linux/drivers/staging/iio/imu/adis16300_core.c
<<
>>
Prefs
   1/*
   2 * ADIS16300 Four Degrees of Freedom Inertial Sensor Driver
   3 *
   4 * Copyright 2010 Analog Devices Inc.
   5 *
   6 * Licensed under the GPL-2 or later.
   7 */
   8
   9#include <linux/interrupt.h>
  10#include <linux/irq.h>
  11#include <linux/gpio.h>
  12#include <linux/delay.h>
  13#include <linux/mutex.h>
  14#include <linux/device.h>
  15#include <linux/kernel.h>
  16#include <linux/spi/spi.h>
  17#include <linux/slab.h>
  18#include <linux/sysfs.h>
  19#include <linux/list.h>
  20
  21#include "../iio.h"
  22#include "../sysfs.h"
  23#include "../ring_generic.h"
  24#include "../accel/accel.h"
  25#include "../accel/inclinometer.h"
  26#include "../gyro/gyro.h"
  27#include "../adc/adc.h"
  28
  29#include "adis16300.h"
  30
  31#define DRIVER_NAME             "adis16300"
  32
  33static int adis16300_check_status(struct device *dev);
  34
  35/**
  36 * adis16300_spi_write_reg_8() - write single byte to a register
  37 * @dev: device associated with child of actual device (iio_dev or iio_trig)
  38 * @reg_address: the address of the register to be written
  39 * @val: the value to write
  40 **/
  41static int adis16300_spi_write_reg_8(struct device *dev,
  42                u8 reg_address,
  43                u8 val)
  44{
  45        int ret;
  46        struct iio_dev *indio_dev = dev_get_drvdata(dev);
  47        struct adis16300_state *st = iio_dev_get_devdata(indio_dev);
  48
  49        mutex_lock(&st->buf_lock);
  50        st->tx[0] = ADIS16300_WRITE_REG(reg_address);
  51        st->tx[1] = val;
  52
  53        ret = spi_write(st->us, st->tx, 2);
  54        mutex_unlock(&st->buf_lock);
  55
  56        return ret;
  57}
  58
  59/**
  60 * adis16300_spi_write_reg_16() - write 2 bytes to a pair of registers
  61 * @dev: device associated with child of actual device (iio_dev or iio_trig)
  62 * @reg_address: the address of the lower of the two registers. Second register
  63 *               is assumed to have address one greater.
  64 * @val: value to be written
  65 **/
  66static int adis16300_spi_write_reg_16(struct device *dev,
  67                u8 lower_reg_address,
  68                u16 value)
  69{
  70        int ret;
  71        struct spi_message msg;
  72        struct iio_dev *indio_dev = dev_get_drvdata(dev);
  73        struct adis16300_state *st = iio_dev_get_devdata(indio_dev);
  74        struct spi_transfer xfers[] = {
  75                {
  76                        .tx_buf = st->tx,
  77                        .bits_per_word = 8,
  78                        .len = 2,
  79                        .cs_change = 1,
  80                        .delay_usecs = 75,
  81                }, {
  82                        .tx_buf = st->tx + 2,
  83                        .bits_per_word = 8,
  84                        .len = 2,
  85                        .cs_change = 1,
  86                        .delay_usecs = 75,
  87                },
  88        };
  89
  90        mutex_lock(&st->buf_lock);
  91        st->tx[0] = ADIS16300_WRITE_REG(lower_reg_address);
  92        st->tx[1] = value & 0xFF;
  93        st->tx[2] = ADIS16300_WRITE_REG(lower_reg_address + 1);
  94        st->tx[3] = (value >> 8) & 0xFF;
  95
  96        spi_message_init(&msg);
  97        spi_message_add_tail(&xfers[0], &msg);
  98        spi_message_add_tail(&xfers[1], &msg);
  99        ret = spi_sync(st->us, &msg);
 100        mutex_unlock(&st->buf_lock);
 101
 102        return ret;
 103}
 104
 105/**
 106 * adis16300_spi_read_reg_16() - read 2 bytes from a 16-bit register
 107 * @dev: device associated with child of actual device (iio_dev or iio_trig)
 108 * @reg_address: the address of the lower of the two registers. Second register
 109 *               is assumed to have address one greater.
