/****************************************************************************
 *
 * Driver for the IFX 6x60 spi modem.
 *
 * Copyright (C) 2008 Option International
 * Copyright (C) 2008 Filip Aben <f.aben@option.com>
 *                    Denis Joseph Barrow <d.barow@option.com>
 *                    Jan Dumon <j.dumon@option.com>
 *
 * Copyright (C) 2009, 2010 Intel Corp
 * Russ Gorby <russ.gorby@intel.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301,
 * USA
 *
 * Driver modified by Intel from Option gtm501l_spi.c
 *
 * Notes
 * o    The driver currently assumes a single device only. If you need to
 *      change this then look for saved_ifx_dev and add a device lookup
 * o    The driver is intended to be big-endian safe but has never been
 *      tested that way (no suitable hardware). There are a couple of FIXME
 *      notes by areas that may need addressing
 * o    Some of the GPIO naming/setup assumptions may need revisiting if
 *      you need to use this driver for another platform.
 *
 *****************************************************************************/
#include <linux/dma-mapping.h>
#include <linux/module.h>
#include <linux/termios.h>
#include <linux/tty.h>
#include <linux/device.h>
#include <linux/spi/spi.h>
#include <linux/kfifo.h>
#include <linux/tty_flip.h>
#include <linux/timer.h>
#include <linux/serial.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/rfkill.h>
#include <linux/fs.h>
#include <linux/ip.h>
#include <linux/dmapool.h>
#include <linux/gpio.h>
#include <linux/sched.h>
#include <linux/time.h>
#include <linux/wait.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
#include <linux/spi/ifx_modem.h>
#include <linux/delay.h>
#include <linux/reboot.h>

#include "ifx6x60.h"

#define IFX_SPI_MORE_MASK               0x10
#define IFX_SPI_MORE_BIT                4       /* bit position in u8 */
#define IFX_SPI_CTS_BIT                 6       /* bit position in u8 */
#define IFX_SPI_MODE                    SPI_MODE_1
#define IFX_SPI_TTY_ID                  0
#define IFX_SPI_TIMEOUT_SEC             2
#define IFX_SPI_HEADER_0                (-1)
#define IFX_SPI_HEADER_F                (-2)

#define PO_POST_DELAY           200
#define IFX_MDM_RST_PMU 4

/* forward reference */
static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev);
static int ifx_modem_reboot_callback(struct notifier_block *nfb,
                                unsigned long event, void *data);
static int ifx_modem_power_off(struct ifx_spi_device *ifx_dev);

/* local variables */
static int spi_bpw = 16;                /* 8, 16 or 32 bit word length */
static struct tty_driver *tty_drv;
static struct ifx_spi_device *saved_ifx_dev;
static struct lock_class_key ifx_spi_key;

static struct notifier_block ifx_modem_reboot_notifier_block = {
        .notifier_call = ifx_modem_reboot_callback,
};

static int ifx_modem_power_off(struct ifx_spi_device *ifx_dev)
{
        gpio_set_value(IFX_MDM_RST_PMU, 1);
        msleep(PO_POST_DELAY);

        return 0;
}

static int ifx_modem_reboot_callback(struct notifier_block *nfb,
                                 unsigned long event, void *data)
{
        if (saved_ifx_dev)
                ifx_modem_power_off(saved_ifx_dev);
        else
                pr_warn("no ifx modem active;\n");

        return NOTIFY_OK;
}

/* GPIO/GPE settings */

/**
 *      mrdy_set_high           -       set MRDY GPIO
 *      @ifx: device we are controlling
 *
 */
static inline void mrdy_set_high(struct ifx_spi_device *ifx)
{
        gpio_set_value(ifx->gpio.mrdy, 1);
}

/**
 *      mrdy_set_low            -       clear MRDY GPIO
 *      @ifx: device we are controlling
 *
 */
static inline void mrdy_set_low(struct ifx_spi_device *ifx)
{
        gpio_set_value(ifx->gpio.mrdy, 0);
}

/**
 *      ifx_spi_power_state_set
 *      @ifx_dev: our SPI device
 *      @val: bits to set
 *
 *      Set bit in power status and signal power system if status becomes non-0
 */
static void
ifx_spi_power_state_set(struct ifx_spi_device *ifx_dev, unsigned char val)
{
        unsigned long flags;

        spin_lock_irqsave(&ifx_dev->power_lock, flags);

        /*
         * if power status is already non-0, just update, else
         * tell power system
         */
        if (!ifx_dev->power_status)
                pm_runtime_get(&ifx_dev->spi_dev->dev);
        ifx_dev->power_status |= val;

        spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
}

/**
 *      ifx_spi_power_state_clear       -       clear power bit
 *      @ifx_dev: our SPI device
 *      @val: bits to clear
 *
 *      clear bit in power status and signal power system if status becomes 0
 */
static void
ifx_spi_power_state_clear(struct ifx_spi_device *ifx_dev, unsigned char val)
{
        unsigned long flags;

        spin_lock_irqsave(&ifx_dev->power_lock, flags);

        if (ifx_dev->power_status) {
                ifx_dev->power_status &= ~val;
                if (!ifx_dev->power_status)
                        pm_runtime_put(&ifx_dev->spi_dev->dev);
        }

        spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
}

/**
 *      swap_buf_8
 *      @buf: our buffer
 *      @len : number of bytes (not words) in the buffer
 *      @end: end of buffer
 *
 *      Swap the contents of a buffer into big endian format
 */
static inline void swap_buf_8(unsigned char *buf, int len, void *end)
{
        /* don't swap buffer if SPI word width is 8 bits */
        return;
}

/**
 *      swap_buf_16
 *      @buf: our buffer
 *      @len : number of bytes (not words) in the buffer
 *      @end: end of buffer
 *
 *      Swap the contents of a buffer into big endian format
 */
static inline void swap_buf_16(unsigned char *buf, int len, void *end)
{
        int n;

        u16 *buf_16 = (u16 *)buf;
        len = ((len + 1) >> 1);
        if ((void *)&buf_16[len] > end) {
                pr_err("swap_buf_16: swap exceeds boundary (%p > %p)!",
                       &buf_16[len], end);
                return;
        }
        for (n = 0; n < len; n++) {
                *buf_16 = cpu_to_be16(*buf_16);
                buf_16++;
        }
}

