LXR linux/arch/m68k/include/asm/m525xsim.h

   1/****************************************************************************/
   2
   3/*
   4 *      m525xsim.h -- ColdFire 525x System Integration Module support.
   5 *
   6 *      (C) Copyright 2012, Steven king <sfking@fdwdc.com>
   7 *      (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
   8 */
   9
  10/****************************************************************************/
  11#ifndef m525xsim_h
  12#define m525xsim_h
  13/****************************************************************************/
  14
  15/*
  16 *      This header supports ColdFire 5249, 5251 and 5253. There are a few
  17 *      little differences between them, but most of the peripheral support
  18 *      can be used by all of them.
  19 */
  20#define CPU_NAME                "COLDFIRE(m525x)"
  21#define CPU_INSTR_PER_JIFFY     3
  22#define MCF_BUSCLK              (MCF_CLK / 2)
  23
  24#include <asm/m52xxacr.h>
  25
  26/*
  27 *      The 525x has a second MBAR region, define its address.
  28 */
  29#define MCF_MBAR2               0x80000000
  30
  31/*
  32 *      Define the 525x SIM register set addresses.
  33 */
  34#define MCFSIM_RSR              (MCF_MBAR + 0x00)       /* Reset Status */
  35#define MCFSIM_SYPCR            (MCF_MBAR + 0x01)       /* System Protection */
  36#define MCFSIM_SWIVR            (MCF_MBAR + 0x02)       /* SW Watchdog intr */
  37#define MCFSIM_SWSR             (MCF_MBAR + 0x03)       /* SW Watchdog srv */
  38#define MCFSIM_MPARK            (MCF_MBAR + 0x0C)       /* BUS Master Ctrl */
  39#define MCFSIM_IPR              (MCF_MBAR + 0x40)       /* Interrupt Pending */
  40#define MCFSIM_IMR              (MCF_MBAR + 0x44)       /* Interrupt Mask */
  41#define MCFSIM_ICR0             (MCF_MBAR + 0x4c)       /* Intr Ctrl reg 0 */
  42#define MCFSIM_ICR1             (MCF_MBAR + 0x4d)       /* Intr Ctrl reg 1 */
  43#define MCFSIM_ICR2             (MCF_MBAR + 0x4e)       /* Intr Ctrl reg 2 */
  44#define MCFSIM_ICR3             (MCF_MBAR + 0x4f)       /* Intr Ctrl reg 3 */
  45#define MCFSIM_ICR4             (MCF_MBAR + 0x50)       /* Intr Ctrl reg 4 */
  46#define MCFSIM_ICR5             (MCF_MBAR + 0x51)       /* Intr Ctrl reg 5 */
  47#define MCFSIM_ICR6             (MCF_MBAR + 0x52)       /* Intr Ctrl reg 6 */
  48#define MCFSIM_ICR7             (MCF_MBAR + 0x53)       /* Intr Ctrl reg 7 */
  49#define MCFSIM_ICR8             (MCF_MBAR + 0x54)       /* Intr Ctrl reg 8 */
  50#define MCFSIM_ICR9             (MCF_MBAR + 0x55)       /* Intr Ctrl reg 9 */
  51#define MCFSIM_ICR10            (MCF_MBAR + 0x56)       /* Intr Ctrl reg 10 */
  52#define MCFSIM_ICR11            (MCF_MBAR + 0x57)       /* Intr Ctrl reg 11 */
  53
  54#define MCFSIM_CSAR0            (MCF_MBAR + 0x80)       /* CS 0 Address reg */
  55#define MCFSIM_CSMR0            (MCF_MBAR + 0x84)       /* CS 0 Mask reg */
  56#define MCFSIM_CSCR0            (MCF_MBAR + 0x8a)       /* CS 0 Control reg */
  57#define MCFSIM_CSAR1            (MCF_MBAR + 0x8c)       /* CS 1 Address reg */
  58#define MCFSIM_CSMR1            (MCF_MBAR + 0x90)       /* CS 1 Mask reg */
  59#define MCFSIM_CSCR1            (MCF_MBAR + 0x96)       /* CS 1 Control reg */
  60#define MCFSIM_CSAR2            (MCF_MBAR + 0x98)       /* CS 2 Address reg */
  61#define MCFSIM_CSMR2            (MCF_MBAR + 0x9c)       /* CS 2 Mask reg */
  62#define MCFSIM_CSCR2            (MCF_MBAR + 0xa2)       /* CS 2 Control reg */
  63#define MCFSIM_CSAR3            (MCF_MBAR + 0xa4)       /* CS 3 Address reg */
  64#define MCFSIM_CSMR3            (MCF_MBAR + 0xa8)       /* CS 3 Mask reg */
