LXR linux/drivers/usb/dwc3/dwc3-st.c

   1// SPDX-License-Identifier: GPL-2.0+
   2/**
   3 * dwc3-st.c Support for dwc3 platform devices on ST Microelectronics platforms
   4 *
   5 * This is a small driver for the dwc3 to provide the glue logic
   6 * to configure the controller. Tested on STi platforms.
   7 *
   8 * Copyright (C) 2014 Stmicroelectronics
   9 *
  10 * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
  11 * Contributors: Aymen Bouattay <aymen.bouattay@st.com>
  12 *               Peter Griffin <peter.griffin@linaro.org>
  13 *
  14 * Inspired by dwc3-omap.c and dwc3-exynos.c.
  15 */
  16
  17#include <linux/delay.h>
  18#include <linux/interrupt.h>
  19#include <linux/io.h>
  20#include <linux/ioport.h>
  21#include <linux/kernel.h>
  22#include <linux/mfd/syscon.h>
  23#include <linux/module.h>
  24#include <linux/of.h>
  25#include <linux/of_platform.h>
  26#include <linux/platform_device.h>
  27#include <linux/slab.h>
  28#include <linux/regmap.h>
  29#include <linux/reset.h>
  30#include <linux/pinctrl/consumer.h>
  31#include <linux/usb/of.h>
  32
  33#include "core.h"
  34#include "io.h"
  35
  36/* glue registers */
  37#define CLKRST_CTRL             0x00
  38#define AUX_CLK_EN              BIT(0)
  39#define SW_PIPEW_RESET_N        BIT(4)
  40#define EXT_CFG_RESET_N         BIT(8)
  41/*
  42 * 1'b0 : The host controller complies with the xHCI revision 0.96
  43 * 1'b1 : The host controller complies with the xHCI revision 1.0
  44 */
  45#define XHCI_REVISION           BIT(12)
  46
  47#define USB2_VBUS_MNGMNT_SEL1   0x2C
  48/*
  49 * For all fields in USB2_VBUS_MNGMNT_SEL1
  50 * 2’b00 : Override value from Reg 0x30 is selected
  51 * 2’b01 : utmiotg_<signal_name> from usb3_top is selected
  52 * 2’b10 : pipew_<signal_name> from PIPEW instance is selected
  53 * 2’b11 : value is 1'b0
  54 */
  55#define USB2_VBUS_REG30         0x0
  56#define USB2_VBUS_UTMIOTG       0x1
  57#define USB2_VBUS_PIPEW         0x2
  58#define USB2_VBUS_ZERO          0x3
  59
  60#define SEL_OVERRIDE_VBUSVALID(n)       (n << 0)
  61#define SEL_OVERRIDE_POWERPRESENT(n)    (n << 4)
  62#define SEL_OVERRIDE_BVALID(n)          (n << 8)
  63
  64/* Static DRD configuration */
  65#define USB3_CONTROL_MASK               0xf77
  66
  67#define USB3_DEVICE_NOT_HOST            BIT(0)
  68#define USB3_FORCE_VBUSVALID            BIT(1)
  69#define USB3_DELAY_VBUSVALID            BIT(2)
  70#define USB3_SEL_FORCE_OPMODE           BIT(4)
  71#define USB3_FORCE_OPMODE(n)            (n << 5)
  72#define USB3_SEL_FORCE_DPPULLDOWN2      BIT(8)
  73#define USB3_FORCE_DPPULLDOWN2          BIT(9)
  74#define USB3_SEL_FORCE_DMPULLDOWN2      BIT(10)
  75#define USB3_FORCE_DMPULLDOWN2          BIT(11)
  76
  77/**
  78 * struct st_dwc3 - dwc3-st driver private structure
  79 * @dev:                device pointer
  80 * @glue_base:          ioaddr for the glue registers
  81 * @regmap:             regmap pointer for getting syscfg
  82 * @syscfg_reg_off:     usb syscfg control offset
  83 * @dr_mode:            drd static host/device config
  84 * @rstc_pwrdn:         rest controller for powerdown signal
  85 * @rstc_rst:           reset controller for softreset signal
  86 */
  87
  88struct st_dwc3 {
  89        struct device *dev;
  90        void __iomem *glue_base;
  91        struct regmap *regmap;
  92        int syscfg_reg_off;
  93        enum usb_dr_mode dr_mode;
  94        struct reset_control *rstc_pwrdn;
  95        struct reset_control *rstc_rst;
  96};
  97
  98static inline u32 st_dwc3_readl(void __iomem *base, u32 offset)
  99{
 100        return readl_relaxed(base + offset);
 101}
 102
 103static inline void st_dwc3_writel(void __iomem *base, u32 offset, u32 value)
 104{
 105        writel_relaxed(value, base + offset);
 106}
 107
 108/**
 109 * st_dwc3_drd_init: program the port
 110 * @dwc3_data: driver private structure
 111 * Description: this function is to program the port as either host or device
 112 * according to the static configuration passed from devicetree.
