/*
 * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
 *
 * Copyright (C) 2004-2007 Texas Instruments
 * Copyright (C) 2008 Nokia Corporation
 * Contact: Felipe Balbi <felipe.balbi@nokia.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 * Current status:
 *      - HS USB ULPI mode works.
 *      - 3-pin mode support may be added in future.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/usb/otg.h>
#include <linux/i2c/twl4030.h>
#include <linux/regulator/consumer.h>
#include <linux/err.h>


/* Register defines */

#define VENDOR_ID_LO                    0x00
#define VENDOR_ID_HI                    0x01
#define PRODUCT_ID_LO                   0x02
#define PRODUCT_ID_HI                   0x03

#define FUNC_CTRL                       0x04
#define FUNC_CTRL_SET                   0x05
#define FUNC_CTRL_CLR                   0x06
#define FUNC_CTRL_SUSPENDM              (1 << 6)
#define FUNC_CTRL_RESET                 (1 << 5)
#define FUNC_CTRL_OPMODE_MASK           (3 << 3) /* bits 3 and 4 */
#define FUNC_CTRL_OPMODE_NORMAL         (0 << 3)
#define FUNC_CTRL_OPMODE_NONDRIVING     (1 << 3)
#define FUNC_CTRL_OPMODE_DISABLE_BIT_NRZI       (2 << 3)
#define FUNC_CTRL_TERMSELECT            (1 << 2)
#define FUNC_CTRL_XCVRSELECT_MASK       (3 << 0) /* bits 0 and 1 */
#define FUNC_CTRL_XCVRSELECT_HS         (0 << 0)
#define FUNC_CTRL_XCVRSELECT_FS         (1 << 0)
#define FUNC_CTRL_XCVRSELECT_LS         (2 << 0)
#define FUNC_CTRL_XCVRSELECT_FS4LS      (3 << 0)

#define IFC_CTRL                        0x07
#define IFC_CTRL_SET                    0x08
#define IFC_CTRL_CLR                    0x09
#define IFC_CTRL_INTERFACE_PROTECT_DISABLE      (1 << 7)
#define IFC_CTRL_AUTORESUME             (1 << 4)
#define IFC_CTRL_CLOCKSUSPENDM          (1 << 3)
#define IFC_CTRL_CARKITMODE             (1 << 2)
#define IFC_CTRL_FSLSSERIALMODE_3PIN    (1 << 1)

#define TWL4030_OTG_CTRL                0x0A
#define TWL4030_OTG_CTRL_SET            0x0B
#define TWL4030_OTG_CTRL_CLR            0x0C
#define TWL4030_OTG_CTRL_DRVVBUS        (1 << 5)
#define TWL4030_OTG_CTRL_CHRGVBUS       (1 << 4)
#define TWL4030_OTG_CTRL_DISCHRGVBUS    (1 << 3)
#define TWL4030_OTG_CTRL_DMPULLDOWN     (1 << 2)
#define TWL4030_OTG_CTRL_DPPULLDOWN     (1 << 1)
#define TWL4030_OTG_CTRL_IDPULLUP       (1 << 0)

#define USB_INT_EN_RISE                 0x0D
#define USB_INT_EN_RISE_SET             0x0E
#define USB_INT_EN_RISE_CLR             0x0F
#define USB_INT_EN_FALL                 0x10
#define USB_INT_EN_FALL_SET             0x11
#define USB_INT_EN_FALL_CLR             0x12
#define USB_INT_STS                     0x13
#define USB_INT_LATCH                   0x14
#define USB_INT_IDGND                   (1 << 4)
#define USB_INT_SESSEND                 (1 << 3)
#define USB_INT_SESSVALID               (1 << 2)
#define USB_INT_VBUSVALID               (1 << 1)
#define USB_INT_HOSTDISCONNECT          (1 << 0)

