1/* Definitions for DigiBoard ditty(1) command. */ 2 3#if !defined(TIOCMODG) 4#define TIOCMODG (('d'<<8) | 250) /* get modem ctrl state */ 5#define TIOCMODS (('d'<<8) | 251) /* set modem ctrl state */ 6#endif 7 8#if !defined(TIOCMSET) 9#define TIOCMSET (('d'<<8) | 252) /* set modem ctrl state */ 10#define TIOCMGET (('d'<<8) | 253) /* set modem ctrl state */ 11#endif 12 13#if !defined(TIOCMBIC) 14#define TIOCMBIC (('d'<<8) | 254) /* set modem ctrl state */ 15#define TIOCMBIS (('d'<<8) | 255) /* set modem ctrl state */ 16#endif 17 18#if !defined(TIOCSDTR) 19#define TIOCSDTR (('e'<<8) | 0) /* set DTR */ 20#define TIOCCDTR (('e'<<8) | 1) /* clear DTR */ 21#endif 22 23/************************************************************************ 24 * Ioctl command arguments for DIGI parameters. 25 ************************************************************************/ 26#define DIGI_GETA (('e'<<8) | 94) /* Read params */ 27 28#define DIGI_SETA (('e'<<8) | 95) /* Set params */ 29#define DIGI_SETAW (('e'<<8) | 96) /* Drain & set params */ 30#define DIGI_SETAF (('e'<<8) | 97) /* Drain, flush & set params */ 31 32#define DIGI_GETFLOW (('e'<<8) | 99) /* Get startc/stopc flow */ 33 /* control characters */ 34#define DIGI_SETFLOW (('e'<<8) | 100) /* Set startc/stopc flow */ 35 /* control characters */ 36#define DIGI_GETAFLOW (('e'<<8) | 101) /* Get Aux. startc/stopc */ 37 /* flow control chars */ 38#define DIGI_SETAFLOW (('e'<<8) | 102) /* Set Aux. startc/stopc */ 39 /* flow control chars */ 40 41#define DIGI_GETINFO (('e'<<8) | 103) /* Fill in digi_info */ 42#define DIGI_POLLER (('e'<<8) | 104) /* Turn on/off poller */ 43#define DIGI_INIT (('e'<<8) | 105) /* Allow things to run. */ 44 45struct digiflow_struct 46{ 47 unsigned char startc; /* flow cntl start char */ 48 unsigned char stopc; /* flow cntl stop char */ 49}; 50 51typedef struct digiflow_struct digiflow_t; 52 53 54/************************************************************************ 55 * Values for digi_flags 56 ************************************************************************/ 57#define DIGI_IXON 0x0001 /* Handle IXON in the FEP */ 58#define DIGI_FAST 0x0002 /* Fast baud rates */ 59#define RTSPACE 0x0004 /* RTS input flow control */ 60#define CTSPACE 0x0008 /* CTS output flow control */ 61#define DSRPACE 0x0010 /* DSR output flow control */ 62#define DCDPACE 0x0020 /* DCD output flow control */ 63#define DTRPACE 0x0040 /* DTR input flow control */ 64#define DIGI_FORCEDCD 0x0100 /* Force carrier */ 65#define DIGI_ALTPIN 0x0200 /* Alternate RJ-45 pin config */ 66#define DIGI_AIXON 0x0400 /* Aux flow control in fep */ 67 68 69/************************************************************************ 70 * Values for digiDload 71 ************************************************************************/ 72#define NORMAL 0 73#define PCI_CTL 1 74 75#define SIZE8 0 76#define SIZE16 1 77#define SIZE32 2 78 79/************************************************************************ 80 * Structure used with ioctl commands for DIGI parameters. 81 ************************************************************************/ 82struct digi_struct 83{ 84 unsigned short digi_flags; /* Flags (see above) */ 85}; 86 87typedef struct digi_struct digi_t; 88 89struct digi_info 90{ 91 unsigned long board; /* Which board is this ? */ 92 unsigned char status; /* Alive or dead */ 93 unsigned char type; /* see epca.h */ 94 unsigned char subtype; /* For future XEM, XR, etc ... */ 95 unsigned short numports; /* Number of ports configured */ 96 unsigned char *port; /* I/O Address */ 97 unsigned char *membase; /* DPR Address */ 98 unsigned char *version; /* For future ... */ 99 unsigned short windowData; /* For future ... */ 100} ; 101