/**
 * ds2482.c - provides i2c to w1-master bridge(s)
 * Copyright (C) 2005  Ben Gardner <bgardner@wabtec.com>
 *
 * The DS2482 is a sensor chip made by Dallas Semiconductor (Maxim).
 * It is a I2C to 1-wire bridge.
 * There are two variations: -100 and -800, which have 1 or 8 1-wire ports.
 * The complete datasheet can be obtained from MAXIM's website at:
 *   http://www.maxim-ic.com/quick_view2.cfm/qv_pk/4382
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/delay.h>
#include <asm/delay.h>

#include "../w1.h"
#include "../w1_int.h"

/**
 * The DS2482 registers - there are 3 registers that are addressed by a read
 * pointer. The read pointer is set by the last command executed.
 *
 * To read the data, issue a register read for any address
 */
#define DS2482_CMD_RESET                0xF0    /* No param */
#define DS2482_CMD_SET_READ_PTR         0xE1    /* Param: DS2482_PTR_CODE_xxx */
#define DS2482_CMD_CHANNEL_SELECT       0xC3    /* Param: Channel byte - DS2482-800 only */
#define DS2482_CMD_WRITE_CONFIG         0xD2    /* Param: Config byte */
#define DS2482_CMD_1WIRE_RESET          0xB4    /* Param: None */
#define DS2482_CMD_1WIRE_SINGLE_BIT     0x87    /* Param: Bit byte (bit7) */
#define DS2482_CMD_1WIRE_WRITE_BYTE     0xA5    /* Param: Data byte */
#define DS2482_CMD_1WIRE_READ_BYTE      0x96    /* Param: None */
/* Note to read the byte, Set the ReadPtr to Data then read (any addr) */
#define DS2482_CMD_1WIRE_TRIPLET        0x78    /* Param: Dir byte (bit7) */

/* Values for DS2482_CMD_SET_READ_PTR */
#define DS2482_PTR_CODE_STATUS          0xF0
#define DS2482_PTR_CODE_DATA            0xE1
#define DS2482_PTR_CODE_CHANNEL         0xD2    /* DS2482-800 only */
#define DS2482_PTR_CODE_CONFIG          0xC3

/**
 * Configure Register bit definitions
 * The top 4 bits always read 0.
 * To write, the top nibble must be the 1's compl. of the low nibble.
 */
#define DS2482_REG_CFG_1WS              0x08
#define DS2482_REG_CFG_SPU              0x04
#define DS2482_REG_CFG_PPM              0x02
#define DS2482_REG_CFG_APU              0x01


/**
 * Write and verify codes for the CHANNEL_SELECT command (DS2482-800 only).
 * To set the channel, write the value at the index of the channel.
 * Read and compare against the corresponding value to verify the change.
 */
static const u8 ds2482_chan_wr[8] =
        { 0xF0, 0xE1, 0xD2, 0xC3, 0xB4, 0xA5, 0x96, 0x87 };
static const u8 ds2482_chan_rd[8] =
        { 0xB8, 0xB1, 0xAA, 0xA3, 0x9C, 0x95, 0x8E, 0x87 };


/**
 * Status Register bit definitions (read only)
 */
#define DS2482_REG_STS_DIR              0x80
#define DS2482_REG_STS_TSB              0x40
#define DS2482_REG_STS_SBR              0x20
#define DS2482_REG_STS_RST              0x10
#define DS2482_REG_STS_LL               0x08
#define DS2482_REG_STS_SD               0x04
#define DS2482_REG_STS_PPD              0x02
#define DS2482_REG_STS_1WB              0x01


static int ds2482_probe(struct i2c_client *client,
                        const struct i2c_device_id *id);
static int ds2482_remove(struct i2c_client *client);


/**
 * Driver data (common to all clients)
 */
static const struct i2c_device_id ds2482_id[] = {
        { "ds2482", 0 },
        { }
};

static struct i2c_driver ds2482_driver = {
        .driver = {
                .owner  = THIS_MODULE,
                .name   = "ds2482",
        },
        .probe          = ds2482_probe,
        .remove         = ds2482_remove,
        .id_table       = ds2482_id,
};

