linux/drivers/hwmon/thmc50.c
<<
>>
Prefs
   1/*
   2    thmc50.c - Part of lm_sensors, Linux kernel modules for hardware
   3             monitoring
   4    Copyright (C) 2007 Krzysztof Helt <krzysztof.h1@wp.pl>
   5    Based on 2.4 driver by Frodo Looijaard <frodol@dds.nl> and
   6    Philip Edelbrock <phil@netroedge.com>
   7
   8    This program is free software; you can redistribute it and/or modify
   9    it under the terms of the GNU General Public License as published by
  10    the Free Software Foundation; either version 2 of the License, or
  11    (at your option) any later version.
  12
  13    This program is distributed in the hope that it will be useful,
  14    but WITHOUT ANY WARRANTY; without even the implied warranty of
  15    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16    GNU General Public License for more details.
  17
  18    You should have received a copy of the GNU General Public License
  19    along with this program; if not, write to the Free Software
  20    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21*/
  22
  23#include <linux/module.h>
  24#include <linux/init.h>
  25#include <linux/slab.h>
  26#include <linux/i2c.h>
  27#include <linux/hwmon.h>
  28#include <linux/hwmon-sysfs.h>
  29#include <linux/err.h>
  30#include <linux/mutex.h>
  31
  32MODULE_LICENSE("GPL");
  33
  34/* Addresses to scan */
  35static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
  36
  37/* Insmod parameters */
  38enum chips { thmc50, adm1022 };
  39
  40static unsigned short adm1022_temp3[16];
  41static unsigned int adm1022_temp3_num;
  42module_param_array(adm1022_temp3, ushort, &adm1022_temp3_num, 0);
  43MODULE_PARM_DESC(adm1022_temp3, "List of adapter,address pairs "
  44                        "to enable 3rd temperature (ADM1022 only)");
  45
  46/* Many THMC50 constants specified below */
  47
  48/* The THMC50 registers */
  49#define THMC50_REG_CONF                         0x40
  50#define THMC50_REG_COMPANY_ID                   0x3E
  51#define THMC50_REG_DIE_CODE                     0x3F
  52#define THMC50_REG_ANALOG_OUT                   0x19
  53/*
  54 * The mirror status register cannot be used as
  55 * reading it does not clear alarms.
  56 */
  57#define THMC50_REG_INTR                         0x41
  58
  59static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
  60static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
  61static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
  62static const u8 THMC50_REG_TEMP_CRITICAL[] = { 0x13, 0x14, 0x14 };
  63static const u8 THMC50_REG_TEMP_DEFAULT[] = { 0x17, 0x18, 0x18 };
  64
  65#define THMC50_REG_CONF_nFANOFF                 0x20
  66#define THMC50_REG_CONF_PROGRAMMED              0x08
  67
  68/* Each client has this additional data */
  69struct thmc50_data {
  70        struct device *hwmon_dev;
  71
  72        struct mutex update_lock;
  73        enum chips type;
  74        unsigned long last_updated;     /* In jiffies */
  75        char has_temp3;         /* !=0 if it is ADM1022 in temp3 mode */
  76        char valid;             /* !=0 if following fields are valid */
  77
  78        /* Register values */
  79        s8 temp_input[3];
  80        s8 temp_max[3];
  81        s8 temp_min[3];
  82        s8 temp_critical[3];
  83        u8 analog_out;
  84        u8 alarms;
  85};
  86
  87static int thmc50_detect(struct i2c_client *client,
  88                         struct i2c_board_info *info);
  89static int thmc50_probe(struct i2c_client *client,
  90                        const struct i2c_device_id *id);
  91static int thmc50_remove(struct i2c_client *client);
  92static void thmc50_init_client(struct i2c_client *client);
  93static struct thmc50_data *thmc50_update_device(struct device *dev);
  94
  95static const struct i2c_device_id thmc50_id[] = {
  96        { "adm1022", adm1022 },
  97        { "thmc50", thmc50 },
  98        { }
  99};
 100MODULE_DEVICE_TABLE(i2c, thmc50_id);
 101
 102static struct i2c_driver thmc50_driver = {
 103        .class = I2C_CLASS_HWMON,
 104        .driver = {
 105                .name = "thmc50",
 106        },
 107        .probe = thmc50_probe,
 108        .remove = thmc50_remove,
 109        .id_table = thmc50_id,
 110        .detect = thmc50_detect,
 111        .address_list = normal_i2c,
 112};
 113
 114static ssize_t show_analog_out(struct device *dev,
 115                               struct device_attribute *attr, char *buf)
 116{
 117        struct thmc50_data *data = thmc50_update_device(dev);
 118        return sprintf(buf, "%d\n", data->analog_out);
 119}
 120
 121static ssize_t set_analog_out(struct device *dev,
 122                              struct device_attribute *attr,
 123                              const char *buf, size_t count)
 124{
 125        struct i2c_client *client = to_i2c_client(dev);
