1
2
3
4
5
6
7
8
9
10
11#include <linux/dma-mapping.h>
12#include <linux/kernel.h>
13#include <linux/module.h>
14#include <linux/of_address.h>
15#include <linux/of_irq.h>
16#include <linux/platform_device.h>
17
18#include "mtu3.h"
19
20static int ep_fifo_alloc(struct mtu3_ep *mep, u32 seg_size)
21{
22 struct mtu3_fifo_info *fifo = mep->fifo;
23 u32 num_bits = DIV_ROUND_UP(seg_size, MTU3_EP_FIFO_UNIT);
24 u32 start_bit;
25
26
27 num_bits = roundup_pow_of_two(num_bits);
28 if (num_bits > fifo->limit)
29 return -EINVAL;
30
31 mep->fifo_seg_size = num_bits * MTU3_EP_FIFO_UNIT;
32 num_bits = num_bits * (mep->slot + 1);
33 start_bit = bitmap_find_next_zero_area(fifo->bitmap,
34 fifo->limit, 0, num_bits, 0);
35 if (start_bit >= fifo->limit)
36 return -EOVERFLOW;
37
38 bitmap_set(fifo->bitmap, start_bit, num_bits);
39 mep->fifo_size = num_bits * MTU3_EP_FIFO_UNIT;
40 mep->fifo_addr = fifo->base + MTU3_EP_FIFO_UNIT * start_bit;
41
42 dev_dbg(mep->mtu->dev, "%s fifo:%#x/%#x, start_bit: %d\n",
43 __func__, mep->fifo_seg_size, mep->fifo_size, start_bit);
44
45 return mep->fifo_addr;
46}
47
48static void ep_fifo_free(struct mtu3_ep *mep)
49{
50 struct mtu3_fifo_info *fifo = mep->fifo;
51 u32 addr = mep->fifo_addr;
52 u32 bits = mep->fifo_size / MTU3_EP_FIFO_UNIT;
53 u32 start_bit;
54
55 if (unlikely(addr < fifo->base || bits > fifo->limit))
56 return;
57
58 start_bit = (addr - fifo->base) / MTU3_EP_FIFO_UNIT;
59 bitmap_clear(fifo->bitmap, start_bit, bits);
60 mep->fifo_size = 0;
61 mep->fifo_seg_size = 0;
62
63 dev_dbg(mep->mtu->dev, "%s size:%#x/%#x, start_bit: %d\n",
64 __func__, mep->fifo_seg_size, mep->fifo_size, start_bit);
65}
66
67
68static inline void mtu3_ss_func_set(struct mtu3 *mtu, bool enable)
69{
70
71 if (enable)
72 mtu3_setbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
73 else
74 mtu3_clrbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
75
76 dev_dbg(mtu->dev, "USB3_EN = %d\n", !!enable);
77}
78
79
80static inline void mtu3_hs_softconn_set(struct mtu3 *mtu, bool enable)
81{
82 if (enable) {
83 mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT,
84 SOFT_CONN | SUSPENDM_ENABLE);
85 } else {
86 mtu3_clrbits(mtu->mac_base, U3D_POWER_MANAGEMENT,
87 SOFT_CONN | SUSPENDM_ENABLE);
88 }
89 dev_dbg(mtu->dev, "SOFTCONN = %d\n", !!enable);
90}
91
92
93static int mtu3_device_enable(struct mtu3 *mtu)
94{
95 void __iomem *ibase = mtu->ippc_base;
96 u32 check_clk = 0;
97
98 mtu3_clrbits(ibase, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
99
100 if (mtu->is_u3_ip) {
101 check_clk = SSUSB_U3_MAC_RST_B_STS;
102 mtu3_clrbits(ibase, SSUSB_U3_CTRL(0),
103 (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN |
104 SSUSB_U3_PORT_HOST_SEL));
105 }
106 mtu3_clrbits(ibase, SSUSB_U2_CTRL(0),
107 (SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN |
108 SSUSB_U2_PORT_HOST_SEL));
109
110 if (mtu->ssusb->dr_mode == USB_DR_MODE_OTG)
111 mtu3_setbits(ibase, SSUSB_U2_CTRL(0), SSUSB_U2_PORT_OTG_SEL);
112
113 return ssusb_check_clocks(mtu->ssusb, check_clk);