/**
 *      swap_buf_32
 *      @buf: our buffer
 *      @len : number of bytes (not words) in the buffer
 *      @end: end of buffer
 *
 *      Swap the contents of a buffer into big endian format
 */
static inline void swap_buf_32(unsigned char *buf, int len, void *end)
{
        int n;

        u32 *buf_32 = (u32 *)buf;
        len = (len + 3) >> 2;

        if ((void *)&buf_32[len] > end) {
                pr_err("swap_buf_32: swap exceeds boundary (%p > %p)!\n",
                       &buf_32[len], end);
                return;
        }
        for (n = 0; n < len; n++) {
                *buf_32 = cpu_to_be32(*buf_32);
                buf_32++;
        }
}

/**
 *      mrdy_assert             -       assert MRDY line
 *      @ifx_dev: our SPI device
 *
 *      Assert mrdy and set timer to wait for SRDY interrupt, if SRDY is low
 *      now.
 *
 *      FIXME: Can SRDY even go high as we are running this code ?
 */
static void mrdy_assert(struct ifx_spi_device *ifx_dev)
{
        int val = gpio_get_value(ifx_dev->gpio.srdy);
        if (!val) {
                if (!test_and_set_bit(IFX_SPI_STATE_TIMER_PENDING,
                                      &ifx_dev->flags)) {
                        mod_timer(&ifx_dev->spi_timer,jiffies + IFX_SPI_TIMEOUT_SEC*HZ);

                }
        }
        ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_DATA_PENDING);
        mrdy_set_high(ifx_dev);
}

/**
 *      ifx_spi_timeout         -       SPI timeout
 *      @arg: our SPI device
 *
 *      The SPI has timed out: hang up the tty. Users will then see a hangup
 *      and error events.
 */
static void ifx_spi_timeout(unsigned long arg)
{
        struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *)arg;

        dev_warn(&ifx_dev->spi_dev->dev, "*** SPI Timeout ***");
        tty_port_tty_hangup(&ifx_dev->tty_port, false);
        mrdy_set_low(ifx_dev);
        clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
}

/* char/tty operations */

/**
 *      ifx_spi_tiocmget        -       get modem lines
 *      @tty: our tty device
 *      @filp: file handle issuing the request
 *
 *      Map the signal state into Linux modem flags and report the value
 *      in Linux terms
 */
static int ifx_spi_tiocmget(struct tty_struct *tty)
{
        unsigned int value;
        struct ifx_spi_device *ifx_dev = tty->driver_data;

        value =
        (test_bit(IFX_SPI_RTS, &ifx_dev->signal_state) ? TIOCM_RTS : 0) |
        (test_bit(IFX_SPI_DTR, &ifx_dev->signal_state) ? TIOCM_DTR : 0) |
        (test_bit(IFX_SPI_CTS, &ifx_dev->signal_state) ? TIOCM_CTS : 0) |
        (test_bit(IFX_SPI_DSR, &ifx_dev->signal_state) ? TIOCM_DSR : 0) |
        (test_bit(IFX_SPI_DCD, &ifx_dev->signal_state) ? TIOCM_CAR : 0) |
        (test_bit(IFX_SPI_RI, &ifx_dev->signal_state) ? TIOCM_RNG : 0);
        return value;
}

/**
 *      ifx_spi_tiocmset        -       set modem bits
 *      @tty: the tty structure
 *      @set: bits to set
 *      @clear: bits to clear
 *
 *      The IFX6x60 only supports DTR and RTS. Set them accordingly
 *      and flag that an update to the modem is needed.
 *
 *      FIXME: do we need to kick the tranfers when we do this ?
 */
static int ifx_spi_tiocmset(struct tty_struct *tty,
                            unsigned int set, unsigned int clear)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;

        if (set & TIOCM_RTS)
                set_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
        if (set & TIOCM_DTR)
                set_bit(IFX_SPI_DTR, &ifx_dev->signal_state);
        if (clear & TIOCM_RTS)
                clear_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
        if (clear & TIOCM_DTR)
                clear_bit(IFX_SPI_DTR, &ifx_dev->signal_state);

        set_bit(IFX_SPI_UPDATE, &ifx_dev->signal_state);
        return 0;
}

/**
 *      ifx_spi_open    -       called on tty open
 *      @tty: our tty device
 *      @filp: file handle being associated with the tty
 *
 *      Open the tty interface. We let the tty_port layer do all the work
 *      for us.
 *
 *      FIXME: Remove single device assumption and saved_ifx_dev
 */
static int ifx_spi_open(struct tty_struct *tty, struct file *filp)
{
        return tty_port_open(&saved_ifx_dev->tty_port, tty, filp);
}

/**
 *      ifx_spi_close   -       called when our tty closes
 *      @tty: the tty being closed
 *      @filp: the file handle being closed
 *
 *      Perform the close of the tty. We use the tty_port layer to do all
 *      our hard work.
 */
static void ifx_spi_close(struct tty_struct *tty, struct file *filp)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;
        tty_port_close(&ifx_dev->tty_port, tty, filp);
        /* FIXME: should we do an ifx_spi_reset here ? */
}

/**
 *      ifx_decode_spi_header   -       decode received header
 *      @buffer: the received data
 *      @length: decoded length
 *      @more: decoded more flag
 *      @received_cts: status of cts we received
 *
 *      Note how received_cts is handled -- if header is all F it is left
 *      the same as it was, if header is all 0 it is set to 0 otherwise it is
 *      taken from the incoming header.
 *
 *      FIXME: endianness
 */
static int ifx_spi_decode_spi_header(unsigned char *buffer, int *length,
                        unsigned char *more, unsigned char *received_cts)
{
        u16 h1;
        u16 h2;
        u16 *in_buffer = (u16 *)buffer;

        h1 = *in_buffer;
        h2 = *(in_buffer+1);

        if (h1 == 0 && h2 == 0) {
                *received_cts = 0;
                return IFX_SPI_HEADER_0;
        } else if (h1 == 0xffff && h2 == 0xffff) {
                /* spi_slave_cts remains as it was */
                return IFX_SPI_HEADER_F;
        }

