LXR linux/arch/x86/pci/olpc.c

   1/*
   2 * Low-level PCI config space access for OLPC systems who lack the VSA
   3 * PCI virtualization software.
   4 *
   5 * Copyright © 2006  Advanced Micro Devices, Inc.
   6 *
   7 * This program is free software; you can redistribute it and/or modify
   8 * it under the terms of the GNU General Public License as published by
   9 * the Free Software Foundation; either version 2 of the License, or
  10 * (at your option) any later version.
  11 *
  12 * The AMD Geode chipset (ie: GX2 processor, cs5536 I/O companion device)
  13 * has some I/O functions (display, southbridge, sound, USB HCIs, etc)
  14 * that more or less behave like PCI devices, but the hardware doesn't
  15 * directly implement the PCI configuration space headers.  AMD provides
  16 * "VSA" (Virtual System Architecture) software that emulates PCI config
  17 * space for these devices, by trapping I/O accesses to PCI config register
  18 * (CF8/CFC) and running some code in System Management Mode interrupt state.
  19 * On the OLPC platform, we don't want to use that VSA code because
  20 * (a) it slows down suspend/resume, and (b) recompiling it requires special
  21 * compilers that are hard to get.  So instead of letting the complex VSA
  22 * code simulate the PCI config registers for the on-chip devices, we
  23 * just simulate them the easy way, by inserting the code into the
  24 * pci_write_config and pci_read_config path.  Most of the config registers
  25 * are read-only anyway, so the bulk of the simulation is just table lookup.
  26 */
  27
  28#include <linux/pci.h>
  29#include <linux/init.h>
  30#include <asm/olpc.h>
  31#include <asm/geode.h>
  32#include <asm/pci_x86.h>
  33
  34/*
  35 * In the tables below, the first two line (8 longwords) are the
  36 * size masks that are used when the higher level PCI code determines
  37 * the size of the region by writing ~0 to a base address register
  38 * and reading back the result.
  39 *
  40 * The following lines are the values that are read during normal
  41 * PCI config access cycles, i.e. not after just having written
  42 * ~0 to a base address register.
  43 */
  44
  45static const uint32_t lxnb_hdr[] = {  /* dev 1 function 0 - devfn = 8 */
  46        0x0,    0x0,    0x0,    0x0,
  47        0x0,    0x0,    0x0,    0x0,
  48
  49        0x281022, 0x2200005, 0x6000021, 0x80f808,       /* AMD Vendor ID */
  50        0x0,    0x0,    0x0,    0x0,   /* No virtual registers, hence no BAR */
  51        0x0,    0x0,    0x0,    0x28100b,
  52        0x0,    0x0,    0x0,    0x0,
  53        0x0,    0x0,    0x0,    0x0,
  54        0x0,    0x0,    0x0,    0x0,
  55        0x0,    0x0,    0x0,    0x0,
  56};
  57
  58static const uint32_t gxnb_hdr[] = {  /* dev 1 function 0 - devfn = 8 */
  59        0xfffffffd, 0x0, 0x0,   0x0,
  60        0x0,    0x0,    0x0,    0x0,
  61
  62        0x28100b, 0x2200005, 0x6000021, 0x80f808,       /* NSC Vendor ID */
  63        0xac1d, 0x0,    0x0,    0x0,  /* I/O BAR - base of virtual registers */
