LXR linux/arch/mips/nxp/pnx8550/common/setup.c

   1/*
   2 *
   3 * 2.6 port, Embedded Alley Solutions, Inc
   4 *
   5 *  Based on Per Hallsmark, per.hallsmark@mvista.com
   6 *
   7 *  This program is free software; you can distribute it and/or modify it
   8 *  under the terms of the GNU General Public License (Version 2) as
   9 *  published by the Free Software Foundation.
  10 *
  11 *  This program is distributed in the hope it will be useful, but WITHOUT
  12 *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  13 *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
  14 *  for more details.
  15 *
  16 *  You should have received a copy of the GNU General Public License along
  17 *  with this program; if not, write to the Free Software Foundation, Inc.,
  18 *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
  19 */
  20#include <linux/init.h>
  21#include <linux/sched.h>
  22#include <linux/ioport.h>
  23#include <linux/irq.h>
  24#include <linux/mm.h>
  25#include <linux/delay.h>
  26#include <linux/interrupt.h>
  27#include <linux/serial_pnx8xxx.h>
  28#include <linux/pm.h>
  29
  30#include <asm/cpu.h>
  31#include <asm/bootinfo.h>
  32#include <asm/irq.h>
  33#include <asm/mipsregs.h>
  34#include <asm/reboot.h>
  35#include <asm/pgtable.h>
  36#include <asm/time.h>
  37
  38#include <glb.h>
  39#include <int.h>
  40#include <pci.h>
  41#include <uart.h>
  42#include <nand.h>
  43
  44extern void __init board_setup(void);
  45extern void pnx8550_machine_restart(char *);
  46extern void pnx8550_machine_halt(void);
  47extern void pnx8550_machine_power_off(void);
  48extern struct resource ioport_resource;
  49extern struct resource iomem_resource;
  50extern char *prom_getcmdline(void);
  51
  52struct resource standard_io_resources[] = {
  53        {
  54                .start  = 0x00,
  55                .end    = 0x1f,
  56                .name   = "dma1",
  57                .flags  = IORESOURCE_BUSY
  58        }, {
  59                .start  = 0x40,
  60                .end    = 0x5f,
  61                .name   = "timer",
  62                .flags  = IORESOURCE_BUSY
  63        }, {
  64                .start  = 0x80,
  65                .end    = 0x8f,
  66                .name   = "dma page reg",
  67                .flags  = IORESOURCE_BUSY
  68        }, {
  69                .start  = 0xc0,
  70                .end    = 0xdf,
  71                .name   = "dma2",
  72                .flags  = IORESOURCE_BUSY
  73        },
  74};
  75
  76#define STANDARD_IO_RESOURCES ARRAY_SIZE(standard_io_resources)
  77
  78extern struct resource pci_io_resource;
  79extern struct resource pci_mem_resource;
  80
  81/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
  82unsigned long get_system_mem_size(void)
  83{
  84        /* Read IP2031_RANK0_ADDR_LO */
  85        unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
  86        /* Read IP2031_RANK1_ADDR_HI */
  87        unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
  88
  89        return dram_r1_hi - dram_r0_lo + 1;
  90}
  91
  92int pnx8550_console_port = -1;
  93
  94void __init plat_mem_setup(void)
  95{
  96        int i;
  97        char* argptr;
  98
  99        board_setup();  /* board specific setup */
 100
 101        _machine_restart = pnx8550_machine_restart;
 102        _machine_halt = pnx8550_machine_halt;
 103        pm_power_off = pnx8550_machine_power_off;
 104
 105        /* Clear the Global 2 Register, PCI Inta Output Enable Registers
 106           Bit 1:Enable DAC Powerdown
 107          -> 0:DACs are enabled and are working normally
 108             1:DACs are powerdown
 109           Bit 0:Enable of PCI inta output
 110          -> 0 = Disable PCI inta output
 111             1 = Enable PCI inta output
 112        */
 113        PNX8550_GLB2_ENAB_INTA_O = 0;
 114
 115        /* IO/MEM resources. */
 116        set_io_port_base(KSEG1);
 117        ioport_resource.start = 0;
 118        ioport_resource.end = ~0;
 119        iomem_resource.start = 0;
 120        iomem_resource.end = ~0;
 121
 122        /* Request I/O space for devices on this board */
 123        for (i = 0; i < STANDARD_IO_RESOURCES; i++)
 124                request_resource(&ioport_resource, standard_io_resources + i);
 125
 126        /* Place the Mode Control bit for GPIO pin 16 in primary function */
 127        /* Pin 16 is used by UART1, UA1_TX                                */
 128        outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
 129                        (PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
 130                        PNX8550_GPIO_MC1);
 131
 132        argptr = prom_getcmdline();
 133        if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
 134                argptr += strlen("console=ttyS");
 135                pnx8550_console_port = *argptr == '0' ? 0 : 1;
 136
 137                /* We must initialize the UART (console) before early printk */
 138                /* Set LCR to 8-bit and BAUD to 38400 (no 5)                */
 139                ip3106_lcr(UART_BASE, pnx8550_console_port) =
 140                        PNX8XXX_UART_LCR_8BIT;
 141                ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
 142        }
 143
 144        return;
 145}
 146