/*
 * linux/arch/arm/mach-at91/board-cpuat91.c
 *
 *  Copyright (C) 2009 Eric Benard - eric@eukrea.com
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

#include <linux/types.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/plat-ram.h>

#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>

#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>

#include <mach/at91rm9200_mc.h>
#include <mach/at91_ramc.h>
#include <mach/cpu.h>

#include "at91_aic.h"
#include "board.h"
#include "generic.h"

static struct gpio_led cpuat91_leds[] = {
        {
                .name                   = "led1",
                .default_trigger        = "heartbeat",
                .active_low             = 1,
                .gpio                   = AT91_PIN_PC0,
        },
};

static void __init cpuat91_init_early(void)
{
        /* Set cpu type: PQFP */
        at91rm9200_set_type(ARCH_REVISON_9200_PQFP);

        /* Initialize processor: 18.432 MHz crystal */
        at91_initialize(18432000);
}

static struct macb_platform_data __initdata cpuat91_eth_data = {
        .phy_irq_pin    = -EINVAL,
        .is_rmii        = 1,
};

static struct at91_usbh_data __initdata cpuat91_usbh_data = {
        .ports          = 1,
        .vbus_pin       = {-EINVAL, -EINVAL},
        .overcurrent_pin= {-EINVAL, -EINVAL},
};

static struct at91_udc_data __initdata cpuat91_udc_data = {
        .vbus_pin       = AT91_PIN_PC15,
        .pullup_pin     = AT91_PIN_PC14,
};

static struct mci_platform_data __initdata cpuat91_mci0_data = {
        .slot[0] = {
                .bus_width      = 4,
                .detect_pin     = AT91_PIN_PC2,
                .wp_pin         = -EINVAL,
        },
};

static struct physmap_flash_data cpuat91_flash_data = {
        .width          = 2,
};

static struct resource cpuat91_flash_resource = {
        .start          = AT91_CHIPSELECT_0,
        .end            = AT91_CHIPSELECT_0 + SZ_16M - 1,
        .flags          = IORESOURCE_MEM,
};

static struct platform_device cpuat91_norflash = {
        .name           = "physmap-flash",
        .id             = 0,
        .dev    = {
                .platform_data  = &cpuat91_flash_data,
        },
        .resource       = &cpuat91_flash_resource,
        .num_resources  = 1,
};

#ifdef CONFIG_MTD_PLATRAM
struct platdata_mtd_ram at91_sram_pdata = {
        .mapname        = "SRAM",
        .bankwidth      = 2,
};

static struct resource at91_sram_resource[] = {
        [0] = {
                .start = AT91RM9200_SRAM_BASE,
                .end   = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1,
                .flags = IORESOURCE_MEM,
        },
};

static struct platform_device at91_sram = {
        .name           = "mtd-ram",
        .id             = 0,
        .resource       = at91_sram_resource,
        .num_resources  = ARRAY_SIZE(at91_sram_resource),
        .dev    = {
                .platform_data = &at91_sram_pdata,
        },
};
#endif /* MTD_PLATRAM */

static struct platform_device *platform_devices[] __initdata = {
        &cpuat91_norflash,
#ifdef CONFIG_MTD_PLATRAM
        &at91_sram,
#endif /* CONFIG_MTD_PLATRAM */
};

static void __init cpuat91_board_init(void)
{
        /* Serial */
        /* DBGU on ttyS0. (Rx & Tx only) */
        at91_register_uart(0, 0, 0);

        /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
        at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
                ATMEL_UART_RTS);

        /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
        at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
                ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
                ATMEL_UART_DCD | ATMEL_UART_RI);

        /* USART2 on ttyS3 (Rx, Tx) */
        at91_register_uart(AT91RM9200_ID_US2, 3, 0);

        /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
        at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
                ATMEL_UART_RTS);
        at91_add_device_serial();
        /* LEDs. */
        at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
        /* Ethernet */
        at91_add_device_eth(&cpuat91_eth_data);
        /* USB Host */
        at91_add_device_usbh(&cpuat91_usbh_data);
        /* USB Device */
        at91_add_device_udc(&cpuat91_udc_data);
        /* MMC */
        at91_add_device_mci(0, &cpuat91_mci0_data);
        /* I2C */
        at91_add_device_i2c(NULL, 0);
        /* Platform devices */
        platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
}

MACHINE_START(CPUAT91, "Eukrea")
        /* Maintainer: Eric Benard - EUKREA Electromatique */
        .init_time      = at91rm9200_timer_init,
        .map_io         = at91_map_io,
        .handle_irq     = at91_aic_handle_irq,
        .init_early     = cpuat91_init_early,
        .init_irq       = at91_init_irq_default,
        .init_machine   = cpuat91_board_init,
MACHINE_END