linux/drivers/hwmon/jc42.c
<<
>>
Prefs
   1/*
   2 * jc42.c - driver for Jedec JC42.4 compliant temperature sensors
   3 *
   4 * Copyright (c) 2010  Ericsson AB.
   5 *
   6 * Derived from lm77.c by Andras BALI <drewie@freemail.hu>.
   7 *
   8 * JC42.4 compliant temperature sensors are typically used on memory modules.
   9 *
  10 * This program is free software; you can redistribute it and/or modify
  11 * it under the terms of the GNU General Public License as published by
  12 * the Free Software Foundation; either version 2 of the License, or
  13 * (at your option) any later version.
  14 *
  15 * This program is distributed in the hope that it will be useful,
  16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
  17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  18 * GNU General Public License for more details.
  19 *
  20 * You should have received a copy of the GNU General Public License
  21 * along with this program; if not, write to the Free Software
  22 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  23 */
  24
  25#include <linux/module.h>
  26#include <linux/init.h>
  27#include <linux/slab.h>
  28#include <linux/jiffies.h>
  29#include <linux/i2c.h>
  30#include <linux/hwmon.h>
  31#include <linux/hwmon-sysfs.h>
  32#include <linux/err.h>
  33#include <linux/mutex.h>
  34
  35/* Addresses to scan */
  36static const unsigned short normal_i2c[] = {
  37        0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, I2C_CLIENT_END };
  38
  39/* JC42 registers. All registers are 16 bit. */
  40#define JC42_REG_CAP            0x00
  41#define JC42_REG_CONFIG         0x01
  42#define JC42_REG_TEMP_UPPER     0x02
  43#define JC42_REG_TEMP_LOWER     0x03
  44#define JC42_REG_TEMP_CRITICAL  0x04
  45#define JC42_REG_TEMP           0x05
  46#define JC42_REG_MANID          0x06
  47#define JC42_REG_DEVICEID       0x07
  48
  49/* Status bits in temperature register */
  50#define JC42_ALARM_CRIT_BIT     15
  51#define JC42_ALARM_MAX_BIT      14
  52#define JC42_ALARM_MIN_BIT      13
  53
  54/* Configuration register defines */
  55#define JC42_CFG_CRIT_ONLY      (1 << 2)
  56#define JC42_CFG_TCRIT_LOCK     (1 << 6)
  57#define JC42_CFG_EVENT_LOCK     (1 << 7)
  58#define JC42_CFG_SHUTDOWN       (1 << 8)
  59#define JC42_CFG_HYST_SHIFT     9
  60#define JC42_CFG_HYST_MASK      0x03
  61
  62/* Capabilities */
  63#define JC42_CAP_RANGE          (1 << 2)
  64
  65/* Manufacturer IDs */
  66#define ADT_MANID               0x11d4  /* Analog Devices */
  67#define MAX_MANID               0x004d  /* Maxim */
  68#define IDT_MANID               0x00b3  /* IDT */
  69#define MCP_MANID               0x0054  /* Microchip */
  70#define NXP_MANID               0x1131  /* NXP Semiconductors */
  71#define ONS_MANID               0x1b09  /* ON Semiconductor */
  72#define STM_MANID               0x104a  /* ST Microelectronics */
  73
  74/* Supported chips */
  75
  76/* Analog Devices */
  77#define ADT7408_DEVID           0x0801
  78#define ADT7408_DEVID_MASK      0xffff
  79
  80/* IDT */
  81#define TS3000B3_DEVID          0x2903  /* Also matches TSE2002B3 */
  82#define TS3000B3_DEVID_MASK     0xffff
  83
  84/* Maxim */
  85#define MAX6604_DEVID           0x3e00
  86#define MAX6604_DEVID_MASK      0xffff
  87
  88/* Microchip */
  89#define MCP98242_DEVID          0x2000
  90#define MCP98242_DEVID_MASK     0xfffc
  91
  92#define MCP98243_DEVID          0x2100
  93#define MCP98243_DEVID_MASK     0xfffc
  94
  95#define MCP9843_DEVID           0x0000  /* Also matches mcp9805 */
  96#define MCP9843_DEVID_MASK      0xfffe
  97
  98/* NXP */
  99#define SE97_DEVID              0xa200
 100#define SE97_DEVID_MASK         0xfffc
 101
 102#define SE98_DEVID              0xa100
 103#define SE98_DEVID_MASK         0xfffc
 104
 105/* ON Semiconductor */
 106#define CAT6095_DEVID           0x0800  /* Also matches CAT34TS02 */
 107#define CAT6095_DEVID_MASK      0xffe0
 108
 109/* ST Microelectronics */
 110#define STTS424_DEVID           0x0101
 111#define STTS424_DEVID_MASK      0xffff
 112
 113#define STTS424E_DEVID          0x0000
 114#define STTS424E_DEVID_MASK     0xfffe
 115
 116static u16 jc42_hysteresis[] = { 0, 1500, 3000, 6000 };
