIT_ADDR) ? 16 : 8;
        addr1_cycles /= cfg->addr_pads;
        addr2_cycles  = 16 / cfg->addr_pads;
        seq->addr_cfg = ((addr1_cycles & 0x3f) << 0 |   /* ADD1 cycles */
                         (cfg->addr_pads - 1) << 6 |    /* ADD1 pads */
                         (addr2_cycles & 0x3f) << 16 |  /* ADD2 cycles */
                         ((cfg->addr_pads - 1) << 22)); /* ADD2 pads */

        /* Data/Sequence configuration */
        seq->seq_cfg = ((cfg->data_pads - 1) << 16 |
                        SEQ_CFG_STARTSEQ |
                        SEQ_CFG_CSDEASSERT);
        if (!cfg->write)
                seq->seq_cfg |= SEQ_CFG_READNOTWRITE;

        /* Mode configuration (no. of pads taken from addr cfg) */
        seq->mode = ((cfg->mode_data & 0xff) << 0 |     /* data */
                     (cfg->mode_cycles & 0x3f) << 16 |  /* cycles */
                     (cfg->addr_pads - 1) << 22);       /* pads */

        /* Dummy configuration (no. of pads taken from addr cfg) */
        seq->dummy = ((cfg->dummy_cycles & 0x3f) << 16 |        /* cycles */
                      (cfg->addr_pads - 1) << 22);              /* pads */


        /* Instruction sequence */
        i = 0;
        if (cfg->write)
                seq->seq[i++] = STFSM_INST_CMD2;

        seq->seq[i++] = STFSM_INST_CMD1;

        seq->seq[i++] = STFSM_INST_ADD1;
        seq->seq[i++] = STFSM_INST_ADD2;

        if (cfg->mode_cycles)
                seq->seq[i++] = STFSM_INST_MODE;

        if (cfg->dummy_cycles)
                seq->seq[i++] = STFSM_INST_DUMMY;

        seq->seq[i++] =
                cfg->write ? STFSM_INST_DATA_WRITE : STFSM_INST_DATA_READ;
        seq->seq[i++] = STFSM_INST_STOP;
}

static int stfsm_search_prepare_rw_seq(struct stfsm *fsm,
                                       struct stfsm_seq *seq,
                                       struct seq_rw_config *cfgs)
{
        struct seq_rw_config *config;

        config = stfsm_search_seq_rw_configs(fsm, cfgs);
        if (!config) {
                dev_err(fsm->dev, "failed to find suitable config\n");
                return -EINVAL;
        }

        stfsm_prepare_rw_seq(fsm, seq, config);

        return 0;
}

/* Prepare a READ/WRITE/ERASE 'default' sequences */
static int stfsm_prepare_rwe_seqs_default(struct stfsm *fsm)
{
        uint32_t flags = fsm->info->flags;
        int ret;

        /* Configure 'READ' sequence */
        ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read,
                                          default_read_configs);
        if (ret) {
                dev_err(fsm->dev,
                        "failed to prep READ sequence with flags [0x%08x]\n",
                        flags);
                return ret;
        }

        /* Configure 'WRITE' sequence */
        ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write,
                                          default_write_configs);
        if (ret) {
                dev_err(fsm->dev,
                        "failed to prep WRITE sequence with flags [0x%08x]\n",
                        flags);
                return ret;
        }

        /* Configure 'ERASE_SECTOR' sequence */
        stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector);

        return 0;
}

static int stfsm_mx25_config(struct stfsm *fsm)
{
        uint32_t flags = fsm->info->flags;
        uint32_t data_pads;
        uint8_t sta;
        int ret;
        bool soc_reset;

        /*
         * Use default READ/WRITE sequences
         */
        ret = stfsm_prepare_rwe_seqs_default(fsm);
        if (ret)
                return ret;

        /*
         * Configure 32-bit Address Support
         */
        if (flags & FLASH_FLAG_32BIT_ADDR) {
                /* Configure 'enter_32bitaddr' FSM sequence */
                stfsm_mx25_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr);

                soc_reset = stfsm_can_handle_soc_reset(fsm);
                if (soc_reset || !fsm->booted_from_spi)
                        /* If we can handle SoC resets, we enable 32-bit address
                         * mode pervasively */
                        stfsm_enter_32bit_addr(fsm, 1);

                else
                        /* Else, enable/disable 32-bit addressing before/after
                         * each operation */
                        fsm->configuration = (CFG_READ_TOGGLE_32BIT_ADDR |
                                              CFG_WRITE_TOGGLE_32BIT_ADDR |
                                              CFG_ERASESEC_TOGGLE_32BIT_ADDR);
        }