 126        struct thmc50_data *data = i2c_get_clientdata(client);
 127        int tmp = simple_strtoul(buf, NULL, 10);
 128        int config;
 129
 130        mutex_lock(&data->update_lock);
 131        data->analog_out = SENSORS_LIMIT(tmp, 0, 255);
 132        i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 133                                  data->analog_out);
 134
 135        config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 136        if (data->analog_out == 0)
 137                config &= ~THMC50_REG_CONF_nFANOFF;
 138        else
 139                config |= THMC50_REG_CONF_nFANOFF;
 140        i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 141
 142        mutex_unlock(&data->update_lock);
 143        return count;
 144}
 145
 146/* There is only one PWM mode = DC */
 147static ssize_t show_pwm_mode(struct device *dev, struct device_attribute *attr,
 148                             char *buf)
 149{
 150        return sprintf(buf, "0\n");
 151}
 152
 153/* Temperatures */
 154static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
 155                         char *buf)
 156{
 157        int nr = to_sensor_dev_attr(attr)->index;
 158        struct thmc50_data *data = thmc50_update_device(dev);
 159        return sprintf(buf, "%d\n", data->temp_input[nr] * 1000);
 160}
 161
 162static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
 163                             char *buf)
 164{
 165        int nr = to_sensor_dev_attr(attr)->index;
 166        struct thmc50_data *data = thmc50_update_device(dev);
 167        return sprintf(buf, "%d\n", data->temp_min[nr] * 1000);
 168}
 169
 170static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
 171                            const char *buf, size_t count)
 172{
 173        int nr = to_sensor_dev_attr(attr)->index;
 174        struct i2c_client *client = to_i2c_client(dev);
 175        struct thmc50_data *data = i2c_get_clientdata(client);
 176        int val = simple_strtol(buf, NULL, 10);
 177
 178        mutex_lock(&data->update_lock);
 179        data->temp_min[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
 180        i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MIN[nr],
 181                                  data->temp_min[nr]);
 182        mutex_unlock(&data->update_lock);
 183        return count;
 184}
 185
 186static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
 187                             char *buf)
 188{
 189        int nr = to_sensor_dev_attr(attr)->index;
 190        struct thmc50_data *data = thmc50_update_device(dev);
 191        return sprintf(buf, "%d\n", data->temp_max[nr] * 1000);
 192}
 193
 194static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
 195                            const char *buf, size_t count)
 196{
 197        int nr = to_sensor_dev_attr(attr)->index;
 198        struct i2c_client *client = to_i2c_client(dev);
 199        struct thmc50_data *data = i2c_get_clientdata(client);
 200        int val = simple_strtol(buf, NULL, 10);
 201
 202        mutex_lock(&data->update_lock);
 203        data->temp_max[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
 204        i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MAX[nr],
 205                                  data->temp_max[nr]);
 206        mutex_unlock(&data->update_lock);
 207        return count;
 208}
 209
 210static ssize_t show_temp_critical(struct device *dev,
 211                                  struct device_attribute *attr,
 212                                  char *buf)
 213{
 214        int nr = to_sensor_dev_attr(attr)->index;
 215        struct thmc50_data *data = thmc50_update_device(dev);
 216        return sprintf(buf, "%d\n", data->temp_critical[nr] * 1000);
 217}
 218
 219static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
 220                          char *buf)
 221{
 222        int index = to_sensor_dev_attr(attr)->index;
 223        struct thmc50_data *data = thmc50_update_device(dev);
 224
 225        return sprintf(buf, "%u\n", (data->alarms >> index) & 1);
 226}
 227
 228#define temp_reg(offset)                                                \
 229static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp,     \
 230                        NULL, offset - 1);                              \
 231static SENSOR_DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR,        \
 232                        show_temp_min, set_temp_min, offset - 1);       \
 233static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR,        \
 234                        show_temp_max, set_temp_max, offset - 1);       \
 235static SENSOR_DEVICE_ATTR(temp##offset##_crit, S_IRUGO,                 \
 236                        show_temp_critical, NULL, offset - 1);
 237
 238temp_reg(1);
 239temp_reg(2);