114}
115
116static void mtu3_device_disable(struct mtu3 *mtu)
117{
118 void __iomem *ibase = mtu->ippc_base;
119
120 if (mtu->is_u3_ip)
121 mtu3_setbits(ibase, SSUSB_U3_CTRL(0),
122 (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN));
123
124 mtu3_setbits(ibase, SSUSB_U2_CTRL(0),
125 SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN);
126
127 if (mtu->ssusb->dr_mode == USB_DR_MODE_OTG)
128 mtu3_clrbits(ibase, SSUSB_U2_CTRL(0), SSUSB_U2_PORT_OTG_SEL);
129
130 mtu3_setbits(ibase, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
131}
132
133
134static void mtu3_device_reset(struct mtu3 *mtu)
135{
136 void __iomem *ibase = mtu->ippc_base;
137
138 mtu3_setbits(ibase, U3D_SSUSB_DEV_RST_CTRL, SSUSB_DEV_SW_RST);
139 udelay(1);
140 mtu3_clrbits(ibase, U3D_SSUSB_DEV_RST_CTRL, SSUSB_DEV_SW_RST);
141}
142
143
144static void mtu3_intr_disable(struct mtu3 *mtu)
145{
146 void __iomem *mbase = mtu->mac_base;
147
148
149 mtu3_writel(mbase, U3D_LV1IECR, ~0x0);
150
151 mtu3_writel(mbase, U3D_EPIECR, ~0x0);
152}
153
154static void mtu3_intr_status_clear(struct mtu3 *mtu)
155{
156 void __iomem *mbase = mtu->mac_base;
157
158
159 mtu3_writel(mbase, U3D_EPISR, ~0x0);
160
161 mtu3_writel(mbase, U3D_COMMON_USB_INTR, ~0x0);
162
163 mtu3_writel(mbase, U3D_LTSSM_INTR, ~0x0);
164
165 mtu3_writel(mbase, U3D_DEV_LINK_INTR, ~0x0);
166}
167
168
169static void mtu3_intr_enable(struct mtu3 *mtu)
170{
171 void __iomem *mbase = mtu->mac_base;
172 u32 value;
173
174
175 value = BMU_INTR | QMU_INTR | MAC3_INTR | MAC2_INTR | EP_CTRL_INTR;
176 mtu3_writel(mbase, U3D_LV1IESR, value);
177
178
179 value = SUSPEND_INTR | RESUME_INTR | RESET_INTR | LPM_RESUME_INTR;
180 mtu3_writel(mbase, U3D_COMMON_USB_INTR_ENABLE, value);
181
182 if (mtu->is_u3_ip) {
183
184 value = HOT_RST_INTR | WARM_RST_INTR | VBUS_RISE_INTR |
185 VBUS_FALL_INTR | ENTER_U3_INTR | EXIT_U3_INTR;
186 mtu3_writel(mbase, U3D_LTSSM_INTR_ENABLE, value);
187 }
188
189
190 value = TXQ_CSERR_INT | TXQ_LENERR_INT | RXQ_CSERR_INT |
191 RXQ_LENERR_INT | RXQ_ZLPERR_INT;
192 mtu3_writel(mbase, U3D_QIESR1, value);
193
194
195 mtu3_writel(mbase, U3D_DEV_LINK_INTR_ENABLE, SSUSB_DEV_SPEED_CHG_INTR);
196}
197
198
199static void mtu3_ep_reset(struct mtu3_ep *mep)
200{
201 struct mtu3 *mtu = mep->mtu;
202 u32 rst_bit = EP_RST(mep->is_in, mep->epnum);
203
204 mtu3_setbits(mtu->mac_base, U3D_EP_RST, rst_bit);
205 mtu3_clrbits(mtu->mac_base, U3D_EP_RST, rst_bit);
206}
207
208
209void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set)
210{
211 struct mtu3 *mtu = mep->mtu;
212 void __iomem *mbase = mtu->mac_base;
213 u8 epnum = mep->epnum;
214 u32 csr;
215
216 if (mep->is_in) {
217 csr = mtu3_readl(mbase, MU3D_EP_TXCR0(epnum)) & TX_W1C_BITS;
218 if (set)
219 csr |= TX_SENDSTALL;
220 else
221 csr = (csr & (~TX_SENDSTALL)) | TX_SENTSTALL;
222 mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), csr);
223 } else {
224 csr = mtu3_readl(mbase, MU3D_EP_RXCR0(epnum)) & RX_W1C_BITS;
225 if (set)
