1#ifndef _PARISC_SUPERIO_H 2#define _PARISC_SUPERIO_H 3 4#define IC_PIC1 0x20 /* PCI I/O address of master 8259 */ 5#define IC_PIC2 0xA0 /* PCI I/O address of slave */ 6 7/* Config Space Offsets to configuration and base address registers */ 8#define SIO_CR 0x5A /* Configuration Register */ 9#define SIO_ACPIBAR 0x88 /* ACPI BAR */ 10#define SIO_FDCBAR 0x90 /* Floppy Disk Controller BAR */ 11#define SIO_SP1BAR 0x94 /* Serial 1 BAR */ 12#define SIO_SP2BAR 0x98 /* Serial 2 BAR */ 13#define SIO_PPBAR 0x9C /* Parallel BAR */ 14 15#define TRIGGER_1 0x67 /* Edge/level trigger register 1 */ 16#define TRIGGER_2 0x68 /* Edge/level trigger register 2 */ 17 18/* Interrupt Routing Control registers */ 19#define CFG_IR_SER 0x69 /* Serial 1 [0:3] and Serial 2 [4:7] */ 20#define CFG_IR_PFD 0x6a /* Parallel [0:3] and Floppy [4:7] */ 21#define CFG_IR_IDE 0x6b /* IDE1 [0:3] and IDE2 [4:7] */ 22#define CFG_IR_INTAB 0x6c /* PCI INTA [0:3] and INT B [4:7] */ 23#define CFG_IR_INTCD 0x6d /* PCI INTC [0:3] and INT D [4:7] */ 24#define CFG_IR_PS2 0x6e /* PS/2 KBINT [0:3] and Mouse [4:7] */ 25#define CFG_IR_FXBUS 0x6f /* FXIRQ[0] [0:3] and FXIRQ[1] [4:7] */ 26#define CFG_IR_USB 0x70 /* FXIRQ[2] [0:3] and USB [4:7] */ 27#define CFG_IR_ACPI 0x71 /* ACPI SCI [0:3] and reserved [4:7] */ 28 29#define CFG_IR_LOW CFG_IR_SER /* Lowest interrupt routing reg */ 30#define CFG_IR_HIGH CFG_IR_ACPI /* Highest interrupt routing reg */ 31 32/* 8259 operational control words */ 33#define OCW2_EOI 0x20 /* Non-specific EOI */ 34#define OCW2_SEOI 0x60 /* Specific EOI */ 35#define OCW3_IIR 0x0A /* Read request register */ 36#define OCW3_ISR 0x0B /* Read service register */ 37#define OCW3_POLL 0x0C /* Poll the PIC for an interrupt vector */ 38 39/* Interrupt lines. Only PIC1 is used */ 40#define USB_IRQ 1 /* USB */ 41#define SP1_IRQ 3 /* Serial port 1 */ 42#define SP2_IRQ 4 /* Serial port 2 */ 43#define PAR_IRQ 5 /* Parallel port */ 44#define FDC_IRQ 6 /* Floppy controller */ 45#define IDE_IRQ 7 /* IDE (pri+sec) */ 46 47/* ACPI registers */ 48#define USB_REG_CR 0x1f /* USB Regulator Control Register */ 49 50#define SUPERIO_NIRQS 8 51 52struct superio_device { 53 u32 fdc_base; 54 u32 sp1_base; 55 u32 sp2_base; 56 u32 pp_base; 57 u32 acpi_base; 58 int suckyio_irq_enabled; 59 struct pci_dev *lio_pdev; /* pci device for legacy IO (fn 1) */ 60 struct pci_dev *usb_pdev; /* pci device for USB (fn 2) */ 61}; 62 63/* 64 * Does NS make a 87415 based plug in PCI card? If so, because of this 65 * macro we currently don't support it being plugged into a machine 66 * that contains a SuperIO chip AND has CONFIG_SUPERIO enabled. 67 * 68 * This could be fixed by checking to see if function 1 exists, and 69 * if it is SuperIO Legacy IO; but really now, is this combination 70 * going to EVER happen? 71 */ 72 73#define SUPERIO_IDE_FN 0 /* Function number of IDE controller */ 74#define SUPERIO_LIO_FN 1 /* Function number of Legacy IO controller */ 75#define SUPERIO_USB_FN 2 /* Function number of USB controller */ 76 77#define is_superio_device(x) \ 78 (((x)->vendor == PCI_VENDOR_ID_NS) && \ 79 ( ((x)->device == PCI_DEVICE_ID_NS_87415) \ 80 || ((x)->device == PCI_DEVICE_ID_NS_87560_LIO) \ 81 || ((x)->device == PCI_DEVICE_ID_NS_87560_USB) ) ) 82 83extern int superio_fixup_irq(struct pci_dev *pcidev); /* called by iosapic */ 84 85#endif /* _PARISC_SUPERIO_H */ 86