/*
 * V4L2 SoC Camera driver for OMAP1 Camera Interface
 *
 * Copyright (C) 2010, Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
 *
 * Based on V4L2 Driver for i.MXL/i.MXL camera (CSI) host
 * Copyright (C) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
 * Copyright (C) 2009, Darius Augulis <augulis.darius@gmail.com>
 *
 * Based on PXA SoC camera driver
 * Copyright (C) 2006, Sascha Hauer, Pengutronix
 * Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de>
 *
 * Hardware specific bits initialy based on former work by Matt Callow
 * drivers/media/platform/omap/omap1510cam.c
 * Copyright (C) 2006 Matt Callow
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */


#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>

#include <media/omap1_camera.h>
#include <media/soc_camera.h>
#include <media/soc_mediabus.h>
#include <media/videobuf-dma-contig.h>
#include <media/videobuf-dma-sg.h>

#include <linux/omap-dma.h>


#define DRIVER_NAME             "omap1-camera"
#define DRIVER_VERSION          "0.0.2"

#define OMAP_DMA_CAMERA_IF_RX           20

/*
 * ---------------------------------------------------------------------------
 *  OMAP1 Camera Interface registers
 * ---------------------------------------------------------------------------
 */

#define REG_CTRLCLOCK           0x00
#define REG_IT_STATUS           0x04
#define REG_MODE                0x08
#define REG_STATUS              0x0C
#define REG_CAMDATA             0x10
#define REG_GPIO                0x14
#define REG_PEAK_COUNTER        0x18

/* CTRLCLOCK bit shifts */
#define LCLK_EN                 BIT(7)
#define DPLL_EN                 BIT(6)
#define MCLK_EN                 BIT(5)
#define CAMEXCLK_EN             BIT(4)
#define POLCLK                  BIT(3)
#define FOSCMOD_SHIFT           0
#define FOSCMOD_MASK            (0x7 << FOSCMOD_SHIFT)
#define FOSCMOD_12MHz           0x0
#define FOSCMOD_6MHz            0x2
#define FOSCMOD_9_6MHz          0x4
#define FOSCMOD_24MHz           0x5
#define FOSCMOD_8MHz            0x6

/* IT_STATUS bit shifts */
#define DATA_TRANSFER           BIT(5)
#define FIFO_FULL               BIT(4)
#define H_DOWN                  BIT(3)
#define H_UP                    BIT(2)
#define V_DOWN                  BIT(1)
#define V_UP                    BIT(0)

/* MODE bit shifts */
#define RAZ_FIFO                BIT(18)
#define EN_FIFO_FULL            BIT(17)
#define EN_NIRQ                 BIT(16)
#define THRESHOLD_SHIFT         9
#define THRESHOLD_MASK          (0x7f << THRESHOLD_SHIFT)
#define DMA                     BIT(8)
#define EN_H_DOWN               BIT(7)
#define EN_H_UP                 BIT(6)
#define EN_V_DOWN               BIT(5)
#define EN_V_UP                 BIT(4)
#define ORDERCAMD               BIT(3)

#define IRQ_MASK                (EN_V_UP | EN_V_DOWN | EN_H_UP | EN_H_DOWN | \
                                 EN_NIRQ | EN_FIFO_FULL)

/* STATUS bit shifts */
#define HSTATUS                 BIT(1)
#define VSTATUS                 BIT(0)

/* GPIO bit shifts */
#define CAM_RST                 BIT(0)

/* end of OMAP1 Camera Interface registers */


#define SOCAM_BUS_FLAGS (V4L2_MBUS_MASTER | \
                        V4L2_MBUS_HSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_HIGH | \
                        V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING | \
                        V4L2_MBUS_DATA_ACTIVE_HIGH)


#define FIFO_SIZE               ((THRESHOLD_MASK >> THRESHOLD_SHIFT) + 1)
#define FIFO_SHIFT              __fls(FIFO_SIZE)

#define DMA_BURST_SHIFT         (1 + OMAP_DMA_DATA_BURST_4)
#define DMA_BURST_SIZE          (1 << DMA_BURST_SHIFT)

#define DMA_ELEMENT_SHIFT       OMAP_DMA_DATA_TYPE_S32
#define DMA_ELEMENT_SIZE        (1 << DMA_ELEMENT_SHIFT)