        /* Check status of 'QE' bit, update if required. */
        stfsm_read_status(fsm, SPINOR_OP_RDSR, &sta, 1);
        data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1;
        if (data_pads == 4) {
                if (!(sta & MX25_STATUS_QE)) {
                        /* Set 'QE' */
                        sta |= MX25_STATUS_QE;

                        stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1);
                }
        } else {
                if (sta & MX25_STATUS_QE) {
                        /* Clear 'QE' */
                        sta &= ~MX25_STATUS_QE;

                        stfsm_write_status(fsm, SPINOR_OP_WRSR, sta, 1, 1);
                }
        }

        return 0;
}

static int stfsm_n25q_config(struct stfsm *fsm)
{
        uint32_t flags = fsm->info->flags;
        uint8_t vcr;
        int ret = 0;
        bool soc_reset;

        /* Configure 'READ' sequence */
        if (flags & FLASH_FLAG_32BIT_ADDR)
                ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read,
                                                  n25q_read4_configs);
        else
                ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read,
                                                  n25q_read3_configs);
        if (ret) {
                dev_err(fsm->dev,
                        "failed to prepare READ sequence with flags [0x%08x]\n",
                        flags);
                return ret;
        }

        /* Configure 'WRITE' sequence (default configs) */
        ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write,
                                          default_write_configs);
        if (ret) {
                dev_err(fsm->dev,
                        "preparing WRITE sequence using flags [0x%08x] failed\n",
                        flags);
                return ret;
        }

        /* * Configure 'ERASE_SECTOR' sequence */
        stfsm_prepare_erasesec_seq(fsm, &stfsm_seq_erase_sector);

        /* Configure 32-bit address support */
        if (flags & FLASH_FLAG_32BIT_ADDR) {
                stfsm_n25q_en_32bit_addr_seq(&fsm->stfsm_seq_en_32bit_addr);

                soc_reset = stfsm_can_handle_soc_reset(fsm);
                if (soc_reset || !fsm->booted_from_spi) {
                        /*
                         * If we can handle SoC resets, we enable 32-bit
                         * address mode pervasively
                         */
                        stfsm_enter_32bit_addr(fsm, 1);
                } else {
                        /*
                         * If not, enable/disable for WRITE and ERASE
                         * operations (READ uses special commands)
                         */
                        fsm->configuration = (CFG_WRITE_TOGGLE_32BIT_ADDR |
                                              CFG_ERASESEC_TOGGLE_32BIT_ADDR);
                }
        }

        /*
         * Configure device to use 8 dummy cycles
         */
        vcr = (N25Q_VCR_DUMMY_CYCLES(8) | N25Q_VCR_XIP_DISABLED |
               N25Q_VCR_WRAP_CONT);
        stfsm_write_status(fsm, N25Q_CMD_WRVCR, vcr, 1, 0);

        return 0;
}

static void stfsm_s25fl_prepare_erasesec_seq_32(struct stfsm_seq *seq)
{
        seq->seq_opc[1] = (SEQ_OPC_PADS_1 |
                           SEQ_OPC_CYCLES(8) |
                           SEQ_OPC_OPCODE(S25FL_CMD_SE4));

        seq->addr_cfg = (ADR_CFG_CYCLES_ADD1(16) |
                         ADR_CFG_PADS_1_ADD1 |
                         ADR_CFG_CYCLES_ADD2(16) |
                         ADR_CFG_PADS_1_ADD2 |
                         ADR_CFG_CSDEASSERT_ADD2);
}

static void stfsm_s25fl_read_dyb(struct stfsm *fsm, uint32_t offs, uint8_t *dby)
{
        uint32_t tmp;
        struct stfsm_seq seq = {
                .data_size = TRANSFER_SIZE(4),
                .seq_opc[0] = (SEQ_OPC_PADS_1 |
                               SEQ_OPC_CYCLES(8) |
                               SEQ_OPC_OPCODE(S25FL_CMD_DYBRD)),
                .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) |
                             ADR_CFG_PADS_1_ADD1 |
                             ADR_CFG_CYCLES_ADD2(16) |
                             ADR_CFG_PADS_1_ADD2),
                .addr1 = (offs >> 16) & 0xffff,
                .addr2 = offs & 0xffff,
                .seq = {
                        STFSM_INST_CMD1,
                        STFSM_INST_ADD1,
                        STFSM_INST_ADD2,
                        STFSM_INST_DATA_READ,
                        STFSM_INST_STOP,
                },
                .seq_cfg = (SEQ_CFG_PADS_1 |
                            SEQ_CFG_READNOTWRITE |
                            SEQ_CFG_CSDEASSERT |
                            SEQ_CFG_STARTSEQ),
        };

        stfsm_load_seq(fsm, &seq);

        stfsm_read_fifo(fsm, &tmp, 4);