        *length = h1 & 0xfff;   /* upper bits of byte are flags */
        *more = (buffer[1] >> IFX_SPI_MORE_BIT) & 1;
        *received_cts = (buffer[3] >> IFX_SPI_CTS_BIT) & 1;
        return 0;
}

/**
 *      ifx_setup_spi_header    -       set header fields
 *      @txbuffer: pointer to start of SPI buffer
 *      @tx_count: bytes
 *      @more: indicate if more to follow
 *
 *      Format up an SPI header for a transfer
 *
 *      FIXME: endianness?
 */
static void ifx_spi_setup_spi_header(unsigned char *txbuffer, int tx_count,
                                        unsigned char more)
{
        *(u16 *)(txbuffer) = tx_count;
        *(u16 *)(txbuffer+2) = IFX_SPI_PAYLOAD_SIZE;
        txbuffer[1] |= (more << IFX_SPI_MORE_BIT) & IFX_SPI_MORE_MASK;
}

/**
 *      ifx_spi_prepare_tx_buffer       -       prepare transmit frame
 *      @ifx_dev: our SPI device
 *
 *      The transmit buffr needs a header and various other bits of
 *      information followed by as much data as we can pull from the FIFO
 *      and transfer. This function formats up a suitable buffer in the
 *      ifx_dev->tx_buffer
 *
 *      FIXME: performance - should we wake the tty when the queue is half
 *                           empty ?
 */
static int ifx_spi_prepare_tx_buffer(struct ifx_spi_device *ifx_dev)
{
        int temp_count;
        int queue_length;
        int tx_count;
        unsigned char *tx_buffer;

        tx_buffer = ifx_dev->tx_buffer;

        /* make room for required SPI header */
        tx_buffer += IFX_SPI_HEADER_OVERHEAD;
        tx_count = IFX_SPI_HEADER_OVERHEAD;

        /* clear to signal no more data if this turns out to be the
         * last buffer sent in a sequence */
        ifx_dev->spi_more = 0;

        /* if modem cts is set, just send empty buffer */
        if (!ifx_dev->spi_slave_cts) {
                /* see if there's tx data */
                queue_length = kfifo_len(&ifx_dev->tx_fifo);
                if (queue_length != 0) {
                        /* data to mux -- see if there's room for it */
                        temp_count = min(queue_length, IFX_SPI_PAYLOAD_SIZE);
                        temp_count = kfifo_out_locked(&ifx_dev->tx_fifo,
                                        tx_buffer, temp_count,
                                        &ifx_dev->fifo_lock);

                        /* update buffer pointer and data count in message */
                        tx_buffer += temp_count;
                        tx_count += temp_count;
                        if (temp_count == queue_length)
                                /* poke port to get more data */
                                tty_port_tty_wakeup(&ifx_dev->tty_port);
                        else /* more data in port, use next SPI message */
                                ifx_dev->spi_more = 1;
                }
        }
        /* have data and info for header -- set up SPI header in buffer */
        /* spi header needs payload size, not entire buffer size */
        ifx_spi_setup_spi_header(ifx_dev->tx_buffer,
                                        tx_count-IFX_SPI_HEADER_OVERHEAD,
                                        ifx_dev->spi_more);
        /* swap actual data in the buffer */
        ifx_dev->swap_buf((ifx_dev->tx_buffer), tx_count,
                &ifx_dev->tx_buffer[IFX_SPI_TRANSFER_SIZE]);
        return tx_count;
}

/**
 *      ifx_spi_write           -       line discipline write
 *      @tty: our tty device
 *      @buf: pointer to buffer to write (kernel space)
 *      @count: size of buffer
 *
 *      Write the characters we have been given into the FIFO. If the device
 *      is not active then activate it, when the SRDY line is asserted back
 *      this will commence I/O
 */
static int ifx_spi_write(struct tty_struct *tty, const unsigned char *buf,
                         int count)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;
        unsigned char *tmp_buf = (unsigned char *)buf;
        unsigned long flags;
        bool is_fifo_empty;
        int tx_count;

        spin_lock_irqsave(&ifx_dev->fifo_lock, flags);
        is_fifo_empty = kfifo_is_empty(&ifx_dev->tx_fifo);
        tx_count = kfifo_in(&ifx_dev->tx_fifo, tmp_buf, count);
        spin_unlock_irqrestore(&ifx_dev->fifo_lock, flags);
        if (is_fifo_empty)
                mrdy_assert(ifx_dev);

        return tx_count;
}

/**
 *      ifx_spi_chars_in_buffer -       line discipline helper
 *      @tty: our tty device
 *
 *      Report how much data we can accept before we drop bytes. As we use
 *      a simple FIFO this is nice and easy.
 */
static int ifx_spi_write_room(struct tty_struct *tty)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;
        return IFX_SPI_FIFO_SIZE - kfifo_len(&ifx_dev->tx_fifo);
}

/**
 *      ifx_spi_chars_in_buffer -       line discipline helper
 *      @tty: our tty device
 *
 *      Report how many characters we have buffered. In our case this is the
 *      number of bytes sitting in our transmit FIFO.
 */
static int ifx_spi_chars_in_buffer(struct tty_struct *tty)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;
        return kfifo_len(&ifx_dev->tx_fifo);
}

/**
 *      ifx_port_hangup
 *      @port: our tty port
 *
 *      tty port hang up. Called when tty_hangup processing is invoked either
 *      by loss of carrier, or by software (eg vhangup). Serialized against
 *      activate/shutdown by the tty layer.
 */
static void ifx_spi_hangup(struct tty_struct *tty)
{
        struct ifx_spi_device *ifx_dev = tty->driver_data;
        tty_port_hangup(&ifx_dev->tty_port);
}

/**
 *      ifx_port_activate
 *      @port: our tty port
 *
 *      tty port activate method - called for first open. Serialized
 *      with hangup and shutdown by the tty layer.
 */
static int ifx_port_activate(struct tty_port *port, struct tty_struct *tty)
{
        struct ifx_spi_device *ifx_dev =
                container_of(port, struct ifx_spi_device, tty_port);