#define DMA_FRAME_SHIFT_CONTIG  (FIFO_SHIFT - 1)
#define DMA_FRAME_SHIFT_SG      DMA_BURST_SHIFT

#define DMA_FRAME_SHIFT(x)      ((x) == OMAP1_CAM_DMA_CONTIG ? \
                                                DMA_FRAME_SHIFT_CONTIG : \
                                                DMA_FRAME_SHIFT_SG)
#define DMA_FRAME_SIZE(x)       (1 << DMA_FRAME_SHIFT(x))
#define DMA_SYNC                OMAP_DMA_SYNC_FRAME
#define THRESHOLD_LEVEL         DMA_FRAME_SIZE


#define MAX_VIDEO_MEM           4       /* arbitrary video memory limit in MB */


/*
 * Structures
 */

/* buffer for one video frame */
struct omap1_cam_buf {
        struct videobuf_buffer          vb;
        enum v4l2_mbus_pixelcode        code;
        int                             inwork;
        struct scatterlist              *sgbuf;
        int                             sgcount;
        int                             bytes_left;
        enum videobuf_state             result;
};

struct omap1_cam_dev {
        struct soc_camera_host          soc_host;
        struct clk                      *clk;

        unsigned int                    irq;
        void __iomem                    *base;

        int                             dma_ch;

        struct omap1_cam_platform_data  *pdata;
        struct resource                 *res;
        unsigned long                   pflags;
        unsigned long                   camexclk;

        struct list_head                capture;

        /* lock used to protect videobuf */
        spinlock_t                      lock;

        /* Pointers to DMA buffers */
        struct omap1_cam_buf            *active;
        struct omap1_cam_buf            *ready;

        enum omap1_cam_vb_mode          vb_mode;
        int                             (*mmap_mapper)(struct videobuf_queue *q,
                                                struct videobuf_buffer *buf,
                                                struct vm_area_struct *vma);

        u32                             reg_cache[0];
};


static void cam_write(struct omap1_cam_dev *pcdev, u16 reg, u32 val)
{
        pcdev->reg_cache[reg / sizeof(u32)] = val;
        __raw_writel(val, pcdev->base + reg);
}

static u32 cam_read(struct omap1_cam_dev *pcdev, u16 reg, bool from_cache)
{
        return !from_cache ? __raw_readl(pcdev->base + reg) :
                        pcdev->reg_cache[reg / sizeof(u32)];
}

#define CAM_READ(pcdev, reg) \
                cam_read(pcdev, REG_##reg, false)
#define CAM_WRITE(pcdev, reg, val) \
                cam_write(pcdev, REG_##reg, val)
#define CAM_READ_CACHE(pcdev, reg) \
                cam_read(pcdev, REG_##reg, true)

/*
 *  Videobuf operations
 */
static int omap1_videobuf_setup(struct videobuf_queue *vq, unsigned int *count,
                unsigned int *size)
{
        struct soc_camera_device *icd = vq->priv_data;
        struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
        struct omap1_cam_dev *pcdev = ici->priv;

        *size = icd->sizeimage;

        if (!*count || *count < OMAP1_CAMERA_MIN_BUF_COUNT(pcdev->vb_mode))
                *count = OMAP1_CAMERA_MIN_BUF_COUNT(pcdev->vb_mode);

        if (*size * *count > MAX_VIDEO_MEM * 1024 * 1024)
                *count = (MAX_VIDEO_MEM * 1024 * 1024) / *size;

        dev_dbg(icd->parent,
                        "%s: count=%d, size=%d\n", __func__, *count, *size);

        return 0;
}

static void free_buffer(struct videobuf_queue *vq, struct omap1_cam_buf *buf,
                enum omap1_cam_vb_mode vb_mode)
{
        struct videobuf_buffer *vb = &buf->vb;

        BUG_ON(in_interrupt());

        videobuf_waiton(vq, vb, 0, 0);

        if (vb_mode == OMAP1_CAM_DMA_CONTIG) {
                videobuf_dma_contig_free(vq, vb);
        } else {
                struct soc_camera_device *icd = vq->priv_data;
                struct device *dev = icd->parent;
                struct videobuf_dmabuf *dma = videobuf_to_dma(vb);

                videobuf_dma_unmap(dev, dma);
                videobuf_dma_free(dma);
        }

        vb->state = VIDEOBUF_NEEDS_INIT;
}

static int omap1_videobuf_prepare(struct videobuf_queue *vq,
                struct videobuf_buffer *vb, enum v4l2_field field)
{
        struct soc_camera_device *icd = vq->priv_data;
        struct omap1_cam_buf *buf = container_of(vb, struct omap1_cam_buf, vb);
        struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
        struct omap1_cam_dev *pcdev = ici->priv;
        int ret;

