/*  linux/arch/arm/mach-pxa/xcep.c
 *
 *  Support for the Iskratel Electronics XCEP platform as used in
 *  the Libera instruments from Instrumentation Technologies.
 *
 *  Author:     Ales Bardorfer <ales@i-tech.si>
 *  Contributions by: Abbott, MG (Michael) <michael.abbott@diamond.ac.uk>
 *  Contributions by: Matej Kenda <matej.kenda@i-tech.si>
 *  Created:    June 2006
 *  Copyright:  (C) 2006-2009 Instrumentation Technologies
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License version 2 as
 *  published by the Free Software Foundation.
 */

#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/smc91x.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>

#include <plat/i2c.h>

#include <mach/hardware.h>
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa25x.h>
#include <mach/smemc.h>

#include "generic.h"

#define XCEP_ETH_PHYS           (PXA_CS3_PHYS + 0x00000300)
#define XCEP_ETH_PHYS_END       (PXA_CS3_PHYS + 0x000fffff)
#define XCEP_ETH_ATTR           (PXA_CS3_PHYS + 0x02000000)
#define XCEP_ETH_ATTR_END       (PXA_CS3_PHYS + 0x020fffff)
#define XCEP_ETH_IRQ            IRQ_GPIO0

/*  XCEP CPLD base */
#define XCEP_CPLD_BASE          0xf0000000


/* Flash partitions. */

static struct mtd_partition xcep_partitions[] = {
        {
                .name =         "Bootloader",
                .size =         0x00040000,
                .offset =       0,
                .mask_flags =   MTD_WRITEABLE
        }, {
                .name =         "Bootloader ENV",
                .size =         0x00040000,
                .offset =       0x00040000,
                .mask_flags =   MTD_WRITEABLE
        }, {
                .name =         "Kernel",
                .size =         0x00100000,
                .offset =       0x00080000,
        }, {
                .name =         "Rescue fs",
                .size =         0x00280000,
                .offset =       0x00180000,
        }, {
                .name =         "Filesystem",
                .size =         MTDPART_SIZ_FULL,
                .offset =       0x00400000
        }
};

static struct physmap_flash_data xcep_flash_data[] = {
        {
                .width          = 4,            /* bankwidth in bytes */
                .parts          = xcep_partitions,
                .nr_parts       = ARRAY_SIZE(xcep_partitions)
        }
};

static struct resource flash_resource = {
        .start  = PXA_CS0_PHYS,
        .end    = PXA_CS0_PHYS + SZ_32M - 1,
        .flags  = IORESOURCE_MEM,
};

static struct platform_device flash_device = {
        .name   = "physmap-flash",
        .id     = 0,
        .dev    = {
                .platform_data = xcep_flash_data,
        },
        .resource = &flash_resource,
        .num_resources = 1,
};



/* SMC LAN91C111 network controller. */

static struct resource smc91x_resources[] = {
        [0] = {
                .name   = "smc91x-regs",
                .start  = XCEP_ETH_PHYS,
                .end    = XCEP_ETH_PHYS_END,
                .flags  = IORESOURCE_MEM,
        },
        [1] = {
                .start  = XCEP_ETH_IRQ,
                .end    = XCEP_ETH_IRQ,
                .flags  = IORESOURCE_IRQ,
        },
        [2] = {
                .name   = "smc91x-attrib",
                .start  = XCEP_ETH_ATTR,
                .end    = XCEP_ETH_ATTR_END,
                .flags  = IORESOURCE_MEM,
        },
};

static struct smc91x_platdata xcep_smc91x_info = {
        .flags  = SMC91X_USE_32BIT | SMC91X_NOWAIT | SMC91X_USE_DMA,
};

static struct platform_device smc91x_device = {
        .name           = "smc91x",
        .id             = -1,
        .num_resources  = ARRAY_SIZE(smc91x_resources),
        .resource       = smc91x_resources,
        .dev            = {
                .platform_data = &xcep_smc91x_info,
        },
};


static struct platform_device *devices[] __initdata = {
        &flash_device,
        &smc91x_device,
};


/* We have to state that there are HWMON devices on the I2C bus on XCEP.
 * Drivers for HWMON verify capabilities of the adapter when loading and
 * refuse to attach if the adapter doesn't support HWMON class of devices.
 * See also Documentation/i2c/porting-clients. */
static struct i2c_pxa_platform_data xcep_i2c_platform_data  = {
        .class = I2C_CLASS_HWMON
};


static mfp_cfg_t xcep_pin_config[] __initdata = {
        GPIO79_nCS_3,   /* SMC 91C111 chip select. */
        GPIO80_nCS_4,   /* CPLD chip select. */
        /* SSP communication to MSP430 */
        GPIO23_SSP1_SCLK,
        GPIO24_SSP1_SFRM,
        GPIO25_SSP1_TXD,
        GPIO26_SSP1_RXD,
        GPIO27_SSP1_EXTCLK
};

static void __init xcep_init(void)
{
        pxa2xx_mfp_config(ARRAY_AND_SIZE(xcep_pin_config));

        pxa_set_ffuart_info(NULL);
        pxa_set_btuart_info(NULL);
        pxa_set_stuart_info(NULL);
        pxa_set_hwuart_info(NULL);

        /* See Intel XScale Developer's Guide for details */
        /* Set RDF and RDN to appropriate values (chip select 3 (smc91x)) */
        __raw_writel((__raw_readl(MSC1) & 0xffff) | 0xD5540000, MSC1);
        /* Set RDF and RDN to appropriate values (chip select 5 (fpga)) */
        __raw_writel((__raw_readl(MSC2) & 0xffff) | 0x72A00000, MSC2);

        platform_add_devices(ARRAY_AND_SIZE(devices));
        pxa_set_i2c_info(&xcep_i2c_platform_data);
}

MACHINE_START(XCEP, "Iskratel XCEP")
        .boot_params    = 0xa0000100,
        .init_machine   = xcep_init,
        .map_io         = pxa25x_map_io,
        .init_irq       = pxa25x_init_irq,
        .timer          = &pxa_timer,
MACHINE_END