 240temp_reg(3);
 241
 242static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0);
 243static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
 244static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 1);
 245static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 7);
 246static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 2);
 247
 248static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_analog_out,
 249                          set_analog_out, 0);
 250static SENSOR_DEVICE_ATTR(pwm1_mode, S_IRUGO, show_pwm_mode, NULL, 0);
 251
 252static struct attribute *thmc50_attributes[] = {
 253        &sensor_dev_attr_temp1_max.dev_attr.attr,
 254        &sensor_dev_attr_temp1_min.dev_attr.attr,
 255        &sensor_dev_attr_temp1_input.dev_attr.attr,
 256        &sensor_dev_attr_temp1_crit.dev_attr.attr,
 257        &sensor_dev_attr_temp1_alarm.dev_attr.attr,
 258        &sensor_dev_attr_temp2_max.dev_attr.attr,
 259        &sensor_dev_attr_temp2_min.dev_attr.attr,
 260        &sensor_dev_attr_temp2_input.dev_attr.attr,
 261        &sensor_dev_attr_temp2_crit.dev_attr.attr,
 262        &sensor_dev_attr_temp2_alarm.dev_attr.attr,
 263        &sensor_dev_attr_temp2_fault.dev_attr.attr,
 264        &sensor_dev_attr_pwm1.dev_attr.attr,
 265        &sensor_dev_attr_pwm1_mode.dev_attr.attr,
 266        NULL
 267};
 268
 269static const struct attribute_group thmc50_group = {
 270        .attrs = thmc50_attributes,
 271};
 272
 273/* for ADM1022 3rd temperature mode */
 274static struct attribute *temp3_attributes[] = {
 275        &sensor_dev_attr_temp3_max.dev_attr.attr,
 276        &sensor_dev_attr_temp3_min.dev_attr.attr,
 277        &sensor_dev_attr_temp3_input.dev_attr.attr,
 278        &sensor_dev_attr_temp3_crit.dev_attr.attr,
 279        &sensor_dev_attr_temp3_alarm.dev_attr.attr,
 280        &sensor_dev_attr_temp3_fault.dev_attr.attr,
 281        NULL
 282};
 283
 284static const struct attribute_group temp3_group = {
 285        .attrs = temp3_attributes,
 286};
 287
 288/* Return 0 if detection is successful, -ENODEV otherwise */
 289static int thmc50_detect(struct i2c_client *client,
 290                         struct i2c_board_info *info)
 291{
 292        unsigned company;
 293        unsigned revision;
 294        unsigned config;
 295        struct i2c_adapter *adapter = client->adapter;
 296        const char *type_name;
 297
 298        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
 299                pr_debug("thmc50: detect failed, "
 300                         "smbus byte data not supported!\n");
 301                return -ENODEV;
 302        }
 303
 304        pr_debug("thmc50: Probing for THMC50 at 0x%2X on bus %d\n",
 305                 client->addr, i2c_adapter_id(client->adapter));
 306
 307        company = i2c_smbus_read_byte_data(client, THMC50_REG_COMPANY_ID);
 308        revision = i2c_smbus_read_byte_data(client, THMC50_REG_DIE_CODE);
 309        config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 310        if (revision < 0xc0 || (config & 0x10))
 311                return -ENODEV;
 312
 313        if (company == 0x41) {
 314                int id = i2c_adapter_id(client->adapter);
 315                int i;
 316
 317                type_name = "adm1022";
 318                for (i = 0; i + 1 < adm1022_temp3_num; i += 2)
 319                        if (adm1022_temp3[i] == id &&
 320                            adm1022_temp3[i + 1] == client->addr) {
 321                                /* enable 2nd remote temp */
 322                                config |= (1 << 7);
 323                                i2c_smbus_write_byte_data(client,
 324                                                          THMC50_REG_CONF,
 325                                                          config);
 326                                break;
 327                        }
 328        } else if (company == 0x49) {
 329                type_name = "thmc50";
 330        } else {
 331                pr_debug("thmc50: Detection of THMC50/ADM1022 failed\n");
 332                return -ENODEV;
 333        }
 334
 335        pr_debug("thmc50: Detected %s (version %x, revision %x)\n",
 336                 type_name, (revision >> 4) - 0xc, revision & 0xf);
 337
 338        strlcpy(info->type, type_name, I2C_NAME_SIZE);
 339
 340        return 0;
 341}
 342
 343static int thmc50_probe(struct i2c_client *client,
 344                        const struct i2c_device_id *id)
 345{
 346        struct thmc50_data *data;
 347        int err;
 348
 349        data = kzalloc(sizeof(struct thmc50_data), GFP_KERNEL);
 350        if (!data) {
 351                pr_debug("thmc50: detect failed, kzalloc failed!\n");
 352                err = -ENOMEM;
 353                goto exit;
 354        }
 355
 356        i2c_set_clientdata(client, data);