        WARN_ON(!list_empty(&vb->queue));

        BUG_ON(NULL == icd->current_fmt);

        buf->inwork = 1;

        if (buf->code != icd->current_fmt->code || vb->field != field ||
                        vb->width  != icd->user_width ||
                        vb->height != icd->user_height) {
                buf->code  = icd->current_fmt->code;
                vb->width  = icd->user_width;
                vb->height = icd->user_height;
                vb->field  = field;
                vb->state  = VIDEOBUF_NEEDS_INIT;
        }

        vb->size = icd->sizeimage;

        if (vb->baddr && vb->bsize < vb->size) {
                ret = -EINVAL;
                goto out;
        }

        if (vb->state == VIDEOBUF_NEEDS_INIT) {
                ret = videobuf_iolock(vq, vb, NULL);
                if (ret)
                        goto fail;

                vb->state = VIDEOBUF_PREPARED;
        }
        buf->inwork = 0;

        return 0;
fail:
        free_buffer(vq, buf, pcdev->vb_mode);
out:
        buf->inwork = 0;
        return ret;
}

static void set_dma_dest_params(int dma_ch, struct omap1_cam_buf *buf,
                enum omap1_cam_vb_mode vb_mode)
{
        dma_addr_t dma_addr;
        unsigned int block_size;

        if (vb_mode == OMAP1_CAM_DMA_CONTIG) {
                dma_addr = videobuf_to_dma_contig(&buf->vb);
                block_size = buf->vb.size;
        } else {
                if (WARN_ON(!buf->sgbuf)) {
                        buf->result = VIDEOBUF_ERROR;
                        return;
                }
                dma_addr = sg_dma_address(buf->sgbuf);
                if (WARN_ON(!dma_addr)) {
                        buf->sgbuf = NULL;
                        buf->result = VIDEOBUF_ERROR;
                        return;
                }
                block_size = sg_dma_len(buf->sgbuf);
                if (WARN_ON(!block_size)) {
                        buf->sgbuf = NULL;
                        buf->result = VIDEOBUF_ERROR;
                        return;
                }
                if (unlikely(buf->bytes_left < block_size))
                        block_size = buf->bytes_left;
                if (WARN_ON(dma_addr & (DMA_FRAME_SIZE(vb_mode) *
                                DMA_ELEMENT_SIZE - 1))) {
                        dma_addr = ALIGN(dma_addr, DMA_FRAME_SIZE(vb_mode) *
                                        DMA_ELEMENT_SIZE);
                        block_size &= ~(DMA_FRAME_SIZE(vb_mode) *
                                        DMA_ELEMENT_SIZE - 1);
                }
                buf->bytes_left -= block_size;
                buf->sgcount++;
        }

        omap_set_dma_dest_params(dma_ch,
                OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, dma_addr, 0, 0);
        omap_set_dma_transfer_params(dma_ch,
                OMAP_DMA_DATA_TYPE_S32, DMA_FRAME_SIZE(vb_mode),
                block_size >> (DMA_FRAME_SHIFT(vb_mode) + DMA_ELEMENT_SHIFT),
                DMA_SYNC, 0, 0);
}

static struct omap1_cam_buf *prepare_next_vb(struct omap1_cam_dev *pcdev)
{
        struct omap1_cam_buf *buf;

        /*
         * If there is already a buffer pointed out by the pcdev->ready,
         * (re)use it, otherwise try to fetch and configure a new one.
         */
        buf = pcdev->ready;
        if (!buf) {
                if (list_empty(&pcdev->capture))
                        return buf;
                buf = list_entry(pcdev->capture.next,
                                struct omap1_cam_buf, vb.queue);
                buf->vb.state = VIDEOBUF_ACTIVE;
                pcdev->ready = buf;
                list_del_init(&buf->vb.queue);
        }

        if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                /*
                 * In CONTIG mode, we can safely enter next buffer parameters
                 * into the DMA programming register set after the DMA
                 * has already been activated on the previous buffer
                 */
                set_dma_dest_params(pcdev->dma_ch, buf, pcdev->vb_mode);
        } else {
                /*
                 * In SG mode, the above is not safe since there are probably
                 * a bunch of sgbufs from previous sglist still pending.
                 * Instead, mark the sglist fresh for the upcoming
                 * try_next_sgbuf().
                 */
                buf->sgbuf = NULL;
        }