/*
 * Client data (each client gets its own)
 */

struct ds2482_data;

struct ds2482_w1_chan {
        struct ds2482_data      *pdev;
        u8                      channel;
        struct w1_bus_master    w1_bm;
};

struct ds2482_data {
        struct i2c_client       *client;
        struct mutex            access_lock;

        /* 1-wire interface(s) */
        int                     w1_count;       /* 1 or 8 */
        struct ds2482_w1_chan   w1_ch[8];

        /* per-device values */
        u8                      channel;
        u8                      read_prt;       /* see DS2482_PTR_CODE_xxx */
        u8                      reg_config;
};


/**
 * Sets the read pointer.
 * @param pdev          The ds2482 client pointer
 * @param read_ptr      see DS2482_PTR_CODE_xxx above
 * @return -1 on failure, 0 on success
 */
static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr)
{
        if (pdev->read_prt != read_ptr) {
                if (i2c_smbus_write_byte_data(pdev->client,
                                              DS2482_CMD_SET_READ_PTR,
                                              read_ptr) < 0)
                        return -1;

                pdev->read_prt = read_ptr;
        }
        return 0;
}

/**
 * Sends a command without a parameter
 * @param pdev  The ds2482 client pointer
 * @param cmd   DS2482_CMD_RESET,
 *              DS2482_CMD_1WIRE_RESET,
 *              DS2482_CMD_1WIRE_READ_BYTE
 * @return -1 on failure, 0 on success
 */
static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd)
{
        if (i2c_smbus_write_byte(pdev->client, cmd) < 0)
                return -1;

        pdev->read_prt = DS2482_PTR_CODE_STATUS;
        return 0;
}

/**
 * Sends a command with a parameter
 * @param pdev  The ds2482 client pointer
 * @param cmd   DS2482_CMD_WRITE_CONFIG,
 *              DS2482_CMD_1WIRE_SINGLE_BIT,
 *              DS2482_CMD_1WIRE_WRITE_BYTE,
 *              DS2482_CMD_1WIRE_TRIPLET
 * @param byte  The data to send
 * @return -1 on failure, 0 on success
 */
static inline int ds2482_send_cmd_data(struct ds2482_data *pdev,
                                       u8 cmd, u8 byte)
{
        if (i2c_smbus_write_byte_data(pdev->client, cmd, byte) < 0)
                return -1;

        /* all cmds leave in STATUS, except CONFIG */
        pdev->read_prt = (cmd != DS2482_CMD_WRITE_CONFIG) ?
                         DS2482_PTR_CODE_STATUS : DS2482_PTR_CODE_CONFIG;
        return 0;
}


/*
 * 1-Wire interface code
 */

#define DS2482_WAIT_IDLE_TIMEOUT        100

/**
 * Waits until the 1-wire interface is idle (not busy)
 *
 * @param pdev Pointer to the device structure
 * @return the last value read from status or -1 (failure)
 */
static int ds2482_wait_1wire_idle(struct ds2482_data *pdev)
{
        int temp = -1;
        int retries = 0;

        if (!ds2482_select_register(pdev, DS2482_PTR_CODE_STATUS)) {
                do {
                        temp = i2c_smbus_read_byte(pdev->client);
                } while ((temp >= 0) && (temp & DS2482_REG_STS_1WB) &&
                         (++retries < DS2482_WAIT_IDLE_TIMEOUT));
        }

        if (retries >= DS2482_WAIT_IDLE_TIMEOUT)
                printk(KERN_ERR "%s: timeout on channel %d\n",
                       __func__, pdev->channel);

        return temp;
}

/**
 * Selects a w1 channel.
 * The 1-wire interface must be idle before calling this function.
 *
 * @param pdev          The ds2482 client pointer
 * @param channel       0-7
 * @return              -1 (failure) or 0 (success)
 */
static int ds2482_set_channel(struct ds2482_data *pdev, u8 channel)
{
        if (i2c_smbus_write_byte_data(pdev->client, DS2482_CMD_CHANNEL_SELECT,
                                      ds2482_chan_wr[channel]) < 0)
                return -1;

        pdev->read_prt = DS2482_PTR_CODE_CHANNEL;
        pdev->channel = -1;
        if (i2c_smbus_read_byte(pdev->client) == ds2482_chan_rd[channel]) {
                pdev->channel = channel;
                return 0;
        }
        return -1;
}