 110 * @val: somewhere to pass back the value read
 111 **/
 112static int adis16300_spi_read_reg_16(struct device *dev,
 113                u8 lower_reg_address,
 114                u16 *val)
 115{
 116        struct spi_message msg;
 117        struct iio_dev *indio_dev = dev_get_drvdata(dev);
 118        struct adis16300_state *st = iio_dev_get_devdata(indio_dev);
 119        int ret;
 120        struct spi_transfer xfers[] = {
 121                {
 122                        .tx_buf = st->tx,
 123                        .bits_per_word = 8,
 124                        .len = 2,
 125                        .cs_change = 1,
 126                        .delay_usecs = 75,
 127                }, {
 128                        .rx_buf = st->rx,
 129                        .bits_per_word = 8,
 130                        .len = 2,
 131                        .cs_change = 1,
 132                        .delay_usecs = 75,
 133                },
 134        };
 135
 136        mutex_lock(&st->buf_lock);
 137        st->tx[0] = ADIS16300_READ_REG(lower_reg_address);
 138        st->tx[1] = 0;
 139        st->tx[2] = 0;
 140        st->tx[3] = 0;
 141
 142        spi_message_init(&msg);
 143        spi_message_add_tail(&xfers[0], &msg);
 144        spi_message_add_tail(&xfers[1], &msg);
 145        ret = spi_sync(st->us, &msg);
 146        if (ret) {
 147                dev_err(&st->us->dev,
 148                        "problem when reading 16 bit register 0x%02X",
 149                        lower_reg_address);
 150                goto error_ret;
 151        }
 152        *val = (st->rx[0] << 8) | st->rx[1];
 153
 154error_ret:
 155        mutex_unlock(&st->buf_lock);
 156        return ret;
 157}
 158
 159static ssize_t adis16300_spi_read_signed(struct device *dev,
 160                struct device_attribute *attr,
 161                char *buf,
 162                unsigned bits)
 163{
 164        int ret;
 165        s16 val = 0;
 166        unsigned shift = 16 - bits;
 167        struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
 168
 169        ret = adis16300_spi_read_reg_16(dev, this_attr->address, (u16 *)&val);
 170        if (ret)
 171                return ret;
 172
 173        if (val & ADIS16300_ERROR_ACTIVE)
 174                adis16300_check_status(dev);
 175        val = ((s16)(val << shift) >> shift);
 176        return sprintf(buf, "%d\n", val);
 177}
 178
 179static ssize_t adis16300_read_12bit_unsigned(struct device *dev,
 180                struct device_attribute *attr,
 181                char *buf)
 182{
 183        int ret;
 184        u16 val = 0;
 185        struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
 186
 187        ret = adis16300_spi_read_reg_16(dev, this_attr->address, &val);
 188        if (ret)
 189                return ret;
 190
 191        if (val & ADIS16300_ERROR_ACTIVE)
 192                adis16300_check_status(dev);
 193
 194        return sprintf(buf, "%u\n", val & 0x0FFF);
 195}
 196
 197static ssize_t adis16300_read_14bit_unsigned(struct device *dev,
 198                struct device_attribute *attr,
 199                char *buf)
 200{
 201        int ret;
 202        u16 val = 0;
 203        struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
 204
 205        ret = adis16300_spi_read_reg_16(dev, this_attr->address, &val);
 206        if (ret)
 207                return ret;
 208
 209        if (val & ADIS16300_ERROR_ACTIVE)
 210                adis16300_check_status(dev);
 211
 212        return sprintf(buf, "%u\n", val & 0x3FFF);
 213}
 214
 215static ssize_t adis16300_read_14bit_signed(struct device *dev,
 216                struct device_attribute *attr,
 217                char *buf)
 218{
 219        struct iio_dev *indio_dev = dev_get_drvdata(dev);