226 csr |= RX_SENDSTALL;
227 else
228 csr = (csr & (~RX_SENDSTALL)) | RX_SENTSTALL;
229 mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), csr);
230 }
231
232 if (!set) {
233 mtu3_ep_reset(mep);
234 mep->flags &= ~MTU3_EP_STALL;
235 } else {
236 mep->flags |= MTU3_EP_STALL;
237 }
238
239 dev_dbg(mtu->dev, "%s: %s\n", mep->name,
240 set ? "SEND STALL" : "CLEAR STALL, with EP RESET");
241}
242
243void mtu3_dev_on_off(struct mtu3 *mtu, int is_on)
244{
245 if (mtu->is_u3_ip && mtu->max_speed >= USB_SPEED_SUPER)
246 mtu3_ss_func_set(mtu, is_on);
247 else
248 mtu3_hs_softconn_set(mtu, is_on);
249
250 dev_info(mtu->dev, "gadget (%s) pullup D%s\n",
251 usb_speed_string(mtu->max_speed), is_on ? "+" : "-");
252}
253
254void mtu3_start(struct mtu3 *mtu)
255{
256 void __iomem *mbase = mtu->mac_base;
257
258 dev_dbg(mtu->dev, "%s devctl 0x%x\n", __func__,
259 mtu3_readl(mbase, U3D_DEVICE_CONTROL));
260
261 mtu3_clrbits(mtu->ippc_base, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
262
263
264
265
266
267
268 if (mtu->max_speed == USB_SPEED_FULL)
269 mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
270
271
272 mtu3_intr_enable(mtu);
273 mtu->is_active = 1;
274
275 if (mtu->softconnect)
276 mtu3_dev_on_off(mtu, 1);
277}
278
279void mtu3_stop(struct mtu3 *mtu)
280{
281 dev_dbg(mtu->dev, "%s\n", __func__);
282
283 mtu3_intr_disable(mtu);
284 mtu3_intr_status_clear(mtu);
285
286 if (mtu->softconnect)
287 mtu3_dev_on_off(mtu, 0);
288
289 mtu->is_active = 0;
290 mtu3_setbits(mtu->ippc_base, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
291}
292
293
294int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
295 int interval, int burst, int mult)
296{
297 void __iomem *mbase = mtu->mac_base;
298 int epnum = mep->epnum;
299 u32 csr0, csr1, csr2;
300 int fifo_sgsz, fifo_addr;
301 int num_pkts;
302
303 fifo_addr = ep_fifo_alloc(mep, mep->maxp);
304 if (fifo_addr < 0) {
305 dev_err(mtu->dev, "alloc ep fifo failed(%d)\n", mep->maxp);
306 return -ENOMEM;
307 }
308 fifo_sgsz = ilog2(mep->fifo_seg_size);
309 dev_dbg(mtu->dev, "%s fifosz: %x(%x/%x)\n", __func__, fifo_sgsz,
310 mep->fifo_seg_size, mep->fifo_size);
311
312 if (mep->is_in) {
313 csr0 = TX_TXMAXPKTSZ(mep->maxp);
314 csr0 |= TX_DMAREQEN;
315
316 num_pkts = (burst + 1) * (mult + 1) - 1;
317 csr1 = TX_SS_BURST(burst) | TX_SLOT(mep->slot);
318 csr1 |= TX_MAX_PKT(num_pkts) | TX_MULT(mult);
319
320 csr2 = TX_FIFOADDR(fifo_addr >> 4);
321 csr2 |= TX_FIFOSEGSIZE(fifo_sgsz);
322
323 switch (mep->type) {
324 case USB_ENDPOINT_XFER_BULK:
325 csr1 |= TX_TYPE(TYPE_BULK);
326 break;
327 case USB_ENDPOINT_XFER_ISOC:
328 csr1 |= TX_TYPE(TYPE_ISO);
329 csr2 |= TX_BINTERVAL(interval);
330 break;
331 case USB_ENDPOINT_XFER_INT:
332 csr1 |= TX_TYPE(TYPE_INT);
333 csr2 |= TX_BINTERVAL(interval);
334 break;
335 }
336
337
338 mtu3_setbits(mbase, U3D_QIESR0, QMU_TX_DONE_INT(epnum));
339
340 mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), csr0);
341 mtu3_writel(mbase, MU3D_EP_TXCR1(epnum), csr1);
