1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23#include <linux/types.h>
24#include <linux/init.h>
25#include <linux/mm.h>
26#include <linux/module.h>
27#include <linux/platform_device.h>
28#include <linux/spi/spi.h>
29#include <linux/gpio_keys.h>
30#include <linux/input.h>
31
32#include <asm/setup.h>
33#include <asm/mach-types.h>
34#include <asm/irq.h>
35
36#include <asm/mach/arch.h>
37#include <asm/mach/map.h>
38#include <asm/mach/irq.h>
39
40#include <mach/hardware.h>
41#include <mach/board.h>
42#include <mach/gpio.h>
43#include <mach/at91sam9_smc.h>
44#include <mach/at91_shdwc.h>
45
46#include "sam9_smc.h"
47#include "generic.h"
48
49
50static void __init ek_map_io(void)
51{
52
53 at91sam9263_initialize(12000000);
54
55
56 at91_register_uart(0, 0, 0);
57
58
59 at91_set_serial_console(0);
60}
61
62static void __init ek_init_irq(void)
63{
64 at91sam9263_init_interrupts(NULL);
65}
66
67
68
69
70
71static struct at91_usbh_data __initdata ek_usbh_data = {
72 .ports = 2,
73};
74
75
76
77
78static struct at91_udc_data __initdata ek_udc_data = {
79 .vbus_pin = AT91_PIN_PB11,
80 .pullup_pin = 0,
81};
82
83
84
85
86static struct spi_board_info ek_spi_devices[] = {
87#if !defined(CONFIG_MMC_AT91)
88 {
89 .modalias = "mtd_dataflash",
90 .chip_select = 0,
91 .max_speed_hz = 15 * 1000 * 1000,
92 .bus_num = 0,
93 }
94#endif
95};
96
97
98
99
100static struct at91_eth_data __initdata ek_macb_data = {
101 .phy_irq_pin = AT91_PIN_PE31,
102 .is_rmii = 1,
103};
104
105
106
107
108static struct mtd_partition __initdata ek_nand_partition[] = {
109 {
110 .name = "Linux Kernel",
111 .offset = 0,
112 .size = SZ_16M,
113 },
114 {
115 .name = "Root FS",
116 .offset = MTDPART_OFS_NXTBLK,
117 .size = 120 * SZ_1M,
118 },
119 {
120 .name = "FS",
121 .offset = MTDPART_OFS_NXTBLK,
122 .size = 120 * SZ_1M,
123 }
124};
125
126static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
127{
128 *num_partitions = ARRAY_SIZE(ek_nand_partition);
129 return ek_nand_partition;
130}
131
132static struct atmel_nand_data __initdata ek_nand_data = {
133 .ale = 21,
134 .cle = 22,
135
136 .rdy_pin = AT91_PIN_PA22,
137 .enable_pin = AT91_PIN_PD15,
138 .partition_info = nand_partitions,
139};
140
141static struct sam9_smc_config __initdata ek_nand_smc_config = {
142 .ncs_read_setup = 0,
143 .nrd_setup = 1,
144 .ncs_write_setup = 0,
145 .nwe_setup = 1,
146
147 .ncs_read_pulse = 3,
148 .nrd_pulse = 3,
149 .ncs_write_pulse = 3,
150 .nwe_pulse = 3,
151
152 .read_cycle = 5,
153 .write_cycle = 5,
154
155 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
156 .tdf_cycles = 2,
157};
158
159static void __init ek_add_device_nand(void)
160{
161
162 sam9_smc_configure(3, &ek_nand_smc_config);
163
164 at91_add_device_nand(&ek_nand_data);
165}
166
167
168
169
170
171#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
172static struct gpio_keys_button ek_buttons[] = {
173 {
174 .code = KEY_ENTER,
175 .gpio = AT91_PIN_PB10,
176 .active_low = 1,
177 .desc = "user_pb",
178 .wakeup = 1,
179 }
180};
181
182static struct gpio_keys_platform_data ek_button_data = {
183 .buttons = ek_buttons,
184 .nbuttons = ARRAY_SIZE(ek_buttons),
185};
186
187static struct platform_device ek_button_device = {
188 .name = "gpio-keys",
189 .id = -1,
190 .num_resources = 0,
191 .dev = {
192 .platform_data = &ek_button_data,
193 }
194};
195
196static void __init ek_add_device_buttons(void)
197{
198 at91_set_GPIO_periph(AT91_PIN_PB10, 1);
199 at91_set_deglitch(AT91_PIN_PB10, 1);
200
201 platform_device_register(&ek_button_device);
202}
203#else
204static void __init ek_add_device_buttons(void) {}
205#endif
206
207
208
209
210static struct gpio_led ek_leds[] = {
211 {
212 .name = "user_led",
213 .gpio = AT91_PIN_PB21,
214 .active_low = 1,
215 .default_trigger = "heartbeat",
216 }
217};
218
219
220static void __init ek_board_init(void)
221{
222
223 at91_add_device_serial();
224
225 at91_add_device_usbh(&ek_usbh_data);
226
227 at91_add_device_udc(&ek_udc_data);
228
229 at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
230
231 at91_add_device_eth(&ek_macb_data);
232
233 ek_add_device_nand();
234
235 at91_add_device_i2c(NULL, 0);
236
237 ek_add_device_buttons();
238
239 at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
240
241 at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
242 | AT91_SHDW_RTTWKEN);
243}
244
245MACHINE_START(USB_A9263, "CALAO USB_A9263")
246
247 .phys_io = AT91_BASE_SYS,
248 .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
249 .boot_params = AT91_SDRAM_BASE + 0x100,
250 .timer = &at91sam926x_timer,
251 .map_io = ek_map_io,
252 .init_irq = ek_init_irq,
253 .init_machine = ek_board_init,
254MACHINE_END
255