 113 * OTG and dual role are not yet supported!
 114 */
 115static int st_dwc3_drd_init(struct st_dwc3 *dwc3_data)
 116{
 117        u32 val;
 118        int err;
 119
 120        err = regmap_read(dwc3_data->regmap, dwc3_data->syscfg_reg_off, &val);
 121        if (err)
 122                return err;
 123
 124        val &= USB3_CONTROL_MASK;
 125
 126        switch (dwc3_data->dr_mode) {
 127        case USB_DR_MODE_PERIPHERAL:
 128
 129                val &= ~(USB3_DELAY_VBUSVALID
 130                        | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
 131                        | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
 132                        | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
 133
 134                /*
 135                 * USB3_PORT2_FORCE_VBUSVALID When '1' and when
 136                 * USB3_PORT2_DEVICE_NOT_HOST = 1, forces VBUSVLDEXT2 input
 137                 * of the pico PHY to 1.
 138                 */
 139
 140                val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID;
 141                break;
 142
 143        case USB_DR_MODE_HOST:
 144
 145                val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
 146                        | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
 147                        | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
 148                        | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
 149
 150                /*
 151                 * USB3_DELAY_VBUSVALID is ANDed with USB_C_VBUSVALID. Thus,
 152                 * when set to ‘0‘, it can delay the arrival of VBUSVALID
 153                 * information to VBUSVLDEXT2 input of the pico PHY.
 154                 * We don't want to do that so we set the bit to '1'.
 155                 */
 156
 157                val |= USB3_DELAY_VBUSVALID;
 158                break;
 159
 160        default:
 161                dev_err(dwc3_data->dev, "Unsupported mode of operation %d\n",
 162                        dwc3_data->dr_mode);
 163                return -EINVAL;
 164        }
 165
 166        return regmap_write(dwc3_data->regmap, dwc3_data->syscfg_reg_off, val);
 167}
 168
 169/**
 170 * st_dwc3_init: init the controller via glue logic
 171 * @dwc3_data: driver private structure
 172 */
 173static void st_dwc3_init(struct st_dwc3 *dwc3_data)
 174{
 175        u32 reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
 176
 177        reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
 178        reg &= ~SW_PIPEW_RESET_N;
 179        st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
 180
 181        /* configure mux for vbus, powerpresent and bvalid signals */
 182        reg = st_dwc3_readl(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1);
 183
 184        reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
 185                SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
 186                SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
 187
 188        st_dwc3_writel(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1, reg);
 189
 190        reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
 191        reg |= SW_PIPEW_RESET_N;
 192        st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
 193}
 194
 195static int st_dwc3_probe(struct platform_device *pdev)
 196{
 197        struct st_dwc3 *dwc3_data;
 198        struct resource *res;
 199        struct device *dev = &pdev->dev;
 200        struct device_node *node = dev->of_node, *child;
 201        struct platform_device *child_pdev;
 202        struct regmap *regmap;
 203        int ret;
 204
 205        dwc3_data = devm_kzalloc(dev, sizeof(*dwc3_data), GFP_KERNEL);
 206        if (!dwc3_data)
 207                return -ENOMEM;
 208
 209        dwc3_data->glue_base =
 210                devm_platform_ioremap_resource_byname(pdev, "reg-glue");
 211        if (IS_ERR(dwc3_data->glue_base))
 212                return PTR_ERR(dwc3_data->glue_base);
 213
 214        regmap = syscon_regmap_lookup_by_phandle(node, "st,syscfg");
 215        if (IS_ERR(regmap))
 216                return PTR_ERR(regmap);
 217
 218        dwc3_data->dev = dev;
 219        dwc3_data->regmap = regmap;
 220
 221        res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "syscfg-reg");
 222        if (!res) {
 223                ret = -ENXIO;
 224                goto undo_platform_dev_alloc;
 225        }
 226
 227        dwc3_data->syscfg_reg_off = res->start;
 228
 229        dev_vdbg(&pdev->dev, "glue-logic addr 0x%pK, syscfg-reg offset 0x%x\n",
 230                 dwc3_data->glue_base, dwc3_data->syscfg_reg_off);
 231
 232        dwc3_data->rstc_pwrdn =
 233                devm_reset_control_get_exclusive(dev, "powerdown");