 117
 118struct jc42_chips {
 119        u16 manid;
 120        u16 devid;
 121        u16 devid_mask;
 122};
 123
 124static struct jc42_chips jc42_chips[] = {
 125        { ADT_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK },
 126        { IDT_MANID, TS3000B3_DEVID, TS3000B3_DEVID_MASK },
 127        { MAX_MANID, MAX6604_DEVID, MAX6604_DEVID_MASK },
 128        { MCP_MANID, MCP98242_DEVID, MCP98242_DEVID_MASK },
 129        { MCP_MANID, MCP98243_DEVID, MCP98243_DEVID_MASK },
 130        { MCP_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK },
 131        { NXP_MANID, SE97_DEVID, SE97_DEVID_MASK },
 132        { ONS_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK },
 133        { NXP_MANID, SE98_DEVID, SE98_DEVID_MASK },
 134        { STM_MANID, STTS424_DEVID, STTS424_DEVID_MASK },
 135        { STM_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK },
 136};
 137
 138/* Each client has this additional data */
 139struct jc42_data {
 140        struct device   *hwmon_dev;
 141        struct mutex    update_lock;    /* protect register access */
 142        bool            extended;       /* true if extended range supported */
 143        bool            valid;
 144        unsigned long   last_updated;   /* In jiffies */
 145        u16             orig_config;    /* original configuration */
 146        u16             config;         /* current configuration */
 147        u16             temp_input;     /* Temperatures */
 148        u16             temp_crit;
 149        u16             temp_min;
 150        u16             temp_max;
 151};
 152
 153static int jc42_probe(struct i2c_client *client,
 154                      const struct i2c_device_id *id);
 155static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info);
 156static int jc42_remove(struct i2c_client *client);
 157static int jc42_read_value(struct i2c_client *client, u8 reg);
 158static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value);
 159
 160static struct jc42_data *jc42_update_device(struct device *dev);
 161
 162static const struct i2c_device_id jc42_id[] = {
 163        { "adt7408", 0 },
 164        { "cat94ts02", 0 },
 165        { "cat6095", 0 },
 166        { "jc42", 0 },
 167        { "max6604", 0 },
 168        { "mcp9805", 0 },
 169        { "mcp98242", 0 },
 170        { "mcp98243", 0 },
 171        { "mcp9843", 0 },
 172        { "se97", 0 },
 173        { "se97b", 0 },
 174        { "se98", 0 },
 175        { "stts424", 0 },
 176        { "tse2002b3", 0 },
 177        { "ts3000b3", 0 },
 178        { }
 179};
 180MODULE_DEVICE_TABLE(i2c, jc42_id);
 181
 182#ifdef CONFIG_PM
 183
 184static int jc42_suspend(struct device *dev)
 185{
 186        struct i2c_client *client = to_i2c_client(dev);
 187        struct jc42_data *data = i2c_get_clientdata(client);
 188
 189        data->config |= JC42_CFG_SHUTDOWN;
 190        jc42_write_value(client, JC42_REG_CONFIG, data->config);
 191        return 0;
 192}
 193
 194static int jc42_resume(struct device *dev)
 195{
 196        struct i2c_client *client = to_i2c_client(dev);
 197        struct jc42_data *data = i2c_get_clientdata(client);
 198
 199        data->config &= ~JC42_CFG_SHUTDOWN;
 200        jc42_write_value(client, JC42_REG_CONFIG, data->config);
 201        return 0;
 202}
 203
 204static const struct dev_pm_ops jc42_dev_pm_ops = {
 205        .suspend = jc42_suspend,
 206        .resume = jc42_resume,
 207};
 208
 209#define JC42_DEV_PM_OPS (&jc42_dev_pm_ops)
 210#else
 211#define JC42_DEV_PM_OPS NULL
 212#endif /* CONFIG_PM */
 213
 214/* This is the driver that will be inserted */
 215static struct i2c_driver jc42_driver = {
 216        .class          = I2C_CLASS_SPD,
 217        .driver = {
 218                .name   = "jc42",
 219                .pm = JC42_DEV_PM_OPS,
 220        },
 221        .probe          = jc42_probe,
 222        .remove         = jc42_remove,
 223        .id_table       = jc42_id,
 224        .detect         = jc42_detect,
 225        .address_list   = normal_i2c,
 226};
 227
 228#define JC42_TEMP_MIN_EXTENDED  (-40000)
 229#define JC42_TEMP_MIN           0
 230#define JC42_TEMP_MAX           125000
 231
