linux/arch/blackfin/mach-bf533/boards/cm_bf533.c
<<
>>
Prefs
   1/*
   2 * Copyright 2004-2009 Analog Devices Inc.
   3 *           2008-2009 Bluetechnix
   4 *                2005 National ICT Australia (NICTA)
   5 *                      Aidan Williams <aidan@nicta.com.au>
   6 *
   7 * Licensed under the GPL-2 or later.
   8 */
   9
  10#include <linux/device.h>
  11#include <linux/platform_device.h>
  12#include <linux/mtd/mtd.h>
  13#include <linux/mtd/partitions.h>
  14#include <linux/mtd/physmap.h>
  15#include <linux/spi/spi.h>
  16#include <linux/spi/flash.h>
  17#include <linux/spi/mmc_spi.h>
  18#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  19#include <linux/usb/isp1362.h>
  20#endif
  21#include <linux/irq.h>
  22#include <asm/dma.h>
  23#include <asm/bfin5xx_spi.h>
  24#include <asm/portmux.h>
  25#include <asm/dpmc.h>
  26
  27/*
  28 * Name the Board for the /proc/cpuinfo
  29 */
  30const char bfin_board_name[] = "Bluetechnix CM BF533";
  31
  32#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
  33/* all SPI peripherals info goes here */
  34#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
  35static struct mtd_partition bfin_spi_flash_partitions[] = {
  36        {
  37                .name = "bootloader(spi)",
  38                .size = 0x00020000,
  39                .offset = 0,
  40                .mask_flags = MTD_CAP_ROM
  41        }, {
  42                .name = "linux kernel(spi)",
  43                .size = 0xe0000,
  44                .offset = 0x20000
  45        }, {
  46                .name = "file system(spi)",
  47                .size = 0x700000,
  48                .offset = 0x00100000,
  49        }
  50};
  51
  52static struct flash_platform_data bfin_spi_flash_data = {
  53        .name = "m25p80",
  54        .parts = bfin_spi_flash_partitions,
  55        .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
  56        .type = "m25p64",
  57};
  58
  59/* SPI flash chip (m25p64) */
  60static struct bfin5xx_spi_chip spi_flash_chip_info = {
  61        .enable_dma = 0,         /* use dma transfer with this chip*/
  62        .bits_per_word = 8,
  63};
  64#endif
  65
  66/* SPI ADC chip */
  67#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
  68static struct bfin5xx_spi_chip spi_adc_chip_info = {
  69        .enable_dma = 1,         /* use dma transfer with this chip*/
  70        .bits_per_word = 16,
  71};
  72#endif
  73
  74#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
  75static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
  76        .enable_dma = 0,
  77        .bits_per_word = 16,
  78};
  79#endif
  80
  81#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
  82static struct bfin5xx_spi_chip mmc_spi_chip_info = {
  83        .enable_dma = 0,
  84        .bits_per_word = 8,
  85};
  86#endif
  87
  88static struct spi_board_info bfin_spi_board_info[] __initdata = {
  89#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
  90        {
  91                /* the modalias must be the same as spi device driver name */
  92                .modalias = "m25p80",       /* Name of spi_driver for this device */
  93                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
  94                .bus_num = 0,               /* Framework bus number */
  95                .chip_select = 1,           /* Framework chip select. On STAMP537 it is SPISSEL1*/
  96                .platform_data = &bfin_spi_flash_data,
  97                .controller_data = &spi_flash_chip_info,
  98                .mode = SPI_MODE_3,
  99        },
 100#endif
 101
 102#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 103        {
 104                .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 105                .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 106                .bus_num = 0,               /* Framework bus number */
 107                .chip_select = 2,           /* Framework chip select. */
 108                .platform_data = NULL,      /* No spi_driver specific config */
 109                .controller_data = &spi_adc_chip_info,
 110        },
 111#endif
 112
 113#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 114        {
 115                .modalias = "ad1836",
 116                .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 117                .bus_num = 0,
 118                .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
 119                .controller_data = &ad1836_spi_chip_info,
 120        },
 121#endif
 122
 123#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 124        {
 125                .modalias = "mmc_spi",
 126                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 127                .bus_num = 0,
 128                .chip_select = 1,
 129                .controller_data = &mmc_spi_chip_info,
 130                .mode = SPI_MODE_3,
 131        },
 132#endif
 133};
 134
 135/* SPI (0) */
 136static struct resource bfin_spi0_resource[] = {
 137        [0] = {
 138                .start = SPI0_REGBASE,
 139                .end   = SPI0_REGBASE + 0xFF,
 140                .flags = IORESOURCE_MEM,
 141        },
 142        [1] = {
 143                .start = CH_SPI,
 144                .end   = CH_SPI,
 145                .flags = IORESOURCE_DMA,