 220        ssize_t ret;
 221
 222        /* Take the iio_dev status lock */
 223        mutex_lock(&indio_dev->mlock);
 224        ret =  adis16300_spi_read_signed(dev, attr, buf, 14);
 225        mutex_unlock(&indio_dev->mlock);
 226
 227        return ret;
 228}
 229
 230static ssize_t adis16300_read_12bit_signed(struct device *dev,
 231                struct device_attribute *attr,
 232                char *buf)
 233{
 234        struct iio_dev *indio_dev = dev_get_drvdata(dev);
 235        ssize_t ret;
 236
 237        /* Take the iio_dev status lock */
 238        mutex_lock(&indio_dev->mlock);
 239        ret =  adis16300_spi_read_signed(dev, attr, buf, 12);
 240        mutex_unlock(&indio_dev->mlock);
 241
 242        return ret;
 243}
 244
 245static ssize_t adis16300_read_13bit_signed(struct device *dev,
 246                struct device_attribute *attr,
 247                char *buf)
 248{
 249        struct iio_dev *indio_dev = dev_get_drvdata(dev);
 250        ssize_t ret;
 251
 252        /* Take the iio_dev status lock */
 253        mutex_lock(&indio_dev->mlock);
 254        ret =  adis16300_spi_read_signed(dev, attr, buf, 13);
 255        mutex_unlock(&indio_dev->mlock);
 256
 257        return ret;
 258}
 259
 260static ssize_t adis16300_write_16bit(struct device *dev,
 261                struct device_attribute *attr,
 262                const char *buf,
 263                size_t len)
 264{
 265        struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
 266        int ret;
 267        long val;
 268
 269        ret = strict_strtol(buf, 10, &val);
 270        if (ret)
 271                goto error_ret;
 272        ret = adis16300_spi_write_reg_16(dev, this_attr->address, val);
 273
 274error_ret:
 275        return ret ? ret : len;
 276}
 277
 278static ssize_t adis16300_read_frequency(struct device *dev,
 279                struct device_attribute *attr,
 280                char *buf)
 281{
 282        int ret, len = 0;
 283        u16 t;
 284        int sps;
 285        ret = adis16300_spi_read_reg_16(dev,
 286                        ADIS16300_SMPL_PRD,
 287                        &t);
 288        if (ret)
 289                return ret;
 290        sps =  (t & ADIS16300_SMPL_PRD_TIME_BASE) ? 53 : 1638;
 291        sps /= (t & ADIS16300_SMPL_PRD_DIV_MASK) + 1;
 292        len = sprintf(buf, "%d SPS\n", sps);
 293        return len;
 294}
 295
 296static ssize_t adis16300_write_frequency(struct device *dev,
 297                struct device_attribute *attr,
 298                const char *buf,
 299                size_t len)
 300{
 301        struct iio_dev *indio_dev = dev_get_drvdata(dev);
 302        struct adis16300_state *st = iio_dev_get_devdata(indio_dev);
 303        long val;
 304        int ret;
 305        u8 t;
 306
 307        ret = strict_strtol(buf, 10, &val);
 308        if (ret)
 309                return ret;
 310
 311        mutex_lock(&indio_dev->mlock);
 312
 313        t = (1638 / val);
 314        if (t > 0)
 315                t--;
 316        t &= ADIS16300_SMPL_PRD_DIV_MASK;
 317        if ((t & ADIS16300_SMPL_PRD_DIV_MASK) >= 0x0A)
 318                st->us->max_speed_hz = ADIS16300_SPI_SLOW;
 319        else
 320                st->us->max_speed_hz = ADIS16300_SPI_FAST;
 321
 322        ret = adis16300_spi_write_reg_8(dev,
 323                        ADIS16300_SMPL_PRD,
 324                        t);
 325
 326        mutex_unlock(&indio_dev->mlock);
 327
 328        return ret ? ret : len;
 329}
 330
 331static int adis16300_reset(struct device *dev)
 332{
 333        int ret;
 334        ret = adis16300_spi_write_reg_8(dev,
 335                        ADIS16300_GLOB_CMD,
 336                        ADIS16300_GLOB_CMD_SW_RESET);
 337        if (ret)
