/*
 * Radio tuning for Philips SA2400 on RTL8180
 *
 * Copyright 2007 Andrea Merello <andreamrl@tiscali.it>
 *
 * Code from the BSD driver and the rtl8181 project have been
 * very useful to understand certain things
 *
 * I want to thanks the Authors of such projects and the Ndiswrapper
 * project Authors.
 *
 * A special Big Thanks also is for all people who donated me cards,
 * making possible the creation of the original rtl8180 driver
 * from which this code is derived!
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/init.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <net/mac80211.h>

#include "rtl8180.h"
#include "rtl8180_sa2400.h"

static const u32 sa2400_chan[] = {
        0x00096c, /* ch1 */
        0x080970,
        0x100974,
        0x180978,
        0x000980,
        0x080984,
        0x100988,
        0x18098c,
        0x000994,
        0x080998,
        0x10099c,
        0x1809a0,
        0x0009a8,
        0x0009b4, /* ch 14 */
};

static void write_sa2400(struct ieee80211_hw *dev, u8 addr, u32 data)
{
        struct rtl8180_priv *priv = dev->priv;
        u32 phy_config;

        /* MAC will bang bits to the sa2400. sw 3-wire is NOT used */
        phy_config = 0xb0000000;

        phy_config |= ((u32)(addr & 0xf)) << 24;
        phy_config |= data & 0xffffff;

        rtl818x_iowrite32(priv,
                (__le32 __iomem *) &priv->map->RFPinsOutput, phy_config);

        msleep(3);
}

static void sa2400_write_phy_antenna(struct ieee80211_hw *dev, short chan)
{
        struct rtl8180_priv *priv = dev->priv;
        u8 ant = SA2400_ANTENNA;

        if (priv->rfparam & RF_PARAM_ANTBDEFAULT)
                ant |= BB_ANTENNA_B;

        if (chan == 14)
                ant |= BB_ANTATTEN_CHAN14;

        rtl8180_write_phy(dev, 0x10, ant);

}

static void sa2400_rf_set_channel(struct ieee80211_hw *dev,
                                  struct ieee80211_conf *conf)
{
        struct rtl8180_priv *priv = dev->priv;
        int channel = ieee80211_frequency_to_channel(conf->channel->center_freq);
        u32 txpw = priv->channels[channel - 1].hw_value & 0xFF;
        u32 chan = sa2400_chan[channel - 1];

        write_sa2400(dev, 7, txpw);

        sa2400_write_phy_antenna(dev, channel);

        write_sa2400(dev, 0, chan);
        write_sa2400(dev, 1, 0xbb50);
        write_sa2400(dev, 2, 0x80);
        write_sa2400(dev, 3, 0);
}

static void sa2400_rf_stop(struct ieee80211_hw *dev)
{
        write_sa2400(dev, 4, 0);
}

static void sa2400_rf_init(struct ieee80211_hw *dev)
{
        struct rtl8180_priv *priv = dev->priv;
        u32 anaparam, txconf;
        u8 firdac;
        int analogphy = priv->rfparam & RF_PARAM_ANALOGPHY;

        anaparam = priv->anaparam;
        anaparam &= ~(1 << ANAPARAM_TXDACOFF_SHIFT);
        anaparam &= ~ANAPARAM_PWR1_MASK;
        anaparam &= ~ANAPARAM_PWR0_MASK;

        if (analogphy) {
                anaparam |= SA2400_ANA_ANAPARAM_PWR1_ON << ANAPARAM_PWR1_SHIFT;
                firdac = 0;
        } else {
                anaparam |= (SA2400_DIG_ANAPARAM_PWR1_ON << ANAPARAM_PWR1_SHIFT);
                anaparam |= (SA2400_ANAPARAM_PWR0_ON << ANAPARAM_PWR0_SHIFT);
                firdac = 1 << SA2400_REG4_FIRDAC_SHIFT;
        }

        rtl8180_set_anaparam(priv, anaparam);

        write_sa2400(dev, 0, sa2400_chan[0]);
        write_sa2400(dev, 1, 0xbb50);
        write_sa2400(dev, 2, 0x80);
        write_sa2400(dev, 3, 0);
        write_sa2400(dev, 4, 0x19340 | firdac);
        write_sa2400(dev, 5, 0x1dfb | (SA2400_MAX_SENS - 54) << 15);
        write_sa2400(dev, 4, 0x19348 | firdac); /* calibrate VCO */

        if (!analogphy)
                write_sa2400(dev, 4, 0x1938c); /*???*/

        write_sa2400(dev, 4, 0x19340 | firdac);

        write_sa2400(dev, 0, sa2400_chan[0]);
        write_sa2400(dev, 1, 0xbb50);
        write_sa2400(dev, 2, 0x80);
        write_sa2400(dev, 3, 0);
        write_sa2400(dev, 4, 0x19344 | firdac); /* calibrate filter */

        /* new from rtl8180 embedded driver (rtl8181 project) */
        write_sa2400(dev, 6, 0x13ff | (1 << 23)); /* MANRX */
        write_sa2400(dev, 8, 0); /* VCO */

        if (analogphy) {
                rtl8180_set_anaparam(priv, anaparam |
                                     (1 << ANAPARAM_TXDACOFF_SHIFT));

                txconf = rtl818x_ioread32(priv, &priv->map->TX_CONF);
                rtl818x_iowrite32(priv, &priv->map->TX_CONF,
                        txconf | RTL818X_TX_CONF_LOOPBACK_CONT);

                write_sa2400(dev, 4, 0x19341); /* calibrates DC */

                /* a 5us sleep is required here,
                 * we rely on the 3ms delay introduced in write_sa2400 */
                write_sa2400(dev, 4, 0x19345);

                /* a 20us sleep is required here,
                 * we rely on the 3ms delay introduced in write_sa2400 */

                rtl818x_iowrite32(priv, &priv->map->TX_CONF, txconf);

                rtl8180_set_anaparam(priv, anaparam);
        }
        /* end new code */

        write_sa2400(dev, 4, 0x19341 | firdac); /* RTX MODE */

        /* baseband configuration */
        rtl8180_write_phy(dev, 0, 0x98);
        rtl8180_write_phy(dev, 3, 0x38);
        rtl8180_write_phy(dev, 4, 0xe0);
        rtl8180_write_phy(dev, 5, 0x90);
        rtl8180_write_phy(dev, 6, 0x1a);
        rtl8180_write_phy(dev, 7, 0x64);

        sa2400_write_phy_antenna(dev, 1);

        rtl8180_write_phy(dev, 0x11, 0x80);

        if (rtl818x_ioread8(priv, &priv->map->CONFIG2) &
            RTL818X_CONFIG2_ANTENNA_DIV)
                rtl8180_write_phy(dev, 0x12, 0xc7); /* enable ant diversity */
        else
                rtl8180_write_phy(dev, 0x12, 0x47); /* disable ant diversity */

        rtl8180_write_phy(dev, 0x13, 0x90 | priv->csthreshold);

        rtl8180_write_phy(dev, 0x19, 0x0);
        rtl8180_write_phy(dev, 0x1a, 0xa0);
}

const struct rtl818x_rf_ops sa2400_rf_ops = {
        .name           = "Philips",
        .init           = sa2400_rf_init,
        .stop           = sa2400_rf_stop,
        .set_chan       = sa2400_rf_set_channel
};