 146        },
 147        [2] = {
 148                .start = IRQ_SPI,
 149                .end   = IRQ_SPI,
 150                .flags = IORESOURCE_IRQ,
 151        }
 152};
 153
 154/* SPI controller data */
 155static struct bfin5xx_spi_master bfin_spi0_info = {
 156        .num_chipselect = 8,
 157        .enable_dma = 1,  /* master has the ability to do dma transfer */
 158        .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 159};
 160
 161static struct platform_device bfin_spi0_device = {
 162        .name = "bfin-spi",
 163        .id = 0, /* Bus number */
 164        .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 165        .resource = bfin_spi0_resource,
 166        .dev = {
 167                .platform_data = &bfin_spi0_info, /* Passed to driver */
 168        },
 169};
 170#endif  /* spi master and devices */
 171
 172#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 173static struct platform_device rtc_device = {
 174        .name = "rtc-bfin",
 175        .id   = -1,
 176};
 177#endif
 178
 179#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 180#include <linux/smc91x.h>
 181
 182static struct smc91x_platdata smc91x_info = {
 183        .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 184        .leda = RPC_LED_100_10,
 185        .ledb = RPC_LED_TX_RX,
 186};
 187
 188static struct resource smc91x_resources[] = {
 189        {
 190                .start = 0x20200300,
 191                .end = 0x20200300 + 16,
 192                .flags = IORESOURCE_MEM,
 193        }, {
 194                .start = IRQ_PF0,
 195                .end = IRQ_PF0,
 196                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 197        },
 198};
 199static struct platform_device smc91x_device = {
 200        .name = "smc91x",
 201        .id = 0,
 202        .num_resources = ARRAY_SIZE(smc91x_resources),
 203        .resource = smc91x_resources,
 204        .dev    = {
 205                .platform_data  = &smc91x_info,
 206        },
 207};
 208#endif
 209
 210#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 211#include <linux/smsc911x.h>
 212
 213static struct resource smsc911x_resources[] = {
 214        {
 215                .name = "smsc911x-memory",
 216                .start = 0x20308000,
 217                .end = 0x20308000 + 0xFF,
 218                .flags = IORESOURCE_MEM,
 219        }, {
 220                .start = IRQ_PF8,
 221                .end = IRQ_PF8,
 222                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 223        },
 224};
 225
 226static struct smsc911x_platform_config smsc911x_config = {
 227        .flags = SMSC911X_USE_16BIT,
 228        .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
 229        .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
 230        .phy_interface = PHY_INTERFACE_MODE_MII,
 231};
 232
 233static struct platform_device smsc911x_device = {
 234        .name = "smsc911x",
 235        .id = 0,
 236        .num_resources = ARRAY_SIZE(smsc911x_resources),
 237        .resource = smsc911x_resources,
 238        .dev = {
 239                .platform_data = &smsc911x_config,
 240        },
 241};
 242#endif
 243
 244#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 245static struct resource bfin_uart_resources[] = {
 246        {
 247                .start = 0xFFC00400,
 248                .end = 0xFFC004FF,
 249                .flags = IORESOURCE_MEM,
 250        },
 251};
 252
 253static struct platform_device bfin_uart_device = {
 254        .name = "bfin-uart",
 255        .id = 1,
 256        .num_resources = ARRAY_SIZE(bfin_uart_resources),
 257        .resource = bfin_uart_resources,
 258};
 259#endif
 260
 261#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 262#ifdef CONFIG_BFIN_SIR0
 263static struct resource bfin_sir0_resources[] = {
 264        {
 265                .start = 0xFFC00400,
 266                .end = 0xFFC004FF,
 267                .flags = IORESOURCE_MEM,
 268        },
 269        {
 270                .start = IRQ_UART0_RX,
 271                .end = IRQ_UART0_RX+1,
 272                .flags = IORESOURCE_IRQ,
 273        },
 274        {
 275                .start = CH_UART0_RX,
 276                .end = CH_UART0_RX+1,
 277                .flags = IORESOURCE_DMA,
 278        },
 279};
 280
 281static struct platform_device bfin_sir0_device = {
 282        .name = "bfin_sir",
 283        .id = 0,
 284        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 285        .resource = bfin_sir0_resources,
 286};
 287#endif
 288#endif
 289
 290#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 291static struct platform_device bfin_sport0_uart_device = {
 292        .name = "bfin-sport-uart",
 293        .id = 0,
 294};
 295
 296static struct platform_device bfin_sport1_uart_device = {
 297        .name = "bfin-sport-uart",
 298        .id = 1,
 299};
 300#endif
 301
 302#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 303static struct resource isp1362_hcd_resources[] = {
 304        {
 305                .start = 0x20308000,
 306                .end = 0x20308000,
 307                .flags = IORESOURCE_MEM,
 308        }, {
 309                .start = 0x20308004,
 310                .end = 0x20308004,