 338                dev_err(dev, "problem resetting device");
 339
 340        return ret;
 341}
 342
 343static ssize_t adis16300_write_reset(struct device *dev,
 344                struct device_attribute *attr,
 345                const char *buf, size_t len)
 346{
 347        if (len < 1)
 348                return -1;
 349        switch (buf[0]) {
 350        case '1':
 351        case 'y':
 352        case 'Y':
 353                return adis16300_reset(dev);
 354        }
 355        return -1;
 356}
 357
 358int adis16300_set_irq(struct device *dev, bool enable)
 359{
 360        int ret;
 361        u16 msc;
 362        ret = adis16300_spi_read_reg_16(dev, ADIS16300_MSC_CTRL, &msc);
 363        if (ret)
 364                goto error_ret;
 365
 366        msc |= ADIS16300_MSC_CTRL_DATA_RDY_POL_HIGH;
 367        msc &= ~ADIS16300_MSC_CTRL_DATA_RDY_DIO2;
 368        if (enable)
 369                msc |= ADIS16300_MSC_CTRL_DATA_RDY_EN;
 370        else
 371                msc &= ~ADIS16300_MSC_CTRL_DATA_RDY_EN;
 372
 373        ret = adis16300_spi_write_reg_16(dev, ADIS16300_MSC_CTRL, msc);
 374        if (ret)
 375                goto error_ret;
 376
 377error_ret:
 378        return ret;
 379}
 380
 381/* Power down the device */
 382static int adis16300_stop_device(struct device *dev)
 383{
 384        int ret;
 385        u16 val = ADIS16300_SLP_CNT_POWER_OFF;
 386
 387        ret = adis16300_spi_write_reg_16(dev, ADIS16300_SLP_CNT, val);
 388        if (ret)
 389                dev_err(dev, "problem with turning device off: SLP_CNT");
 390
 391        return ret;
 392}
 393
 394static int adis16300_self_test(struct device *dev)
 395{
 396        int ret;
 397        ret = adis16300_spi_write_reg_16(dev,
 398                        ADIS16300_MSC_CTRL,
 399                        ADIS16300_MSC_CTRL_MEM_TEST);
 400        if (ret) {
 401                dev_err(dev, "problem starting self test");
 402                goto err_ret;
 403        }
 404
 405        adis16300_check_status(dev);
 406
 407err_ret:
 408        return ret;
 409}
 410
 411static int adis16300_check_status(struct device *dev)
 412{
 413        u16 status;
 414        int ret;
 415
 416        ret = adis16300_spi_read_reg_16(dev, ADIS16300_DIAG_STAT, &status);
 417
 418        if (ret < 0) {
 419                dev_err(dev, "Reading status failed\n");
 420                goto error_ret;
 421        }
 422        ret = status;
 423        if (status & ADIS16300_DIAG_STAT_ZACCL_FAIL)
 424                dev_err(dev, "Z-axis accelerometer self-test failure\n");
 425        if (status & ADIS16300_DIAG_STAT_YACCL_FAIL)
 426                dev_err(dev, "Y-axis accelerometer self-test failure\n");
 427        if (status & ADIS16300_DIAG_STAT_XACCL_FAIL)
 428                dev_err(dev, "X-axis accelerometer self-test failure\n");
 429        if (status & ADIS16300_DIAG_STAT_XGYRO_FAIL)
 430                dev_err(dev, "X-axis gyroscope self-test failure\n");
 431        if (status & ADIS16300_DIAG_STAT_ALARM2)
 432                dev_err(dev, "Alarm 2 active\n");
 433        if (status & ADIS16300_DIAG_STAT_ALARM1)
 434                dev_err(dev, "Alarm 1 active\n");
 435        if (status & ADIS16300_DIAG_STAT_FLASH_CHK)
 436                dev_err(dev, "Flash checksum error\n");
 437        if (status & ADIS16300_DIAG_STAT_SELF_TEST)
 438                dev_err(dev, "Self test error\n");
 439        if (status & ADIS16300_DIAG_STAT_OVERFLOW)
 440                dev_err(dev, "Sensor overrange\n");
 441        if (status & ADIS16300_DIAG_STAT_SPI_FAIL)
 442                dev_err(dev, "SPI failure\n");
 443        if (status & ADIS16300_DIAG_STAT_FLASH_UPT)
 444                dev_err(dev, "Flash update failed\n");
 445        if (status & ADIS16300_DIAG_STAT_POWER_HIGH)