  65#define MCFSIM_CSCR3            (MCF_MBAR + 0xae)       /* CS 3 Control reg */
  66#define MCFSIM_CSAR4            (MCF_MBAR + 0xb0)       /* CS 4 Address reg */
  67#define MCFSIM_CSMR4            (MCF_MBAR + 0xb4)       /* CS 4 Mask reg */
  68#define MCFSIM_CSCR4            (MCF_MBAR + 0xba)       /* CS 4 Control reg */
  69
  70#define MCFSIM_DCR              (MCF_MBAR + 0x100)      /* DRAM Control */
  71#define MCFSIM_DACR0            (MCF_MBAR + 0x108)      /* DRAM 0 Addr/Ctrl */
  72#define MCFSIM_DMR0             (MCF_MBAR + 0x10c)      /* DRAM 0 Mask */
  73#define MCFSIM_DACR1            (MCF_MBAR + 0x110)      /* DRAM 1 Addr/Ctrl */
  74#define MCFSIM_DMR1             (MCF_MBAR + 0x114)      /* DRAM 1 Mask */
  75
  76/*
  77 * Secondary Interrupt Controller (in MBAR2)
  78*/
  79#define MCFINTC2_INTBASE        (MCF_MBAR2 + 0x168)     /* Base Vector Reg */
  80#define MCFINTC2_INTPRI1        (MCF_MBAR2 + 0x140)     /* 0-7 priority */
  81#define MCFINTC2_INTPRI2        (MCF_MBAR2 + 0x144)     /* 8-15 priority */
  82#define MCFINTC2_INTPRI3        (MCF_MBAR2 + 0x148)     /* 16-23 priority */
  83#define MCFINTC2_INTPRI4        (MCF_MBAR2 + 0x14c)     /* 24-31 priority */
  84#define MCFINTC2_INTPRI5        (MCF_MBAR2 + 0x150)     /* 32-39 priority */
  85#define MCFINTC2_INTPRI6        (MCF_MBAR2 + 0x154)     /* 40-47 priority */
  86#define MCFINTC2_INTPRI7        (MCF_MBAR2 + 0x158)     /* 48-55 priority */
  87#define MCFINTC2_INTPRI8        (MCF_MBAR2 + 0x15c)     /* 56-63 priority */
  88
  89#define MCFINTC2_INTPRI_REG(i)  (MCFINTC2_INTPRI1 + \
  90                                ((((i) - MCFINTC2_VECBASE) / 8) * 4))
  91#define MCFINTC2_INTPRI_BITS(b, i)      ((b) << (((i) % 8) * 4))
  92
  93/*
  94 *      Timer module.
  95 */
  96#define MCFTIMER_BASE1          (MCF_MBAR + 0x140)      /* Base of TIMER1 */
  97#define MCFTIMER_BASE2          (MCF_MBAR + 0x180)      /* Base of TIMER2 */
  98
  99/*
 100 *      UART module.
 101 */
 102#define MCFUART_BASE0           (MCF_MBAR + 0x1c0)      /* Base address UART0 */
 103#define MCFUART_BASE1           (MCF_MBAR + 0x200)      /* Base address UART1 */
 104
 105/*
 106 *      QSPI module.
 107 */
 108#define MCFQSPI_BASE            (MCF_MBAR + 0x300)      /* Base address QSPI */
 109#define MCFQSPI_SIZE            0x40                    /* Register set size */
 110
 111#ifdef CONFIG_M5249
 112#define MCFQSPI_CS0             29
 113#define MCFQSPI_CS1             24
 114#define MCFQSPI_CS2             21
 115#define MCFQSPI_CS3             22
 116#else
 117#define MCFQSPI_CS0             15
 118#define MCFQSPI_CS1             16
 119#define MCFQSPI_CS2             24
 120#define MCFQSPI_CS3             28
 121#endif
 122
 123/*
 124 *      I2C module.
 125 */
 126#define MCFI2C_BASE0            (MCF_MBAR + 0x280)      /* Base addreess I2C0 */
 127#define MCFI2C_SIZE0            0x20                    /* Register set size */
 128
 129#define MCFI2C_BASE1            (MCF_MBAR2 + 0x440)     /* Base addreess I2C1 */
 130#define MCFI2C_SIZE1            0x20                    /* Register set size */
 131
 132/*
 133 *      DMA unit base addresses.
 134 */
 135#define MCFDMA_BASE0            (MCF_MBAR + 0x300)      /* Base address DMA 0 */
 136#define MCFDMA_BASE1            (MCF_MBAR + 0x340)      /* Base address DMA 1 */
 137#define MCFDMA_BASE2            (MCF_MBAR + 0x380)      /* Base address DMA 2 */
 138#define MCFDMA_BASE3            (MCF_MBAR + 0x3C0)      /* Base address DMA 3 */
 139
 140/*
 141 *      Some symbol defines for the above...
