1
2
3
4
5
6
7
8comment "Parallel IDE high-level drivers"
9 depends on PARIDE
10
11config PARIDE_PD
12 tristate "Parallel port IDE disks"
13 depends on PARIDE
14 help
15 This option enables the high-level driver for IDE-type disk devices
16 connected through a parallel port. If you chose to build PARIDE
17 support into your kernel, you may answer Y here to build in the
18 parallel port IDE driver, otherwise you should answer M to build
19 it as a loadable module. The module will be called pd. You
20 must also have at least one parallel port protocol driver in your
21 system. Among the devices supported by this driver are the SyQuest
22 EZ-135, EZ-230 and SparQ drives, the Avatar Shark and the backpack
23 hard drives from MicroSolutions.
24
25config PARIDE_PCD
26 tristate "Parallel port ATAPI CD-ROMs"
27 depends on PARIDE
28 ---help---
29 This option enables the high-level driver for ATAPI CD-ROM devices
30 connected through a parallel port. If you chose to build PARIDE
31 support into your kernel, you may answer Y here to build in the
32 parallel port ATAPI CD-ROM driver, otherwise you should answer M to
33 build it as a loadable module. The module will be called pcd. You
34 must also have at least one parallel port protocol driver in your
35 system. Among the devices supported by this driver are the
36 MicroSolutions backpack CD-ROM drives and the Freecom Power CD. If
37 you have such a CD-ROM drive, you should also say Y or M to "ISO
38 9660 CD-ROM file system support" below, because that's the file
39 system used on CD-ROMs.
40
41config PARIDE_PF
42 tristate "Parallel port ATAPI disks"
43 depends on PARIDE
44 help
45 This option enables the high-level driver for ATAPI disk devices
46 connected through a parallel port. If you chose to build PARIDE
47 support into your kernel, you may answer Y here to build in the
48 parallel port ATAPI disk driver, otherwise you should answer M
49 to build it as a loadable module. The module will be called pf.
50 You must also have at least one parallel port protocol driver in
51 your system. Among the devices supported by this driver are the
52 MicroSolutions backpack PD/CD drive and the Imation Superdisk
53 LS-120 drive.
54
55config PARIDE_PT
56 tristate "Parallel port ATAPI tapes"
57 depends on PARIDE
58 help
59 This option enables the high-level driver for ATAPI tape devices
60 connected through a parallel port. If you chose to build PARIDE
61 support into your kernel, you may answer Y here to build in the
62 parallel port ATAPI disk driver, otherwise you should answer M
63 to build it as a loadable module. The module will be called pt.
64 You must also have at least one parallel port protocol driver in
65 your system. Among the devices supported by this driver is the
66 parallel port version of the HP 5GB drive.
67
68config PARIDE_PG
69 tristate "Parallel port generic ATAPI devices"
70 depends on PARIDE
71 ---help---
72 This option enables a special high-level driver for generic ATAPI
73 devices connected through a parallel port. The driver allows user
74 programs, such as cdrtools, to send ATAPI commands directly to a
75 device.
76
77 If you chose to build PARIDE support into your kernel, you may
78 answer Y here to build in the parallel port generic ATAPI driver,
79 otherwise you should answer M to build it as a loadable module. The
80 module will be called pg.
81
82 You must also have at least one parallel port protocol driver in
83 your system.
84
85 This driver implements an API loosely related to the generic SCSI
86 driver. See <file:include/linux/pg.h>. for details.
87
88 You can obtain the most recent version of cdrtools from
89 <ftp://ftp.berlios.de/pub/cdrecord/>. Versions 1.6.1a3 and
90 later fully support this driver.
91
92comment "Parallel IDE protocol modules"
93 depends on PARIDE
94
95config PARIDE_ATEN
96 tristate "ATEN EH-100 protocol"
97 depends on PARIDE
98 help
99 This option enables support for the ATEN EH-100 parallel port IDE
100 protocol. This protocol is used in some inexpensive low performance
101 parallel port kits made in Hong Kong. If you chose to build PARIDE
102 support into your kernel, you may answer Y here to build in the
103 protocol driver, otherwise you should answer M to build it as a
104 loadable module. The module will be called aten. You must also
105 have a high-level driver for the type of device that you want to
106 support.