  64        0x0,    0x0,    0x0,    0x28100b,
  65        0x0,    0x0,    0x0,    0x0,
  66        0x0,    0x0,    0x0,    0x0,
  67        0x0,    0x0,    0x0,    0x0,
  68        0x0,    0x0,    0x0,    0x0,
  69};
  70
  71static const uint32_t lxfb_hdr[] = {  /* dev 1 function 1 - devfn = 9 */
  72        0xff000008, 0xffffc000, 0xffffc000, 0xffffc000,
  73        0xffffc000,     0x0,    0x0,    0x0,
  74
  75        0x20811022, 0x2200003, 0x3000000, 0x0,          /* AMD Vendor ID */
  76        0xfd000000, 0xfe000000, 0xfe004000, 0xfe008000, /* FB, GP, VG, DF */
  77        0xfe00c000, 0x0, 0x0,   0x30100b,               /* VIP */
  78        0x0,    0x0,    0x0,    0x10e,     /* INTA, IRQ14 for graphics accel */
  79        0x0,    0x0,    0x0,    0x0,
  80        0x3d0,  0x3c0,  0xa0000, 0x0,       /* VG IO, VG IO, EGA FB, MONO FB */
  81        0x0,    0x0,    0x0,    0x0,
  82};
  83
  84static const uint32_t gxfb_hdr[] = {  /* dev 1 function 1 - devfn = 9 */
  85        0xff800008, 0xffffc000, 0xffffc000, 0xffffc000,
  86        0x0,    0x0,    0x0,    0x0,
  87
  88        0x30100b, 0x2200003, 0x3000000, 0x0,            /* NSC Vendor ID */
  89        0xfd000000, 0xfe000000, 0xfe004000, 0xfe008000, /* FB, GP, VG, DF */
  90        0x0,    0x0,    0x0,    0x30100b,
  91        0x0,    0x0,    0x0,    0x0,
  92        0x0,    0x0,    0x0,    0x0,
  93        0x3d0,  0x3c0,  0xa0000, 0x0,       /* VG IO, VG IO, EGA FB, MONO FB */
  94        0x0,    0x0,    0x0,    0x0,
  95};
  96
  97static const uint32_t aes_hdr[] = {     /* dev 1 function 2 - devfn = 0xa */
  98        0xffffc000, 0x0, 0x0,   0x0,
  99        0x0,    0x0,    0x0,    0x0,
 100
 101        0x20821022, 0x2a00006, 0x10100000, 0x8,         /* NSC Vendor ID */
 102        0xfe010000, 0x0, 0x0,   0x0,                    /* AES registers */
 103        0x0,    0x0,    0x0,    0x20821022,
 104        0x0,    0x0,    0x0,    0x0,
 105        0x0,    0x0,    0x0,    0x0,
 106        0x0,    0x0,    0x0,    0x0,
 107        0x0,    0x0,    0x0,    0x0,
 108};
 109
 110
 111static const uint32_t isa_hdr[] = {  /* dev f function 0 - devfn = 78 */
 112        0xfffffff9, 0xffffff01, 0xffffffc1, 0xffffffe1,
 113        0xffffff81, 0xffffffc1, 0x0, 0x0,
 114
 115        0x20901022, 0x2a00049, 0x6010003, 0x802000,
 116        0x18b1, 0x1001, 0x1801, 0x1881, /* SMB-8   GPIO-256 MFGPT-64  IRQ-32 */
 117        0x1401, 0x1841, 0x0,    0x20901022,             /* PMS-128 ACPI-64 */
 118        0x0,    0x0,    0x0,    0x0,
 119        0x0,    0x0,    0x0,    0x0,
 120        0x0,    0x0,    0x0,    0xaa5b,                 /* IRQ steering */
 121        0x0,    0x0,    0x0,    0x0,
 122};
 123
 124static const uint32_t ac97_hdr[] = {  /* dev f function 3 - devfn = 7b */
 125        0xffffff81, 0x0, 0x0,   0x0,
 126        0x0,    0x0,    0x0,    0x0,
 127
 128        0x20931022, 0x2a00041, 0x4010001, 0x0,
 129        0x1481, 0x0,    0x0,    0x0,                    /* I/O BAR-128 */
