1/* SPDX-License-Identifier: GPL-2.0 */ 2/*************************************************************************** 3 * * 4 * Copyright (c) 2000-2008 LSI Corporation. All rights reserved. * 5 * * 6 * Description * 7 * ------------ * 8 * This include file contains SAS firmware interface IOC Log Info codes * 9 * * 10 *-------------------------------------------------------------------------* 11 */ 12 13#ifndef IOPI_IOCLOGINFO_H_INCLUDED 14#define IOPI_IOCLOGINFO_H_INCLUDED 15 16#define SAS_LOGINFO_NEXUS_LOSS 0x31170000 17#define SAS_LOGINFO_MASK 0xFFFF0000 18 19/****************************************************************************/ 20/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */ 21/* Format: */ 22/* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */ 23/* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */ 24/* Bits 23-16: LOGINFO_CODE */ 25/* Bits 15-0: LOGINFO_CODE Specific */ 26/****************************************************************************/ 27 28/****************************************************************************/ 29/* IOC_LOGINFO_ORIGINATOR defines */ 30/****************************************************************************/ 31#define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000) 32#define IOC_LOGINFO_ORIGINATOR_PL (0x01000000) 33#define IOC_LOGINFO_ORIGINATOR_IR (0x02000000) 34 35#define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000) 36 37/****************************************************************************/ 38/* LOGINFO_CODE defines */ 39/****************************************************************************/ 40#define IOC_LOGINFO_CODE_MASK (0x00FF0000) 41#define IOC_LOGINFO_CODE_SHIFT (16) 42 43/****************************************************************************/ 44/* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */ 45/****************************************************************************/ 46#define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000) 47#define IOP_LOGINFO_CODE_UNUSED2 (0x00020000) 48#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000) 49#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */ 50#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */ 51#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */ 52#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */ 53#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */ 54#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */ 55#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */ 56 57#define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */ 58#define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */ 59#define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */ 60#define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occurred while attempting to upload the entire flash */ 61#define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occurred while attempting to upload single flash region */ 62#define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occurred while DMAing FW to host memory */ 63 64#define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */ 65 66#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000) 67 68#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */ 69#define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */ 70 71#define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001) 72#define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002) 73#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003) 74#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004) 75#define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005) 76 77#define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT (0x00080000) 78 79/****************************************************************************/ 80/* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */ 81/****************************************************************************/ 82#define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */ 83 84#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT (0x00000001) 85#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED (0x00000002) 86#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0 (0x00000003) 87#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1 (0x00000004) 88#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0 (0x00000005) 89#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1 (0x00000006) 90#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0 (0x00000007) 91#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1 (0x00000008) 92#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY (0x00000009) 93#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK (0x0000000A) 94#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B (0x0000000B) 95#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C) 96#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D) 97#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E) 98#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST (0x00000011) 99#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012) 100#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013) 101#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014) 102#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1 (0x00000015) 103#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2 (0x00000016) 104#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3 (0x00000017) 105#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY (0x00000018) 106#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION (0x00000019) 107 108#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED (0x0000001B) /* Retry Timeout */ 109#define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED (0x0000001C) /* Retry Timeout */ 110 111 112 113#define PL_LOGINFO_CODE_INVALID_SGL (0x00020000) 114#define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000) 115#define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000) 116#define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000) 117#define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000) 118#define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000) 119#define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000) 120#define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000) 121#define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000) 122#define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000) 123#define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000) 124#define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000) 125#define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000) 126#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000) 127#define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */ 128#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */ 129#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */ 130#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */ 131#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */ 132#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */ 133#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */ 134#define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */ 135#define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000) 136#define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */ 137#define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE)*/ 138#define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000) 139#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000) 140#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000) 141#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000) 142#define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000) 143#define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR (0x00180000) 144#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100) 145#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101) 146#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI (0x00000102) 147#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED (0x00000103) 148#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK (0x00000104) 149#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION (0x00000114) 150#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0 (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */ 151#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1 (0x00000115) 152#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2 (0x00000116) 153#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3 (0x00000117) 154#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */ 155#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED (0x0000011B) 156#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */ 157 158#define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120) 159#define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */ 160#define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */ 161 162 163#define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200) 164#define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300) 165#define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) 166/* Bits 0-3 encode Transport Status Register (offset 0x08) */ 167/* Bit 0 is Status Bit 0: FrameXferErr */ 168/* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ 169/* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */ 170 