        *dby = (uint8_t)(tmp >> 24);

        stfsm_wait_seq(fsm);
}

static void stfsm_s25fl_write_dyb(struct stfsm *fsm, uint32_t offs, uint8_t dby)
{
        struct stfsm_seq seq = {
                .seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                               SEQ_OPC_OPCODE(SPINOR_OP_WREN) |
                               SEQ_OPC_CSDEASSERT),
                .seq_opc[1] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
                               SEQ_OPC_OPCODE(S25FL_CMD_DYBWR)),
                .addr_cfg = (ADR_CFG_CYCLES_ADD1(16) |
                             ADR_CFG_PADS_1_ADD1 |
                             ADR_CFG_CYCLES_ADD2(16) |
                             ADR_CFG_PADS_1_ADD2),
                .status = (uint32_t)dby | STA_PADS_1 | STA_CSDEASSERT,
                .addr1 = (offs >> 16) & 0xffff,
                .addr2 = offs & 0xffff,
                .seq = {
                        STFSM_INST_CMD1,
                        STFSM_INST_CMD2,
                        STFSM_INST_ADD1,
                        STFSM_INST_ADD2,
                        STFSM_INST_STA_WR1,
                        STFSM_INST_STOP,
                },
                .seq_cfg = (SEQ_CFG_PADS_1 |
                            SEQ_CFG_READNOTWRITE |
                            SEQ_CFG_CSDEASSERT |
                            SEQ_CFG_STARTSEQ),
        };

        stfsm_load_seq(fsm, &seq);
        stfsm_wait_seq(fsm);

        stfsm_wait_busy(fsm);
}

static int stfsm_s25fl_clear_status_reg(struct stfsm *fsm)
{
        struct stfsm_seq seq = {
                .seq_opc[0] = (SEQ_OPC_PADS_1 |
                               SEQ_OPC_CYCLES(8) |
                               SEQ_OPC_OPCODE(S25FL_CMD_CLSR) |
                               SEQ_OPC_CSDEASSERT),
                .seq_opc[1] = (SEQ_OPC_PADS_1 |
                               SEQ_OPC_CYCLES(8) |
                               SEQ_OPC_OPCODE(SPINOR_OP_WRDI) |
                               SEQ_OPC_CSDEASSERT),
                .seq = {
                        STFSM_INST_CMD1,
                        STFSM_INST_CMD2,
                        STFSM_INST_WAIT,
                        STFSM_INST_STOP,
                },
                .seq_cfg = (SEQ_CFG_PADS_1 |
                            SEQ_CFG_ERASE |
                            SEQ_CFG_READNOTWRITE |
                            SEQ_CFG_CSDEASSERT |
                            SEQ_CFG_STARTSEQ),
        };

        stfsm_load_seq(fsm, &seq);

        stfsm_wait_seq(fsm);

        return 0;
}

static int stfsm_s25fl_config(struct stfsm *fsm)
{
        struct flash_info *info = fsm->info;
        uint32_t flags = info->flags;
        uint32_t data_pads;
        uint32_t offs;
        uint16_t sta_wr;
        uint8_t sr1, cr1, dyb;
        int update_sr = 0;
        int ret;

        if (flags & FLASH_FLAG_32BIT_ADDR) {
                /*
                 * Prepare Read/Write/Erase sequences according to S25FLxxx
                 * 32-bit address command set
                 */
                ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_read,
                                                  stfsm_s25fl_read4_configs);
                if (ret)
                        return ret;

                ret = stfsm_search_prepare_rw_seq(fsm, &fsm->stfsm_seq_write,
                                                  stfsm_s25fl_write4_configs);
                if (ret)
                        return ret;

                stfsm_s25fl_prepare_erasesec_seq_32(&stfsm_seq_erase_sector);

        } else {
                /* Use default configurations for 24-bit addressing */
                ret = stfsm_prepare_rwe_seqs_default(fsm);
                if (ret)
                        return ret;
        }

        /*
         * For devices that support 'DYB' sector locking, check lock status and
         * unlock sectors if necessary (some variants power-on with sectors
         * locked by default)
         */
        if (flags & FLASH_FLAG_DYB_LOCKING) {
                offs = 0;
                for (offs = 0; offs < info->sector_size * info->n_sectors;) {
                        stfsm_s25fl_read_dyb(fsm, offs, &dyb);
                        if (dyb == 0x00)
                                stfsm_s25fl_write_dyb(fsm, offs, 0xff);