 130        0x0,    0x0,    0x0,    0x20931022,
 131        0x0,    0x0,    0x0,    0x205,                  /* IntB, IRQ5 */
 132        0x0,    0x0,    0x0,    0x0,
 133        0x0,    0x0,    0x0,    0x0,
 134        0x0,    0x0,    0x0,    0x0,
 135};
 136
 137static const uint32_t ohci_hdr[] = {  /* dev f function 4 - devfn = 7c */
 138        0xfffff000, 0x0, 0x0,   0x0,
 139        0x0,    0x0,    0x0,    0x0,
 140
 141        0x20941022, 0x2300006, 0xc031002, 0x0,
 142        0xfe01a000, 0x0, 0x0,   0x0,                    /* MEMBAR-1000 */
 143        0x0,    0x0,    0x0,    0x20941022,
 144        0x0,    0x40,   0x0,    0x40a,                  /* CapPtr INT-D, IRQA */
 145        0xc8020001, 0x0, 0x0,   0x0,    /* Capabilities - 40 is R/O,
 146                                           44 is mask 8103 (power control) */
 147        0x0,    0x0,    0x0,    0x0,
 148        0x0,    0x0,    0x0,    0x0,
 149};
 150
 151static const uint32_t ehci_hdr[] = {  /* dev f function 4 - devfn = 7d */
 152        0xfffff000, 0x0, 0x0,   0x0,
 153        0x0,    0x0,    0x0,    0x0,
 154
 155        0x20951022, 0x2300006, 0xc032002, 0x0,
 156        0xfe01b000, 0x0, 0x0,   0x0,                    /* MEMBAR-1000 */
 157        0x0,    0x0,    0x0,    0x20951022,
 158        0x0,    0x40,   0x0,    0x40a,                  /* CapPtr INT-D, IRQA */
 159        0xc8020001, 0x0, 0x0,   0x0,    /* Capabilities - 40 is R/O, 44 is
 160                                           mask 8103 (power control) */
 161#if 0
 162        0x1,    0x40080000, 0x0, 0x0,   /* EECP - see EHCI spec section 2.1.7 */
 163#endif
 164        0x01000001, 0x0, 0x0,   0x0,    /* EECP - see EHCI spec section 2.1.7 */
 165        0x2020, 0x0,    0x0,    0x0,    /* (EHCI page 8) 60 SBRN (R/O),
 166                                           61 FLADJ (R/W), PORTWAKECAP  */
 167};
 168
 169static uint32_t ff_loc = ~0;
 170static uint32_t zero_loc;
 171static int bar_probing;         /* Set after a write of ~0 to a BAR */
 172static int is_lx;
 173
 174#define NB_SLOT 0x1     /* Northbridge - GX chip - Device 1 */
 175#define SB_SLOT 0xf     /* Southbridge - CS5536 chip - Device F */
 176
 177static int is_simulated(unsigned int bus, unsigned int devfn)
 178{
 179        return (!bus && ((PCI_SLOT(devfn) == NB_SLOT) ||
 180                        (PCI_SLOT(devfn) == SB_SLOT)));
 181}
 182
 183static uint32_t *hdr_addr(const uint32_t *hdr, int reg)
 184{
 185        uint32_t addr;
 186
 187        /*
 188         * This is a little bit tricky.  The header maps consist of
 189         * 0x20 bytes of size masks, followed by 0x70 bytes of header data.
 190         * In the normal case, when not probing a BAR's size, we want
 191         * to access the header data, so we add 0x20 to the reg offset,
 192         * thus skipping the size mask area.
 193         * In the BAR probing case, we want to access the size mask for
 194         * the BAR, so we subtract 0x10 (the config header offset for
 195         * BAR0), and don't skip the size mask area.
