linux/arch/arm/mach-omap2/board-h4.c
<<
>>
Prefs
   1/*
   2 * linux/arch/arm/mach-omap2/board-h4.c
   3 *
   4 * Copyright (C) 2005 Nokia Corporation
   5 * Author: Paul Mundt <paul.mundt@nokia.com>
   6 *
   7 * Modified from mach-omap/omap1/board-generic.c
   8 *
   9 * This program is free software; you can redistribute it and/or modify
  10 * it under the terms of the GNU General Public License version 2 as
  11 * published by the Free Software Foundation.
  12 */
  13
  14#include <linux/kernel.h>
  15#include <linux/init.h>
  16#include <linux/platform_device.h>
  17#include <linux/mtd/mtd.h>
  18#include <linux/mtd/partitions.h>
  19#include <linux/delay.h>
  20#include <linux/workqueue.h>
  21#include <linux/i2c.h>
  22#include <linux/i2c/at24.h>
  23#include <linux/input.h>
  24#include <linux/err.h>
  25#include <linux/clk.h>
  26#include <linux/io.h>
  27
  28#include <mach/hardware.h>
  29#include <asm/mach-types.h>
  30#include <asm/mach/arch.h>
  31#include <asm/mach/map.h>
  32#include <asm/mach/flash.h>
  33
  34#include <mach/control.h>
  35#include <mach/gpio.h>
  36#include <mach/mux.h>
  37#include <mach/usb.h>
  38#include <mach/board.h>
  39#include <mach/common.h>
  40#include <mach/keypad.h>
  41#include <mach/menelaus.h>
  42#include <mach/dma.h>
  43#include <mach/gpmc.h>
  44
  45#define H4_FLASH_CS     0
  46#define H4_SMC91X_CS    1
  47
  48#define H4_ETHR_GPIO_IRQ                92
  49
  50static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
  51static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
  52
  53static int h4_keymap[] = {
  54        KEY(0, 0, KEY_LEFT),
  55        KEY(0, 1, KEY_RIGHT),
  56        KEY(0, 2, KEY_A),
  57        KEY(0, 3, KEY_B),
  58        KEY(0, 4, KEY_C),
  59        KEY(1, 0, KEY_DOWN),
  60        KEY(1, 1, KEY_UP),
  61        KEY(1, 2, KEY_E),
  62        KEY(1, 3, KEY_F),
  63        KEY(1, 4, KEY_G),
  64        KEY(2, 0, KEY_ENTER),
  65        KEY(2, 1, KEY_I),
  66        KEY(2, 2, KEY_J),
  67        KEY(2, 3, KEY_K),
  68        KEY(2, 4, KEY_3),
  69        KEY(3, 0, KEY_M),
  70        KEY(3, 1, KEY_N),
  71        KEY(3, 2, KEY_O),
  72        KEY(3, 3, KEY_P),
  73        KEY(3, 4, KEY_Q),
  74        KEY(4, 0, KEY_R),
  75        KEY(4, 1, KEY_4),
  76        KEY(4, 2, KEY_T),
  77        KEY(4, 3, KEY_U),
  78        KEY(4, 4, KEY_ENTER),
  79        KEY(5, 0, KEY_V),
  80        KEY(5, 1, KEY_W),
  81        KEY(5, 2, KEY_L),
  82        KEY(5, 3, KEY_S),
  83        KEY(5, 4, KEY_ENTER),
  84        0
  85};
  86
  87static struct mtd_partition h4_partitions[] = {
  88        /* bootloader (U-Boot, etc) in first sector */
  89        {
  90              .name             = "bootloader",
  91              .offset           = 0,
  92              .size             = SZ_128K,
  93              .mask_flags       = MTD_WRITEABLE, /* force read-only */
  94        },
  95        /* bootloader params in the next sector */
  96        {
  97              .name             = "params",
  98              .offset           = MTDPART_OFS_APPEND,
  99              .size             = SZ_128K,
 100              .mask_flags       = 0,
 101        },
 102        /* kernel */
 103        {
 104              .name             = "kernel",
 105              .offset           = MTDPART_OFS_APPEND,
 106              .size             = SZ_2M,
 107              .mask_flags       = 0
 108        },
 109        /* file system */
 110        {
 111              .name             = "filesystem",
 112              .offset           = MTDPART_OFS_APPEND,
 113              .size             = MTDPART_SIZ_FULL,
 114              .mask_flags       = 0
 115        }
 116};
 117
 118static struct flash_platform_data h4_flash_data = {
 119        .map_name       = "cfi_probe",
 120        .width          = 2,
 121        .parts          = h4_partitions,
 122        .nr_parts       = ARRAY_SIZE(h4_partitions),
 123};
 124
 125static struct resource h4_flash_resource = {
 126        .flags          = IORESOURCE_MEM,
 127};
 128
 129static struct platform_device h4_flash_device = {
 130        .name           = "omapflash",
 131        .id             = 0,
 132        .dev            = {
 133                .platform_data  = &h4_flash_data,
 134        },
 135        .num_resources  = 1,
 136        .resource       = &h4_flash_resource,
 137};
 138
 139static struct omap_kp_platform_data h4_kp_data = {