 142 */
 143#define MCFSIM_SWDICR           MCFSIM_ICR0     /* Watchdog timer ICR */
 144#define MCFSIM_TIMER1ICR        MCFSIM_ICR1     /* Timer 1 ICR */
 145#define MCFSIM_TIMER2ICR        MCFSIM_ICR2     /* Timer 2 ICR */
 146#define MCFSIM_I2CICR           MCFSIM_ICR3     /* I2C ICR */
 147#define MCFSIM_UART1ICR         MCFSIM_ICR4     /* UART 1 ICR */
 148#define MCFSIM_UART2ICR         MCFSIM_ICR5     /* UART 2 ICR */
 149#define MCFSIM_DMA0ICR          MCFSIM_ICR6     /* DMA 0 ICR */
 150#define MCFSIM_DMA1ICR          MCFSIM_ICR7     /* DMA 1 ICR */
 151#define MCFSIM_DMA2ICR          MCFSIM_ICR8     /* DMA 2 ICR */
 152#define MCFSIM_DMA3ICR          MCFSIM_ICR9     /* DMA 3 ICR */
 153#define MCFSIM_QSPIICR          MCFSIM_ICR10    /* QSPI ICR */
 154
 155/*
 156 *      Define system peripheral IRQ usage.
 157 */
 158#define MCF_IRQ_QSPI            28              /* QSPI, Level 4 */
 159#define MCF_IRQ_I2C0            29
 160#define MCF_IRQ_TIMER           30              /* Timer0, Level 6 */
 161#define MCF_IRQ_PROFILER        31              /* Timer1, Level 7 */
 162
 163#define MCF_IRQ_UART0           73              /* UART0 */
 164#define MCF_IRQ_UART1           74              /* UART1 */
 165
 166/*
 167 * Define the base interrupt for the second interrupt controller.
 168 * We set it to 128, out of the way of the base interrupts, and plenty
 169 * of room for its 64 interrupts.
 170 */
 171#define MCFINTC2_VECBASE        128
 172
 173#define MCF_IRQ_GPIO0           (MCFINTC2_VECBASE + 32)
 174#define MCF_IRQ_GPIO1           (MCFINTC2_VECBASE + 33)
 175#define MCF_IRQ_GPIO2           (MCFINTC2_VECBASE + 34)
 176#define MCF_IRQ_GPIO3           (MCFINTC2_VECBASE + 35)
 177#define MCF_IRQ_GPIO4           (MCFINTC2_VECBASE + 36)
 178#define MCF_IRQ_GPIO5           (MCFINTC2_VECBASE + 37)
 179#define MCF_IRQ_GPIO6           (MCFINTC2_VECBASE + 38)
 180#define MCF_IRQ_GPIO7           (MCFINTC2_VECBASE + 39)
 181
 182#define MCF_IRQ_USBWUP          (MCFINTC2_VECBASE + 40)
 183#define MCF_IRQ_I2C1            (MCFINTC2_VECBASE + 62)
 184
 185/*
 186 *      General purpose IO registers (in MBAR2).
 187 */
 188#define MCFSIM2_GPIOREAD        (MCF_MBAR2 + 0x000)     /* GPIO read values */
 189#define MCFSIM2_GPIOWRITE       (MCF_MBAR2 + 0x004)     /* GPIO write values */
 190#define MCFSIM2_GPIOENABLE      (MCF_MBAR2 + 0x008)     /* GPIO enabled */
 191#define MCFSIM2_GPIOFUNC        (MCF_MBAR2 + 0x00C)     /* GPIO function */
 192#define MCFSIM2_GPIO1READ       (MCF_MBAR2 + 0x0B0)     /* GPIO1 read values */
 193#define MCFSIM2_GPIO1WRITE      (MCF_MBAR2 + 0x0B4)     /* GPIO1 write values */
 194#define MCFSIM2_GPIO1ENABLE     (MCF_MBAR2 + 0x0B8)     /* GPIO1 enabled */
 195#define MCFSIM2_GPIO1FUNC       (MCF_MBAR2 + 0x0BC)     /* GPIO1 function */
 196
 197#define MCFSIM2_GPIOINTSTAT     (MCF_MBAR2 + 0xc0)      /* GPIO intr status */
 198#define MCFSIM2_GPIOINTCLEAR    (MCF_MBAR2 + 0xc0)      /* GPIO intr clear */
 199#define MCFSIM2_GPIOINTENABLE   (MCF_MBAR2 + 0xc4)      /* GPIO intr enable */
 200
 201#define MCFSIM2_DMAROUTE        (MCF_MBAR2 + 0x188)     /* DMA routing */
 202#define MCFSIM2_IDECONFIG1      (MCF_MBAR2 + 0x18c)     /* IDEconfig1 */
 203#define MCFSIM2_IDECONFIG2      (MCF_MBAR2 + 0x190)     /* IDEconfig2 */
 204
 205/*
 206 * Generic GPIO support
 207 */
 208#define MCFGPIO_PIN_MAX         64
 209#ifdef CONFIG_M5249
 210#define MCFGPIO_IRQ_MAX         -1
 211#define MCFGPIO_IRQ_VECBASE     -1
 212#else
 213#define MCFGPIO_IRQ_MAX         7
 214#define MCFGPIO_IRQ_VECBASE     MCF_IRQ_GPIO0
 215#endif
 216
 217/****************************************************************************/
 218
 219#ifdef __ASSEMBLER__
 220#ifdef CONFIG_M5249C3
 221/*
 222 *      The M5249C3 board needs a little help getting all its SIM devices
 223 *      initialized at kernel start time. dBUG doesn't set much up, so
 224 *      we need to do it manually.