        return buf;
}

static struct scatterlist *try_next_sgbuf(int dma_ch, struct omap1_cam_buf *buf)
{
        struct scatterlist *sgbuf;

        if (likely(buf->sgbuf)) {
                /* current sglist is active */
                if (unlikely(!buf->bytes_left)) {
                        /* indicate sglist complete */
                        sgbuf = NULL;
                } else {
                        /* process next sgbuf */
                        sgbuf = sg_next(buf->sgbuf);
                        if (WARN_ON(!sgbuf)) {
                                buf->result = VIDEOBUF_ERROR;
                        } else if (WARN_ON(!sg_dma_len(sgbuf))) {
                                sgbuf = NULL;
                                buf->result = VIDEOBUF_ERROR;
                        }
                }
                buf->sgbuf = sgbuf;
        } else {
                /* sglist is fresh, initialize it before using */
                struct videobuf_dmabuf *dma = videobuf_to_dma(&buf->vb);

                sgbuf = dma->sglist;
                if (!(WARN_ON(!sgbuf))) {
                        buf->sgbuf = sgbuf;
                        buf->sgcount = 0;
                        buf->bytes_left = buf->vb.size;
                        buf->result = VIDEOBUF_DONE;
                }
        }
        if (sgbuf)
                /*
                 * Put our next sgbuf parameters (address, size)
                 * into the DMA programming register set.
                 */
                set_dma_dest_params(dma_ch, buf, OMAP1_CAM_DMA_SG);

        return sgbuf;
}

static void start_capture(struct omap1_cam_dev *pcdev)
{
        struct omap1_cam_buf *buf = pcdev->active;
        u32 ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK);
        u32 mode = CAM_READ_CACHE(pcdev, MODE) & ~EN_V_DOWN;

        if (WARN_ON(!buf))
                return;

        /*
         * Enable start of frame interrupt, which we will use for activating
         * our end of frame watchdog when capture actually starts.
         */
        mode |= EN_V_UP;

        if (unlikely(ctrlclock & LCLK_EN))
                /* stop pixel clock before FIFO reset */
                CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN);
        /* reset FIFO */
        CAM_WRITE(pcdev, MODE, mode | RAZ_FIFO);

        omap_start_dma(pcdev->dma_ch);

        if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) {
                /*
                 * In SG mode, it's a good moment for fetching next sgbuf
                 * from the current sglist and, if available, already putting
                 * its parameters into the DMA programming register set.
                 */
                try_next_sgbuf(pcdev->dma_ch, buf);
        }

        /* (re)enable pixel clock */
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock | LCLK_EN);
        /* release FIFO reset */
        CAM_WRITE(pcdev, MODE, mode);
}

static void suspend_capture(struct omap1_cam_dev *pcdev)
{
        u32 ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK);

        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN);
        omap_stop_dma(pcdev->dma_ch);
}

static void disable_capture(struct omap1_cam_dev *pcdev)
{
        u32 mode = CAM_READ_CACHE(pcdev, MODE);

        CAM_WRITE(pcdev, MODE, mode & ~(IRQ_MASK | DMA));
}

static void omap1_videobuf_queue(struct videobuf_queue *vq,
                                                struct videobuf_buffer *vb)
{
        struct soc_camera_device *icd = vq->priv_data;
        struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
        struct omap1_cam_dev *pcdev = ici->priv;
        struct omap1_cam_buf *buf;
        u32 mode;

        list_add_tail(&vb->queue, &pcdev->capture);
        vb->state = VIDEOBUF_QUEUED;

        if (pcdev->active) {
                /*
                 * Capture in progress, so don't touch pcdev->ready even if
                 * empty. Since the transfer of the DMA programming register set
                 * content to the DMA working register set is done automatically
                 * by the DMA hardware, this can pretty well happen while we
                 * are keeping the lock here. Leave fetching it from the queue
                 * to be done when a next DMA interrupt occures instead.
                 */
                return;
        }