 232static u16 jc42_temp_to_reg(int temp, bool extended)
 233{
 234        int ntemp = SENSORS_LIMIT(temp,
 235                                  extended ? JC42_TEMP_MIN_EXTENDED :
 236                                  JC42_TEMP_MIN, JC42_TEMP_MAX);
 237
 238        /* convert from 0.001 to 0.0625 resolution */
 239        return (ntemp * 2 / 125) & 0x1fff;
 240}
 241
 242static int jc42_temp_from_reg(s16 reg)
 243{
 244        reg &= 0x1fff;
 245
 246        /* sign extend register */
 247        if (reg & 0x1000)
 248                reg |= 0xf000;
 249
 250        /* convert from 0.0625 to 0.001 resolution */
 251        return reg * 125 / 2;
 252}
 253
 254/* sysfs stuff */
 255
 256/* read routines for temperature limits */
 257#define show(value)     \
 258static ssize_t show_##value(struct device *dev,                         \
 259                            struct device_attribute *attr,              \
 260                            char *buf)                                  \
 261{                                                                       \
 262        struct jc42_data *data = jc42_update_device(dev);               \
 263        if (IS_ERR(data))                                               \
 264                return PTR_ERR(data);                                   \
 265        return sprintf(buf, "%d\n", jc42_temp_from_reg(data->value));   \
 266}
 267
 268show(temp_input);
 269show(temp_crit);
 270show(temp_min);
 271show(temp_max);
 272
 273/* read routines for hysteresis values */
 274static ssize_t show_temp_crit_hyst(struct device *dev,
 275                                   struct device_attribute *attr, char *buf)
 276{
 277        struct jc42_data *data = jc42_update_device(dev);
 278        int temp, hyst;
 279
 280        if (IS_ERR(data))
 281                return PTR_ERR(data);
 282
 283        temp = jc42_temp_from_reg(data->temp_crit);
 284        hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
 285                               & JC42_CFG_HYST_MASK];
 286        return sprintf(buf, "%d\n", temp - hyst);
 287}
 288
 289static ssize_t show_temp_max_hyst(struct device *dev,
 290                                  struct device_attribute *attr, char *buf)
 291{
 292        struct jc42_data *data = jc42_update_device(dev);
 293        int temp, hyst;
 294
 295        if (IS_ERR(data))
 296                return PTR_ERR(data);
 297
 298        temp = jc42_temp_from_reg(data->temp_max);
 299        hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
 300                               & JC42_CFG_HYST_MASK];
 301        return sprintf(buf, "%d\n", temp - hyst);
 302}
 303
 304/* write routines */
 305#define set(value, reg) \
 306static ssize_t set_##value(struct device *dev,                          \
 307                           struct device_attribute *attr,               \
 308                           const char *buf, size_t count)               \
 309{                                                                       \
 310        struct i2c_client *client = to_i2c_client(dev);                 \
 311        struct jc42_data *data = i2c_get_clientdata(client);            \
 312        int err, ret = count;                                           \
 313        long val;                                                       \
 314        if (strict_strtol(buf, 10, &val) < 0)                           \
 315                return -EINVAL;                                         \
 316        mutex_lock(&data->update_lock);                                 \
 317        data->value = jc42_temp_to_reg(val, data->extended);            \
 318        err = jc42_write_value(client, reg, data->value);               \
 319        if (err < 0)                                                    \
 320                ret = err;                                              \
 321        mutex_unlock(&data->update_lock);                               \
 322        return ret;                                                     \
 323}
 324
 325set(temp_min, JC42_REG_TEMP_LOWER);
 326set(temp_max, JC42_REG_TEMP_UPPER);
 327set(temp_crit, JC42_REG_TEMP_CRITICAL);
 328
 329/* JC42.4 compliant chips only support four hysteresis values.