 446                dev_err(dev, "Power supply above 5.25V\n");
 447        if (status & ADIS16300_DIAG_STAT_POWER_LOW)
 448                dev_err(dev, "Power supply below 4.75V\n");
 449
 450error_ret:
 451        return ret;
 452}
 453
 454static int adis16300_initial_setup(struct adis16300_state *st)
 455{
 456        int ret;
 457        u16 smp_prd;
 458        struct device *dev = &st->indio_dev->dev;
 459
 460        /* use low spi speed for init */
 461        st->us->max_speed_hz = ADIS16300_SPI_SLOW;
 462        st->us->mode = SPI_MODE_3;
 463        spi_setup(st->us);
 464
 465        /* Disable IRQ */
 466        ret = adis16300_set_irq(dev, false);
 467        if (ret) {
 468                dev_err(dev, "disable irq failed");
 469                goto err_ret;
 470        }
 471
 472        /* Do self test */
 473        ret = adis16300_self_test(dev);
 474        if (ret) {
 475                dev_err(dev, "self test failure");
 476                goto err_ret;
 477        }
 478
 479        /* Read status register to check the result */
 480        ret = adis16300_check_status(dev);
 481        if (ret) {
 482                adis16300_reset(dev);
 483                dev_err(dev, "device not playing ball -> reset");
 484                msleep(ADIS16300_STARTUP_DELAY);
 485                ret = adis16300_check_status(dev);
 486                if (ret) {
 487                        dev_err(dev, "giving up");
 488                        goto err_ret;
 489                }
 490        }
 491
 492        printk(KERN_INFO DRIVER_NAME ": at CS%d (irq %d)\n",
 493                        st->us->chip_select, st->us->irq);
 494
 495        /* use high spi speed if possible */
 496        ret = adis16300_spi_read_reg_16(dev, ADIS16300_SMPL_PRD, &smp_prd);
 497        if (!ret && (smp_prd & ADIS16300_SMPL_PRD_DIV_MASK) < 0x0A) {
 498                st->us->max_speed_hz = ADIS16300_SPI_SLOW;
 499                spi_setup(st->us);
 500        }
 501
 502err_ret:
 503        return ret;
 504}
 505
 506static IIO_DEV_ATTR_GYRO_X_CALIBBIAS(S_IWUSR | S_IRUGO,
 507                adis16300_read_12bit_signed,
 508                adis16300_write_16bit,
 509                ADIS16300_XGYRO_OFF);
 510
 511static IIO_DEV_ATTR_ACCEL_X_CALIBBIAS(S_IWUSR | S_IRUGO,
 512                adis16300_read_12bit_signed,
 513                adis16300_write_16bit,
 514                ADIS16300_XACCL_OFF);
 515
 516static IIO_DEV_ATTR_ACCEL_Y_CALIBBIAS(S_IWUSR | S_IRUGO,
 517                adis16300_read_12bit_signed,
 518                adis16300_write_16bit,
 519                ADIS16300_YACCL_OFF);
 520
 521static IIO_DEV_ATTR_ACCEL_Z_CALIBBIAS(S_IWUSR | S_IRUGO,
 522                adis16300_read_12bit_signed,
 523                adis16300_write_16bit,
 524                ADIS16300_ZACCL_OFF);
 525
 526static IIO_DEV_ATTR_IN_NAMED_RAW(0, supply, adis16300_read_14bit_unsigned,
 527                           ADIS16300_SUPPLY_OUT);
 528static IIO_CONST_ATTR_IN_NAMED_SCALE(0, supply, "0.00242");
 529
 530static IIO_DEV_ATTR_GYRO_X(adis16300_read_14bit_signed,
 531                ADIS16300_XGYRO_OUT);
 532static IIO_CONST_ATTR_GYRO_SCALE("0.000872664");
 533
 534static IIO_DEV_ATTR_ACCEL_X(adis16300_read_14bit_signed,
 535                ADIS16300_XACCL_OUT);
 536static IIO_DEV_ATTR_ACCEL_Y(adis16300_read_14bit_signed,
 537                ADIS16300_YACCL_OUT);
 538static IIO_DEV_ATTR_ACCEL_Z(adis16300_read_14bit_signed,
 539                ADIS16300_ZACCL_OUT);
 540static IIO_CONST_ATTR_ACCEL_SCALE("0.00588399");
 541
 542static IIO_DEV_ATTR_INCLI_X(adis16300_read_13bit_signed,
 543                ADIS16300_XINCLI_OUT);
 544static IIO_DEV_ATTR_INCLI_Y(adis16300_read_13bit_signed,
 545                ADIS16300_YINCLI_OUT);
 546static IIO_CONST_ATTR_INCLI_SCALE("0.00076794487");