171#define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500) 172#define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600) 173#define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700) 174#define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800) 175#define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900) 176#define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00) 177#define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00) 178#define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00) 179#define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00) 180#define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00) 181#define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01) 182#define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00) 183#define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000) 184#define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION (0x00002000) 185/* not currently used in mainline */ 186#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK (0x00003000) 187#define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP (0x00004000) 188#define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD (0x00005000) 189 190#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */ 191#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occurred on SMP Read */ 192#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occurred on SMP Write */ 193#define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */ 194#define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */ 195#define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */ 196#define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */ 197#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */ 198#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */ 199#define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */ 200#define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */ 201#define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */ 202#define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */ 203#define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */ 204 205#define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */ 206#define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */ 207#define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */ 208#define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */ 209#define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */ 210#define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */ 211#define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transferring data */ 212#define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transferring sense data */ 213#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */ 214#define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */ 215#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */ 216#define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/ 217#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */ 218#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2 (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */ 219#define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3 (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */ 220 221 222/****************************************************************************/ 223/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */ 224/****************************************************************************/ 225#define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000) 226#define IR_LOGINFO_CODE_UNUSED2 (0x00020000) 227 228/* Amount of information passed down for Create Volume is too large */ 229#define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001) 230/* Creation of duplicate volume attempted (Bus/Target ID checked) */ 231#define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002) 232/* Creation failed due to maximum number of supported volumes exceeded */ 233#define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003) 234/* Creation failed due to DMA error in trying to read from host */ 235#define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004) 236/* Creation failed due to invalid volume type passed down */ 237#define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005) 238/* Creation failed due to error reading MFG Page 4 */ 239#define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006) 240/* Creation failed when trying to create internal structures */ 241#define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007) 242 243/* Activation failed due to trying to activate an already active volume */ 244#define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010) 245/* Activation failed due to trying to active unsupported volume type */ 246#define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011) 247/* Activation failed due to trying to active too many volumes */ 248#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012) 249/* Activation failed due to Volume ID in use already */ 250#define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013) 251/* Activation failed call to activateVolume returned failure */ 252#define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014) 253/* Activation failed trying to import the volume */ 254#define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015) 255/* Activation failed trying to import the volume */ 256#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS (0x00010016) 257 258/* Phys Disk failed, too many phys disks */ 259#define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020) 260/* Amount of information passed down for Create Pnysdisk is too large */ 261#define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021) 262/* Creation failed due to DMA error in trying to read from host */ 263#define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022) 264/* Creation failed due to invalid Bus TargetID passed down */ 265#define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023) 266/* Creation failed due to error in creating RAID Phys Disk Config Page */ 267#define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024) 268 269 270/* Compatibility Error : IR Disabled */ 271#define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030) 272/* Compatibility Error : Inquiry Command failed */ 273#define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031) 274/* Compatibility Error : Device not direct access device */ 275#define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032) 276/* Compatibility Error : Removable device found */ 277#define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033) 278/* Compatibility Error : Device SCSI Version not 2 or higher */ 279#define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034) 280/* Compatibility Error : SATA device, 48 BIT LBA not supported */ 281#define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035) 282/* Compatibility Error : Device does not have 512 byte block sizes */ 283#define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036) 284/* Compatibility Error : Volume Type check failed */ 285#define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037) 286/* Compatibility Error : Volume Type is unsupported by FW */ 287#define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038) 288/* Compatibility Error : Disk drive too small for use in volume */ 289#define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039) 290/* Compatibility Error : Phys disk for Create Volume not found */ 291#define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A) 292/* Compatibility Error : membership count error, too many or too few disks for volume type */ 293#define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B) 294/* Compatibility Error : Disk stripe sizes must be 64KB */ 295#define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C) 296/* Compatibility Error : IME size limited to < 2TB */ 297#define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D) 298 299/* Device Firmware Update: DFU can only be started once */ 300#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS (0x00010050) 301/* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */ 302#define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE (0x00010051) 303/* Device Firmware Update: DFU Timeout cannot be zero */ 304#define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT (0x00010052) 305/* Device Firmware Update: CREATE TIMER FAILED */ 306#define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS (0x00010053) 307/* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */ 308#define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE (0x00010054) 309/* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */ 310#define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED (0x00010055) 311/* Device Firmware Update: Unable to allocate memory for page */ 312#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE (0x00010056) 313 314 315/****************************************************************************/ 316/* Defines for convenience */ 317/****************************************************************************/ 318#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP) 319#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL) 320#define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR) 321 322#endif /* end of file */ 323 324