/**
 * Performs the touch-bit function, which writes a 0 or 1 and reads the level.
 *
 * @param data  The ds2482 channel pointer
 * @param bit   The level to write: 0 or non-zero
 * @return      The level read: 0 or 1
 */
static u8 ds2482_w1_touch_bit(void *data, u8 bit)
{
        struct ds2482_w1_chan *pchan = data;
        struct ds2482_data    *pdev = pchan->pdev;
        int status = -1;

        mutex_lock(&pdev->access_lock);

        /* Select the channel */
        ds2482_wait_1wire_idle(pdev);
        if (pdev->w1_count > 1)
                ds2482_set_channel(pdev, pchan->channel);

        /* Send the touch command, wait until 1WB == 0, return the status */
        if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_SINGLE_BIT,
                                  bit ? 0xFF : 0))
                status = ds2482_wait_1wire_idle(pdev);

        mutex_unlock(&pdev->access_lock);

        return (status & DS2482_REG_STS_SBR) ? 1 : 0;
}

/**
 * Performs the triplet function, which reads two bits and writes a bit.
 * The bit written is determined by the two reads:
 *   00 => dbit, 01 => 0, 10 => 1
 *
 * @param data  The ds2482 channel pointer
 * @param dbit  The direction to choose if both branches are valid
 * @return      b0=read1 b1=read2 b3=bit written
 */
static u8 ds2482_w1_triplet(void *data, u8 dbit)
{
        struct ds2482_w1_chan *pchan = data;
        struct ds2482_data    *pdev = pchan->pdev;
        int status = (3 << 5);

        mutex_lock(&pdev->access_lock);

        /* Select the channel */
        ds2482_wait_1wire_idle(pdev);
        if (pdev->w1_count > 1)
                ds2482_set_channel(pdev, pchan->channel);

        /* Send the triplet command, wait until 1WB == 0, return the status */
        if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_TRIPLET,
                                  dbit ? 0xFF : 0))
                status = ds2482_wait_1wire_idle(pdev);

        mutex_unlock(&pdev->access_lock);

        /* Decode the status */
        return (status >> 5);
}

/**
 * Performs the write byte function.
 *
 * @param data  The ds2482 channel pointer
 * @param byte  The value to write
 */
static void ds2482_w1_write_byte(void *data, u8 byte)
{
        struct ds2482_w1_chan *pchan = data;
        struct ds2482_data    *pdev = pchan->pdev;

        mutex_lock(&pdev->access_lock);

        /* Select the channel */
        ds2482_wait_1wire_idle(pdev);
        if (pdev->w1_count > 1)
                ds2482_set_channel(pdev, pchan->channel);

        /* Send the write byte command */
        ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_WRITE_BYTE, byte);

        mutex_unlock(&pdev->access_lock);
}

/**
 * Performs the read byte function.
 *
 * @param data  The ds2482 channel pointer
 * @return      The value read
 */
static u8 ds2482_w1_read_byte(void *data)
{
        struct ds2482_w1_chan *pchan = data;
        struct ds2482_data    *pdev = pchan->pdev;
        int result;

        mutex_lock(&pdev->access_lock);

        /* Select the channel */
        ds2482_wait_1wire_idle(pdev);
        if (pdev->w1_count > 1)
                ds2482_set_channel(pdev, pchan->channel);

        /* Send the read byte command */
        ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_READ_BYTE);

        /* Wait until 1WB == 0 */
        ds2482_wait_1wire_idle(pdev);

        /* Select the data register */
        ds2482_select_register(pdev, DS2482_PTR_CODE_DATA);

        /* Read the data byte */
        result = i2c_smbus_read_byte(pdev->client);

        mutex_unlock(&pdev->access_lock);

        return result;
}


/**
 * Sends a reset on the 1-wire interface
 *
 * @param data  The ds2482 channel pointer
 * @return      0=Device present, 1=No device present or error
 */
static u8 ds2482_w1_reset_bus(void *data)
{
        struct ds2482_w1_chan *pchan = data;
        struct ds2482_data    *pdev = pchan->pdev;
        int err;
        u8 retval = 1;

        mutex_lock(&pdev->access_lock);