#define CARKIT_CTRL                     0x19
#define CARKIT_CTRL_SET                 0x1A
#define CARKIT_CTRL_CLR                 0x1B
#define CARKIT_CTRL_MICEN               (1 << 6)
#define CARKIT_CTRL_SPKRIGHTEN          (1 << 5)
#define CARKIT_CTRL_SPKLEFTEN           (1 << 4)
#define CARKIT_CTRL_RXDEN               (1 << 3)
#define CARKIT_CTRL_TXDEN               (1 << 2)
#define CARKIT_CTRL_IDGNDDRV            (1 << 1)
#define CARKIT_CTRL_CARKITPWR           (1 << 0)
#define CARKIT_PLS_CTRL                 0x22
#define CARKIT_PLS_CTRL_SET             0x23
#define CARKIT_PLS_CTRL_CLR             0x24
#define CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN        (1 << 3)
#define CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
#define CARKIT_PLS_CTRL_RXPLSEN         (1 << 1)
#define CARKIT_PLS_CTRL_TXPLSEN         (1 << 0)

#define MCPC_CTRL                       0x30
#define MCPC_CTRL_SET                   0x31
#define MCPC_CTRL_CLR                   0x32
#define MCPC_CTRL_RTSOL                 (1 << 7)
#define MCPC_CTRL_EXTSWR                (1 << 6)
#define MCPC_CTRL_EXTSWC                (1 << 5)
#define MCPC_CTRL_VOICESW               (1 << 4)
#define MCPC_CTRL_OUT64K                (1 << 3)
#define MCPC_CTRL_RTSCTSSW              (1 << 2)
#define MCPC_CTRL_HS_UART               (1 << 0)

#define MCPC_IO_CTRL                    0x33
#define MCPC_IO_CTRL_SET                0x34
#define MCPC_IO_CTRL_CLR                0x35
#define MCPC_IO_CTRL_MICBIASEN          (1 << 5)
#define MCPC_IO_CTRL_CTS_NPU            (1 << 4)
#define MCPC_IO_CTRL_RXD_PU             (1 << 3)
#define MCPC_IO_CTRL_TXDTYP             (1 << 2)
#define MCPC_IO_CTRL_CTSTYP             (1 << 1)
#define MCPC_IO_CTRL_RTSTYP             (1 << 0)

#define MCPC_CTRL2                      0x36
#define MCPC_CTRL2_SET                  0x37
#define MCPC_CTRL2_CLR                  0x38
#define MCPC_CTRL2_MCPC_CK_EN           (1 << 0)

#define OTHER_FUNC_CTRL                 0x80
#define OTHER_FUNC_CTRL_SET             0x81
#define OTHER_FUNC_CTRL_CLR             0x82
#define OTHER_FUNC_CTRL_BDIS_ACON_EN    (1 << 4)
#define OTHER_FUNC_CTRL_FIVEWIRE_MODE   (1 << 2)

#define OTHER_IFC_CTRL                  0x83
#define OTHER_IFC_CTRL_SET              0x84
#define OTHER_IFC_CTRL_CLR              0x85
#define OTHER_IFC_CTRL_OE_INT_EN        (1 << 6)
#define OTHER_IFC_CTRL_CEA2011_MODE     (1 << 5)
#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN      (1 << 4)
#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT       (1 << 3)
#define OTHER_IFC_CTRL_HIZ_ULPI         (1 << 2)
#define OTHER_IFC_CTRL_ALT_INT_REROUTE  (1 << 0)

#define OTHER_INT_EN_RISE               0x86
#define OTHER_INT_EN_RISE_SET           0x87
#define OTHER_INT_EN_RISE_CLR           0x88
#define OTHER_INT_EN_FALL               0x89
#define OTHER_INT_EN_FALL_SET           0x8A
#define OTHER_INT_EN_FALL_CLR           0x8B
#define OTHER_INT_STS                   0x8C
#define OTHER_INT_LATCH                 0x8D
#define OTHER_INT_VB_SESS_VLD           (1 << 7)
#define OTHER_INT_DM_HI                 (1 << 6) /* not valid for "latch" reg */
#define OTHER_INT_DP_HI                 (1 << 5) /* not valid for "latch" reg */
#define OTHER_INT_BDIS_ACON             (1 << 3) /* not valid for "fall" regs */
#define OTHER_INT_MANU                  (1 << 1)
#define OTHER_INT_ABNORMAL_STRESS       (1 << 0)