        WARN_ON(pcdev->ready);

        buf = prepare_next_vb(pcdev);
        if (WARN_ON(!buf))
                return;

        pcdev->active = buf;
        pcdev->ready = NULL;

        dev_dbg(icd->parent,
                "%s: capture not active, setup FIFO, start DMA\n", __func__);
        mode = CAM_READ_CACHE(pcdev, MODE) & ~THRESHOLD_MASK;
        mode |= THRESHOLD_LEVEL(pcdev->vb_mode) << THRESHOLD_SHIFT;
        CAM_WRITE(pcdev, MODE, mode | EN_FIFO_FULL | DMA);

        if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) {
                /*
                 * In SG mode, the above prepare_next_vb() didn't actually
                 * put anything into the DMA programming register set,
                 * so we have to do it now, before activating DMA.
                 */
                try_next_sgbuf(pcdev->dma_ch, buf);
        }

        start_capture(pcdev);
}

static void omap1_videobuf_release(struct videobuf_queue *vq,
                                 struct videobuf_buffer *vb)
{
        struct omap1_cam_buf *buf =
                        container_of(vb, struct omap1_cam_buf, vb);
        struct soc_camera_device *icd = vq->priv_data;
        struct device *dev = icd->parent;
        struct soc_camera_host *ici = to_soc_camera_host(dev);
        struct omap1_cam_dev *pcdev = ici->priv;

        switch (vb->state) {
        case VIDEOBUF_DONE:
                dev_dbg(dev, "%s (done)\n", __func__);
                break;
        case VIDEOBUF_ACTIVE:
                dev_dbg(dev, "%s (active)\n", __func__);
                break;
        case VIDEOBUF_QUEUED:
                dev_dbg(dev, "%s (queued)\n", __func__);
                break;
        case VIDEOBUF_PREPARED:
                dev_dbg(dev, "%s (prepared)\n", __func__);
                break;
        default:
                dev_dbg(dev, "%s (unknown %d)\n", __func__, vb->state);
                break;
        }

        free_buffer(vq, buf, pcdev->vb_mode);
}

static void videobuf_done(struct omap1_cam_dev *pcdev,
                enum videobuf_state result)
{
        struct omap1_cam_buf *buf = pcdev->active;
        struct videobuf_buffer *vb;
        struct device *dev = pcdev->soc_host.icd->parent;

        if (WARN_ON(!buf)) {
                suspend_capture(pcdev);
                disable_capture(pcdev);
                return;
        }

        if (result == VIDEOBUF_ERROR)
                suspend_capture(pcdev);

        vb = &buf->vb;
        if (waitqueue_active(&vb->done)) {
                if (!pcdev->ready && result != VIDEOBUF_ERROR) {
                        /*
                         * No next buffer has been entered into the DMA
                         * programming register set on time (could be done only
                         * while the previous DMA interurpt was processed, not
                         * later), so the last DMA block, be it a whole buffer
                         * if in CONTIG or its last sgbuf if in SG mode, is
                         * about to be reused by the just autoreinitialized DMA
                         * engine, and overwritten with next frame data. Best we
                         * can do is stopping the capture as soon as possible,
                         * hopefully before the next frame start.
                         */
                        suspend_capture(pcdev);
                }
                vb->state = result;
                v4l2_get_timestamp(&vb->ts);
                if (result != VIDEOBUF_ERROR)
                        vb->field_count++;
                wake_up(&vb->done);

                /* shift in next buffer */
                buf = pcdev->ready;
                pcdev->active = buf;
                pcdev->ready = NULL;

                if (!buf) {
                        /*
                         * No next buffer was ready on time (see above), so
                         * indicate error condition to force capture restart or
                         * stop, depending on next buffer already queued or not.
                         */
                        result = VIDEOBUF_ERROR;
                        prepare_next_vb(pcdev);

                        buf = pcdev->ready;
                        pcdev->active = buf;
                        pcdev->ready = NULL;
                }
        } else if (pcdev->ready) {
                /*
                 * In both CONTIG and SG mode, the DMA engine has possibly
                 * been already autoreinitialized with the preprogrammed
                 * pcdev->ready buffer.  We can either accept this fact
                 * and just swap the buffers, or provoke an error condition
                 * and restart capture.  The former seems less intrusive.
                 */
                dev_dbg(dev, "%s: nobody waiting on videobuf, swap with next\n",
                                __func__);
                pcdev->active = pcdev->ready;

                if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) {
                        /*
                         * In SG mode, we have to make sure that the buffer we
                         * are putting back into the pcdev->ready is marked
                         * fresh.
                         */
                        buf->sgbuf = NULL;
                }
                pcdev->ready = buf;

                buf = pcdev->active;
        } else {
                /*
                 * No next buffer has been entered into
                 * the DMA programming register set on time.
                 */
                if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                        /*
                         * In CONTIG mode, the DMA engine has already been
                         * reinitialized with the current buffer. Best we can do
                         * is not touching it.
                         */
                        dev_dbg(dev,
                                "%s: nobody waiting on videobuf, reuse it\n",
                                __func__);
                } else {
                        /*
                         * In SG mode, the DMA engine has just been
                         * autoreinitialized with the last sgbuf from the
                         * current list. Restart capture in order to transfer
                         * next frame start into the first sgbuf, not the last
                         * one.
                         */
                        if (result != VIDEOBUF_ERROR) {
                                suspend_capture(pcdev);
                                result = VIDEOBUF_ERROR;
                        }
                }
        }