        /* Select the channel */
        ds2482_wait_1wire_idle(pdev);
        if (pdev->w1_count > 1)
                ds2482_set_channel(pdev, pchan->channel);

        /* Send the reset command */
        err = ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_RESET);
        if (err >= 0) {
                /* Wait until the reset is complete */
                err = ds2482_wait_1wire_idle(pdev);
                retval = !(err & DS2482_REG_STS_PPD);

                /* If the chip did reset since detect, re-config it */
                if (err & DS2482_REG_STS_RST)
                        ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG,
                                             0xF0);
        }

        mutex_unlock(&pdev->access_lock);

        return retval;
}


static int ds2482_probe(struct i2c_client *client,
                        const struct i2c_device_id *id)
{
        struct ds2482_data *data;
        int err = -ENODEV;
        int temp1;
        int idx;

        if (!i2c_check_functionality(client->adapter,
                                     I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
                                     I2C_FUNC_SMBUS_BYTE))
                return -ENODEV;

        if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) {
                err = -ENOMEM;
                goto exit;
        }

        data->client = client;
        i2c_set_clientdata(client, data);

        /* Reset the device (sets the read_ptr to status) */
        if (ds2482_send_cmd(data, DS2482_CMD_RESET) < 0) {
                dev_warn(&client->dev, "DS2482 reset failed.\n");
                goto exit_free;
        }

        /* Sleep at least 525ns to allow the reset to complete */
        ndelay(525);

        /* Read the status byte - only reset bit and line should be set */
        temp1 = i2c_smbus_read_byte(client);
        if (temp1 != (DS2482_REG_STS_LL | DS2482_REG_STS_RST)) {
                dev_warn(&client->dev, "DS2482 reset status "
                         "0x%02X - not a DS2482\n", temp1);
                goto exit_free;
        }

        /* Detect the 8-port version */
        data->w1_count = 1;
        if (ds2482_set_channel(data, 7) == 0)
                data->w1_count = 8;

        /* Set all config items to 0 (off) */
        ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, 0xF0);

        mutex_init(&data->access_lock);

        /* Register 1-wire interface(s) */
        for (idx = 0; idx < data->w1_count; idx++) {
                data->w1_ch[idx].pdev = data;
                data->w1_ch[idx].channel = idx;

                /* Populate all the w1 bus master stuff */
                data->w1_ch[idx].w1_bm.data       = &data->w1_ch[idx];
                data->w1_ch[idx].w1_bm.read_byte  = ds2482_w1_read_byte;
                data->w1_ch[idx].w1_bm.write_byte = ds2482_w1_write_byte;
                data->w1_ch[idx].w1_bm.touch_bit  = ds2482_w1_touch_bit;
                data->w1_ch[idx].w1_bm.triplet    = ds2482_w1_triplet;
                data->w1_ch[idx].w1_bm.reset_bus  = ds2482_w1_reset_bus;

                err = w1_add_master_device(&data->w1_ch[idx].w1_bm);
                if (err) {
                        data->w1_ch[idx].pdev = NULL;
                        goto exit_w1_remove;
                }
        }

        return 0;

exit_w1_remove:
        for (idx = 0; idx < data->w1_count; idx++) {
                if (data->w1_ch[idx].pdev != NULL)
                        w1_remove_master_device(&data->w1_ch[idx].w1_bm);
        }
exit_free:
        kfree(data);
exit:
        return err;
}

static int ds2482_remove(struct i2c_client *client)
{
        struct ds2482_data   *data = i2c_get_clientdata(client);
        int idx;

        /* Unregister the 1-wire bridge(s) */
        for (idx = 0; idx < data->w1_count; idx++) {
                if (data->w1_ch[idx].pdev != NULL)
                        w1_remove_master_device(&data->w1_ch[idx].w1_bm);
        }

        /* Free the memory */
        kfree(data);
        return 0;
}

static int __init sensors_ds2482_init(void)
{
        return i2c_add_driver(&ds2482_driver);
}

static void __exit sensors_ds2482_exit(void)
{
        i2c_del_driver(&ds2482_driver);
}

MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
MODULE_DESCRIPTION("DS2482 driver");
MODULE_LICENSE("GPL");

module_init(sensors_ds2482_init);
module_exit(sensors_ds2482_exit);