 330 * Pick best choice and go from there. */
 331static ssize_t set_temp_crit_hyst(struct device *dev,
 332                                  struct device_attribute *attr,
 333                                  const char *buf, size_t count)
 334{
 335        struct i2c_client *client = to_i2c_client(dev);
 336        struct jc42_data *data = i2c_get_clientdata(client);
 337        unsigned long val;
 338        int diff, hyst;
 339        int err;
 340        int ret = count;
 341
 342        if (strict_strtoul(buf, 10, &val) < 0)
 343                return -EINVAL;
 344
 345        diff = jc42_temp_from_reg(data->temp_crit) - val;
 346        hyst = 0;
 347        if (diff > 0) {
 348                if (diff < 2250)
 349                        hyst = 1;       /* 1.5 degrees C */
 350                else if (diff < 4500)
 351                        hyst = 2;       /* 3.0 degrees C */
 352                else
 353                        hyst = 3;       /* 6.0 degrees C */
 354        }
 355
 356        mutex_lock(&data->update_lock);
 357        data->config = (data->config
 358                        & ~(JC42_CFG_HYST_MASK << JC42_CFG_HYST_SHIFT))
 359          | (hyst << JC42_CFG_HYST_SHIFT);
 360        err = jc42_write_value(client, JC42_REG_CONFIG, data->config);
 361        if (err < 0)
 362                ret = err;
 363        mutex_unlock(&data->update_lock);
 364        return ret;
 365}
 366
 367static ssize_t show_alarm(struct device *dev,
 368                          struct device_attribute *attr, char *buf)
 369{
 370        u16 bit = to_sensor_dev_attr(attr)->index;
 371        struct jc42_data *data = jc42_update_device(dev);
 372        u16 val;
 373
 374        if (IS_ERR(data))
 375                return PTR_ERR(data);
 376
 377        val = data->temp_input;
 378        if (bit != JC42_ALARM_CRIT_BIT && (data->config & JC42_CFG_CRIT_ONLY))
 379                val = 0;
 380        return sprintf(buf, "%u\n", (val >> bit) & 1);
 381}
 382
 383static DEVICE_ATTR(temp1_input, S_IRUGO,
 384                   show_temp_input, NULL);
 385static DEVICE_ATTR(temp1_crit, S_IRUGO,
 386                   show_temp_crit, set_temp_crit);
 387static DEVICE_ATTR(temp1_min, S_IRUGO,
 388                   show_temp_min, set_temp_min);
 389static DEVICE_ATTR(temp1_max, S_IRUGO,
 390                   show_temp_max, set_temp_max);
 391
 392static DEVICE_ATTR(temp1_crit_hyst, S_IRUGO,
 393                   show_temp_crit_hyst, set_temp_crit_hyst);
 394static DEVICE_ATTR(temp1_max_hyst, S_IRUGO,
 395                   show_temp_max_hyst, NULL);
 396
 397static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL,
 398                          JC42_ALARM_CRIT_BIT);
 399static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
 400                          JC42_ALARM_MIN_BIT);
 401static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
 402                          JC42_ALARM_MAX_BIT);
 403
 404static struct attribute *jc42_attributes[] = {
 405        &dev_attr_temp1_input.attr,
 406        &dev_attr_temp1_crit.attr,
 407        &dev_attr_temp1_min.attr,
 408        &dev_attr_temp1_max.attr,
 409        &dev_attr_temp1_crit_hyst.attr,
 410        &dev_attr_temp1_max_hyst.attr,
 411        &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
 412        &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
 413        &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
 414        NULL
 415};
 416
 417static mode_t jc42_attribute_mode(struct kobject *kobj,