#define ID_STATUS                       0x96
#define ID_RES_FLOAT                    (1 << 4)
#define ID_RES_440K                     (1 << 3)
#define ID_RES_200K                     (1 << 2)
#define ID_RES_102K                     (1 << 1)
#define ID_RES_GND                      (1 << 0)

#define POWER_CTRL                      0xAC
#define POWER_CTRL_SET                  0xAD
#define POWER_CTRL_CLR                  0xAE
#define POWER_CTRL_OTG_ENAB             (1 << 5)

#define OTHER_IFC_CTRL2                 0xAF
#define OTHER_IFC_CTRL2_SET             0xB0
#define OTHER_IFC_CTRL2_CLR             0xB1
#define OTHER_IFC_CTRL2_ULPI_STP_LOW    (1 << 4)
#define OTHER_IFC_CTRL2_ULPI_TXEN_POL   (1 << 3)
#define OTHER_IFC_CTRL2_ULPI_4PIN_2430  (1 << 2)
#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK     (3 << 0) /* bits 0 and 1 */
#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N    (0 << 0)
#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N    (1 << 0)

#define REG_CTRL_EN                     0xB2
#define REG_CTRL_EN_SET                 0xB3
#define REG_CTRL_EN_CLR                 0xB4
#define REG_CTRL_ERROR                  0xB5
#define ULPI_I2C_CONFLICT_INTEN         (1 << 0)

#define OTHER_FUNC_CTRL2                0xB8
#define OTHER_FUNC_CTRL2_SET            0xB9
#define OTHER_FUNC_CTRL2_CLR            0xBA
#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN  (1 << 0)

/* following registers do not have separate _clr and _set registers */
#define VBUS_DEBOUNCE                   0xC0
#define ID_DEBOUNCE                     0xC1
#define VBAT_TIMER                      0xD3
#define PHY_PWR_CTRL                    0xFD
#define PHY_PWR_PHYPWD                  (1 << 0)
#define PHY_CLK_CTRL                    0xFE
#define PHY_CLK_CTRL_CLOCKGATING_EN     (1 << 2)
#define PHY_CLK_CTRL_CLK32K_EN          (1 << 1)
#define REQ_PHY_DPLL_CLK                (1 << 0)
#define PHY_CLK_CTRL_STS                0xFF
#define PHY_DPLL_CLK                    (1 << 0)

/* In module TWL4030_MODULE_PM_MASTER */
#define PROTECT_KEY                     0x0E
#define STS_HW_CONDITIONS               0x0F

/* In module TWL4030_MODULE_PM_RECEIVER */
#define VUSB_DEDICATED1                 0x7D
#define VUSB_DEDICATED2                 0x7E
#define VUSB1V5_DEV_GRP                 0x71
#define VUSB1V5_TYPE                    0x72
#define VUSB1V5_REMAP                   0x73
#define VUSB1V8_DEV_GRP                 0x74
#define VUSB1V8_TYPE                    0x75
#define VUSB1V8_REMAP                   0x76
#define VUSB3V1_DEV_GRP                 0x77
#define VUSB3V1_TYPE                    0x78
#define VUSB3V1_REMAP                   0x79

/* In module TWL4030_MODULE_INTBR */
#define PMBR1                           0x0D
#define GPIO_USB_4PIN_ULPI_2430C        (3 << 0)



enum linkstat {
        USB_LINK_UNKNOWN = 0,
        USB_LINK_NONE,
        USB_LINK_VBUS,
        USB_LINK_ID,
};

struct twl4030_usb {
        struct otg_transceiver  otg;
        struct device           *dev;