 196         */
 197
 198        addr = (uint32_t)hdr + reg + (bar_probing ? -0x10 : 0x20);
 199
 200        bar_probing = 0;
 201        return (uint32_t *)addr;
 202}
 203
 204static int pci_olpc_read(unsigned int seg, unsigned int bus,
 205                unsigned int devfn, int reg, int len, uint32_t *value)
 206{
 207        uint32_t *addr;
 208
 209        /* Use the hardware mechanism for non-simulated devices */
 210        if (!is_simulated(bus, devfn))
 211                return pci_direct_conf1.read(seg, bus, devfn, reg, len, value);
 212
 213        /*
 214         * No device has config registers past 0x70, so we save table space
 215         * by not storing entries for the nonexistent registers
 216         */
 217        if (reg >= 0x70)
 218                addr = &zero_loc;
 219        else {
 220                switch (devfn) {
 221                case  0x8:
 222                        addr = hdr_addr(is_lx ? lxnb_hdr : gxnb_hdr, reg);
 223                        break;
 224                case  0x9:
 225                        addr = hdr_addr(is_lx ? lxfb_hdr : gxfb_hdr, reg);
 226                        break;
 227                case  0xa:
 228                        addr = is_lx ? hdr_addr(aes_hdr, reg) : &ff_loc;
 229                        break;
 230                case 0x78:
 231                        addr = hdr_addr(isa_hdr, reg);
 232                        break;
 233                case 0x7b:
 234                        addr = hdr_addr(ac97_hdr, reg);
 235                        break;
 236                case 0x7c:
 237                        addr = hdr_addr(ohci_hdr, reg);
 238                        break;
 239                case 0x7d:
 240                        addr = hdr_addr(ehci_hdr, reg);
 241                        break;
 242                default:
 243                        addr = &ff_loc;
 244                        break;
 245                }
 246        }
 247        switch (len) {
 248        case 1:
 249                *value = *(uint8_t *)addr;
 250                break;
 251        case 2:
 252                *value = *(uint16_t *)addr;
 253                break;
 254        case 4:
 255                *value = *addr;
 256                break;
 257        default:
 258                BUG();
 259        }
 260
 261        return 0;
 262}
 263
 264static int pci_olpc_write(unsigned int seg, unsigned int bus,
 265                unsigned int devfn, int reg, int len, uint32_t value)
 266{
 267        /* Use the hardware mechanism for non-simulated devices */
 268        if (!is_simulated(bus, devfn))
 269                return pci_direct_conf1.write(seg, bus, devfn, reg, len, value);
 270
 271        /* XXX we may want to extend this to simulate EHCI power management */
 272
 273        /*
 274         * Mostly we just discard writes, but if the write is a size probe
 275         * (i.e. writing ~0 to a BAR), we remember it and arrange to return
 276         * the appropriate size mask on the next read.  This is cheating
 277         * to some extent, because it depends on the fact that the next
 278         * access after such a write will always be a read to the same BAR.
 279         */
 280
 281        if ((reg >= 0x10) && (reg < 0x2c)) {
 282                /* write is to a BAR */
 283                if (value == ~0)
 284                        bar_probing = 1;
 285        } else {
 286                /*
 287                 * No warning on writes to ROM BAR, CMD, LATENCY_TIMER,
 288                 * CACHE_LINE_SIZE, or PM registers.
 289                 */
 290                if ((reg != PCI_ROM_ADDRESS) && (reg != PCI_COMMAND_MASTER) &&
 291                                (reg != PCI_LATENCY_TIMER) &&
 292                                (reg != PCI_CACHE_LINE_SIZE) && (reg != 0x44))
 293                        printk(KERN_WARNING "OLPC PCI: Config write to devfn"
 294                                " %x reg %x value %x\n", devfn, reg, value);
 295        }
 296
 297        return 0;
 298}
 299
 300static struct pci_raw_ops pci_olpc_conf = {
 301        .read = pci_olpc_read,
 302        .write = pci_olpc_write,
 303};
 304
 305int __init pci_olpc_init(void)
 306{
 307        printk(KERN_INFO "PCI: Using configuration type OLPC XO-1\n");
 308        raw_pci_ops = &pci_olpc_conf;
 309        is_lx = is_geode_lx();
 310        return 0;
 311}
 312