107
108config PARIDE_BPCK
109 tristate "MicroSolutions backpack (Series 5) protocol"
110 depends on PARIDE
111 ---help---
112 This option enables support for the Micro Solutions BACKPACK
113 parallel port Series 5 IDE protocol. (Most BACKPACK drives made
114 before 1999 were Series 5) Series 5 drives will NOT always have the
115 Series noted on the bottom of the drive. Series 6 drivers will.
116
117 In other words, if your BACKPACK drive doesn't say "Series 6" on the
118 bottom, enable this option.
119
120 If you chose to build PARIDE support into your kernel, you may
121 answer Y here to build in the protocol driver, otherwise you should
122 answer M to build it as a loadable module. The module will be
123 called bpck. You must also have a high-level driver for the type
124 of device that you want to support.
125
126config PARIDE_BPCK6
127 tristate "MicroSolutions backpack (Series 6) protocol"
128 depends on PARIDE && !64BIT
129 ---help---
130 This option enables support for the Micro Solutions BACKPACK
131 parallel port Series 6 IDE protocol. (Most BACKPACK drives made
132 after 1999 were Series 6) Series 6 drives will have the Series noted
133 on the bottom of the drive. Series 5 drivers don't always have it
134 noted.
135
136 In other words, if your BACKPACK drive says "Series 6" on the
137 bottom, enable this option.
138
139 If you chose to build PARIDE support into your kernel, you may
140 answer Y here to build in the protocol driver, otherwise you should
141 answer M to build it as a loadable module. The module will be
142 called bpck6. You must also have a high-level driver for the type
143 of device that you want to support.
144
145config PARIDE_COMM
146 tristate "DataStor Commuter protocol"
147 depends on PARIDE
148 help
149 This option enables support for the Commuter parallel port IDE
150 protocol from DataStor. If you chose to build PARIDE support
151 into your kernel, you may answer Y here to build in the protocol
152 driver, otherwise you should answer M to build it as a loadable
153 module. The module will be called comm. You must also have
154 a high-level driver for the type of device that you want to support.
155
156config PARIDE_DSTR
157 tristate "DataStor EP-2000 protocol"
158 depends on PARIDE
159 help
160 This option enables support for the EP-2000 parallel port IDE
161 protocol from DataStor. If you chose to build PARIDE support
162 into your kernel, you may answer Y here to build in the protocol
163 driver, otherwise you should answer M to build it as a loadable
164 module. The module will be called dstr. You must also have
165 a high-level driver for the type of device that you want to support.
166
167config PARIDE_FIT2
168 tristate "FIT TD-2000 protocol"
169 depends on PARIDE
170 help
171 This option enables support for the TD-2000 parallel port IDE
172 protocol from Fidelity International Technology. This is a simple
173 (low speed) adapter that is used in some portable hard drives. If
174 you chose to build PARIDE support into your kernel, you may answer Y
175 here to build in the protocol driver, otherwise you should answer M
176 to build it as a loadable module. The module will be called ktti.
177 You must also have a high-level driver for the type of device that
178 you want to support.
179
180config PARIDE_FIT3
181 tristate "FIT TD-3000 protocol"
182 depends on PARIDE
183 help
184 This option enables support for the TD-3000 parallel port IDE
185 protocol from Fidelity International Technology. This protocol is
186 used in newer models of their portable disk, CD-ROM and PD/CD
187 devices. If you chose to build PARIDE support into your kernel, you
188 may answer Y here to build in the protocol driver, otherwise you
189 should answer M to build it as a loadable module. The module will be
190 called fit3. You must also have a high-level driver for the type
191 of device that you want to support.
192
193config PARIDE_EPAT
194 tristate "Shuttle EPAT/EPEZ protocol"
195 depends on PARIDE
196 help
197 This option enables support for the EPAT parallel port IDE protocol.
198 EPAT is a parallel port IDE adapter manufactured by Shuttle
199 Technology and widely used in devices from major vendors such as
200 Hewlett-Packard, SyQuest, Imation and Avatar. If you chose to build
201 PARIDE support into your kernel, you may answer Y here to build in
202 the protocol driver, otherwise you should answer M to build it as a
203 loadable module. The module will be called epat. You must also
204 have a high-level driver for the type of device that you want to
205 support.