 140        .rows           = 6,
 141        .cols           = 7,
 142        .keymap         = h4_keymap,
 143        .keymapsize     = ARRAY_SIZE(h4_keymap),
 144        .rep            = 1,
 145        .row_gpios      = row_gpios,
 146        .col_gpios      = col_gpios,
 147};
 148
 149static struct platform_device h4_kp_device = {
 150        .name           = "omap-keypad",
 151        .id             = -1,
 152        .dev            = {
 153                .platform_data = &h4_kp_data,
 154        },
 155};
 156
 157static struct platform_device h4_lcd_device = {
 158        .name           = "lcd_h4",
 159        .id             = -1,
 160};
 161
 162static struct platform_device *h4_devices[] __initdata = {
 163        &h4_flash_device,
 164        &h4_kp_device,
 165        &h4_lcd_device,
 166};
 167
 168/* 2420 Sysboot setup (2430 is different) */
 169static u32 get_sysboot_value(void)
 170{
 171        return (omap_ctrl_readl(OMAP24XX_CONTROL_STATUS) &
 172                (OMAP2_SYSBOOT_5_MASK | OMAP2_SYSBOOT_4_MASK |
 173                 OMAP2_SYSBOOT_3_MASK | OMAP2_SYSBOOT_2_MASK |
 174                 OMAP2_SYSBOOT_1_MASK | OMAP2_SYSBOOT_0_MASK));
 175}
 176
 177/* H4-2420's always used muxed mode, H4-2422's always use non-muxed
 178 *
 179 * Note: OMAP-GIT doesn't correctly do is_cpu_omap2422 and is_cpu_omap2423
 180 *  correctly.  The macro needs to look at production_id not just hawkeye.
 181 */
 182static u32 is_gpmc_muxed(void)
 183{
 184        u32 mux;
 185        mux = get_sysboot_value();
 186        if ((mux & 0xF) == 0xd)
 187                return 1;       /* NAND config (could be either) */
 188        if (mux & 0x2)          /* if mux'ed */
 189                return 1;
 190        else
 191                return 0;
 192}
 193
 194static inline void __init h4_init_debug(void)
 195{
 196        int eth_cs;
 197        unsigned long cs_mem_base;
 198        unsigned int muxed, rate;
 199        struct clk *gpmc_fck;
 200
 201        eth_cs  = H4_SMC91X_CS;
 202
 203        gpmc_fck = clk_get(NULL, "gpmc_fck");   /* Always on ENABLE_ON_INIT */
 204        if (IS_ERR(gpmc_fck)) {
 205                WARN_ON(1);
 206                return;
 207        }
 208
 209        clk_enable(gpmc_fck);
 210        rate = clk_get_rate(gpmc_fck);
 211        clk_disable(gpmc_fck);
 212        clk_put(gpmc_fck);
 213
 214        if (is_gpmc_muxed())
 215                muxed = 0x200;
 216        else
 217                muxed = 0;
 218
 219        /* Make sure CS1 timings are correct */
 220        gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
 221                          0x00011000 | muxed);
 222
 223        if (rate >= 160000000) {
 224                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
 225                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
 226                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
 227                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
 228                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
 229        } else if (rate >= 130000000) {
 230                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
 231                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
 232                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
 233                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
 234                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
 235        } else {/* rate = 100000000 */
 236                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
 237                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
 238                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
 239                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
 240                gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
 241        }
 242
 243        if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
 244                printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
 245                goto out;
 246        }
 247
 248        udelay(100);
 249
 250        omap_cfg_reg(M15_24XX_GPIO92);
 251        if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
 252                gpmc_cs_free(eth_cs);
 253
 254out:
 255        clk_disable(gpmc_fck);
 256        clk_put(gpmc_fck);
 257}
 258
 259static void __init h4_init_flash(void)
 260{