342 mtu3_writel(mbase, MU3D_EP_TXCR2(epnum), csr2);
343
344 dev_dbg(mtu->dev, "U3D_TX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
345 epnum, mtu3_readl(mbase, MU3D_EP_TXCR0(epnum)),
346 mtu3_readl(mbase, MU3D_EP_TXCR1(epnum)),
347 mtu3_readl(mbase, MU3D_EP_TXCR2(epnum)));
348 } else {
349 csr0 = RX_RXMAXPKTSZ(mep->maxp);
350 csr0 |= RX_DMAREQEN;
351
352 num_pkts = (burst + 1) * (mult + 1) - 1;
353 csr1 = RX_SS_BURST(burst) | RX_SLOT(mep->slot);
354 csr1 |= RX_MAX_PKT(num_pkts) | RX_MULT(mult);
355
356 csr2 = RX_FIFOADDR(fifo_addr >> 4);
357 csr2 |= RX_FIFOSEGSIZE(fifo_sgsz);
358
359 switch (mep->type) {
360 case USB_ENDPOINT_XFER_BULK:
361 csr1 |= RX_TYPE(TYPE_BULK);
362 break;
363 case USB_ENDPOINT_XFER_ISOC:
364 csr1 |= RX_TYPE(TYPE_ISO);
365 csr2 |= RX_BINTERVAL(interval);
366 break;
367 case USB_ENDPOINT_XFER_INT:
368 csr1 |= RX_TYPE(TYPE_INT);
369 csr2 |= RX_BINTERVAL(interval);
370 break;
371 }
372
373
374 mtu3_setbits(mbase, U3D_QIESR0, QMU_RX_DONE_INT(epnum));
375
376 mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), csr0);
377 mtu3_writel(mbase, MU3D_EP_RXCR1(epnum), csr1);
378 mtu3_writel(mbase, MU3D_EP_RXCR2(epnum), csr2);
379
380 dev_dbg(mtu->dev, "U3D_RX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
381 epnum, mtu3_readl(mbase, MU3D_EP_RXCR0(epnum)),
382 mtu3_readl(mbase, MU3D_EP_RXCR1(epnum)),
383 mtu3_readl(mbase, MU3D_EP_RXCR2(epnum)));
384 }
385
386 dev_dbg(mtu->dev, "csr0:%#x, csr1:%#x, csr2:%#x\n", csr0, csr1, csr2);
387 dev_dbg(mtu->dev, "%s: %s, fifo-addr:%#x, fifo-size:%#x(%#x/%#x)\n",
388 __func__, mep->name, mep->fifo_addr, mep->fifo_size,
389 fifo_sgsz, mep->fifo_seg_size);
390
391 return 0;
392}
393
394
395void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep)
396{
397 void __iomem *mbase = mtu->mac_base;
398 int epnum = mep->epnum;
399
400 if (mep->is_in) {
401 mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), 0);
402 mtu3_writel(mbase, MU3D_EP_TXCR1(epnum), 0);
403 mtu3_writel(mbase, MU3D_EP_TXCR2(epnum), 0);
404 mtu3_setbits(mbase, U3D_QIECR0, QMU_TX_DONE_INT(epnum));
405 } else {
406 mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), 0);
407 mtu3_writel(mbase, MU3D_EP_RXCR1(epnum), 0);
408 mtu3_writel(mbase, MU3D_EP_RXCR2(epnum), 0);
409 mtu3_setbits(mbase, U3D_QIECR0, QMU_RX_DONE_INT(epnum));
410 }
411
412 mtu3_ep_reset(mep);
413 ep_fifo_free(mep);
414
415 dev_dbg(mtu->dev, "%s: %s\n", __func__, mep->name);
416}
417
418
419
420
421
422
423
424
425
426
427
428
429
430static void get_ep_fifo_config(struct mtu3 *mtu)
431{
432 struct mtu3_fifo_info *tx_fifo;
433 struct mtu3_fifo_info *rx_fifo;
434 u32 fifosize;
435
436 if (mtu->is_u3_ip) {
437 fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
438 tx_fifo = &mtu->tx_fifo;
439 tx_fifo->base = 0;
440 tx_fifo->limit = fifosize / MTU3_EP_FIFO_UNIT;
441 bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
442
443 fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNRXFFSZ);
444 rx_fifo = &mtu->rx_fifo;
445 rx_fifo->base = 0;