        /* clear any old data; can't do this in 'close' */
        kfifo_reset(&ifx_dev->tx_fifo);

        /* clear any flag which may be set in port shutdown procedure */
        clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags);
        clear_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags);

        /* put port data into this tty */
        tty->driver_data = ifx_dev;

        /* allows flip string push from int context */
        port->low_latency = 1;

        /* set flag to allows data transfer */
        set_bit(IFX_SPI_STATE_IO_AVAILABLE, &ifx_dev->flags);

        return 0;
}

/**
 *      ifx_port_shutdown
 *      @port: our tty port
 *
 *      tty port shutdown method - called for last port close. Serialized
 *      with hangup and activate by the tty layer.
 */
static void ifx_port_shutdown(struct tty_port *port)
{
        struct ifx_spi_device *ifx_dev =
                container_of(port, struct ifx_spi_device, tty_port);

        clear_bit(IFX_SPI_STATE_IO_AVAILABLE, &ifx_dev->flags);
        mrdy_set_low(ifx_dev);
        del_timer(&ifx_dev->spi_timer);
        clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
        tasklet_kill(&ifx_dev->io_work_tasklet);
}

static const struct tty_port_operations ifx_tty_port_ops = {
        .activate = ifx_port_activate,
        .shutdown = ifx_port_shutdown,
};

static const struct tty_operations ifx_spi_serial_ops = {
        .open = ifx_spi_open,
        .close = ifx_spi_close,
        .write = ifx_spi_write,
        .hangup = ifx_spi_hangup,
        .write_room = ifx_spi_write_room,
        .chars_in_buffer = ifx_spi_chars_in_buffer,
        .tiocmget = ifx_spi_tiocmget,
        .tiocmset = ifx_spi_tiocmset,
};

/**
 *      ifx_spi_insert_fip_string       -       queue received data
 *      @ifx_ser: our SPI device
 *      @chars: buffer we have received
 *      @size: number of chars reeived
 *
 *      Queue bytes to the tty assuming the tty side is currently open. If
 *      not the discard the data.
 */
static void ifx_spi_insert_flip_string(struct ifx_spi_device *ifx_dev,
                                    unsigned char *chars, size_t size)
{
        tty_insert_flip_string(&ifx_dev->tty_port, chars, size);
        tty_flip_buffer_push(&ifx_dev->tty_port);
}

/**
 *      ifx_spi_complete        -       SPI transfer completed
 *      @ctx: our SPI device
 *
 *      An SPI transfer has completed. Process any received data and kick off
 *      any further transmits we can commence.
 */
static void ifx_spi_complete(void *ctx)
{
        struct ifx_spi_device *ifx_dev = ctx;
        int length;
        int actual_length;
        unsigned char more;
        unsigned char cts;
        int local_write_pending = 0;
        int queue_length;
        int srdy;
        int decode_result;

        mrdy_set_low(ifx_dev);

        if (!ifx_dev->spi_msg.status) {
                /* check header validity, get comm flags */
                ifx_dev->swap_buf(ifx_dev->rx_buffer, IFX_SPI_HEADER_OVERHEAD,
                        &ifx_dev->rx_buffer[IFX_SPI_HEADER_OVERHEAD]);
                decode_result = ifx_spi_decode_spi_header(ifx_dev->rx_buffer,
                                &length, &more, &cts);
                if (decode_result == IFX_SPI_HEADER_0) {
                        dev_dbg(&ifx_dev->spi_dev->dev,
                                "ignore input: invalid header 0");
                        ifx_dev->spi_slave_cts = 0;
                        goto complete_exit;
                } else if (decode_result == IFX_SPI_HEADER_F) {
                        dev_dbg(&ifx_dev->spi_dev->dev,
                                "ignore input: invalid header F");
                        goto complete_exit;
                }

                ifx_dev->spi_slave_cts = cts;

                actual_length = min((unsigned int)length,
                                        ifx_dev->spi_msg.actual_length);
                ifx_dev->swap_buf(
                        (ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD),
                         actual_length,
                         &ifx_dev->rx_buffer[IFX_SPI_TRANSFER_SIZE]);
                ifx_spi_insert_flip_string(
                        ifx_dev,
                        ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD,
                        (size_t)actual_length);
        } else {
                dev_dbg(&ifx_dev->spi_dev->dev, "SPI transfer error %d",
                       ifx_dev->spi_msg.status);
        }

complete_exit:
        if (ifx_dev->write_pending) {
                ifx_dev->write_pending = 0;
                local_write_pending = 1;
        }

        clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &(ifx_dev->flags));

        queue_length = kfifo_len(&ifx_dev->tx_fifo);
        srdy = gpio_get_value(ifx_dev->gpio.srdy);
        if (!srdy)
                ifx_spi_power_state_clear(ifx_dev, IFX_SPI_POWER_SRDY);

        /* schedule output if there is more to do */
        if (test_and_clear_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags))
                tasklet_schedule(&ifx_dev->io_work_tasklet);
        else {
                if (more || ifx_dev->spi_more || queue_length > 0 ||
                        local_write_pending) {
                        if (ifx_dev->spi_slave_cts) {
                                if (more)
                                        mrdy_assert(ifx_dev);
                        } else
                                mrdy_assert(ifx_dev);
                } else {
                        /*
                         * poke line discipline driver if any for more data
                         * may or may not get more data to write
                         * for now, say not busy
                         */
                        ifx_spi_power_state_clear(ifx_dev,
                                                  IFX_SPI_POWER_DATA_PENDING);
                        tty_port_tty_wakeup(&ifx_dev->tty_port);
                }
        }
}

/**
 *      ifx_spio_io             -       I/O tasklet
 *      @data: our SPI device
 *
 *      Queue data for transmission if possible and then kick off the
 *      transfer.
 */
static void ifx_spi_io(unsigned long data)
{
        int retval;
        struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *) data;

        if (!test_and_set_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags) &&
                test_bit(IFX_SPI_STATE_IO_AVAILABLE, &ifx_dev->flags)) {
                if (ifx_dev->gpio.unack_srdy_int_nb > 0)
                        ifx_dev->gpio.unack_srdy_int_nb--;

                ifx_spi_prepare_tx_buffer(ifx_dev);

                spi_message_init(&ifx_dev->spi_msg);
                INIT_LIST_HEAD(&ifx_dev->spi_msg.queue);

                ifx_dev->spi_msg.context = ifx_dev;
                ifx_dev->spi_msg.complete = ifx_spi_complete;