        /* TWL4030 internal USB regulator supplies */
        struct regulator        *usb1v5;
        struct regulator        *usb1v8;
        struct regulator        *usb3v1;

        /* for vbus reporting with irqs disabled */
        spinlock_t              lock;

        /* pin configuration */
        enum twl4030_usb_mode   usb_mode;

        int                     irq;
        u8                      linkstat;
        u8                      asleep;
        bool                    irq_enabled;
};

/* internal define on top of container_of */
#define xceiv_to_twl(x)         container_of((x), struct twl4030_usb, otg);

/*-------------------------------------------------------------------------*/

static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
                u8 module, u8 data, u8 address)
{
        u8 check;

        if ((twl4030_i2c_write_u8(module, data, address) >= 0) &&
            (twl4030_i2c_read_u8(module, &check, address) >= 0) &&
                                                (check == data))
                return 0;
        dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
                        1, module, address, check, data);

        /* Failed once: Try again */
        if ((twl4030_i2c_write_u8(module, data, address) >= 0) &&
            (twl4030_i2c_read_u8(module, &check, address) >= 0) &&
                                                (check == data))
                return 0;
        dev_dbg(twl->dev, "Write%d[%d,0x%x] wrote %02x but read %02x\n",
                        2, module, address, check, data);

        /* Failed again: Return error */
        return -EBUSY;
}

#define twl4030_usb_write_verify(twl, address, data)    \
        twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_USB, (data), (address))

static inline int twl4030_usb_write(struct twl4030_usb *twl,
                u8 address, u8 data)
{
        int ret = 0;

        ret = twl4030_i2c_write_u8(TWL4030_MODULE_USB, data, address);
        if (ret < 0)
                dev_dbg(twl->dev,
                        "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
        return ret;
}

static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
{
        u8 data;
        int ret = 0;

        ret = twl4030_i2c_read_u8(module, &data, address);
        if (ret >= 0)
                ret = data;
        else
                dev_dbg(twl->dev,
                        "TWL4030:readb[0x%x,0x%x] Error %d\n",
                                        module, address, ret);

        return ret;
}

static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
{
        return twl4030_readb(twl, TWL4030_MODULE_USB, address);
}

/*-------------------------------------------------------------------------*/

static inline int
twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
{
        return twl4030_usb_write(twl, reg + 1, bits);
}

static inline int
twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
{
        return twl4030_usb_write(twl, reg + 2, bits);
}

/*-------------------------------------------------------------------------*/

static enum linkstat twl4030_usb_linkstat(struct twl4030_usb *twl)
{
        int     status;
        int     linkstat = USB_LINK_UNKNOWN;

        /*
         * For ID/VBUS sensing, see manual section 15.4.8 ...
         * except when using only battery backup power, two
         * comparators produce VBUS_PRES and ID_PRES signals,
         * which don't match docs elsewhere.  But ... BIT(7)
         * and BIT(2) of STS_HW_CONDITIONS, respectively, do
         * seem to match up.  If either is true the USB_PRES
         * signal is active, the OTG module is activated, and
         * its interrupt may be raised (may wake the system).
         */
        status = twl4030_readb(twl, TWL4030_MODULE_PM_MASTER,
                        STS_HW_CONDITIONS);
        if (status < 0)
                dev_err(twl->dev, "USB link status err %d\n", status);
        else if (status & (BIT(7) | BIT(2))) {
                if (status & BIT(2))
                        linkstat = USB_LINK_ID;
                else
                        linkstat = USB_LINK_VBUS;
        } else
                linkstat = USB_LINK_NONE;

        dev_dbg(twl->dev, "HW_CONDITIONS 0x%02x/%d; link %d\n",
                        status, status, linkstat);