206
207config PARIDE_EPATC8
208 bool "Support c7/c8 chips (EXPERIMENTAL)"
209 depends on PARIDE_EPAT && EXPERIMENTAL
210 help
211 This option enables support for the newer Shuttle EP1284 (aka c7 and
212 c8) chip. You need this if you are using any recent Imation SuperDisk
213 (LS-120) drive.
214
215config PARIDE_EPIA
216 tristate "Shuttle EPIA protocol"
217 depends on PARIDE
218 help
219 This option enables support for the (obsolete) EPIA parallel port
220 IDE protocol from Shuttle Technology. This adapter can still be
221 found in some no-name kits. If you chose to build PARIDE support
222 into your kernel, you may answer Y here to build in the protocol
223 driver, otherwise you should answer M to build it as a loadable
224 module. The module will be called epia. You must also have a
225 high-level driver for the type of device that you want to support.
226
227config PARIDE_FRIQ
228 tristate "Freecom IQ ASIC-2 protocol"
229 depends on PARIDE
230 help
231 This option enables support for version 2 of the Freecom IQ parallel
232 port IDE adapter. This adapter is used by the Maxell Superdisk
233 drive. If you chose to build PARIDE support into your kernel, you
234 may answer Y here to build in the protocol driver, otherwise you
235 should answer M to build it as a loadable module. The module will be
236 called friq. You must also have a high-level driver for the type
237 of device that you want to support.
238
239config PARIDE_FRPW
240 tristate "FreeCom power protocol"
241 depends on PARIDE
242 help
243 This option enables support for the Freecom power parallel port IDE
244 protocol. If you chose to build PARIDE support into your kernel, you
245 may answer Y here to build in the protocol driver, otherwise you
246 should answer M to build it as a loadable module. The module will be
247 called frpw. You must also have a high-level driver for the type
248 of device that you want to support.
249
250config PARIDE_KBIC
251 tristate "KingByte KBIC-951A/971A protocols"
252 depends on PARIDE
253 help
254 This option enables support for the KBIC-951A and KBIC-971A parallel
255 port IDE protocols from KingByte Information Corp. KingByte's
256 adapters appear in many no-name portable disk and CD-ROM products,
257 especially in Europe. If you chose to build PARIDE support into your
258 kernel, you may answer Y here to build in the protocol driver,
259 otherwise you should answer M to build it as a loadable module. The
260 module will be called kbic. You must also have a high-level driver
261 for the type of device that you want to support.
262
263config PARIDE_KTTI
264 tristate "KT PHd protocol"
265 depends on PARIDE
266 help
267 This option enables support for the "PHd" parallel port IDE protocol
268 from KT Technology. This is a simple (low speed) adapter that is
269 used in some 2.5" portable hard drives. If you chose to build PARIDE
270 support into your kernel, you may answer Y here to build in the
271 protocol driver, otherwise you should answer M to build it as a
272 loadable module. The module will be called ktti. You must also
273 have a high-level driver for the type of device that you want to
274 support.
275
276config PARIDE_ON20
277 tristate "OnSpec 90c20 protocol"
278 depends on PARIDE
279 help
280 This option enables support for the (obsolete) 90c20 parallel port
281 IDE protocol from OnSpec (often marketed under the ValuStore brand
282 name). If you chose to build PARIDE support into your kernel, you
283 may answer Y here to build in the protocol driver, otherwise you
284 should answer M to build it as a loadable module. The module will
285 be called on20. You must also have a high-level driver for the
286 type of device that you want to support.
287
288config PARIDE_ON26
289 tristate "OnSpec 90c26 protocol"
290 depends on PARIDE
291 help
292 This option enables support for the 90c26 parallel port IDE protocol
293 from OnSpec Electronics (often marketed under the ValuStore brand
294 name). If you chose to build PARIDE support into your kernel, you
295 may answer Y here to build in the protocol driver, otherwise you
296 should answer M to build it as a loadable module. The module will be
297 called on26. You must also have a high-level driver for the type
298 of device that you want to support.
299
300
301