                        /* Handle bottom/top 4KiB parameter sectors */
                        if ((offs < info->sector_size * 2) ||
                            (offs >= (info->sector_size - info->n_sectors * 4)))
                                offs += 0x1000;
                        else
                                offs += 0x10000;
                }
        }

        /* Check status of 'QE' bit, update if required. */
        stfsm_read_status(fsm, SPINOR_OP_RDCR, &cr1, 1);
        data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1;
        if (data_pads == 4) {
                if (!(cr1 & STFSM_S25FL_CONFIG_QE)) {
                        /* Set 'QE' */
                        cr1 |= STFSM_S25FL_CONFIG_QE;

                        update_sr = 1;
                }
        } else {
                if (cr1 & STFSM_S25FL_CONFIG_QE) {
                        /* Clear 'QE' */
                        cr1 &= ~STFSM_S25FL_CONFIG_QE;

                        update_sr = 1;
                }
        }
        if (update_sr) {
                stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1);
                sta_wr = ((uint16_t)cr1  << 8) | sr1;
                stfsm_write_status(fsm, SPINOR_OP_WRSR, sta_wr, 2, 1);
        }

        /*
         * S25FLxxx devices support Program and Error error flags.
         * Configure driver to check flags and clear if necessary.
         */
        fsm->configuration |= CFG_S25FL_CHECK_ERROR_FLAGS;

        return 0;
}

static int stfsm_w25q_config(struct stfsm *fsm)
{
        uint32_t data_pads;
        uint8_t sr1, sr2;
        uint16_t sr_wr;
        int update_sr = 0;
        int ret;

        ret = stfsm_prepare_rwe_seqs_default(fsm);
        if (ret)
                return ret;

        /* Check status of 'QE' bit, update if required. */
        stfsm_read_status(fsm, SPINOR_OP_RDCR, &sr2, 1);
        data_pads = ((fsm->stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1;
        if (data_pads == 4) {
                if (!(sr2 & W25Q_STATUS_QE)) {
                        /* Set 'QE' */
                        sr2 |= W25Q_STATUS_QE;
                        update_sr = 1;
                }
        } else {
                if (sr2 & W25Q_STATUS_QE) {
                        /* Clear 'QE' */
                        sr2 &= ~W25Q_STATUS_QE;
                        update_sr = 1;
                }
        }
        if (update_sr) {
                /* Write status register */
                stfsm_read_status(fsm, SPINOR_OP_RDSR, &sr1, 1);
                sr_wr = ((uint16_t)sr2 << 8) | sr1;
                stfsm_write_status(fsm, SPINOR_OP_WRSR, sr_wr, 2, 1);
        }

        return 0;
}

static int stfsm_read(struct stfsm *fsm, uint8_t *buf, uint32_t size,
                      uint32_t offset)
{
        struct stfsm_seq *seq = &fsm->stfsm_seq_read;
        uint32_t data_pads;
        uint32_t read_mask;
        uint32_t size_ub;
        uint32_t size_lb;
        uint32_t size_mop;
        uint32_t tmp[4];
        uint32_t page_buf[FLASH_PAGESIZE_32];
        uint8_t *p;

        dev_dbg(fsm->dev, "reading %d bytes from 0x%08x\n", size, offset);

        /* Enter 32-bit address mode, if required */
        if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 1);

        /* Must read in multiples of 32 cycles (or 32*pads/8 Bytes) */
        data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1;
        read_mask = (data_pads << 2) - 1;

        /* Handle non-aligned buf */
        p = ((uintptr_t)buf & 0x3) ? (uint8_t *)page_buf : buf;

        /* Handle non-aligned size */
        size_ub = (size + read_mask) & ~read_mask;
        size_lb = size & ~read_mask;
        size_mop = size & read_mask;

        seq->data_size = TRANSFER_SIZE(size_ub);
        seq->addr1 = (offset >> 16) & 0xffff;
        seq->addr2 = offset & 0xffff;

        stfsm_load_seq(fsm, seq);

        if (size_lb)
                stfsm_read_fifo(fsm, (uint32_t *)p, size_lb);

        if (size_mop) {
                stfsm_read_fifo(fsm, tmp, read_mask + 1);
                memcpy(p + size_lb, &tmp, size_mop);
        }

        /* Handle non-aligned buf */
        if ((uintptr_t)buf & 0x3)
                memcpy(buf, page_buf, size);

        /* Wait for sequence to finish */
        stfsm_wait_seq(fsm);

        stfsm_clear_fifo(fsm);

