linux/arch/arm/mach-omap1/board-voiceblue.c
<<
>>
Prefs
   1/*
   2 * linux/arch/arm/mach-omap1/board-voiceblue.c
   3 *
   4 * Modified from board-generic.c
   5 *
   6 * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
   7 *
   8 * Code for OMAP5910 based VoiceBlue board (VoIP to GSM gateway).
   9 *
  10 * This program is free software; you can redistribute it and/or modify
  11 * it under the terms of the GNU General Public License version 2 as
  12 * published by the Free Software Foundation.
  13 */
  14
  15#include <linux/delay.h>
  16#include <linux/gpio.h>
  17#include <linux/platform_device.h>
  18#include <linux/interrupt.h>
  19#include <linux/irq.h>
  20#include <linux/init.h>
  21#include <linux/kernel.h>
  22#include <linux/mtd/physmap.h>
  23#include <linux/notifier.h>
  24#include <linux/reboot.h>
  25#include <linux/serial_8250.h>
  26#include <linux/serial_reg.h>
  27#include <linux/smc91x.h>
  28#include <linux/export.h>
  29
  30#include <asm/mach-types.h>
  31#include <asm/mach/arch.h>
  32#include <asm/mach/map.h>
  33
  34#include <mach/board-voiceblue.h>
  35#include <mach/flash.h>
  36#include <mach/mux.h>
  37#include <mach/tc.h>
  38
  39#include <mach/hardware.h>
  40#include <mach/usb.h>
  41
  42#include "common.h"
  43
  44static struct plat_serial8250_port voiceblue_ports[] = {
  45        {
  46                .mapbase        = (unsigned long)(OMAP_CS1_PHYS + 0x40000),
  47                .flags          = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
  48                .iotype         = UPIO_MEM,
  49                .regshift       = 1,
  50                .uartclk        = 3686400,
  51        },
  52        {
  53                .mapbase        = (unsigned long)(OMAP_CS1_PHYS + 0x50000),
  54                .flags          = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
  55                .iotype         = UPIO_MEM,
  56                .regshift       = 1,
  57                .uartclk        = 3686400,
  58        },
  59        {
  60                .mapbase        = (unsigned long)(OMAP_CS1_PHYS + 0x60000),
  61                .flags          = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
  62                .iotype         = UPIO_MEM,
  63                .regshift       = 1,
  64                .uartclk        = 3686400,
  65        },
  66        {
  67                .mapbase        = (unsigned long)(OMAP_CS1_PHYS + 0x70000),
  68                .flags          = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
  69                .iotype         = UPIO_MEM,
  70                .regshift       = 1,
  71                .uartclk        = 3686400,
  72        },
  73        { },
  74};
  75
  76static struct platform_device serial_device = {
  77        .name                   = "serial8250",
  78        .id                     = PLAT8250_DEV_PLATFORM1,
  79};
  80
  81static int __init ext_uart_init(void)
  82{
  83        if (!machine_is_voiceblue())
  84                return -ENODEV;
  85
  86        voiceblue_ports[0].irq = gpio_to_irq(12);
  87        voiceblue_ports[1].irq = gpio_to_irq(13);
  88        voiceblue_ports[2].irq = gpio_to_irq(14);
  89        voiceblue_ports[3].irq = gpio_to_irq(15);
  90        serial_device.dev.platform_data = voiceblue_ports;
  91        return platform_device_register(&serial_device);
  92}
  93arch_initcall(ext_uart_init);
  94
  95static struct physmap_flash_data voiceblue_flash_data = {
  96        .width          = 2,
  97        .set_vpp        = omap1_set_vpp,
  98};
  99
 100static struct resource voiceblue_flash_resource = {
 101        .start  = OMAP_CS0_PHYS,
 102        .end    = OMAP_CS0_PHYS + SZ_32M - 1,
 103        .flags  = IORESOURCE_MEM,
 104};
 105
 106static struct platform_device voiceblue_flash_device = {
 107        .name           = "physmap-flash",
 108        .id             = 0,
 109        .dev            = {
 110                .platform_data  = &voiceblue_flash_data,
 111        },
 112        .num_resources  = 1,
 113        .resource       = &voiceblue_flash_resource,
 114};
 115
 116static struct smc91x_platdata voiceblue_smc91x_info = {
 117        .flags  = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 118        .leda   = RPC_LED_100_10,
 119        .ledb   = RPC_LED_TX_RX,
 120};
 121
 122static struct resource voiceblue_smc91x_resources[] = {
 123        [0] = {
 124                .start  = OMAP_CS2_PHYS + 0x300,
 125                .end    = OMAP_CS2_PHYS + 0x300 + 16,
 126                .flags  = IORESOURCE_MEM,
 127        },
 128        [1] = {
 129                .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
 130        },
 131};
 132
 133static struct platform_device voiceblue_smc91x_device = {
 134        .name           = "smc91x",
 135        .id             = 0,
 136        .dev    = {
 137                .platform_data  = &voiceblue_smc91x_info,
 138        },
 139        .num_resources  = ARRAY_SIZE(voiceblue_smc91x_resources),
 140        .resource       = voiceblue_smc91x_resources,
 141};
 142
 143static struct platform_device *voiceblue_devices[] __initdata = {