 547
 548static IIO_DEV_ATTR_TEMP_RAW(adis16300_read_12bit_unsigned);
 549static IIO_CONST_ATTR_TEMP_OFFSET("198.16");
 550static IIO_CONST_ATTR_TEMP_SCALE("0.14");
 551
 552static IIO_DEV_ATTR_IN_RAW(1, adis16300_read_12bit_unsigned,
 553                ADIS16300_AUX_ADC);
 554static IIO_CONST_ATTR(in1_scale, "0.000806");
 555
 556static IIO_DEV_ATTR_SAMP_FREQ(S_IWUSR | S_IRUGO,
 557                adis16300_read_frequency,
 558                adis16300_write_frequency);
 559
 560static IIO_DEVICE_ATTR(reset, S_IWUSR, NULL, adis16300_write_reset, 0);
 561
 562static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("409 546 819 1638");
 563
 564static IIO_CONST_ATTR_NAME("adis16300");
 565
 566static struct attribute *adis16300_event_attributes[] = {
 567        NULL
 568};
 569
 570static struct attribute_group adis16300_event_attribute_group = {
 571        .attrs = adis16300_event_attributes,
 572};
 573
 574static struct attribute *adis16300_attributes[] = {
 575        &iio_dev_attr_gyro_x_calibbias.dev_attr.attr,
 576        &iio_dev_attr_accel_x_calibbias.dev_attr.attr,
 577        &iio_dev_attr_accel_y_calibbias.dev_attr.attr,
 578        &iio_dev_attr_accel_z_calibbias.dev_attr.attr,
 579        &iio_dev_attr_in0_supply_raw.dev_attr.attr,
 580        &iio_const_attr_in0_supply_scale.dev_attr.attr,
 581        &iio_dev_attr_gyro_x_raw.dev_attr.attr,
 582        &iio_const_attr_gyro_scale.dev_attr.attr,
 583        &iio_dev_attr_accel_x_raw.dev_attr.attr,
 584        &iio_dev_attr_accel_y_raw.dev_attr.attr,
 585        &iio_dev_attr_accel_z_raw.dev_attr.attr,
 586        &iio_const_attr_accel_scale.dev_attr.attr,
 587        &iio_dev_attr_incli_x_raw.dev_attr.attr,
 588        &iio_dev_attr_incli_y_raw.dev_attr.attr,
 589        &iio_const_attr_incli_scale.dev_attr.attr,
 590        &iio_dev_attr_temp_raw.dev_attr.attr,
 591        &iio_const_attr_temp_offset.dev_attr.attr,
 592        &iio_const_attr_temp_scale.dev_attr.attr,
 593        &iio_dev_attr_in1_raw.dev_attr.attr,
 594        &iio_const_attr_in1_scale.dev_attr.attr,
 595        &iio_dev_attr_sampling_frequency.dev_attr.attr,
 596        &iio_const_attr_sampling_frequency_available.dev_attr.attr,
 597        &iio_dev_attr_reset.dev_attr.attr,
 598        &iio_const_attr_name.dev_attr.attr,
 599        NULL
 600};
 601
 602static const struct attribute_group adis16300_attribute_group = {
 603        .attrs = adis16300_attributes,
 604};
 605
 606static int __devinit adis16300_probe(struct spi_device *spi)
 607{
 608        int ret, regdone = 0;
 609        struct adis16300_state *st = kzalloc(sizeof *st, GFP_KERNEL);
 610        if (!st) {
 611                ret =  -ENOMEM;
 612                goto error_ret;
 613        }
 614        /* this is only used for removal purposes */
 615        spi_set_drvdata(spi, st);
 616
 617        /* Allocate the comms buffers */
 618        st->rx = kzalloc(sizeof(*st->rx)*ADIS16300_MAX_RX, GFP_KERNEL);
 619        if (st->rx == NULL) {
 620                ret = -ENOMEM;
 621                goto error_free_st;
 622        }
 623        st->tx = kzalloc(sizeof(*st->tx)*ADIS16300_MAX_TX, GFP_KERNEL);
 624        if (st->tx == NULL) {
 625                ret = -ENOMEM;
 626                goto error_free_rx;
 627        }
 628        st->us = spi;
 629        mutex_init(&st->buf_lock);
 630        /* setup the industrialio driver allocated elements */
 631        st->indio_dev = iio_allocate_device();
 632        if (st->indio_dev == NULL) {
 633                ret = -ENOMEM;
 634                goto error_free_tx;
 635        }
 636
 637        st->indio_dev->dev.parent = &spi->dev;
 638        st->indio_dev->num_interrupt_lines = 1;
 639        st->indio_dev->event_attrs = &adis16300_event_attribute_group;