        /* REVISIT this assumes host and peripheral controllers
         * are registered, and that both are active...
         */

        spin_lock_irq(&twl->lock);
        twl->linkstat = linkstat;
        if (linkstat == USB_LINK_ID) {
                twl->otg.default_a = true;
                twl->otg.state = OTG_STATE_A_IDLE;
        } else {
                twl->otg.default_a = false;
                twl->otg.state = OTG_STATE_B_IDLE;
        }
        spin_unlock_irq(&twl->lock);

        return linkstat;
}

static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
{
        twl->usb_mode = mode;

        switch (mode) {
        case T2_USB_MODE_ULPI:
                twl4030_usb_clear_bits(twl, IFC_CTRL, IFC_CTRL_CARKITMODE);
                twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
                twl4030_usb_clear_bits(twl, FUNC_CTRL,
                                        FUNC_CTRL_XCVRSELECT_MASK |
                                        FUNC_CTRL_OPMODE_MASK);
                break;
        case -1:
                /* FIXME: power on defaults */
                break;
        default:
                dev_err(twl->dev, "unsupported T2 transceiver mode %d\n",
                                mode);
                break;
        };
}

static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
{
        unsigned long timeout;
        int val = twl4030_usb_read(twl, PHY_CLK_CTRL);

        if (val >= 0) {
                if (on) {
                        /* enable DPLL to access PHY registers over I2C */
                        val |= REQ_PHY_DPLL_CLK;
                        WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
                                                (u8)val) < 0);

                        timeout = jiffies + HZ;
                        while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
                                                        PHY_DPLL_CLK)
                                && time_before(jiffies, timeout))
                                        udelay(10);
                        if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
                                                        PHY_DPLL_CLK))
                                dev_err(twl->dev, "Timeout setting T2 HSUSB "
                                                "PHY DPLL clock\n");
                } else {
                        /* let ULPI control the DPLL clock */
                        val &= ~REQ_PHY_DPLL_CLK;
                        WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
                                                (u8)val) < 0);
                }
        }
}

static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
        u8 pwr;

        pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
        if (on) {
                regulator_enable(twl->usb3v1);
                regulator_enable(twl->usb1v8);
                /*
                 * Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
                 * in twl4030) resets the VUSB_DEDICATED2 register. This reset
                 * enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
                 * SLEEP. We work around this by clearing the bit after usv3v1
                 * is re-activated. This ensures that VUSB3V1 is really active.
                 */
                twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
                                                        VUSB_DEDICATED2);
                regulator_enable(twl->usb1v5);
                pwr &= ~PHY_PWR_PHYPWD;
                WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
                twl4030_usb_write(twl, PHY_CLK_CTRL,
                                  twl4030_usb_read(twl, PHY_CLK_CTRL) |
                                        (PHY_CLK_CTRL_CLOCKGATING_EN |
                                                PHY_CLK_CTRL_CLK32K_EN));
        } else  {
                pwr |= PHY_PWR_PHYPWD;
                WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
                regulator_disable(twl->usb1v5);
                regulator_disable(twl->usb1v8);
                regulator_disable(twl->usb3v1);
        }
}

static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
{
        if (twl->asleep)
                return;

        twl4030_phy_power(twl, 0);
        twl->asleep = 1;
}

static void twl4030_phy_resume(struct twl4030_usb *twl)
{
        if (!twl->asleep)
                return;

        twl4030_phy_power(twl, 1);
        twl4030_i2c_access(twl, 1);
        twl4030_usb_set_mode(twl, twl->usb_mode);
        if (twl->usb_mode == T2_USB_MODE_ULPI)
                twl4030_i2c_access(twl, 0);
        twl->asleep = 0;
}

static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
{
        /* Enable writing to power configuration registers */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0xC0, PROTECT_KEY);
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0x0C, PROTECT_KEY);

        /* put VUSB3V1 LDO in active state */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);

        /* input to VUSB3V1 LDO is from VBAT, not VBUS */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);