                /* set up our spi transfer */
                /* note len is BYTES, not transfers */
                ifx_dev->spi_xfer.len = IFX_SPI_TRANSFER_SIZE;
                ifx_dev->spi_xfer.cs_change = 0;
                ifx_dev->spi_xfer.speed_hz = ifx_dev->spi_dev->max_speed_hz;
                /* ifx_dev->spi_xfer.speed_hz = 390625; */
                ifx_dev->spi_xfer.bits_per_word =
                        ifx_dev->spi_dev->bits_per_word;

                ifx_dev->spi_xfer.tx_buf = ifx_dev->tx_buffer;
                ifx_dev->spi_xfer.rx_buf = ifx_dev->rx_buffer;

                /*
                 * setup dma pointers
                 */
                if (ifx_dev->use_dma) {
                        ifx_dev->spi_msg.is_dma_mapped = 1;
                        ifx_dev->tx_dma = ifx_dev->tx_bus;
                        ifx_dev->rx_dma = ifx_dev->rx_bus;
                        ifx_dev->spi_xfer.tx_dma = ifx_dev->tx_dma;
                        ifx_dev->spi_xfer.rx_dma = ifx_dev->rx_dma;
                } else {
                        ifx_dev->spi_msg.is_dma_mapped = 0;
                        ifx_dev->tx_dma = (dma_addr_t)0;
                        ifx_dev->rx_dma = (dma_addr_t)0;
                        ifx_dev->spi_xfer.tx_dma = (dma_addr_t)0;
                        ifx_dev->spi_xfer.rx_dma = (dma_addr_t)0;
                }

                spi_message_add_tail(&ifx_dev->spi_xfer, &ifx_dev->spi_msg);

                /* Assert MRDY. This may have already been done by the write
                 * routine.
                 */
                mrdy_assert(ifx_dev);

                retval = spi_async(ifx_dev->spi_dev, &ifx_dev->spi_msg);
                if (retval) {
                        clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS,
                                  &ifx_dev->flags);
                        tasklet_schedule(&ifx_dev->io_work_tasklet);
                        return;
                }
        } else
                ifx_dev->write_pending = 1;
}

/**
 *      ifx_spi_free_port       -       free up the tty side
 *      @ifx_dev: IFX device going away
 *
 *      Unregister and free up a port when the device goes away
 */
static void ifx_spi_free_port(struct ifx_spi_device *ifx_dev)
{
        if (ifx_dev->tty_dev)
                tty_unregister_device(tty_drv, ifx_dev->minor);
        tty_port_destroy(&ifx_dev->tty_port);
        kfifo_free(&ifx_dev->tx_fifo);
}

/**
 *      ifx_spi_create_port     -       create a new port
 *      @ifx_dev: our spi device
 *
 *      Allocate and initialise the tty port that goes with this interface
 *      and add it to the tty layer so that it can be opened.
 */
static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev)
{
        int ret = 0;
        struct tty_port *pport = &ifx_dev->tty_port;

        spin_lock_init(&ifx_dev->fifo_lock);
        lockdep_set_class_and_subclass(&ifx_dev->fifo_lock,
                &ifx_spi_key, 0);

        if (kfifo_alloc(&ifx_dev->tx_fifo, IFX_SPI_FIFO_SIZE, GFP_KERNEL)) {
                ret = -ENOMEM;
                goto error_ret;
        }

        tty_port_init(pport);
        pport->ops = &ifx_tty_port_ops;
        ifx_dev->minor = IFX_SPI_TTY_ID;
        ifx_dev->tty_dev = tty_port_register_device(pport, tty_drv,
                        ifx_dev->minor, &ifx_dev->spi_dev->dev);
        if (IS_ERR(ifx_dev->tty_dev)) {
                dev_dbg(&ifx_dev->spi_dev->dev,
                        "%s: registering tty device failed", __func__);
                ret = PTR_ERR(ifx_dev->tty_dev);
                goto error_port;
        }
        return 0;

error_port:
        tty_port_destroy(pport);
error_ret:
        ifx_spi_free_port(ifx_dev);
        return ret;
}

/**
 *      ifx_spi_handle_srdy             -       handle SRDY
 *      @ifx_dev: device asserting SRDY
 *
 *      Check our device state and see what we need to kick off when SRDY
 *      is asserted. This usually means killing the timer and firing off the
 *      I/O processing.
 */
static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev)
{
        if (test_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags)) {
                del_timer(&ifx_dev->spi_timer);
                clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
        }

        ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_SRDY);

        if (!test_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags))
                tasklet_schedule(&ifx_dev->io_work_tasklet);
        else
                set_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags);
}

/**
 *      ifx_spi_srdy_interrupt  -       SRDY asserted
 *      @irq: our IRQ number
 *      @dev: our ifx device
 *
 *      The modem asserted SRDY. Handle the srdy event
 */
static irqreturn_t ifx_spi_srdy_interrupt(int irq, void *dev)
{
        struct ifx_spi_device *ifx_dev = dev;
        ifx_dev->gpio.unack_srdy_int_nb++;
        ifx_spi_handle_srdy(ifx_dev);
        return IRQ_HANDLED;
}

/**
 *      ifx_spi_reset_interrupt -       Modem has changed reset state
 *      @irq: interrupt number
 *      @dev: our device pointer
 *
 *      The modem has either entered or left reset state. Check the GPIO
 *      line to see which.
 *
 *      FIXME: review locking on MR_INPROGRESS versus
 *      parallel unsolicited reset/solicited reset
 */
static irqreturn_t ifx_spi_reset_interrupt(int irq, void *dev)
{
        struct ifx_spi_device *ifx_dev = dev;
        int val = gpio_get_value(ifx_dev->gpio.reset_out);
        int solreset = test_bit(MR_START, &ifx_dev->mdm_reset_state);

        if (val == 0) {
                /* entered reset */
                set_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
                if (!solreset) {
                        /* unsolicited reset  */
                        tty_port_tty_hangup(&ifx_dev->tty_port, false);
                }
        } else {
                /* exited reset */
                clear_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
                if (solreset) {
                        set_bit(MR_COMPLETE, &ifx_dev->mdm_reset_state);
                        wake_up(&ifx_dev->mdm_reset_wait);
                }
        }
        return IRQ_HANDLED;
}