 418                                  struct attribute *attr, int index)
 419{
 420        struct device *dev = container_of(kobj, struct device, kobj);
 421        struct i2c_client *client = to_i2c_client(dev);
 422        struct jc42_data *data = i2c_get_clientdata(client);
 423        unsigned int config = data->config;
 424        bool readonly;
 425
 426        if (attr == &dev_attr_temp1_crit.attr)
 427                readonly = config & JC42_CFG_TCRIT_LOCK;
 428        else if (attr == &dev_attr_temp1_min.attr ||
 429                 attr == &dev_attr_temp1_max.attr)
 430                readonly = config & JC42_CFG_EVENT_LOCK;
 431        else if (attr == &dev_attr_temp1_crit_hyst.attr)
 432                readonly = config & (JC42_CFG_EVENT_LOCK | JC42_CFG_TCRIT_LOCK);
 433        else
 434                readonly = true;
 435
 436        return S_IRUGO | (readonly ? 0 : S_IWUSR);
 437}
 438
 439static const struct attribute_group jc42_group = {
 440        .attrs = jc42_attributes,
 441        .is_visible = jc42_attribute_mode,
 442};
 443
 444/* Return 0 if detection is successful, -ENODEV otherwise */
 445static int jc42_detect(struct i2c_client *new_client,
 446                       struct i2c_board_info *info)
 447{
 448        struct i2c_adapter *adapter = new_client->adapter;
 449        int i, config, cap, manid, devid;
 450
 451        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
 452                                     I2C_FUNC_SMBUS_WORD_DATA))
 453                return -ENODEV;
 454
 455        cap = jc42_read_value(new_client, JC42_REG_CAP);
 456        config = jc42_read_value(new_client, JC42_REG_CONFIG);
 457        manid = jc42_read_value(new_client, JC42_REG_MANID);
 458        devid = jc42_read_value(new_client, JC42_REG_DEVICEID);
 459
 460        if (cap < 0 || config < 0 || manid < 0 || devid < 0)
 461                return -ENODEV;
 462
 463        if ((cap & 0xff00) || (config & 0xf800))
 464                return -ENODEV;
 465
 466        for (i = 0; i < ARRAY_SIZE(jc42_chips); i++) {
 467                struct jc42_chips *chip = &jc42_chips[i];
 468                if (manid == chip->manid &&
 469                    (devid & chip->devid_mask) == chip->devid) {
 470                        strlcpy(info->type, "jc42", I2C_NAME_SIZE);
 471                        return 0;
 472                }
 473        }
 474        return -ENODEV;
 475}
 476
 477static int jc42_probe(struct i2c_client *new_client,
 478                      const struct i2c_device_id *id)
 479{
 480        struct jc42_data *data;
 481        int config, cap, err;
 482
 483        data = kzalloc(sizeof(struct jc42_data), GFP_KERNEL);
 484        if (!data) {
 485                err = -ENOMEM;
 486                goto exit;
 487        }
 488
 489        i2c_set_clientdata(new_client, data);
 490        mutex_init(&data->update_lock);
 491
 492        cap = jc42_read_value(new_client, JC42_REG_CAP);
 493        if (cap < 0) {
 494                err = -EINVAL;
 495                goto exit_free;
 496        }
 497        data->extended = !!(cap & JC42_CAP_RANGE);
 498
 499        config = jc42_read_value(new_client, JC42_REG_CONFIG);
 500        if (config < 0) {
 501                err = -EINVAL;
 502                goto exit_free;
 503        }
 504        data->orig_config = config;
 505        if (config & JC42_CFG_SHUTDOWN) {
 506                config &= ~JC42_CFG_SHUTDOWN;
 507                jc42_write_value(new_client, JC42_REG_CONFIG, config);
 508        }
 509        data->config = config;