 234        if (IS_ERR(dwc3_data->rstc_pwrdn)) {
 235                dev_err(&pdev->dev, "could not get power controller\n");
 236                ret = PTR_ERR(dwc3_data->rstc_pwrdn);
 237                goto undo_platform_dev_alloc;
 238        }
 239
 240        /* Manage PowerDown */
 241        reset_control_deassert(dwc3_data->rstc_pwrdn);
 242
 243        dwc3_data->rstc_rst =
 244                devm_reset_control_get_shared(dev, "softreset");
 245        if (IS_ERR(dwc3_data->rstc_rst)) {
 246                dev_err(&pdev->dev, "could not get reset controller\n");
 247                ret = PTR_ERR(dwc3_data->rstc_rst);
 248                goto undo_powerdown;
 249        }
 250
 251        /* Manage SoftReset */
 252        reset_control_deassert(dwc3_data->rstc_rst);
 253
 254        child = of_get_child_by_name(node, "dwc3");
 255        if (!child) {
 256                dev_err(&pdev->dev, "failed to find dwc3 core node\n");
 257                ret = -ENODEV;
 258                goto err_node_put;
 259        }
 260
 261        /* Allocate and initialize the core */
 262        ret = of_platform_populate(node, NULL, NULL, dev);
 263        if (ret) {
 264                dev_err(dev, "failed to add dwc3 core\n");
 265                goto err_node_put;
 266        }
 267
 268        child_pdev = of_find_device_by_node(child);
 269        if (!child_pdev) {
 270                dev_err(dev, "failed to find dwc3 core device\n");
 271                ret = -ENODEV;
 272                goto err_node_put;
 273        }
 274
 275        dwc3_data->dr_mode = usb_get_dr_mode(&child_pdev->dev);
 276        of_node_put(child);
 277        of_dev_put(child_pdev);
 278
 279        /*
 280         * Configure the USB port as device or host according to the static
 281         * configuration passed from DT.
 282         * DRD is the only mode currently supported so this will be enhanced
 283         * as soon as OTG is available.
 284         */
 285        ret = st_dwc3_drd_init(dwc3_data);
 286        if (ret) {
 287                dev_err(dev, "drd initialisation failed\n");
 288                goto undo_softreset;
 289        }
 290
 291        /* ST glue logic init */
 292        st_dwc3_init(dwc3_data);
 293
 294        platform_set_drvdata(pdev, dwc3_data);
 295        return 0;
 296
 297err_node_put:
 298        of_node_put(child);
 299undo_softreset:
 300        reset_control_assert(dwc3_data->rstc_rst);
 301undo_powerdown:
 302        reset_control_assert(dwc3_data->rstc_pwrdn);
 303undo_platform_dev_alloc:
 304        platform_device_put(pdev);
 305        return ret;
 306}
 307
 308static int st_dwc3_remove(struct platform_device *pdev)
 309{
 310        struct st_dwc3 *dwc3_data = platform_get_drvdata(pdev);
 311
 312        of_platform_depopulate(&pdev->dev);
 313
 314        reset_control_assert(dwc3_data->rstc_pwrdn);
 315        reset_control_assert(dwc3_data->rstc_rst);
 316
 317        return 0;
 318}
 319
 320#ifdef CONFIG_PM_SLEEP
 321static int st_dwc3_suspend(struct device *dev)
 322{
 323        struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
 324
 325        reset_control_assert(dwc3_data->rstc_pwrdn);
 326        reset_control_assert(dwc3_data->rstc_rst);
 327
 328        pinctrl_pm_select_sleep_state(dev);
 329
 330        return 0;
 331}
 332
 333static int st_dwc3_resume(struct device *dev)
 334{
 335        struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
 336        int ret;
 337
 338        pinctrl_pm_select_default_state(dev);
 339
 340        reset_control_deassert(dwc3_data->rstc_pwrdn);
 341        reset_control_deassert(dwc3_data->rstc_rst);
 342
 343        ret = st_dwc3_drd_init(dwc3_data);
 344        if (ret) {
 345                dev_err(dev, "drd initialisation failed\n");
 346                return ret;
 347        }
 348
 349        /* ST glue logic init */
 350        st_dwc3_init(dwc3_data);
 351
 352        return 0;
 353}
 354#endif /* CONFIG_PM_SLEEP */
 355
 356static SIMPLE_DEV_PM_OPS(st_dwc3_dev_pm_ops, st_dwc3_suspend, st_dwc3_resume);
 357
 358static const struct of_device_id st_dwc3_match[] = {
 359        { .compatible = "st,stih407-dwc3" },
 360        { /* sentinel */ },
 361};
 362
 363MODULE_DEVICE_TABLE(of, st_dwc3_match);
 364
 365static struct platform_driver st_dwc3_driver = {
 366        .probe = st_dwc3_probe,
 367        .remove = st_dwc3_remove,
 368        .driver = {
 369                .name = "usb-st-dwc3",
 370                .of_match_table = st_dwc3_match,
 371                .pm = &st_dwc3_dev_pm_ops,
 372        },
 373};
 374
 375module_platform_driver(st_dwc3_driver);
 376
 377MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
 378MODULE_DESCRIPTION("DesignWare USB3 STi Glue Layer");
 379MODULE_LICENSE("GPL v2");
 380