        /* Exit 32-bit address mode, if required */
        if (fsm->configuration & CFG_READ_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 0);

        return 0;
}

static int stfsm_write(struct stfsm *fsm, const uint8_t *buf,
                       uint32_t size, uint32_t offset)
{
        struct stfsm_seq *seq = &fsm->stfsm_seq_write;
        uint32_t data_pads;
        uint32_t write_mask;
        uint32_t size_ub;
        uint32_t size_lb;
        uint32_t size_mop;
        uint32_t tmp[4];
        uint32_t i;
        uint32_t page_buf[FLASH_PAGESIZE_32];
        uint8_t *t = (uint8_t *)&tmp;
        const uint8_t *p;
        int ret;

        dev_dbg(fsm->dev, "writing %d bytes to 0x%08x\n", size, offset);

        /* Enter 32-bit address mode, if required */
        if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 1);

        /* Must write in multiples of 32 cycles (or 32*pads/8 bytes) */
        data_pads = ((seq->seq_cfg >> 16) & 0x3) + 1;
        write_mask = (data_pads << 2) - 1;

        /* Handle non-aligned buf */
        if ((uintptr_t)buf & 0x3) {
                memcpy(page_buf, buf, size);
                p = (uint8_t *)page_buf;
        } else {
                p = buf;
        }

        /* Handle non-aligned size */
        size_ub = (size + write_mask) & ~write_mask;
        size_lb = size & ~write_mask;
        size_mop = size & write_mask;

        seq->data_size = TRANSFER_SIZE(size_ub);
        seq->addr1 = (offset >> 16) & 0xffff;
        seq->addr2 = offset & 0xffff;

        /* Need to set FIFO to write mode, before writing data to FIFO (see
         * GNBvb79594)
         */
        writel(0x00040000, fsm->base + SPI_FAST_SEQ_CFG);

        /*
         * Before writing data to the FIFO, apply a small delay to allow a
         * potential change of FIFO direction to complete.
         */
        if (fsm->fifo_dir_delay == 0)
                readl(fsm->base + SPI_FAST_SEQ_CFG);
        else
                udelay(fsm->fifo_dir_delay);


        /* Write data to FIFO, before starting sequence (see GNBvd79593) */
        if (size_lb) {
                stfsm_write_fifo(fsm, (uint32_t *)p, size_lb);
                p += size_lb;
        }

        /* Handle non-aligned size */
        if (size_mop) {
                memset(t, 0xff, write_mask + 1);        /* fill with 0xff's */
                for (i = 0; i < size_mop; i++)
                        t[i] = *p++;

                stfsm_write_fifo(fsm, tmp, write_mask + 1);
        }

        /* Start sequence */
        stfsm_load_seq(fsm, seq);

        /* Wait for sequence to finish */
        stfsm_wait_seq(fsm);

        /* Wait for completion */
        ret = stfsm_wait_busy(fsm);
        if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS)
                stfsm_s25fl_clear_status_reg(fsm);

        /* Exit 32-bit address mode, if required */
        if (fsm->configuration & CFG_WRITE_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 0);

        return 0;
}

/*
 * Read an address range from the flash chip. The address range
 * may be any size provided it is within the physical boundaries.
 */
static int stfsm_mtd_read(struct mtd_info *mtd, loff_t from, size_t len,
                          size_t *retlen, u_char *buf)
{
        struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent);
        uint32_t bytes;

        dev_dbg(fsm->dev, "%s from 0x%08x, len %zd\n",
                __func__, (u32)from, len);

        mutex_lock(&fsm->lock);

        while (len > 0) {
                bytes = min_t(size_t, len, FLASH_PAGESIZE);

                stfsm_read(fsm, buf, bytes, from);

                buf += bytes;
                from += bytes;
                len -= bytes;

                *retlen += bytes;
        }

        mutex_unlock(&fsm->lock);

        return 0;
}

static int stfsm_erase_sector(struct stfsm *fsm, uint32_t offset)
{
        struct stfsm_seq *seq = &stfsm_seq_erase_sector;
        int ret;

        dev_dbg(fsm->dev, "erasing sector at 0x%08x\n", offset);

        /* Enter 32-bit address mode, if required */
        if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 1);

        seq->addr1 = (offset >> 16) & 0xffff;
        seq->addr2 = offset & 0xffff;

        stfsm_load_seq(fsm, seq);

        stfsm_wait_seq(fsm);

        /* Wait for completion */
        ret = stfsm_wait_busy(fsm);
        if (ret && fsm->configuration & CFG_S25FL_CHECK_ERROR_FLAGS)
                stfsm_s25fl_clear_status_reg(fsm);