446 rx_fifo->limit = fifosize / MTU3_EP_FIFO_UNIT;
447 bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
448 mtu->slot = MTU3_U3_IP_SLOT_DEFAULT;
449 } else {
450 fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
451 tx_fifo = &mtu->tx_fifo;
452 tx_fifo->base = MTU3_U2_IP_EP0_FIFO_SIZE;
453 tx_fifo->limit = (fifosize / MTU3_EP_FIFO_UNIT) >> 1;
454 bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
455
456 rx_fifo = &mtu->rx_fifo;
457 rx_fifo->base =
458 tx_fifo->base + tx_fifo->limit * MTU3_EP_FIFO_UNIT;
459 rx_fifo->limit = tx_fifo->limit;
460 bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
461 mtu->slot = MTU3_U2_IP_SLOT_DEFAULT;
462 }
463
464 dev_dbg(mtu->dev, "%s, TX: base-%d, limit-%d; RX: base-%d, limit-%d\n",
465 __func__, tx_fifo->base, tx_fifo->limit,
466 rx_fifo->base, rx_fifo->limit);
467}
468
469void mtu3_ep0_setup(struct mtu3 *mtu)
470{
471 u32 maxpacket = mtu->g.ep0->maxpacket;
472 u32 csr;
473
474 dev_dbg(mtu->dev, "%s maxpacket: %d\n", __func__, maxpacket);
475
476 csr = mtu3_readl(mtu->mac_base, U3D_EP0CSR);
477 csr &= ~EP0_MAXPKTSZ_MSK;
478 csr |= EP0_MAXPKTSZ(maxpacket);
479 csr &= EP0_W1C_BITS;
480 mtu3_writel(mtu->mac_base, U3D_EP0CSR, csr);
481
482
483 mtu3_writel(mtu->mac_base, U3D_EPIESR, EP0ISR);
484}
485
486static int mtu3_mem_alloc(struct mtu3 *mtu)
487{
488 void __iomem *mbase = mtu->mac_base;
489 struct mtu3_ep *ep_array;
490 int in_ep_num, out_ep_num;
491 u32 cap_epinfo;
492 int ret;
493 int i;
494
495 cap_epinfo = mtu3_readl(mbase, U3D_CAP_EPINFO);
496 in_ep_num = CAP_TX_EP_NUM(cap_epinfo);
497 out_ep_num = CAP_RX_EP_NUM(cap_epinfo);
498
499 dev_info(mtu->dev, "fifosz/epnum: Tx=%#x/%d, Rx=%#x/%d\n",
500 mtu3_readl(mbase, U3D_CAP_EPNTXFFSZ), in_ep_num,
501 mtu3_readl(mbase, U3D_CAP_EPNRXFFSZ), out_ep_num);
502
503
504 mtu->num_eps = min(in_ep_num, out_ep_num) + 1;
505 ep_array = kcalloc(mtu->num_eps * 2, sizeof(*ep_array), GFP_KERNEL);
506 if (ep_array == NULL)
507 return -ENOMEM;
508
509 mtu->ep_array = ep_array;
510 mtu->in_eps = ep_array;
511 mtu->out_eps = &ep_array[mtu->num_eps];
512
513 mtu->ep0 = mtu->in_eps;
514 mtu->ep0->mtu = mtu;
515 mtu->ep0->epnum = 0;
516
517 for (i = 1; i < mtu->num_eps; i++) {
518 struct mtu3_ep *mep = mtu->in_eps + i;
519
520 mep->fifo = &mtu->tx_fifo;
521 mep = mtu->out_eps + i;
522 mep->fifo = &mtu->rx_fifo;
523 }
524
525 get_ep_fifo_config(mtu);
526
527 ret = mtu3_qmu_init(mtu);
528 if (ret)
529 kfree(mtu->ep_array);
530
531 return ret;
532}
533
534static void mtu3_mem_free(struct mtu3 *mtu)
535{
536 mtu3_qmu_exit(mtu);
537 kfree(mtu->ep_array);
538}
539
540static void mtu3_set_speed(struct mtu3 *mtu)
541{
542 void __iomem *mbase = mtu->mac_base;
543
544 if (!mtu->is_u3_ip && (mtu->max_speed > USB_SPEED_HIGH))
545 mtu->max_speed = USB_SPEED_HIGH;
546
547 if (mtu->max_speed == USB_SPEED_FULL) {
548
549 mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
550
551 mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
552 } else if (mtu->max_speed == USB_SPEED_HIGH) {