/**
 *      ifx_spi_free_device - free device
 *      @ifx_dev: device to free
 *
 *      Free the IFX device
 */
static void ifx_spi_free_device(struct ifx_spi_device *ifx_dev)
{
        ifx_spi_free_port(ifx_dev);
        dma_free_coherent(&ifx_dev->spi_dev->dev,
                                IFX_SPI_TRANSFER_SIZE,
                                ifx_dev->tx_buffer,
                                ifx_dev->tx_bus);
        dma_free_coherent(&ifx_dev->spi_dev->dev,
                                IFX_SPI_TRANSFER_SIZE,
                                ifx_dev->rx_buffer,
                                ifx_dev->rx_bus);
}

/**
 *      ifx_spi_reset   -       reset modem
 *      @ifx_dev: modem to reset
 *
 *      Perform a reset on the modem
 */
static int ifx_spi_reset(struct ifx_spi_device *ifx_dev)
{
        int ret;
        /*
         * set up modem power, reset
         *
         * delays are required on some platforms for the modem
         * to reset properly
         */
        set_bit(MR_START, &ifx_dev->mdm_reset_state);
        gpio_set_value(ifx_dev->gpio.po, 0);
        gpio_set_value(ifx_dev->gpio.reset, 0);
        msleep(25);
        gpio_set_value(ifx_dev->gpio.reset, 1);
        msleep(1);
        gpio_set_value(ifx_dev->gpio.po, 1);
        msleep(1);
        gpio_set_value(ifx_dev->gpio.po, 0);
        ret = wait_event_timeout(ifx_dev->mdm_reset_wait,
                                 test_bit(MR_COMPLETE,
                                          &ifx_dev->mdm_reset_state),
                                 IFX_RESET_TIMEOUT);
        if (!ret)
                dev_warn(&ifx_dev->spi_dev->dev, "Modem reset timeout: (state:%lx)",
                         ifx_dev->mdm_reset_state);

        ifx_dev->mdm_reset_state = 0;
        return ret;
}

/**
 *      ifx_spi_spi_probe       -       probe callback
 *      @spi: our possible matching SPI device
 *
 *      Probe for a 6x60 modem on SPI bus. Perform any needed device and
 *      GPIO setup.
 *
 *      FIXME:
 *      -       Support for multiple devices
 *      -       Split out MID specific GPIO handling eventually
 */

static int ifx_spi_spi_probe(struct spi_device *spi)
{

        int ret;
        int srdy;
        struct ifx_modem_platform_data *pl_data;
        struct ifx_spi_device *ifx_dev;

        if (saved_ifx_dev) {
                dev_dbg(&spi->dev, "ignoring subsequent detection");
                return -ENODEV;
        }

        pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data;
        if (!pl_data) {
                dev_err(&spi->dev, "missing platform data!");
                return -ENODEV;
        }

        /* initialize structure to hold our device variables */
        ifx_dev = kzalloc(sizeof(struct ifx_spi_device), GFP_KERNEL);
        if (!ifx_dev) {
                dev_err(&spi->dev, "spi device allocation failed");
                return -ENOMEM;
        }
        saved_ifx_dev = ifx_dev;
        ifx_dev->spi_dev = spi;
        clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags);
        spin_lock_init(&ifx_dev->write_lock);
        spin_lock_init(&ifx_dev->power_lock);
        ifx_dev->power_status = 0;
        init_timer(&ifx_dev->spi_timer);
        ifx_dev->spi_timer.function = ifx_spi_timeout;
        ifx_dev->spi_timer.data = (unsigned long)ifx_dev;
        ifx_dev->modem = pl_data->modem_type;
        ifx_dev->use_dma = pl_data->use_dma;
        ifx_dev->max_hz = pl_data->max_hz;
        /* initialize spi mode, etc */
        spi->max_speed_hz = ifx_dev->max_hz;
        spi->mode = IFX_SPI_MODE | (SPI_LOOP & spi->mode);
        spi->bits_per_word = spi_bpw;
        ret = spi_setup(spi);
        if (ret) {
                dev_err(&spi->dev, "SPI setup wasn't successful %d", ret);
                return -ENODEV;
        }

        /* init swap_buf function according to word width configuration */
        if (spi->bits_per_word == 32)
                ifx_dev->swap_buf = swap_buf_32;
        else if (spi->bits_per_word == 16)
                ifx_dev->swap_buf = swap_buf_16;
        else
                ifx_dev->swap_buf = swap_buf_8;

        /* ensure SPI protocol flags are initialized to enable transfer */
        ifx_dev->spi_more = 0;
        ifx_dev->spi_slave_cts = 0;

        /*initialize transfer and dma buffers */
        ifx_dev->tx_buffer = dma_alloc_coherent(ifx_dev->spi_dev->dev.parent,
                                IFX_SPI_TRANSFER_SIZE,
                                &ifx_dev->tx_bus,
                                GFP_KERNEL);
        if (!ifx_dev->tx_buffer) {
                dev_err(&spi->dev, "DMA-TX buffer allocation failed");
                ret = -ENOMEM;
                goto error_ret;
        }
        ifx_dev->rx_buffer = dma_alloc_coherent(ifx_dev->spi_dev->dev.parent,
                                IFX_SPI_TRANSFER_SIZE,
                                &ifx_dev->rx_bus,
                                GFP_KERNEL);
        if (!ifx_dev->rx_buffer) {
                dev_err(&spi->dev, "DMA-RX buffer allocation failed");
                ret = -ENOMEM;
                goto error_ret;
        }

