1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21#include <linux/types.h>
22#include <linux/init.h>
23#include <linux/mm.h>
24#include <linux/module.h>
25#include <linux/platform_device.h>
26#include <linux/spi/spi.h>
27#include <linux/mtd/physmap.h>
28#include <linux/input.h>
29#include <linux/gpio_keys.h>
30
31#include <asm/setup.h>
32#include <asm/mach-types.h>
33#include <asm/irq.h>
34
35#include <asm/mach/arch.h>
36#include <asm/mach/map.h>
37#include <asm/mach/irq.h>
38
39#include <mach/hardware.h>
40#include <mach/board.h>
41#include <mach/gpio.h>
42
43#include "generic.h"
44
45
46static void __init csb337_map_io(void)
47{
48
49 at91rm9200_initialize(3686400, AT91RM9200_BGA);
50
51
52 at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
53
54
55 at91_register_uart(0, 0, 0);
56
57
58 at91_set_serial_console(0);
59}
60
61static void __init csb337_init_irq(void)
62{
63 at91rm9200_init_interrupts(NULL);
64}
65
66static struct at91_eth_data __initdata csb337_eth_data = {
67 .phy_irq_pin = AT91_PIN_PC2,
68 .is_rmii = 0,
69};
70
71static struct at91_usbh_data __initdata csb337_usbh_data = {
72 .ports = 2,
73};
74
75static struct at91_udc_data __initdata csb337_udc_data = {
76
77 .pullup_pin = AT91_PIN_PA24,
78};
79
80static struct i2c_board_info __initdata csb337_i2c_devices[] = {
81 {
82 I2C_BOARD_INFO("ds1307", 0x68),
83 },
84};
85
86static struct at91_cf_data __initdata csb337_cf_data = {
87
88
89
90
91
92
93 .det_pin = AT91_PIN_PC3,
94
95
96 .irq_pin = AT91_PIN_PA19,
97 .vcc_pin = AT91_PIN_PD0,
98 .rst_pin = AT91_PIN_PD2,
99};
100
101static struct at91_mmc_data __initdata csb337_mmc_data = {
102 .det_pin = AT91_PIN_PD5,
103 .slot_b = 0,
104 .wire4 = 1,
105 .wp_pin = AT91_PIN_PD6,
106};
107
108static struct spi_board_info csb337_spi_devices[] = {
109 {
110 .modalias = "sak82c900",
111 .chip_select = 0,
112 .max_speed_hz = 6 * 1000 * 1000,
113 },
114};
115
116#define CSB_FLASH_BASE AT91_CHIPSELECT_0
117#define CSB_FLASH_SIZE SZ_8M
118
119static struct mtd_partition csb_flash_partitions[] = {
120 {
121 .name = "uMON flash",
122 .offset = 0,
123 .size = MTDPART_SIZ_FULL,
124 .mask_flags = MTD_WRITEABLE,
125 }
126};
127
128static struct physmap_flash_data csb_flash_data = {
129 .width = 2,
130 .parts = csb_flash_partitions,
131 .nr_parts = ARRAY_SIZE(csb_flash_partitions),
132};
133
134static struct resource csb_flash_resources[] = {
135 {
136 .start = CSB_FLASH_BASE,
137 .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
138 .flags = IORESOURCE_MEM,
139 }
140};
141
142static struct platform_device csb_flash = {
143 .name = "physmap-flash",
144 .id = 0,
145 .dev = {
146 .platform_data = &csb_flash_data,
147 },
148 .resource = csb_flash_resources,
149 .num_resources = ARRAY_SIZE(csb_flash_resources),
150};
151
152
153
154
155#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
156static struct gpio_keys_button csb300_buttons[] = {
157 {
158 .gpio = AT91_PIN_PB29,
159 .code = BTN_0,
160 .desc = "sw0",
161 .active_low = 1,
162 .wakeup = 1,
163 },
164 {
165 .gpio = AT91_PIN_PB28,
166 .code = BTN_1,
167 .desc = "sw1",
168 .active_low = 1,
169 .wakeup = 1,
170 },
171 {
172 .gpio = AT91_PIN_PA21,
173 .code = BTN_2,
174 .desc = "sw2",
175 .active_low = 1,
176 .wakeup = 1,
177 }
178};
179
180static struct gpio_keys_platform_data csb300_button_data = {
181 .buttons = csb300_buttons,
182 .nbuttons = ARRAY_SIZE(csb300_buttons),
183};
184
185static struct platform_device csb300_button_device = {
186 .name = "gpio-keys",
187 .id = -1,
188 .num_resources = 0,
189 .dev = {
190 .platform_data = &csb300_button_data,
191 }
192};
193
194static void __init csb300_add_device_buttons(void)
195{
196 at91_set_gpio_input(AT91_PIN_PB29, 1);
197 at91_set_deglitch(AT91_PIN_PB29, 1);
198 at91_set_gpio_input(AT91_PIN_PB28, 1);
199 at91_set_deglitch(AT91_PIN_PB28, 1);
200 at91_set_gpio_input(AT91_PIN_PA21, 1);
201 at91_set_deglitch(AT91_PIN_PA21, 1);
202
203 platform_device_register(&csb300_button_device);
204}
205#else
206static void __init csb300_add_device_buttons(void) {}
207#endif
208
209static struct gpio_led csb_leds[] = {
210 {
211 .name = "led0",
212 .gpio = AT91_PIN_PB2,
213 .active_low = 1,
214 .default_trigger = "heartbeat",
215 },
216 {
217 .name = "led1",
218 .gpio = AT91_PIN_PB1,
219 .active_low = 1,
220 .default_trigger = "mmc0",
221 },
222 {
223 .name = "led2",
224 .gpio = AT91_PIN_PB0,
225 .active_low = 1,
226 .default_trigger = "ide-disk",
227 }
228};
229
230
231static void __init csb337_board_init(void)
232{
233
234 at91_add_device_serial();
235
236 at91_add_device_eth(&csb337_eth_data);
237
238 at91_add_device_usbh(&csb337_usbh_data);
239
240 at91_add_device_udc(&csb337_udc_data);
241
242 at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
243
244 at91_set_gpio_input(AT91_PIN_PB22, 1);
245 at91_add_device_cf(&csb337_cf_data);
246
247 at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
248
249 at91_add_device_mmc(0, &csb337_mmc_data);
250
251 platform_device_register(&csb_flash);
252
253 at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
254
255 csb300_add_device_buttons();
256}
257
258MACHINE_START(CSB337, "Cogent CSB337")
259
260 .boot_params = AT91_SDRAM_BASE + 0x100,
261 .timer = &at91rm9200_timer,
262 .map_io = csb337_map_io,
263 .init_irq = csb337_init_irq,
264 .init_machine = csb337_board_init,
265MACHINE_END
266