553 mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
554
555 mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
556 } else if (mtu->max_speed == USB_SPEED_SUPER) {
557 mtu3_clrbits(mtu->ippc_base, SSUSB_U3_CTRL(0),
558 SSUSB_U3_PORT_SSP_SPEED);
559 }
560
561 dev_info(mtu->dev, "max_speed: %s\n",
562 usb_speed_string(mtu->max_speed));
563}
564
565static void mtu3_regs_init(struct mtu3 *mtu)
566{
567
568 void __iomem *mbase = mtu->mac_base;
569
570
571 mtu3_intr_disable(mtu);
572 mtu3_intr_status_clear(mtu);
573
574 if (mtu->is_u3_ip) {
575
576 mtu3_clrbits(mbase, U3D_LINK_POWER_CONTROL,
577 SW_U1_ACCEPT_ENABLE | SW_U2_ACCEPT_ENABLE |
578 SW_U1_REQUEST_ENABLE | SW_U2_REQUEST_ENABLE);
579
580 mtu3_clrbits(mbase, U3D_LTSSM_CTRL, SOFT_U3_EXIT_EN);
581
582 mtu3_setbits(mbase, U3D_USB2_TEST_MODE, U2U3_AUTO_SWITCH);
583 }
584
585 mtu3_set_speed(mtu);
586
587
588 mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
589
590 mtu3_writel(mbase, U3D_DEVICE_CONF, 0);
591
592 mtu3_setbits(mbase, U3D_QCR0, QMU_CS16B_EN);
593
594 mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
595}
596
597static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
598{
599 void __iomem *mbase = mtu->mac_base;
600 enum usb_device_speed udev_speed;
601 u32 maxpkt = 64;
602 u32 link;
603 u32 speed;
604
605 link = mtu3_readl(mbase, U3D_DEV_LINK_INTR);
606 link &= mtu3_readl(mbase, U3D_DEV_LINK_INTR_ENABLE);
607 mtu3_writel(mbase, U3D_DEV_LINK_INTR, link);
608 dev_dbg(mtu->dev, "=== LINK[%x] ===\n", link);
609
610 if (!(link & SSUSB_DEV_SPEED_CHG_INTR))
611 return IRQ_NONE;
612
613 speed = SSUSB_DEV_SPEED(mtu3_readl(mbase, U3D_DEVICE_CONF));
614
615 switch (speed) {
616 case MTU3_SPEED_FULL:
617 udev_speed = USB_SPEED_FULL;
618
619 mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
620 | LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
621 mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
622 LPM_BESL_STALL | LPM_BESLD_STALL);
623 break;
624 case MTU3_SPEED_HIGH:
625 udev_speed = USB_SPEED_HIGH;
626
627 mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
628 | LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
629 mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
630 LPM_BESL_STALL | LPM_BESLD_STALL);
631 break;
632 case MTU3_SPEED_SUPER:
633 udev_speed = USB_SPEED_SUPER;
634 maxpkt = 512;
635 break;
636 case MTU3_SPEED_SUPER_PLUS:
637 udev_speed = USB_SPEED_SUPER_PLUS;
638 maxpkt = 512;
639 break;
640 default:
641 udev_speed = USB_SPEED_UNKNOWN;
642 break;
643 }
644 dev_dbg(mtu->dev, "%s: %s\n", __func__, usb_speed_string(udev_speed));
645
646 mtu->g.speed = udev_speed;
647 mtu->g.ep0->maxpacket = maxpkt;
648 mtu->ep0_state = MU3D_EP0_STATE_SETUP;
649
650 if (udev_speed == USB_SPEED_UNKNOWN)
651 mtu3_gadget_disconnect(mtu);
652 else
653 mtu3_ep0_setup(mtu);
654
655 return IRQ_HANDLED;
656}
657
658static irqreturn_t mtu3_u3_ltssm_isr(struct mtu3 *mtu)
659{
660 void __iomem *mbase = mtu->mac_base;
661 u32 ltssm;
662