        /* initialize waitq for modem reset */
        init_waitqueue_head(&ifx_dev->mdm_reset_wait);

        spi_set_drvdata(spi, ifx_dev);
        tasklet_init(&ifx_dev->io_work_tasklet, ifx_spi_io,
                                                (unsigned long)ifx_dev);

        set_bit(IFX_SPI_STATE_PRESENT, &ifx_dev->flags);

        /* create our tty port */
        ret = ifx_spi_create_port(ifx_dev);
        if (ret != 0) {
                dev_err(&spi->dev, "create default tty port failed");
                goto error_ret;
        }

        ifx_dev->gpio.reset = pl_data->rst_pmu;
        ifx_dev->gpio.po = pl_data->pwr_on;
        ifx_dev->gpio.mrdy = pl_data->mrdy;
        ifx_dev->gpio.srdy = pl_data->srdy;
        ifx_dev->gpio.reset_out = pl_data->rst_out;

        dev_info(&spi->dev, "gpios %d, %d, %d, %d, %d",
                 ifx_dev->gpio.reset, ifx_dev->gpio.po, ifx_dev->gpio.mrdy,
                 ifx_dev->gpio.srdy, ifx_dev->gpio.reset_out);

        /* Configure gpios */
        ret = gpio_request(ifx_dev->gpio.reset, "ifxModem");
        if (ret < 0) {
                dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET)",
                        ifx_dev->gpio.reset);
                goto error_ret;
        }
        ret += gpio_direction_output(ifx_dev->gpio.reset, 0);
        ret += gpio_export(ifx_dev->gpio.reset, 1);
        if (ret) {
                dev_err(&spi->dev, "Unable to configure GPIO%d (RESET)",
                        ifx_dev->gpio.reset);
                ret = -EBUSY;
                goto error_ret2;
        }

        ret = gpio_request(ifx_dev->gpio.po, "ifxModem");
        ret += gpio_direction_output(ifx_dev->gpio.po, 0);
        ret += gpio_export(ifx_dev->gpio.po, 1);
        if (ret) {
                dev_err(&spi->dev, "Unable to configure GPIO%d (ON)",
                        ifx_dev->gpio.po);
                ret = -EBUSY;
                goto error_ret3;
        }

        ret = gpio_request(ifx_dev->gpio.mrdy, "ifxModem");
        if (ret < 0) {
                dev_err(&spi->dev, "Unable to allocate GPIO%d (MRDY)",
                        ifx_dev->gpio.mrdy);
                goto error_ret3;
        }
        ret += gpio_export(ifx_dev->gpio.mrdy, 1);
        ret += gpio_direction_output(ifx_dev->gpio.mrdy, 0);
        if (ret) {
                dev_err(&spi->dev, "Unable to configure GPIO%d (MRDY)",
                        ifx_dev->gpio.mrdy);
                ret = -EBUSY;
                goto error_ret4;
        }

        ret = gpio_request(ifx_dev->gpio.srdy, "ifxModem");
        if (ret < 0) {
                dev_err(&spi->dev, "Unable to allocate GPIO%d (SRDY)",
                        ifx_dev->gpio.srdy);
                ret = -EBUSY;
                goto error_ret4;
        }
        ret += gpio_export(ifx_dev->gpio.srdy, 1);
        ret += gpio_direction_input(ifx_dev->gpio.srdy);
        if (ret) {
                dev_err(&spi->dev, "Unable to configure GPIO%d (SRDY)",
                        ifx_dev->gpio.srdy);
                ret = -EBUSY;
                goto error_ret5;
        }

        ret = gpio_request(ifx_dev->gpio.reset_out, "ifxModem");
        if (ret < 0) {
                dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET_OUT)",
                        ifx_dev->gpio.reset_out);
                goto error_ret5;
        }
        ret += gpio_export(ifx_dev->gpio.reset_out, 1);
        ret += gpio_direction_input(ifx_dev->gpio.reset_out);
        if (ret) {
                dev_err(&spi->dev, "Unable to configure GPIO%d (RESET_OUT)",
                        ifx_dev->gpio.reset_out);
                ret = -EBUSY;
                goto error_ret6;
        }

        ret = request_irq(gpio_to_irq(ifx_dev->gpio.reset_out),
                          ifx_spi_reset_interrupt,
                          IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING, DRVNAME,
                (void *)ifx_dev);
        if (ret) {
                dev_err(&spi->dev, "Unable to get irq %x\n",
                        gpio_to_irq(ifx_dev->gpio.reset_out));
                goto error_ret6;
        }

        ret = ifx_spi_reset(ifx_dev);

        ret = request_irq(gpio_to_irq(ifx_dev->gpio.srdy),
                          ifx_spi_srdy_interrupt,
                          IRQF_TRIGGER_RISING, DRVNAME,
                          (void *)ifx_dev);
        if (ret) {
                dev_err(&spi->dev, "Unable to get irq %x",
                        gpio_to_irq(ifx_dev->gpio.srdy));
                goto error_ret7;
        }

        /* set pm runtime power state and register with power system */
        pm_runtime_set_active(&spi->dev);
        pm_runtime_enable(&spi->dev);

        /* handle case that modem is already signaling SRDY */
        /* no outgoing tty open at this point, this just satisfies the
         * modem's read and should reset communication properly
         */
        srdy = gpio_get_value(ifx_dev->gpio.srdy);

        if (srdy) {
                mrdy_assert(ifx_dev);
                ifx_spi_handle_srdy(ifx_dev);
        } else
                mrdy_set_low(ifx_dev);
        return 0;

error_ret7:
        free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
error_ret6:
        gpio_free(ifx_dev->gpio.srdy);
error_ret5:
        gpio_free(ifx_dev->gpio.mrdy);
error_ret4:
        gpio_free(ifx_dev->gpio.reset);
error_ret3:
        gpio_free(ifx_dev->gpio.po);
error_ret2:
        gpio_free(ifx_dev->gpio.reset_out);
error_ret:
        ifx_spi_free_device(ifx_dev);
        saved_ifx_dev = NULL;
        return ret;
}