 261        unsigned long base;
 262
 263        if (gpmc_cs_request(H4_FLASH_CS, SZ_64M, &base) < 0) {
 264                printk("Can't request GPMC CS for flash\n");
 265                return;
 266        }
 267        h4_flash_resource.start = base;
 268        h4_flash_resource.end   = base + SZ_64M - 1;
 269}
 270
 271static struct omap_lcd_config h4_lcd_config __initdata = {
 272        .ctrl_name      = "internal",
 273};
 274
 275static struct omap_usb_config h4_usb_config __initdata = {
 276#ifdef  CONFIG_MACH_OMAP2_H4_USB1
 277        /* NOTE:  usb1 could also be used with 3 wire signaling */
 278        .pins[1]        = 4,
 279#endif
 280
 281#ifdef  CONFIG_MACH_OMAP_H4_OTG
 282        /* S1.10 ON -- USB OTG port
 283         * usb0 switched to Mini-AB port and isp1301 transceiver;
 284         * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging
 285         */
 286        .otg            = 1,
 287        .pins[0]        = 4,
 288#ifdef  CONFIG_USB_GADGET_OMAP
 289        /* use OTG cable, or standard A-to-MiniB */
 290        .hmc_mode       = 0x14, /* 0:dev/otg 1:host 2:disable */
 291#elif   defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 292        /* use OTG cable, or NONSTANDARD (B-to-MiniB) */
 293        .hmc_mode       = 0x11, /* 0:host 1:host 2:disable */
 294#endif  /* XX */
 295
 296#else
 297        /* S1.10 OFF -- usb "download port"
 298         * usb0 switched to Mini-B port and isp1105 transceiver;
 299         * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
 300         */
 301        .register_dev   = 1,
 302        .pins[0]        = 3,
 303/*      .hmc_mode       = 0x14,*/       /* 0:dev 1:host 2:disable */
 304        .hmc_mode       = 0x00,         /* 0:dev|otg 1:disable 2:disable */
 305#endif
 306};
 307
 308static struct omap_board_config_kernel h4_config[] = {
 309        { OMAP_TAG_LCD,         &h4_lcd_config },
 310};
 311
 312static void __init omap_h4_init_irq(void)
 313{
 314        omap_board_config = h4_config;
 315        omap_board_config_size = ARRAY_SIZE(h4_config);
 316        omap2_init_common_hw(NULL, NULL);
 317        omap_init_irq();
 318        omap_gpio_init();
 319        h4_init_flash();
 320}
 321
 322static struct at24_platform_data m24c01 = {
 323        .byte_len       = SZ_1K / 8,
 324        .page_size      = 16,
 325};
 326
 327static struct i2c_board_info __initdata h4_i2c_board_info[] = {
 328        {
 329                I2C_BOARD_INFO("isp1301_omap", 0x2d),
 330                .irq            = OMAP_GPIO_IRQ(125),
 331        },
 332        {       /* EEPROM on mainboard */
 333                I2C_BOARD_INFO("24c01", 0x52),
 334                .platform_data  = &m24c01,
 335        },
 336        {       /* EEPROM on cpu card */
 337                I2C_BOARD_INFO("24c01", 0x57),
 338                .platform_data  = &m24c01,
 339        },
 340};
 341
 342static void __init omap_h4_init(void)
 343{
 344        /*
 345         * Make sure the serial ports are muxed on at this point.
 346         * You have to mux them off in device drivers later on
 347         * if not needed.
 348         */
 349#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
 350        omap_cfg_reg(K15_24XX_UART3_TX);
 351        omap_cfg_reg(K14_24XX_UART3_RX);
 352#endif
 353
 354#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
 355        if (omap_has_menelaus()) {
 356                row_gpios[5] = 0;
 357                col_gpios[2] = 15;
 358                col_gpios[6] = 18;
 359        }
 360#endif
 361
 362        i2c_register_board_info(1, h4_i2c_board_info,
 363                        ARRAY_SIZE(h4_i2c_board_info));
 364
 365        platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
 366        omap_usb_init(&h4_usb_config);
 367        omap_serial_init();
 368}
 369
 370static void __init omap_h4_map_io(void)
 371{
 372        omap2_set_globals_242x();
 373        omap2_map_common_io();
 374}
 375
 376MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
 377        /* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
 378        .phys_io        = 0x48000000,
 379        .io_pg_offst    = ((0xd8000000) >> 18) & 0xfffc,
 380        .boot_params    = 0x80000100,
 381        .map_io         = omap_h4_map_io,
 382        .init_irq       = omap_h4_init_irq,
 383        .init_machine   = omap_h4_init,
 384        .timer          = &omap_timer,
 385MACHINE_END
 386