LXR linux/drivers/net/wireless/broadcom/b43/Kconfig

   1config B43
   2        tristate "Broadcom 43xx wireless support (mac80211 stack)"
   3        depends on (BCMA_POSSIBLE || SSB_POSSIBLE) && MAC80211 && HAS_DMA
   4        select BCMA if B43_BCMA
   5        select SSB if B43_SSB
   6        select FW_LOADER
   7        help
   8          b43 is a driver for the Broadcom 43xx series wireless devices.
   9
  10          Check "lspci" for something like
  11          "Broadcom Corporation BCM43XX 802.11 Wireless LAN Controller"
  12          to determine whether you own such a device.
  13
  14          This driver supports the new BCM43xx IEEE 802.11G devices, but not
  15          the old IEEE 802.11B devices. Old devices are supported by
  16          the b43legacy driver.
  17          Note that this has nothing to do with the standard that your AccessPoint
  18          supports (A, B, G or a combination).
  19          IEEE 802.11G devices can talk to IEEE 802.11B AccessPoints.
  20
  21          It is safe to include both b43 and b43legacy as the underlying glue
  22          layer will automatically load the correct version for your device.
  23
  24          This driver uses V4 firmware, which must be installed separately using
  25          b43-fwcutter.
  26
  27          This driver can be built as a module (recommended) that will be called "b43".
  28          If unsure, say M.
  29
  30config B43_BCMA
  31        bool
  32
  33config B43_SSB
  34        bool
  35
  36choice
  37        prompt "Supported bus types"
  38        depends on B43
  39        default B43_BUSES_BCMA_AND_SSB
  40
  41config B43_BUSES_BCMA_AND_SSB
  42        bool "BCMA and SSB"
  43        depends on BCMA_POSSIBLE && SSB_POSSIBLE
  44        select B43_BCMA
  45        select B43_SSB
  46
  47config B43_BUSES_BCMA
  48        bool "BCMA only"
  49        depends on BCMA_POSSIBLE
  50        select B43_BCMA
  51
  52config B43_BUSES_SSB
  53        bool "SSB only"
  54        depends on SSB_POSSIBLE
  55        select B43_SSB
  56
  57endchoice
  58
  59# Auto-select SSB PCI-HOST support, if possible
  60config B43_PCI_AUTOSELECT
  61        bool
  62        depends on B43 && SSB_PCIHOST_POSSIBLE
  63        select SSB_PCIHOST
  64        select SSB_B43_PCI_BRIDGE
  65        default y
  66
  67# Auto-select SSB PCICORE driver, if possible
  68config B43_PCICORE_AUTOSELECT
  69        bool
  70        depends on B43 && SSB_DRIVER_PCICORE_POSSIBLE
  71        select SSB_DRIVER_PCICORE
  72        default y
  73
  74config B43_SDIO
  75        bool "Broadcom 43xx SDIO device support"
  76        depends on B43 && B43_SSB && SSB_SDIOHOST_POSSIBLE
  77        select SSB_SDIOHOST
  78        help
  79          Broadcom 43xx device support for Soft-MAC SDIO devices.
  80
  81          With this config option you can drive Soft-MAC b43 cards with a
  82          Secure Digital I/O interface.
  83          This includes the WLAN daughter card found on the Nintendo Wii
  84          video game console.
  85          Note that this does not support Broadcom 43xx Full-MAC devices.
  86
  87          It's safe to select Y here, even if you don't have a B43 SDIO device.
  88
  89          If unsure, say N.
  90
  91#Data transfers to the device via PIO. We want it as a fallback even
  92# if we can do DMA.
  93config B43_BCMA_PIO
  94        bool
  95        depends on B43 && B43_BCMA
  96        select BCMA_BLOCKIO
  97        default y
  98
  99config B43_PIO
 100        bool
 101        depends on B43 && B43_SSB
 102        select SSB_BLOCKIO
 103        default y
 104
 105config B43_PHY_G
 106        bool "Support for G-PHY (802.11g) devices"
 107        depends on B43 && B43_SSB
 108        default y
 109        help
 110          This PHY type can be found in the following chipsets:
 111          PCI: BCM4306, BCM4311, BCM4318
 112          SoC: BCM4712, BCM5352E
 113
 114config B43_PHY_N
 115        bool "Support for N-PHY (the main 802.11n series) devices"
 116        depends on B43
 117        default y
 118        help
 119          This PHY type can be found in the following chipsets:
 120          PCI: BCM4321, BCM4322,
 121               BCM43222, BCM43224, BCM43225,
 122               BCM43131, BCM43217, BCM43227, BCM43228
 123          SoC: BCM4716, BCM4717, BCM4718, BCM5356, BCM5357, BCM5358
 124
 125config B43_PHY_LP
 126        bool "Support for LP-PHY (low-power 802.11g) devices"
 127        depends on B43 && B43_SSB
 128        default y
 129        help
 130          The LP-PHY is a low-power PHY built into some notebooks
 131          and embedded devices. It supports 802.11a/b/g
 132          (802.11a support is optional, and currently disabled).
 133
 134config B43_PHY_HT
 135        bool "Support for HT-PHY (high throughput 802.11n) devices"
 136        depends on B43 && B43_BCMA
 137        default y
 138        help
 139          This PHY type with 3x3:3 MIMO can be found in the BCM4331 PCI chipset.
 140
 141config B43_PHY_LCN
 142        bool "Support for LCN-PHY devices (BROKEN)"
 143        depends on B43 && BROKEN
 144        help
 145          Support for the LCN-PHY.
 146
 147          Say N, this is BROKEN and crashes driver.
 148
 149config B43_PHY_AC
 150        bool "Support for AC-PHY (802.11ac) devices (BROKEN)"
 151        depends on B43 && B43_BCMA && BROKEN
 152        help
 153          This PHY type can be found in the following chipsets:
 154          PCI: BCM4352, BCM4360
 155
 156          Say N, this is BROKEN and crashes driver.
 157
 158# This config option automatically enables b43 LEDS support,
 159# if it's possible.
 160config B43_LEDS
 161        bool
 162        depends on B43 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = B43)
 163        default y
 164
 165# This config option automatically enables b43 HW-RNG support,
 166# if the HW-RNG core is enabled.
 167config B43_HWRNG
 168        bool
 169        depends on B43 && (HW_RANDOM = y || HW_RANDOM = B43)
 170        default y
 171
 172config B43_DEBUG
 173        bool "Broadcom 43xx debugging"
 174        depends on B43
 175        help
 176          Broadcom 43xx debugging.
 177
 178          This adds additional runtime sanity checks and statistics to the driver.
 179          These checks and statistics might be expensive and hurt the runtime
 180          performance of your system.
 181          This also adds the b43 debugfs interface.
 182
 183          Do not enable this, unless you are debugging the driver.
 184
 185          Say N, if you are a distributor or user building a release kernel
 186          for production use.
 187          Only say Y, if you are debugging a problem in the b43 driver sourcecode.
 188