        /* Initialize 3.1V regulator */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);

        twl->usb3v1 = regulator_get(twl->dev, "usb3v1");
        if (IS_ERR(twl->usb3v1))
                return -ENODEV;

        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);

        /* Initialize 1.5V regulator */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);

        twl->usb1v5 = regulator_get(twl->dev, "usb1v5");
        if (IS_ERR(twl->usb1v5))
                goto fail1;

        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);

        /* Initialize 1.8V regulator */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);

        twl->usb1v8 = regulator_get(twl->dev, "usb1v8");
        if (IS_ERR(twl->usb1v8))
                goto fail2;

        twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);

        /* disable access to power configuration registers */
        twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0, PROTECT_KEY);

        return 0;

fail2:
        regulator_put(twl->usb1v5);
        twl->usb1v5 = NULL;
fail1:
        regulator_put(twl->usb3v1);
        twl->usb3v1 = NULL;
        return -ENODEV;
}

static ssize_t twl4030_usb_vbus_show(struct device *dev,
                struct device_attribute *attr, char *buf)
{
        struct twl4030_usb *twl = dev_get_drvdata(dev);
        unsigned long flags;
        int ret = -EINVAL;

        spin_lock_irqsave(&twl->lock, flags);
        ret = sprintf(buf, "%s\n",
                        (twl->linkstat == USB_LINK_VBUS) ? "on" : "off");
        spin_unlock_irqrestore(&twl->lock, flags);

        return ret;
}
static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);

static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
{
        struct twl4030_usb *twl = _twl;
        int status;

#ifdef CONFIG_LOCKDEP
        /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which
         * we don't want and can't tolerate.  Although it might be
         * friendlier not to borrow this thread context...
         */
        local_irq_enable();
#endif

        status = twl4030_usb_linkstat(twl);
        if (status != USB_LINK_UNKNOWN) {

                /* FIXME add a set_power() method so that B-devices can
                 * configure the charger appropriately.  It's not always
                 * correct to consume VBUS power, and how much current to
                 * consume is a function of the USB configuration chosen
                 * by the host.
                 *
                 * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
                 * its disconnect() sibling, when changing to/from the
                 * USB_LINK_VBUS state.  musb_hdrc won't care until it
                 * starts to handle softconnect right.
                 */
                twl4030charger_usb_en(status == USB_LINK_VBUS);

                if (status == USB_LINK_NONE)
                        twl4030_phy_suspend(twl, 0);
                else
                        twl4030_phy_resume(twl);
        }
        sysfs_notify(&twl->dev->kobj, NULL, "vbus");

        return IRQ_HANDLED;
}

static int twl4030_set_suspend(struct otg_transceiver *x, int suspend)
{
        struct twl4030_usb *twl = xceiv_to_twl(x);

        if (suspend)
                twl4030_phy_suspend(twl, 1);
        else
                twl4030_phy_resume(twl);

        return 0;
}

static int twl4030_set_peripheral(struct otg_transceiver *x,
                struct usb_gadget *gadget)
{
        struct twl4030_usb *twl;

        if (!x)
                return -ENODEV;

        twl = xceiv_to_twl(x);
        twl->otg.gadget = gadget;
        if (!gadget)
                twl->otg.state = OTG_STATE_UNDEFINED;

        return 0;
}

static int twl4030_set_host(struct otg_transceiver *x, struct usb_bus *host)
{
        struct twl4030_usb *twl;

        if (!x)
                return -ENODEV;

        twl = xceiv_to_twl(x);
        twl->otg.host = host;
        if (!host)
                twl->otg.state = OTG_STATE_UNDEFINED;

        return 0;
}

static int __devinit twl4030_usb_probe(struct platform_device *pdev)
{
        struct twl4030_usb_data *pdata = pdev->dev.platform_data;
        struct twl4030_usb      *twl;
        int                     status, err;