 640        st->indio_dev->attrs = &adis16300_attribute_group;
 641        st->indio_dev->dev_data = (void *)(st);
 642        st->indio_dev->driver_module = THIS_MODULE;
 643        st->indio_dev->modes = INDIO_DIRECT_MODE;
 644
 645        ret = adis16300_configure_ring(st->indio_dev);
 646        if (ret)
 647                goto error_free_dev;
 648
 649        ret = iio_device_register(st->indio_dev);
 650        if (ret)
 651                goto error_unreg_ring_funcs;
 652        regdone = 1;
 653
 654        ret = iio_ring_buffer_register(st->indio_dev->ring, 0);
 655        if (ret) {
 656                printk(KERN_ERR "failed to initialize the ring\n");
 657                goto error_unreg_ring_funcs;
 658        }
 659
 660        if (spi->irq) {
 661                ret = iio_register_interrupt_line(spi->irq,
 662                                st->indio_dev,
 663                                0,
 664                                IRQF_TRIGGER_RISING,
 665                                "adis16300");
 666                if (ret)
 667                        goto error_uninitialize_ring;
 668
 669                ret = adis16300_probe_trigger(st->indio_dev);
 670                if (ret)
 671                        goto error_unregister_line;
 672        }
 673
 674        /* Get the device into a sane initial state */
 675        ret = adis16300_initial_setup(st);
 676        if (ret)
 677                goto error_remove_trigger;
 678        return 0;
 679
 680error_remove_trigger:
 681        adis16300_remove_trigger(st->indio_dev);
 682error_unregister_line:
 683        if (spi->irq)
 684                iio_unregister_interrupt_line(st->indio_dev, 0);
 685error_uninitialize_ring:
 686        iio_ring_buffer_unregister(st->indio_dev->ring);
 687error_unreg_ring_funcs:
 688        adis16300_unconfigure_ring(st->indio_dev);
 689error_free_dev:
 690        if (regdone)
 691                iio_device_unregister(st->indio_dev);
 692        else
 693                iio_free_device(st->indio_dev);
 694error_free_tx:
 695        kfree(st->tx);
 696error_free_rx:
 697        kfree(st->rx);
 698error_free_st:
 699        kfree(st);
 700error_ret:
 701        return ret;
 702}
 703
 704static int adis16300_remove(struct spi_device *spi)
 705{
 706        int ret;
 707        struct adis16300_state *st = spi_get_drvdata(spi);
 708        struct iio_dev *indio_dev = st->indio_dev;
 709
 710        ret = adis16300_stop_device(&(indio_dev->dev));
 711        if (ret)
 712                goto err_ret;
 713
 714        flush_scheduled_work();
 715
 716        adis16300_remove_trigger(indio_dev);
 717        if (spi->irq)
 718                iio_unregister_interrupt_line(indio_dev, 0);
 719
 720        iio_ring_buffer_unregister(indio_dev->ring);
 721        iio_device_unregister(indio_dev);
 722        adis16300_unconfigure_ring(indio_dev);
 723        kfree(st->tx);
 724        kfree(st->rx);
 725        kfree(st);
 726
 727        return 0;
 728
 729err_ret:
 730        return ret;
 731}
 732
 733static struct spi_driver adis16300_driver = {
 734        .driver = {
 735                .name = "adis16300",
 736                .owner = THIS_MODULE,
 737        },
 738        .probe = adis16300_probe,
 739        .remove = __devexit_p(adis16300_remove),
 740};
 741
 742static __init int adis16300_init(void)
 743{
 744        return spi_register_driver(&adis16300_driver);
 745}
 746module_init(adis16300_init);
 747
 748static __exit void adis16300_exit(void)
 749{
 750        spi_unregister_driver(&adis16300_driver);
 751}
 752module_exit(adis16300_exit);
 753
 754MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>");
 755MODULE_DESCRIPTION("Analog Devices ADIS16300 IMU SPI driver");
 756MODULE_LICENSE("GPL v2");
 757