linux/arch/arm/mach-orion5x/ts409-setup.c
<<
>>
Prefs
   1/*
   2 * QNAP TS-409 Board Setup
   3 *
   4 * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com>
   5 *
   6 * Copyright (C) 2008  Sylver Bruneau <sylver.bruneau@gmail.com>
   7 * Copyright (C) 2008  Martin Michlmayr <tbm@cyrius.com>
   8 *
   9 * This program is free software; you can redistribute it and/or
  10 * modify it under the terms of the GNU General Public License
  11 * as published by the Free Software Foundation; either version
  12 * 2 of the License, or (at your option) any later version.
  13 */
  14
  15#include <linux/kernel.h>
  16#include <linux/init.h>
  17#include <linux/platform_device.h>
  18#include <linux/pci.h>
  19#include <linux/irq.h>
  20#include <linux/mtd/physmap.h>
  21#include <linux/mv643xx_eth.h>
  22#include <linux/leds.h>
  23#include <linux/gpio_keys.h>
  24#include <linux/input.h>
  25#include <linux/i2c.h>
  26#include <linux/serial_reg.h>
  27#include <asm/mach-types.h>
  28#include <asm/gpio.h>
  29#include <asm/mach/arch.h>
  30#include <asm/mach/pci.h>
  31#include <mach/orion5x.h>
  32#include "common.h"
  33#include "mpp.h"
  34#include "tsx09-common.h"
  35
  36/*****************************************************************************
  37 * QNAP TS-409 Info
  38 ****************************************************************************/
  39
  40/*
  41 * QNAP TS-409 hardware :
  42 * - Marvell 88F5281-D0
  43 * - Marvell 88SX7042 SATA controller (PCIe)
  44 * - Marvell 88E1118 Gigabit Ethernet PHY
  45 * - RTC S35390A (@0x30) on I2C bus
  46 * - 8MB NOR flash
  47 * - 256MB of DDR-2 RAM
  48 */
  49
  50/*
  51 * 8MB NOR flash Device bus boot chip select
  52 */
  53
  54#define QNAP_TS409_NOR_BOOT_BASE 0xff800000
  55#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M
  56
  57/****************************************************************************
  58 * 8MiB NOR flash. The struct mtd_partition is not in the same order as the
  59 *     partitions on the device because we want to keep compatability with
  60 *     existing QNAP firmware.
  61 *
  62 * Layout as used by QNAP:
  63 *  [2] 0x00000000-0x00200000 : "Kernel"
  64 *  [3] 0x00200000-0x00600000 : "RootFS1"
  65 *  [4] 0x00600000-0x00700000 : "RootFS2"
  66 *  [6] 0x00700000-0x00760000 : "NAS Config" (read-only)
  67 *  [5] 0x00760000-0x00780000 : "U-Boot Config"
  68 *  [1] 0x00780000-0x00800000 : "U-Boot" (read-only)
  69 ***************************************************************************/
  70static struct mtd_partition qnap_ts409_partitions[] = {
  71        {
  72                .name           = "U-Boot",
  73                .size           = 0x00080000,
  74                .offset         = 0x00780000,
  75                .mask_flags     = MTD_WRITEABLE,
  76        }, {
  77                .name           = "Kernel",
  78                .size           = 0x00200000,
  79                .offset         = 0,
  80        }, {
  81                .name           = "RootFS1",
  82                .size           = 0x00400000,
  83                .offset         = 0x00200000,
  84        }, {
  85                .name           = "RootFS2",
  86                .size           = 0x00100000,
  87                .offset         = 0x00600000,
  88        }, {
  89                .name           = "U-Boot Config",
  90                .size           = 0x00020000,
  91                .offset         = 0x00760000,
  92        }, {
  93                .name           = "NAS Config",
  94                .size           = 0x00060000,
  95                .offset         = 0x00700000,
  96                .mask_flags     = MTD_WRITEABLE,
  97        },
  98};
  99
 100static struct physmap_flash_data qnap_ts409_nor_flash_data = {
 101        .width          = 1,
 102        .parts          = qnap_ts409_partitions,
 103        .nr_parts       = ARRAY_SIZE(qnap_ts409_partitions)
 104};
 105
 106static struct resource qnap_ts409_nor_flash_resource = {
 107        .flags  = IORESOURCE_MEM,
 108        .start  = QNAP_TS409_NOR_BOOT_BASE,
 109        .end    = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1,
 110};
 111
 112static struct platform_device qnap_ts409_nor_flash = {
 113        .name           = "physmap-flash",
 114        .id             = 0,
 115        .dev            = { .platform_data = &qnap_ts409_nor_flash_data, },
 116        .num_resources  = 1,
 117        .resource       = &qnap_ts409_nor_flash_resource,
 118};
 119
 120/*****************************************************************************
 121 * PCI
 122 ****************************************************************************/
 123
 124static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
 125{
 126        int irq;
 127
 128        /*
 129         * Check for devices with hard-wired IRQs.