        if (!pdata) {
                dev_dbg(&pdev->dev, "platform_data not available\n");
                return -EINVAL;
        }

        twl = kzalloc(sizeof *twl, GFP_KERNEL);
        if (!twl)
                return -ENOMEM;

        twl->dev                = &pdev->dev;
        twl->irq                = platform_get_irq(pdev, 0);
        twl->otg.dev            = twl->dev;
        twl->otg.label          = "twl4030";
        twl->otg.set_host       = twl4030_set_host;
        twl->otg.set_peripheral = twl4030_set_peripheral;
        twl->otg.set_suspend    = twl4030_set_suspend;
        twl->usb_mode           = pdata->usb_mode;
        twl->asleep             = 1;

        /* init spinlock for workqueue */
        spin_lock_init(&twl->lock);

        err = twl4030_usb_ldo_init(twl);
        if (err) {
                dev_err(&pdev->dev, "ldo init failed\n");
                kfree(twl);
                return err;
        }
        otg_set_transceiver(&twl->otg);

        platform_set_drvdata(pdev, twl);
        if (device_create_file(&pdev->dev, &dev_attr_vbus))
                dev_warn(&pdev->dev, "could not create sysfs file\n");

        /* Our job is to use irqs and status from the power module
         * to keep the transceiver disabled when nothing's connected.
         *
         * FIXME we actually shouldn't start enabling it until the
         * USB controller drivers have said they're ready, by calling
         * set_host() and/or set_peripheral() ... OTG_capable boards
         * need both handles, otherwise just one suffices.
         */
        twl->irq_enabled = true;
        status = request_irq(twl->irq, twl4030_usb_irq,
                        IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
                        "twl4030_usb", twl);
        if (status < 0) {
                dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
                        twl->irq, status);
                kfree(twl);
                return status;
        }

        /* The IRQ handler just handles changes from the previous states
         * of the ID and VBUS pins ... in probe() we must initialize that
         * previous state.  The easy way:  fake an IRQ.
         *
         * REVISIT:  a real IRQ might have happened already, if PREEMPT is
         * enabled.  Else the IRQ may not yet be configured or enabled,
         * because of scheduling delays.
         */
        twl4030_usb_irq(twl->irq, twl);

        dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
        return 0;
}

static int __exit twl4030_usb_remove(struct platform_device *pdev)
{
        struct twl4030_usb *twl = platform_get_drvdata(pdev);
        int val;

        free_irq(twl->irq, twl);
        device_remove_file(twl->dev, &dev_attr_vbus);

        /* set transceiver mode to power on defaults */
        twl4030_usb_set_mode(twl, -1);

        /* autogate 60MHz ULPI clock,
         * clear dpll clock request for i2c access,
         * disable 32KHz
         */
        val = twl4030_usb_read(twl, PHY_CLK_CTRL);
        if (val >= 0) {
                val |= PHY_CLK_CTRL_CLOCKGATING_EN;
                val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
                twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
        }

        /* disable complete OTG block */
        twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);

        twl4030_phy_power(twl, 0);
        regulator_put(twl->usb1v5);
        regulator_put(twl->usb1v8);
        regulator_put(twl->usb3v1);

        kfree(twl);

        return 0;
}

static struct platform_driver twl4030_usb_driver = {
        .probe          = twl4030_usb_probe,
        .remove         = __exit_p(twl4030_usb_remove),
        .driver         = {
                .name   = "twl4030_usb",
                .owner  = THIS_MODULE,
        },
};

static int __init twl4030_usb_init(void)
{
        return platform_driver_register(&twl4030_usb_driver);
}
subsys_initcall(twl4030_usb_init);

static void __exit twl4030_usb_exit(void)
{
        platform_driver_unregister(&twl4030_usb_driver);
}
module_exit(twl4030_usb_exit);

MODULE_ALIAS("platform:twl4030_usb");
MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
MODULE_LICENSE("GPL");