 311                .flags = IORESOURCE_MEM,
 312        }, {
 313                .start = IRQ_PF4,
 314                .end = IRQ_PF4,
 315                .flags = IORESOURCE_IRQ,
 316        },
 317};
 318
 319static struct isp1362_platform_data isp1362_priv = {
 320        .sel15Kres = 1,
 321        .clknotstop = 0,
 322        .oc_enable = 0,
 323        .int_act_high = 0,
 324        .int_edge_triggered = 0,
 325        .remote_wakeup_connected = 0,
 326        .no_power_switching = 1,
 327        .power_switching_mode = 0,
 328};
 329
 330static struct platform_device isp1362_hcd_device = {
 331        .name = "isp1362-hcd",
 332        .id = 0,
 333        .dev = {
 334                .platform_data = &isp1362_priv,
 335        },
 336        .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 337        .resource = isp1362_hcd_resources,
 338};
 339#endif
 340
 341
 342#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 343static struct resource net2272_bfin_resources[] = {
 344        {
 345                .start = 0x20300000,
 346                .end = 0x20300000 + 0x100,
 347                .flags = IORESOURCE_MEM,
 348        }, {
 349                .start = IRQ_PF6,
 350                .end = IRQ_PF6,
 351                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 352        },
 353};
 354
 355static struct platform_device net2272_bfin_device = {
 356        .name = "net2272",
 357        .id = -1,
 358        .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 359        .resource = net2272_bfin_resources,
 360};
 361#endif
 362
 363
 364
 365#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 366static struct mtd_partition para_partitions[] = {
 367        {
 368                .name       = "bootloader(nor)",
 369                .size       = 0x40000,
 370                .offset     = 0,
 371        }, {
 372                .name       = "linux+rootfs(nor)",
 373                .size       = MTDPART_SIZ_FULL,
 374                .offset     = MTDPART_OFS_APPEND,
 375        },
 376};
 377
 378static struct physmap_flash_data para_flash_data = {
 379        .width      = 2,
 380        .parts      = para_partitions,
 381        .nr_parts   = ARRAY_SIZE(para_partitions),
 382};
 383
 384static struct resource para_flash_resource = {
 385        .start = 0x20000000,
 386        .end   = 0x201fffff,
 387        .flags = IORESOURCE_MEM,
 388};
 389
 390static struct platform_device para_flash_device = {
 391        .name          = "physmap-flash",
 392        .id            = 0,
 393        .dev = {
 394                .platform_data = &para_flash_data,
 395        },
 396        .num_resources = 1,
 397        .resource      = &para_flash_resource,
 398};
 399#endif
 400
 401
 402
 403static const unsigned int cclk_vlev_datasheet[] =
 404{
 405        VRPAIR(VLEV_085, 250000000),
 406        VRPAIR(VLEV_090, 376000000),
 407        VRPAIR(VLEV_095, 426000000),
 408        VRPAIR(VLEV_100, 426000000),
 409        VRPAIR(VLEV_105, 476000000),
 410        VRPAIR(VLEV_110, 476000000),
 411        VRPAIR(VLEV_115, 476000000),
 412        VRPAIR(VLEV_120, 600000000),
 413        VRPAIR(VLEV_125, 600000000),
 414        VRPAIR(VLEV_130, 600000000),
 415};
 416
 417static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 418        .tuple_tab = cclk_vlev_datasheet,
 419        .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 420        .vr_settling_time = 25 /* us */,
 421};
 422
 423static struct platform_device bfin_dpmc = {
 424        .name = "bfin dpmc",
 425        .dev = {
 426                .platform_data = &bfin_dmpc_vreg_data,
 427        },
 428};
 429
 430static struct platform_device *cm_bf533_devices[] __initdata = {
 431
 432        &bfin_dpmc,
 433
 434#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 435        &bfin_uart_device,
 436#endif
 437
 438#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 439#ifdef CONFIG_BFIN_SIR0
 440        &bfin_sir0_device,
 441#endif
 442#endif
 443
 444#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 445        &bfin_sport0_uart_device,
 446        &bfin_sport1_uart_device,
 447#endif
 448
 449#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 450        &rtc_device,
 451#endif
 452
 453#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 454        &isp1362_hcd_device,
 455#endif
 456
 457#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 458        &smc91x_device,
 459#endif
 460
 461#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 462        &smsc911x_device,
 463#endif
 464
 465#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 466        &net2272_bfin_device,
 467#endif
 468
 469#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 470        &bfin_spi0_device,
 471#endif
 472
 473#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 474        &para_flash_device,
 475#endif
 476};
 477
 478static int __init cm_bf533_init(void)
 479{
 480        printk(KERN_INFO "%s(): registering device resources\n", __func__);
 481        platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices));
 482#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 483        spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 484#endif
 485        return 0;
 486}
 487
 488arch_initcall(cm_bf533_init);
 489