 357        data->type = id->driver_data;
 358        mutex_init(&data->update_lock);
 359
 360        thmc50_init_client(client);
 361
 362        /* Register sysfs hooks */
 363        if ((err = sysfs_create_group(&client->dev.kobj, &thmc50_group)))
 364                goto exit_free;
 365
 366        /* Register ADM1022 sysfs hooks */
 367        if (data->has_temp3)
 368                if ((err = sysfs_create_group(&client->dev.kobj,
 369                                              &temp3_group)))
 370                        goto exit_remove_sysfs_thmc50;
 371
 372        /* Register a new directory entry with module sensors */
 373        data->hwmon_dev = hwmon_device_register(&client->dev);
 374        if (IS_ERR(data->hwmon_dev)) {
 375                err = PTR_ERR(data->hwmon_dev);
 376                goto exit_remove_sysfs;
 377        }
 378
 379        return 0;
 380
 381exit_remove_sysfs:
 382        if (data->has_temp3)
 383                sysfs_remove_group(&client->dev.kobj, &temp3_group);
 384exit_remove_sysfs_thmc50:
 385        sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 386exit_free:
 387        kfree(data);
 388exit:
 389        return err;
 390}
 391
 392static int thmc50_remove(struct i2c_client *client)
 393{
 394        struct thmc50_data *data = i2c_get_clientdata(client);
 395
 396        hwmon_device_unregister(data->hwmon_dev);
 397        sysfs_remove_group(&client->dev.kobj, &thmc50_group);
 398        if (data->has_temp3)
 399                sysfs_remove_group(&client->dev.kobj, &temp3_group);
 400
 401        kfree(data);
 402
 403        return 0;
 404}
 405
 406static void thmc50_init_client(struct i2c_client *client)
 407{
 408        struct thmc50_data *data = i2c_get_clientdata(client);
 409        int config;
 410
 411        data->analog_out = i2c_smbus_read_byte_data(client,
 412                                                    THMC50_REG_ANALOG_OUT);
 413        /* set up to at least 1 */
 414        if (data->analog_out == 0) {
 415                data->analog_out = 1;
 416                i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
 417                                          data->analog_out);
 418        }
 419        config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 420        config |= 0x1;  /* start the chip if it is in standby mode */
 421        if (data->type == adm1022 && (config & (1 << 7)))
 422                data->has_temp3 = 1;
 423        i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
 424}
 425
 426static struct thmc50_data *thmc50_update_device(struct device *dev)
 427{
 428        struct i2c_client *client = to_i2c_client(dev);
 429        struct thmc50_data *data = i2c_get_clientdata(client);
 430        int timeout = HZ / 5 + (data->type == thmc50 ? HZ : 0);
 431
 432        mutex_lock(&data->update_lock);
 433
 434        if (time_after(jiffies, data->last_updated + timeout)
 435            || !data->valid) {
 436
 437                int temps = data->has_temp3 ? 3 : 2;
 438                int i;
 439                int prog = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
 440
 441                prog &= THMC50_REG_CONF_PROGRAMMED;
 442
 443                for (i = 0; i < temps; i++) {
 444                        data->temp_input[i] = i2c_smbus_read_byte_data(client,
 445                                                THMC50_REG_TEMP[i]);
 446                        data->temp_max[i] = i2c_smbus_read_byte_data(client,
 447                                                THMC50_REG_TEMP_MAX[i]);
 448                        data->temp_min[i] = i2c_smbus_read_byte_data(client,
 449                                                THMC50_REG_TEMP_MIN[i]);
 450                        data->temp_critical[i] =
 451                                i2c_smbus_read_byte_data(client,
 452                                        prog ? THMC50_REG_TEMP_CRITICAL[i]
 453                                             : THMC50_REG_TEMP_DEFAULT[i]);
 454                }
 455                data->analog_out =
 456                    i2c_smbus_read_byte_data(client, THMC50_REG_ANALOG_OUT);
 457                data->alarms =
 458                    i2c_smbus_read_byte_data(client, THMC50_REG_INTR);
 459                data->last_updated = jiffies;
 460                data->valid = 1;
 461        }
 462
 463        mutex_unlock(&data->update_lock);
 464
 465        return data;
 466}
 467
 468static int __init sm_thmc50_init(void)
 469{
 470        return i2c_add_driver(&thmc50_driver);
 471}
 472
 473static void __exit sm_thmc50_exit(void)
 474{
 475        i2c_del_driver(&thmc50_driver);
 476}
 477
 478MODULE_AUTHOR("Krzysztof Helt <krzysztof.h1@wp.pl>");
 479MODULE_DESCRIPTION("THMC50 driver");
 480
 481module_init(sm_thmc50_init);
 482module_exit(sm_thmc50_exit);
 483