 130         */
 131        irq = orion5x_pci_map_irq(dev, slot, pin);
 132        if (irq != -1)
 133                return irq;
 134
 135        /*
 136         * PCI isn't used on the TS-409
 137         */
 138        return -1;
 139}
 140
 141static struct hw_pci qnap_ts409_pci __initdata = {
 142        .nr_controllers = 2,
 143        .swizzle        = pci_std_swizzle,
 144        .setup          = orion5x_pci_sys_setup,
 145        .scan           = orion5x_pci_sys_scan_bus,
 146        .map_irq        = qnap_ts409_pci_map_irq,
 147};
 148
 149static int __init qnap_ts409_pci_init(void)
 150{
 151        if (machine_is_ts409())
 152                pci_common_init(&qnap_ts409_pci);
 153
 154        return 0;
 155}
 156
 157subsys_initcall(qnap_ts409_pci_init);
 158
 159/*****************************************************************************
 160 * RTC S35390A on I2C bus
 161 ****************************************************************************/
 162
 163#define TS409_RTC_GPIO  10
 164
 165static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = {
 166        I2C_BOARD_INFO("s35390a", 0x30),
 167};
 168
 169/*****************************************************************************
 170 * LEDs attached to GPIO
 171 ****************************************************************************/
 172
 173static struct gpio_led ts409_led_pins[] = {
 174        {
 175                .name           = "ts409:red:sata1",
 176                .gpio           = 4,
 177                .active_low     = 1,
 178        }, {
 179                .name           = "ts409:red:sata2",
 180                .gpio           = 5,
 181                .active_low     = 1,
 182        }, {
 183                .name           = "ts409:red:sata3",
 184                .gpio           = 6,
 185                .active_low     = 1,
 186        }, {
 187                .name           = "ts409:red:sata4",
 188                .gpio           = 7,
 189                .active_low     = 1,
 190        },
 191};
 192
 193static struct gpio_led_platform_data ts409_led_data = {
 194        .leds           = ts409_led_pins,
 195        .num_leds       = ARRAY_SIZE(ts409_led_pins),
 196};
 197
 198static struct platform_device ts409_leds = {
 199        .name   = "leds-gpio",
 200        .id     = -1,
 201        .dev    = {
 202                .platform_data  = &ts409_led_data,
 203        },
 204};
 205
 206/****************************************************************************
 207 * GPIO Attached Keys
 208 *     Power button is attached to the PIC microcontroller
 209 ****************************************************************************/
 210
 211#define QNAP_TS409_GPIO_KEY_RESET       14
 212#define QNAP_TS409_GPIO_KEY_MEDIA       15
 213
 214static struct gpio_keys_button qnap_ts409_buttons[] = {
 215        {
 216                .code           = KEY_RESTART,
 217                .gpio           = QNAP_TS409_GPIO_KEY_RESET,
 218                .desc           = "Reset Button",
 219                .active_low     = 1,
 220        }, {
 221                .code           = KEY_COPY,
 222                .gpio           = QNAP_TS409_GPIO_KEY_MEDIA,
 223                .desc           = "USB Copy Button",
 224                .active_low     = 1,
 225        },
 226};
 227
 228static struct gpio_keys_platform_data qnap_ts409_button_data = {
 229        .buttons        = qnap_ts409_buttons,
 230        .nbuttons       = ARRAY_SIZE(qnap_ts409_buttons),
 231};
 232
 233static struct platform_device qnap_ts409_button_device = {