        /* Exit 32-bit address mode, if required */
        if (fsm->configuration & CFG_ERASESEC_TOGGLE_32BIT_ADDR)
                stfsm_enter_32bit_addr(fsm, 0);

        return ret;
}

static int stfsm_erase_chip(struct stfsm *fsm)
{
        const struct stfsm_seq *seq = &stfsm_seq_erase_chip;

        dev_dbg(fsm->dev, "erasing chip\n");

        stfsm_load_seq(fsm, seq);

        stfsm_wait_seq(fsm);

        return stfsm_wait_busy(fsm);
}

/*
 * Write an address range to the flash chip.  Data must be written in
 * FLASH_PAGESIZE chunks.  The address range may be any size provided
 * it is within the physical boundaries.
 */
static int stfsm_mtd_write(struct mtd_info *mtd, loff_t to, size_t len,
                           size_t *retlen, const u_char *buf)
{
        struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent);

        u32 page_offs;
        u32 bytes;
        uint8_t *b = (uint8_t *)buf;
        int ret = 0;

        dev_dbg(fsm->dev, "%s to 0x%08x, len %zd\n", __func__, (u32)to, len);

        /* Offset within page */
        page_offs = to % FLASH_PAGESIZE;

        mutex_lock(&fsm->lock);

        while (len) {
                /* Write up to page boundary */
                bytes = min_t(size_t, FLASH_PAGESIZE - page_offs, len);

                ret = stfsm_write(fsm, b, bytes, to);
                if (ret)
                        goto out1;

                b += bytes;
                len -= bytes;
                to += bytes;

                /* We are now page-aligned */
                page_offs = 0;

                *retlen += bytes;

        }

out1:
        mutex_unlock(&fsm->lock);

        return ret;
}

/*
 * Erase an address range on the flash chip. The address range may extend
 * one or more erase sectors.  Return an error is there is a problem erasing.
 */
static int stfsm_mtd_erase(struct mtd_info *mtd, struct erase_info *instr)
{
        struct stfsm *fsm = dev_get_drvdata(mtd->dev.parent);
        u32 addr, len;
        int ret;

        dev_dbg(fsm->dev, "%s at 0x%llx, len %lld\n", __func__,
                (long long)instr->addr, (long long)instr->len);

        addr = instr->addr;
        len = instr->len;

        mutex_lock(&fsm->lock);

        /* Whole-chip erase? */
        if (len == mtd->size) {
                ret = stfsm_erase_chip(fsm);
                if (ret)
                        goto out1;
        } else {
                while (len) {
                        ret = stfsm_erase_sector(fsm, addr);
                        if (ret)
                                goto out1;

                        addr += mtd->erasesize;
                        len -= mtd->erasesize;
                }
        }

        mutex_unlock(&fsm->lock);

        return 0;

out1:
        mutex_unlock(&fsm->lock);

        return ret;
}

static void stfsm_read_jedec(struct stfsm *fsm, uint8_t *jedec)
{
        const struct stfsm_seq *seq = &stfsm_seq_read_jedec;
        uint32_t tmp[2];

        stfsm_load_seq(fsm, seq);

        stfsm_read_fifo(fsm, tmp, 8);

        memcpy(jedec, tmp, 5);

        stfsm_wait_seq(fsm);
}

static struct flash_info *stfsm_jedec_probe(struct stfsm *fsm)
{
        struct flash_info       *info;
        u16                     ext_jedec;
        u32                     jedec;
        u8                      id[5];

        stfsm_read_jedec(fsm, id);

        jedec     = id[0] << 16 | id[1] << 8 | id[2];
        /*
         * JEDEC also defines an optional "extended device information"
         * string for after vendor-specific data, after the three bytes
         * we use here. Supporting some chips might require using it.
         */
        ext_jedec = id[3] << 8  | id[4];

        dev_dbg(fsm->dev, "JEDEC =  0x%08x [%5ph]\n", jedec, id);

        for (info = flash_types; info->name; info++) {
                if (info->jedec_id == jedec) {
                        if (info->ext_id && info->ext_id != ext_jedec)
                                continue;
                        return info;
                }
        }
        dev_err(fsm->dev, "Unrecognized JEDEC id %06x\n", jedec);

        return NULL;
}

static int stfsm_set_mode(struct stfsm *fsm, uint32_t mode)
{
        int ret, timeout = 10;

        /* Wait for controller to accept mode change */
        while (--timeout) {
                ret = readl(fsm->base + SPI_STA_MODE_CHANGE);
                if (ret & 0x1)
                        break;
                udelay(1);
        }

        if (!timeout)
                return -EBUSY;

        writel(mode, fsm->base + SPI_MODESELECT);

        return 0;
}

static void stfsm_set_freq(struct stfsm *fsm, uint32_t spi_freq)
{
        uint32_t emi_freq;
        uint32_t clk_div;

        emi_freq = clk_get_rate(fsm->clk);