/**
 *      ifx_spi_spi_remove      -       SPI device was removed
 *      @spi: SPI device
 *
 *      FIXME: We should be shutting the device down here not in
 *      the module unload path.
 */

static int ifx_spi_spi_remove(struct spi_device *spi)
{
        struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);
        /* stop activity */
        tasklet_kill(&ifx_dev->io_work_tasklet);
        /* free irq */
        free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
        free_irq(gpio_to_irq(ifx_dev->gpio.srdy), (void *)ifx_dev);

        gpio_free(ifx_dev->gpio.srdy);
        gpio_free(ifx_dev->gpio.mrdy);
        gpio_free(ifx_dev->gpio.reset);
        gpio_free(ifx_dev->gpio.po);
        gpio_free(ifx_dev->gpio.reset_out);

        /* free allocations */
        ifx_spi_free_device(ifx_dev);

        saved_ifx_dev = NULL;
        return 0;
}

/**
 *      ifx_spi_spi_shutdown    -       called on SPI shutdown
 *      @spi: SPI device
 *
 *      No action needs to be taken here
 */

static void ifx_spi_spi_shutdown(struct spi_device *spi)
{
        struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);

        ifx_modem_power_off(ifx_dev);
}

/*
 * various suspends and resumes have nothing to do
 * no hardware to save state for
 */

/**
 *      ifx_spi_pm_suspend      -       suspend modem on system suspend
 *      @dev: device being suspended
 *
 *      Suspend the modem. No action needed on Intel MID platforms, may
 *      need extending for other systems.
 */
static int ifx_spi_pm_suspend(struct device *dev)
{
        return 0;
}

/**
 *      ifx_spi_pm_resume       -       resume modem on system resume
 *      @dev: device being suspended
 *
 *      Allow the modem to resume. No action needed.
 *
 *      FIXME: do we need to reset anything here ?
 */
static int ifx_spi_pm_resume(struct device *dev)
{
        return 0;
}

/**
 *      ifx_spi_pm_runtime_resume       -       suspend modem
 *      @dev: device being suspended
 *
 *      Allow the modem to resume. No action needed.
 */
static int ifx_spi_pm_runtime_resume(struct device *dev)
{
        return 0;
}

/**
 *      ifx_spi_pm_runtime_suspend      -       suspend modem
 *      @dev: device being suspended
 *
 *      Allow the modem to suspend and thus suspend to continue up the
 *      device tree.
 */
static int ifx_spi_pm_runtime_suspend(struct device *dev)
{
        return 0;
}

/**
 *      ifx_spi_pm_runtime_idle         -       check if modem idle
 *      @dev: our device
 *
 *      Check conditions and queue runtime suspend if idle.
 */
static int ifx_spi_pm_runtime_idle(struct device *dev)
{
        struct spi_device *spi = to_spi_device(dev);
        struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);

        if (!ifx_dev->power_status)
                pm_runtime_suspend(dev);

        return 0;
}

static const struct dev_pm_ops ifx_spi_pm = {
        .resume = ifx_spi_pm_resume,
        .suspend = ifx_spi_pm_suspend,
        .runtime_resume = ifx_spi_pm_runtime_resume,
        .runtime_suspend = ifx_spi_pm_runtime_suspend,
        .runtime_idle = ifx_spi_pm_runtime_idle
};

static const struct spi_device_id ifx_id_table[] = {
        {"ifx6160", 0},
        {"ifx6260", 0},
        { }
};
MODULE_DEVICE_TABLE(spi, ifx_id_table);

/* spi operations */
static struct spi_driver ifx_spi_driver = {
        .driver = {
                .name = DRVNAME,
                .pm = &ifx_spi_pm,
                .owner = THIS_MODULE},
        .probe = ifx_spi_spi_probe,
        .shutdown = ifx_spi_spi_shutdown,
        .remove = ifx_spi_spi_remove,
        .id_table = ifx_id_table
};

/**
 *      ifx_spi_exit    -       module exit
 *
 *      Unload the module.
 */

static void __exit ifx_spi_exit(void)
{
        /* unregister */
        tty_unregister_driver(tty_drv);
        put_tty_driver(tty_drv);
        spi_unregister_driver((void *)&ifx_spi_driver);
        unregister_reboot_notifier(&ifx_modem_reboot_notifier_block);
}

/**
 *      ifx_spi_init            -       module entry point
 *
 *      Initialise the SPI and tty interfaces for the IFX SPI driver
 *      We need to initialize upper-edge spi driver after the tty
 *      driver because otherwise the spi probe will race
 */

static int __init ifx_spi_init(void)
{
        int result;

        tty_drv = alloc_tty_driver(1);
        if (!tty_drv) {
                pr_err("%s: alloc_tty_driver failed", DRVNAME);
                return -ENOMEM;
        }

        tty_drv->driver_name = DRVNAME;
        tty_drv->name = TTYNAME;
        tty_drv->minor_start = IFX_SPI_TTY_ID;
        tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
        tty_drv->subtype = SERIAL_TYPE_NORMAL;
        tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
        tty_drv->init_termios = tty_std_termios;

        tty_set_operations(tty_drv, &ifx_spi_serial_ops);

        result = tty_register_driver(tty_drv);
        if (result) {
                pr_err("%s: tty_register_driver failed(%d)",
                        DRVNAME, result);
                goto err_free_tty;
        }

        result = spi_register_driver((void *)&ifx_spi_driver);
        if (result) {
                pr_err("%s: spi_register_driver failed(%d)",
                        DRVNAME, result);
                goto err_unreg_tty;
        }

        result = register_reboot_notifier(&ifx_modem_reboot_notifier_block);
        if (result) {
                pr_err("%s: register ifx modem reboot notifier failed(%d)",
                        DRVNAME, result);
                goto err_unreg_spi;
        }

        return 0;
err_unreg_spi:
        spi_unregister_driver((void *)&ifx_spi_driver);
err_unreg_tty:
        tty_unregister_driver(tty_drv);
err_free_tty:
        put_tty_driver(tty_drv);

        return result;
}

module_init(ifx_spi_init);
module_exit(ifx_spi_exit);

MODULE_AUTHOR("Intel");
MODULE_DESCRIPTION("IFX6x60 spi driver");
MODULE_LICENSE("GPL");
MODULE_INFO(Version, "0.1-IFX6x60");