 234        .name           = "gpio-keys",
 235        .id             = -1,
 236        .num_resources  = 0,
 237        .dev            = {
 238                .platform_data  = &qnap_ts409_button_data,
 239        },
 240};
 241
 242/*****************************************************************************
 243 * General Setup
 244 ****************************************************************************/
 245static struct orion5x_mpp_mode ts409_mpp_modes[] __initdata = {
 246        {  0, MPP_UNUSED },
 247        {  1, MPP_UNUSED },
 248        {  2, MPP_UNUSED },
 249        {  3, MPP_UNUSED },
 250        {  4, MPP_GPIO },               /* HDD 1 status */
 251        {  5, MPP_GPIO },               /* HDD 2 status */
 252        {  6, MPP_GPIO },               /* HDD 3 status */
 253        {  7, MPP_GPIO },               /* HDD 4 status */
 254        {  8, MPP_UNUSED },
 255        {  9, MPP_UNUSED },
 256        { 10, MPP_GPIO },               /* RTC int */
 257        { 11, MPP_UNUSED },
 258        { 12, MPP_UNUSED },
 259        { 13, MPP_UNUSED },
 260        { 14, MPP_GPIO },               /* SW_RST */
 261        { 15, MPP_GPIO },               /* USB copy button */
 262        { 16, MPP_UART },               /* UART1 RXD */
 263        { 17, MPP_UART },               /* UART1 TXD */
 264        { 18, MPP_UNUSED },
 265        { 19, MPP_UNUSED },
 266        { -1 },
 267};
 268
 269static void __init qnap_ts409_init(void)
 270{
 271        /*
 272         * Setup basic Orion functions. Need to be called early.
 273         */
 274        orion5x_init();
 275
 276        orion5x_mpp_conf(ts409_mpp_modes);
 277
 278        /*
 279         * Configure peripherals.
 280         */
 281        orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE,
 282                                   QNAP_TS409_NOR_BOOT_SIZE);
 283        platform_device_register(&qnap_ts409_nor_flash);
 284
 285        orion5x_ehci0_init();
 286        qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE +
 287                                 qnap_ts409_partitions[5].offset,
 288                                 qnap_ts409_partitions[5].size);
 289        orion5x_eth_init(&qnap_tsx09_eth_data);
 290        orion5x_i2c_init();
 291        orion5x_uart0_init();
 292        orion5x_uart1_init();
 293
 294        platform_device_register(&qnap_ts409_button_device);
 295
 296        /* Get RTC IRQ and register the chip */
 297        if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) {
 298                if (gpio_direction_input(TS409_RTC_GPIO) == 0)
 299                        qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO);
 300                else
 301                        gpio_free(TS409_RTC_GPIO);
 302        }
 303        if (qnap_ts409_i2c_rtc.irq == 0)
 304                pr_warning("qnap_ts409_init: failed to get RTC IRQ\n");
 305        i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1);
 306        platform_device_register(&ts409_leds);
 307
 308        /* register tsx09 specific power-off method */
 309        pm_power_off = qnap_tsx09_power_off;
 310}
 311
 312MACHINE_START(TS409, "QNAP TS-409")
 313        /* Maintainer:  Sylver Bruneau <sylver.bruneau@gmail.com> */
 314        .boot_params    = 0x00000100,
 315        .init_machine   = qnap_ts409_init,
 316        .map_io         = orion5x_map_io,
 317        .init_irq       = orion5x_init_irq,
 318        .timer          = &orion5x_timer,
 319        .fixup          = tag_fixup_mem32,
 320MACHINE_END
 321