        /*
         * Calculate clk_div - values between 2 and 128
         * Multiple of 2, rounded up
         */
        clk_div = 2 * DIV_ROUND_UP(emi_freq, 2 * spi_freq);
        if (clk_div < 2)
                clk_div = 2;
        else if (clk_div > 128)
                clk_div = 128;

        /*
         * Determine a suitable delay for the IP to complete a change of
         * direction of the FIFO. The required delay is related to the clock
         * divider used. The following heuristics are based on empirical tests,
         * using a 100MHz EMI clock.
         */
        if (clk_div <= 4)
                fsm->fifo_dir_delay = 0;
        else if (clk_div <= 10)
                fsm->fifo_dir_delay = 1;
        else
                fsm->fifo_dir_delay = DIV_ROUND_UP(clk_div, 10);

        dev_dbg(fsm->dev, "emi_clk = %uHZ, spi_freq = %uHZ, clk_div = %u\n",
                emi_freq, spi_freq, clk_div);

        writel(clk_div, fsm->base + SPI_CLOCKDIV);
}

static int stfsm_init(struct stfsm *fsm)
{
        int ret;

        /* Perform a soft reset of the FSM controller */
        writel(SEQ_CFG_SWRESET, fsm->base + SPI_FAST_SEQ_CFG);
        udelay(1);
        writel(0, fsm->base + SPI_FAST_SEQ_CFG);

        /* Set clock to 'safe' frequency initially */
        stfsm_set_freq(fsm, STFSM_FLASH_SAFE_FREQ);

        /* Switch to FSM */
        ret = stfsm_set_mode(fsm, SPI_MODESELECT_FSM);
        if (ret)
                return ret;

        /* Set timing parameters */
        writel(SPI_CFG_DEVICE_ST            |
               SPI_CFG_DEFAULT_MIN_CS_HIGH  |
               SPI_CFG_DEFAULT_CS_SETUPHOLD |
               SPI_CFG_DEFAULT_DATA_HOLD,
               fsm->base + SPI_CONFIGDATA);
        writel(STFSM_DEFAULT_WR_TIME, fsm->base + SPI_STATUS_WR_TIME_REG);

        /*
         * Set the FSM 'WAIT' delay to the minimum workable value.  Note, for
         * our purposes, the WAIT instruction is used purely to achieve
         * "sequence validity" rather than actually implement a delay.
         */
        writel(0x00000001, fsm->base + SPI_PROGRAM_ERASE_TIME);

        /* Clear FIFO, just in case */
        stfsm_clear_fifo(fsm);

        return 0;
}

static void stfsm_fetch_platform_configs(struct platform_device *pdev)
{
        struct stfsm *fsm = platform_get_drvdata(pdev);
        struct device_node *np = pdev->dev.of_node;
        struct regmap *regmap;
        uint32_t boot_device_reg;
        uint32_t boot_device_spi;
        uint32_t boot_device;     /* Value we read from *boot_device_reg */
        int ret;

        /* Booting from SPI NOR Flash is the default */
        fsm->booted_from_spi = true;

        regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
        if (IS_ERR(regmap))
                goto boot_device_fail;

        fsm->reset_signal = of_property_read_bool(np, "st,reset-signal");

        fsm->reset_por = of_property_read_bool(np, "st,reset-por");

        /* Where in the syscon the boot device information lives */
        ret = of_property_read_u32(np, "st,boot-device-reg", &boot_device_reg);
        if (ret)
                goto boot_device_fail;

        /* Boot device value when booted from SPI NOR */
        ret = of_property_read_u32(np, "st,boot-device-spi", &boot_device_spi);
        if (ret)
                goto boot_device_fail;

        ret = regmap_read(regmap, boot_device_reg, &boot_device);
        if (ret)
                goto boot_device_fail;

        if (boot_device != boot_device_spi)
                fsm->booted_from_spi = false;

        return;

boot_device_fail:
        dev_warn(&pdev->dev,
                 "failed to fetch boot device, assuming boot from SPI\n");
}

static int stfsm_probe(struct platform_device *pdev)
{
        struct device_node *np = pdev->dev.of_node;
        struct flash_info *info;
        struct resource *res;
        struct stfsm *fsm;
        int ret;

        if (!np) {
                dev_err(&pdev->dev, "No DT found\n");
                return -EINVAL;
        }

        fsm = devm_kzalloc(&pdev->dev, sizeof(*fsm), GFP_KERNEL);
        if (!fsm)
                return -ENOMEM;

        fsm->dev = &pdev->dev;

        platform_set_drvdata(pdev, fsm);

