LXR linux/drivers/net/fddi/Kconfig

   1#
   2# FDDI network device configuration
   3#
   4
   5config FDDI
   6        tristate "FDDI driver support"
   7        depends on PCI || EISA || TC
   8        ---help---
   9          Fiber Distributed Data Interface is a high speed local area network
  10          design; essentially a replacement for high speed Ethernet. FDDI can
  11          run over copper or fiber. If you are connected to such a network and
  12          want a driver for the FDDI card in your computer, say Y here (and
  13          then also Y to the driver for your FDDI card, below). Most people
  14          will say N.
  15
  16if FDDI
  17
  18config DEFXX
  19        tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
  20        depends on FDDI && (PCI || EISA || TC)
  21        ---help---
  22          This is support for the DIGITAL series of TURBOchannel (DEFTA),
  23          EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
  24          to a local FDDI network.
  25
  26          To compile this driver as a module, choose M here: the module
  27          will be called defxx.  If unsure, say N.
  28
  29config DEFXX_MMIO
  30        bool
  31        prompt "Use MMIO instead of PIO" if PCI || EISA
  32        depends on DEFXX
  33        default n if PCI || EISA
  34        default y
  35        ---help---
  36          This instructs the driver to use EISA or PCI memory-mapped I/O
  37          (MMIO) as appropriate instead of programmed I/O ports (PIO).
  38          Enabling this gives an improvement in processing time in parts
  39          of the driver, but it may cause problems with EISA (DEFEA)
  40          adapters.  TURBOchannel does not have the concept of I/O ports,
  41          so MMIO is always used for these (DEFTA) adapters.
  42
  43          If unsure, say N.
  44
  45config SKFP
  46        tristate "SysKonnect FDDI PCI support"
  47        depends on FDDI && PCI
  48        select BITREVERSE
  49        ---help---
  50          Say Y here if you have a SysKonnect FDDI PCI adapter.
  51          The following adapters are supported by this driver:
  52          - SK-5521 (SK-NET FDDI-UP)
  53          - SK-5522 (SK-NET FDDI-UP DAS)
  54          - SK-5541 (SK-NET FDDI-FP)
  55          - SK-5543 (SK-NET FDDI-LP)
  56          - SK-5544 (SK-NET FDDI-LP DAS)
  57          - SK-5821 (SK-NET FDDI-UP64)
  58          - SK-5822 (SK-NET FDDI-UP64 DAS)
  59          - SK-5841 (SK-NET FDDI-FP64)
  60          - SK-5843 (SK-NET FDDI-LP64)
  61          - SK-5844 (SK-NET FDDI-LP64 DAS)
  62          - Netelligent 100 FDDI DAS Fibre SC
  63          - Netelligent 100 FDDI SAS Fibre SC
  64          - Netelligent 100 FDDI DAS UTP
  65          - Netelligent 100 FDDI SAS UTP
  66          - Netelligent 100 FDDI SAS Fibre MIC
  67
  68          Read <file:Documentation/networking/skfp.txt> for information about
  69          the driver.
  70
  71          Questions concerning this driver can be addressed to:
  72          <linux@syskonnect.de>
  73
  74          To compile this driver as a module, choose M here: the module
  75          will be called skfp.  This is recommended.
  76
  77endif # FDDI
  78