 144        &voiceblue_flash_device,
 145        &voiceblue_smc91x_device,
 146};
 147
 148static struct omap_usb_config voiceblue_usb_config __initdata = {
 149        .hmc_mode       = 3,
 150        .register_host  = 1,
 151        .register_dev   = 1,
 152        .pins[0]        = 2,
 153        .pins[1]        = 6,
 154        .pins[2]        = 6,
 155};
 156
 157#define MACHINE_PANICED         1
 158#define MACHINE_REBOOTING       2
 159#define MACHINE_REBOOT          4
 160static unsigned long machine_state;
 161
 162static int panic_event(struct notifier_block *this, unsigned long event,
 163         void *ptr)
 164{
 165        if (test_and_set_bit(MACHINE_PANICED, &machine_state))
 166                return NOTIFY_DONE;
 167
 168        /* Flash power LED */
 169        omap_writeb(0x78, OMAP_LPG1_LCR);
 170        omap_writeb(0x01, OMAP_LPG1_PMR);       /* Enable clock */
 171
 172        return NOTIFY_DONE;
 173}
 174
 175static struct notifier_block panic_block = {
 176        .notifier_call  = panic_event,
 177};
 178
 179static int __init voiceblue_setup(void)
 180{
 181        if (!machine_is_voiceblue())
 182                return -ENODEV;
 183
 184        /* Setup panic notifier */
 185        atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
 186
 187        return 0;
 188}
 189postcore_initcall(voiceblue_setup);
 190
 191static int wdt_gpio_state;
 192
 193void voiceblue_wdt_enable(void)
 194{
 195        gpio_direction_output(0, 0);
 196        gpio_set_value(0, 1);
 197        gpio_set_value(0, 0);
 198        wdt_gpio_state = 0;
 199}
 200
 201void voiceblue_wdt_disable(void)
 202{
 203        gpio_set_value(0, 0);
 204        gpio_set_value(0, 1);
 205        gpio_set_value(0, 0);
 206        gpio_direction_input(0);
 207}
 208
 209void voiceblue_wdt_ping(void)
 210{
 211        if (test_bit(MACHINE_REBOOT, &machine_state))
 212                return;
 213
 214        wdt_gpio_state = !wdt_gpio_state;
 215        gpio_set_value(0, wdt_gpio_state);
 216}
 217
 218static void voiceblue_restart(char mode, const char *cmd)
 219{
 220        /*
 221         * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
 222         * "Global Software Reset Affects Traffic Controller Frequency".
 223         */
 224        if (cpu_is_omap5912()) {
 225                omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
 226                omap_writew(0x8, ARM_RSTCT1);
 227        }
 228
 229        set_bit(MACHINE_REBOOT, &machine_state);
 230        voiceblue_wdt_enable();
 231        while (1) ;
 232}
 233
 234EXPORT_SYMBOL(voiceblue_wdt_enable);
 235EXPORT_SYMBOL(voiceblue_wdt_disable);
 236EXPORT_SYMBOL(voiceblue_wdt_ping);
 237
 238static void __init voiceblue_init(void)
 239{
 240        /* mux pins for uarts */
 241        omap_cfg_reg(UART1_TX);
 242        omap_cfg_reg(UART1_RTS);
 243        omap_cfg_reg(UART2_TX);
 244        omap_cfg_reg(UART2_RTS);
 245        omap_cfg_reg(UART3_TX);
 246        omap_cfg_reg(UART3_RX);
 247
 248        /* Watchdog */
 249        gpio_request(0, "Watchdog");
 250        /* smc91x reset */
 251        gpio_request(7, "SMC91x reset");
 252        gpio_direction_output(7, 1);
 253        udelay(2);      /* wait at least 100ns */
 254        gpio_set_value(7, 0);
 255        mdelay(50);     /* 50ms until PHY ready */
 256        /* smc91x interrupt pin */
 257        gpio_request(8, "SMC91x irq");
 258        /* 16C554 reset*/
 259        gpio_request(6, "16C554 reset");
 260        gpio_direction_output(6, 0);
 261        /* 16C554 interrupt pins */
 262        gpio_request(12, "16C554 irq");
 263        gpio_request(13, "16C554 irq");
 264        gpio_request(14, "16C554 irq");
 265        gpio_request(15, "16C554 irq");
 266        irq_set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
 267        irq_set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
 268        irq_set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
 269        irq_set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
 270
 271        voiceblue_smc91x_resources[1].start = gpio_to_irq(8);
 272        voiceblue_smc91x_resources[1].end = gpio_to_irq(8);
 273        platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
 274        omap_serial_init();
 275        omap1_usb_init(&voiceblue_usb_config);
 276        omap_register_i2c_bus(1, 100, NULL, 0);
 277
 278        /* There is a good chance board is going up, so enable power LED
 279         * (it is connected through invertor) */
 280        omap_writeb(0x00, OMAP_LPG1_LCR);
 281        omap_writeb(0x00, OMAP_LPG1_PMR);       /* Disable clock */
 282}
 283
 284MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
 285        /* Maintainer: Ladislav Michl <michl@2n.cz> */
 286        .atag_offset    = 0x100,
 287        .map_io         = omap15xx_map_io,
 288        .init_early     = omap1_init_early,
 289        .init_irq       = omap1_init_irq,
 290        .init_machine   = voiceblue_init,
 291        .init_late      = omap1_init_late,
 292        .init_time      = omap1_timer_init,
 293        .restart        = voiceblue_restart,
 294MACHINE_END
 295