663 ltssm = mtu3_readl(mbase, U3D_LTSSM_INTR);
664 ltssm &= mtu3_readl(mbase, U3D_LTSSM_INTR_ENABLE);
665 mtu3_writel(mbase, U3D_LTSSM_INTR, ltssm);
666 dev_dbg(mtu->dev, "=== LTSSM[%x] ===\n", ltssm);
667
668 if (ltssm & (HOT_RST_INTR | WARM_RST_INTR))
669 mtu3_gadget_reset(mtu);
670
671 if (ltssm & VBUS_FALL_INTR) {
672 mtu3_ss_func_set(mtu, false);
673 mtu3_gadget_reset(mtu);
674 }
675
676 if (ltssm & VBUS_RISE_INTR)
677 mtu3_ss_func_set(mtu, true);
678
679 if (ltssm & EXIT_U3_INTR)
680 mtu3_gadget_resume(mtu);
681
682 if (ltssm & ENTER_U3_INTR)
683 mtu3_gadget_suspend(mtu);
684
685 return IRQ_HANDLED;
686}
687
688static irqreturn_t mtu3_u2_common_isr(struct mtu3 *mtu)
689{
690 void __iomem *mbase = mtu->mac_base;
691 u32 u2comm;
692
693 u2comm = mtu3_readl(mbase, U3D_COMMON_USB_INTR);
694 u2comm &= mtu3_readl(mbase, U3D_COMMON_USB_INTR_ENABLE);
695 mtu3_writel(mbase, U3D_COMMON_USB_INTR, u2comm);
696 dev_dbg(mtu->dev, "=== U2COMM[%x] ===\n", u2comm);
697
698 if (u2comm & SUSPEND_INTR)
699 mtu3_gadget_suspend(mtu);
700
701 if (u2comm & RESUME_INTR)
702 mtu3_gadget_resume(mtu);
703
704 if (u2comm & RESET_INTR)
705 mtu3_gadget_reset(mtu);
706
707 if (u2comm & LPM_RESUME_INTR) {
708 if (!(mtu3_readl(mbase, U3D_POWER_MANAGEMENT) & LPM_HRWE))
709 mtu3_setbits(mbase, U3D_USB20_MISC_CONTROL,
710 LPM_U3_ACK_EN);
711 }
712
713 return IRQ_HANDLED;
714}
715
716static irqreturn_t mtu3_irq(int irq, void *data)
717{
718 struct mtu3 *mtu = (struct mtu3 *)data;
719 unsigned long flags;
720 u32 level1;
721
722 spin_lock_irqsave(&mtu->lock, flags);
723
724
725 level1 = mtu3_readl(mtu->mac_base, U3D_LV1ISR);
726 level1 &= mtu3_readl(mtu->mac_base, U3D_LV1IER);
727
728 if (level1 & EP_CTRL_INTR)
729 mtu3_link_isr(mtu);
730
731 if (level1 & MAC2_INTR)
732 mtu3_u2_common_isr(mtu);
733
734 if (level1 & MAC3_INTR)
735 mtu3_u3_ltssm_isr(mtu);
736
737 if (level1 & BMU_INTR)
738 mtu3_ep0_isr(mtu);
739
740 if (level1 & QMU_INTR)
741 mtu3_qmu_isr(mtu);
742
743 spin_unlock_irqrestore(&mtu->lock, flags);
744
745 return IRQ_HANDLED;
746}
747
748static int mtu3_hw_init(struct mtu3 *mtu)
749{
750 u32 cap_dev;
751 int ret;
752
753 mtu->hw_version = mtu3_readl(mtu->ippc_base, U3D_SSUSB_HW_ID);
754
755 cap_dev = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_DEV_CAP);
756 mtu->is_u3_ip = !!SSUSB_IP_DEV_U3_PORT_NUM(cap_dev);
757
758 dev_info(mtu->dev, "IP version 0x%x(%s IP)\n", mtu->hw_version,
759 mtu->is_u3_ip ? "U3" : "U2");
760
761 mtu3_device_reset(mtu);
762
763 ret = mtu3_device_enable(mtu);
764 if (ret) {
765 dev_err(mtu->dev, "device enable failed %d\n", ret);
766 return ret;
767 }
768
769 ret = mtu3_mem_alloc(mtu);
770 if (ret)
771 return -ENOMEM;
772
773 mtu3_regs_init(mtu);
774
775 return 0;
776}
777
778static void mtu3_hw_exit(struct mtu3 *mtu)
779{
780 mtu3_device_disable(mtu);
781 mtu3_mem_free(mtu);
782}
783
784
785
786
787
788static int mtu3_set_dma_mask(struct mtu3 *mtu)
789{
790 struct device *dev = mtu->dev;
791 bool is_36bit = false;
792 int ret = 0;