 510
 511        /* Register sysfs hooks */
 512        err = sysfs_create_group(&new_client->dev.kobj, &jc42_group);
 513        if (err)
 514                goto exit_free;
 515
 516        data->hwmon_dev = hwmon_device_register(&new_client->dev);
 517        if (IS_ERR(data->hwmon_dev)) {
 518                err = PTR_ERR(data->hwmon_dev);
 519                goto exit_remove;
 520        }
 521
 522        return 0;
 523
 524exit_remove:
 525        sysfs_remove_group(&new_client->dev.kobj, &jc42_group);
 526exit_free:
 527        kfree(data);
 528exit:
 529        return err;
 530}
 531
 532static int jc42_remove(struct i2c_client *client)
 533{
 534        struct jc42_data *data = i2c_get_clientdata(client);
 535        hwmon_device_unregister(data->hwmon_dev);
 536        sysfs_remove_group(&client->dev.kobj, &jc42_group);
 537        if (data->config != data->orig_config)
 538                jc42_write_value(client, JC42_REG_CONFIG, data->orig_config);
 539        kfree(data);
 540        return 0;
 541}
 542
 543/* All registers are word-sized. */
 544static int jc42_read_value(struct i2c_client *client, u8 reg)
 545{
 546        int ret = i2c_smbus_read_word_data(client, reg);
 547        if (ret < 0)
 548                return ret;
 549        return swab16(ret);
 550}
 551
 552static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value)
 553{
 554        return i2c_smbus_write_word_data(client, reg, swab16(value));
 555}
 556
 557static struct jc42_data *jc42_update_device(struct device *dev)
 558{
 559        struct i2c_client *client = to_i2c_client(dev);
 560        struct jc42_data *data = i2c_get_clientdata(client);
 561        struct jc42_data *ret = data;
 562        int val;
 563
 564        mutex_lock(&data->update_lock);
 565
 566        if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
 567                val = jc42_read_value(client, JC42_REG_TEMP);
 568                if (val < 0) {
 569                        ret = ERR_PTR(val);
 570                        goto abort;
 571                }
 572                data->temp_input = val;
 573
 574                val = jc42_read_value(client, JC42_REG_TEMP_CRITICAL);
 575                if (val < 0) {
 576                        ret = ERR_PTR(val);
 577                        goto abort;
 578                }
 579                data->temp_crit = val;
 580
 581                val = jc42_read_value(client, JC42_REG_TEMP_LOWER);
 582                if (val < 0) {
 583                        ret = ERR_PTR(val);
 584                        goto abort;
 585                }
 586                data->temp_min = val;
 587
 588                val = jc42_read_value(client, JC42_REG_TEMP_UPPER);
 589                if (val < 0) {
 590                        ret = ERR_PTR(val);
 591                        goto abort;
 592                }
 593                data->temp_max = val;
 594
 595                data->last_updated = jiffies;
 596                data->valid = true;
 597        }
 598abort:
 599        mutex_unlock(&data->update_lock);
 600        return ret;
 601}
 602
 603static int __init sensors_jc42_init(void)
 604{
 605        return i2c_add_driver(&jc42_driver);
 606}
 607
 608static void __exit sensors_jc42_exit(void)
 609{
 610        i2c_del_driver(&jc42_driver);
 611}
 612
 613MODULE_AUTHOR("Guenter Roeck <guenter.roeck@ericsson.com>");
 614MODULE_DESCRIPTION("JC42 driver");
 615MODULE_LICENSE("GPL");
 616
 617module_init(sensors_jc42_init);
 618module_exit(sensors_jc42_exit);
 619