 225 */
 226.macro m5249c3_setup
 227        /*
 228         *      Set MBAR1 and MBAR2, just incase they are not set.
 229         */
 230        movel   #0x10000001,%a0
 231        movec   %a0,%MBAR                       /* map MBAR region */
 232        subql   #1,%a0                          /* get MBAR address in a0 */
 233
 234        movel   #0x80000001,%a1
 235        movec   %a1,#3086                       /* map MBAR2 region */
 236        subql   #1,%a1                          /* get MBAR2 address in a1 */
 237
 238        /*
 239         *      Move secondary interrupts to their base (128).
 240         */
 241        moveb   #MCFINTC2_VECBASE,%d0
 242        moveb   %d0,0x16b(%a1)                  /* interrupt base register */
 243
 244        /*
 245         *      Work around broken CSMR0/DRAM vector problem.
 246         */
 247        movel   #0x001F0021,%d0                 /* disable C/I bit */
 248        movel   %d0,0x84(%a0)                   /* set CSMR0 */
 249
 250        /*
 251         *      Disable the PLL firstly. (Who knows what state it is
 252         *      in here!).
 253         */
 254        movel   0x180(%a1),%d0                  /* get current PLL value */
 255        andl    #0xfffffffe,%d0                 /* PLL bypass first */
 256        movel   %d0,0x180(%a1)                  /* set PLL register */
 257        nop
 258
 259#if CONFIG_CLOCK_FREQ == 140000000
 260        /*
 261         *      Set initial clock frequency. This assumes M5249C3 board
 262         *      is fitted with 11.2896MHz crystal. It will program the
 263         *      PLL for 140MHz. Lets go fast :-)
 264         */
 265        movel   #0x125a40f0,%d0                 /* set for 140MHz */
 266        movel   %d0,0x180(%a1)                  /* set PLL register */
 267        orl     #0x1,%d0
 268        movel   %d0,0x180(%a1)                  /* set PLL register */
 269#endif
 270
 271        /*
 272         *      Setup CS1 for ethernet controller.
 273         *      (Setup as per M5249C3 doco).
 274         */
 275        movel  #0xe0000000,%d0                  /* CS1 mapped at 0xe0000000 */
 276        movel  %d0,0x8c(%a0)
 277        movel  #0x001f0021,%d0                  /* CS1 size of 1Mb */
 278        movel  %d0,0x90(%a0)
 279        movew  #0x0080,%d0                      /* CS1 = 16bit port, AA */
 280        movew  %d0,0x96(%a0)
 281
 282        /*
 283         *      Setup CS2 for IDE interface.
 284         */
 285        movel   #0x50000000,%d0                 /* CS2 mapped at 0x50000000 */
 286        movel   %d0,0x98(%a0)
 287        movel   #0x001f0001,%d0                 /* CS2 size of 1MB */
 288        movel   %d0,0x9c(%a0)
 289        movew   #0x0080,%d0                     /* CS2 = 16bit, TA */
 290        movew   %d0,0xa2(%a0)
 291
 292        movel   #0x00107000,%d0                 /* IDEconfig1 */
 293        movel   %d0,0x18c(%a1)
 294        movel   #0x000c0400,%d0                 /* IDEconfig2 */
 295        movel   %d0,0x190(%a1)
 296
 297        movel   #0x00080000,%d0                 /* GPIO19, IDE reset bit */
 298        orl     %d0,0xc(%a1)                    /* function GPIO19 */
 299        orl     %d0,0x8(%a1)                    /* enable GPIO19 as output */
 300        orl     %d0,0x4(%a1)                    /* de-assert IDE reset */
 301.endm
 302
 303#define PLATFORM_SETUP  m5249c3_setup
 304
 305#endif /* CONFIG_M5249C3 */
 306#endif /* __ASSEMBLER__ */
 307/****************************************************************************/
 308#endif  /* m525xsim_h */
 309