793 u32 value;
794
795 value = mtu3_readl(mtu->mac_base, U3D_MISC_CTRL);
796 if (value & DMA_ADDR_36BIT) {
797 is_36bit = true;
798 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(36));
799
800 if (ret) {
801 is_36bit = false;
802 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
803 }
804 }
805 dev_info(dev, "dma mask: %s bits\n", is_36bit ? "36" : "32");
806
807 return ret;
808}
809
810int ssusb_gadget_init(struct ssusb_mtk *ssusb)
811{
812 struct device *dev = ssusb->dev;
813 struct platform_device *pdev = to_platform_device(dev);
814 struct mtu3 *mtu = NULL;
815 struct resource *res;
816 int ret = -ENOMEM;
817
818 mtu = devm_kzalloc(dev, sizeof(struct mtu3), GFP_KERNEL);
819 if (mtu == NULL)
820 return -ENOMEM;
821
822 mtu->irq = platform_get_irq(pdev, 0);
823 if (mtu->irq < 0) {
824 dev_err(dev, "fail to get irq number\n");
825 return mtu->irq;
826 }
827 dev_info(dev, "irq %d\n", mtu->irq);
828
829 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac");
830 mtu->mac_base = devm_ioremap_resource(dev, res);
831 if (IS_ERR(mtu->mac_base)) {
832 dev_err(dev, "error mapping memory for dev mac\n");
833 return PTR_ERR(mtu->mac_base);
834 }
835
836 spin_lock_init(&mtu->lock);
837 mtu->dev = dev;
838 mtu->ippc_base = ssusb->ippc_base;
839 ssusb->mac_base = mtu->mac_base;
840 ssusb->u3d = mtu;
841 mtu->ssusb = ssusb;
842 mtu->max_speed = usb_get_maximum_speed(dev);
843
844
845 switch (mtu->max_speed) {
846 case USB_SPEED_FULL:
847 case USB_SPEED_HIGH:
848 case USB_SPEED_SUPER:
849 case USB_SPEED_SUPER_PLUS:
850 break;
851 default:
852 dev_err(dev, "invalid max_speed: %s\n",
853 usb_speed_string(mtu->max_speed));
854
855 case USB_SPEED_UNKNOWN:
856
857 mtu->max_speed = USB_SPEED_SUPER_PLUS;
858 break;
859 }
860
861 dev_dbg(dev, "mac_base=0x%p, ippc_base=0x%p\n",
862 mtu->mac_base, mtu->ippc_base);
863
864 ret = mtu3_hw_init(mtu);
865 if (ret) {
866 dev_err(dev, "mtu3 hw init failed:%d\n", ret);
867 return ret;
868 }
869
870 ret = mtu3_set_dma_mask(mtu);
871 if (ret) {
872 dev_err(dev, "mtu3 set dma_mask failed:%d\n", ret);
873 goto dma_mask_err;
874 }
875
876 ret = devm_request_irq(dev, mtu->irq, mtu3_irq, 0, dev_name(dev), mtu);
877 if (ret) {
878 dev_err(dev, "request irq %d failed!\n", mtu->irq);
879 goto irq_err;
880 }
881
882 device_init_wakeup(dev, true);
883
884 ret = mtu3_gadget_setup(mtu);
885 if (ret) {
886 dev_err(dev, "mtu3 gadget init failed:%d\n", ret);
887 goto gadget_err;
888 }
889
890
891 if (mtu->ssusb->dr_mode == USB_DR_MODE_OTG)
892 mtu3_stop(mtu);
893
894 dev_dbg(dev, " %s() done...\n", __func__);
895
896 return 0;
897
898gadget_err:
899 device_init_wakeup(dev, false);
900
901dma_mask_err:
902irq_err:
903 mtu3_hw_exit(mtu);
904 ssusb->u3d = NULL;
905 dev_err(dev, " %s() fail...\n", __func__);
906
907 return ret;
908}
909
910void ssusb_gadget_exit(struct ssusb_mtk *ssusb)
911{
912 struct mtu3 *mtu = ssusb->u3d;
913
914 mtu3_gadget_cleanup(mtu);
915 device_init_wakeup(ssusb->dev, false);
916 mtu3_hw_exit(mtu);
917}
918