        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        if (!res) {
                dev_err(&pdev->dev, "Resource not found\n");
                return -ENODEV;
        }

        fsm->base = devm_ioremap_resource(&pdev->dev, res);
        if (IS_ERR(fsm->base)) {
                dev_err(&pdev->dev,
                        "Failed to reserve memory region %pR\n", res);
                return PTR_ERR(fsm->base);
        }

        fsm->clk = devm_clk_get(&pdev->dev, NULL);
        if (IS_ERR(fsm->clk)) {
                dev_err(fsm->dev, "Couldn't find EMI clock.\n");
                return PTR_ERR(fsm->clk);
        }

        ret = clk_prepare_enable(fsm->clk);
        if (ret) {
                dev_err(fsm->dev, "Failed to enable EMI clock.\n");
                return ret;
        }

        mutex_init(&fsm->lock);

        ret = stfsm_init(fsm);
        if (ret) {
                dev_err(&pdev->dev, "Failed to initialise FSM Controller\n");
                goto err_clk_unprepare;
        }

        stfsm_fetch_platform_configs(pdev);

        /* Detect SPI FLASH device */
        info = stfsm_jedec_probe(fsm);
        if (!info) {
                ret = -ENODEV;
                goto err_clk_unprepare;
        }
        fsm->info = info;

        /* Use device size to determine address width */
        if (info->sector_size * info->n_sectors > 0x1000000)
                info->flags |= FLASH_FLAG_32BIT_ADDR;

        /*
         * Configure READ/WRITE/ERASE sequences according to platform and
         * device flags.
         */
        if (info->config) {
                ret = info->config(fsm);
                if (ret)
                        goto err_clk_unprepare;
        } else {
                ret = stfsm_prepare_rwe_seqs_default(fsm);
                if (ret)
                        goto err_clk_unprepare;
        }

        fsm->mtd.name           = info->name;
        fsm->mtd.dev.parent     = &pdev->dev;
        mtd_set_of_node(&fsm->mtd, np);
        fsm->mtd.type           = MTD_NORFLASH;
        fsm->mtd.writesize      = 4;
        fsm->mtd.writebufsize   = fsm->mtd.writesize;
        fsm->mtd.flags          = MTD_CAP_NORFLASH;
        fsm->mtd.size           = info->sector_size * info->n_sectors;
        fsm->mtd.erasesize      = info->sector_size;

        fsm->mtd._read  = stfsm_mtd_read;
        fsm->mtd._write = stfsm_mtd_write;
        fsm->mtd._erase = stfsm_mtd_erase;

        dev_info(&pdev->dev,
                "Found serial flash device: %s\n"
                " size = %llx (%lldMiB) erasesize = 0x%08x (%uKiB)\n",
                info->name,
                (long long)fsm->mtd.size, (long long)(fsm->mtd.size >> 20),
                fsm->mtd.erasesize, (fsm->mtd.erasesize >> 10));

        return mtd_device_register(&fsm->mtd, NULL, 0);

err_clk_unprepare:
        clk_disable_unprepare(fsm->clk);
        return ret;
}

static int stfsm_remove(struct platform_device *pdev)
{
        struct stfsm *fsm = platform_get_drvdata(pdev);

        return mtd_device_unregister(&fsm->mtd);
}

#ifdef CONFIG_PM_SLEEP
static int stfsmfsm_suspend(struct device *dev)
{
        struct stfsm *fsm = dev_get_drvdata(dev);

        clk_disable_unprepare(fsm->clk);

        return 0;
}

static int stfsmfsm_resume(struct device *dev)
{
        struct stfsm *fsm = dev_get_drvdata(dev);

        return clk_prepare_enable(fsm->clk);
}
#endif

static SIMPLE_DEV_PM_OPS(stfsm_pm_ops, stfsmfsm_suspend, stfsmfsm_resume);

static const struct of_device_id stfsm_match[] = {
        { .compatible = "st,spi-fsm", },
        {},
};
MODULE_DEVICE_TABLE(of, stfsm_match);

static struct platform_driver stfsm_driver = {
        .probe          = stfsm_probe,
        .remove         = stfsm_remove,
        .driver         = {
                .name   = "st-spi-fsm",
                .of_match_table = stfsm_match,
                .pm     = &stfsm_pm_ops,
        },
};
module_platform_driver(stfsm_driver);

MODULE_AUTHOR("Angus Clark <angus.clark@st.com>");
MODULE_DESCRIPTION("ST SPI FSM driver");
MODULE_LICENSE("GPL");