        if (!buf) {
                dev_dbg(dev, "%s: no more videobufs, stop capture\n", __func__);
                disable_capture(pcdev);
                return;
        }

        if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                /*
                 * In CONTIG mode, the current buffer parameters had already
                 * been entered into the DMA programming register set while the
                 * buffer was fetched with prepare_next_vb(), they may have also
                 * been transferred into the runtime set and already active if
                 * the DMA still running.
                 */
        } else {
                /* In SG mode, extra steps are required */
                if (result == VIDEOBUF_ERROR)
                        /* make sure we (re)use sglist from start on error */
                        buf->sgbuf = NULL;

                /*
                 * In any case, enter the next sgbuf parameters into the DMA
                 * programming register set.  They will be used either during
                 * nearest DMA autoreinitialization or, in case of an error,
                 * on DMA startup below.
                 */
                try_next_sgbuf(pcdev->dma_ch, buf);
        }

        if (result == VIDEOBUF_ERROR) {
                dev_dbg(dev, "%s: videobuf error; reset FIFO, restart DMA\n",
                                __func__);
                start_capture(pcdev);
                /*
                 * In SG mode, the above also resulted in the next sgbuf
                 * parameters being entered into the DMA programming register
                 * set, making them ready for next DMA autoreinitialization.
                 */
        }

        /*
         * Finally, try fetching next buffer.
         * In CONTIG mode, it will also enter it into the DMA programming
         * register set, making it ready for next DMA autoreinitialization.
         */
        prepare_next_vb(pcdev);
}

static void dma_isr(int channel, unsigned short status, void *data)
{
        struct omap1_cam_dev *pcdev = data;
        struct omap1_cam_buf *buf = pcdev->active;
        unsigned long flags;

        spin_lock_irqsave(&pcdev->lock, flags);

        if (WARN_ON(!buf)) {
                suspend_capture(pcdev);
                disable_capture(pcdev);
                goto out;
        }

        if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                /*
                 * In CONTIG mode, assume we have just managed to collect the
                 * whole frame, hopefully before our end of frame watchdog is
                 * triggered. Then, all we have to do is disabling the watchdog
                 * for this frame, and calling videobuf_done() with success
                 * indicated.
                 */
                CAM_WRITE(pcdev, MODE,
                                CAM_READ_CACHE(pcdev, MODE) & ~EN_V_DOWN);
                videobuf_done(pcdev, VIDEOBUF_DONE);
        } else {
                /*
                 * In SG mode, we have to process every sgbuf from the current
                 * sglist, one after another.
                 */
                if (buf->sgbuf) {
                        /*
                         * Current sglist not completed yet, try fetching next
                         * sgbuf, hopefully putting it into the DMA programming
                         * register set, making it ready for next DMA
                         * autoreinitialization.
                         */
                        try_next_sgbuf(pcdev->dma_ch, buf);
                        if (buf->sgbuf)
                                goto out;

                        /*
                         * No more sgbufs left in the current sglist. This
                         * doesn't mean that the whole videobuffer is already
                         * complete, but only that the last sgbuf from the
                         * current sglist is about to be filled. It will be
                         * ready on next DMA interrupt, signalled with the
                         * buf->sgbuf set back to NULL.
                         */
                        if (buf->result != VIDEOBUF_ERROR) {
                                /*
                                 * Video frame collected without errors so far,
                                 * we can prepare for collecting a next one
                                 * as soon as DMA gets autoreinitialized
                                 * after the current (last) sgbuf is completed.
                                 */
                                buf = prepare_next_vb(pcdev);
                                if (!buf)
                                        goto out;

                                try_next_sgbuf(pcdev->dma_ch, buf);
                                goto out;
                        }
                }
                /* end of videobuf */
                videobuf_done(pcdev, buf->result);
        }

out:
        spin_unlock_irqrestore(&pcdev->lock, flags);
}

static irqreturn_t cam_isr(int irq, void *data)
{
        struct omap1_cam_dev *pcdev = data;
        struct device *dev = pcdev->soc_host.icd->parent;
        struct omap1_cam_buf *buf = pcdev->active;
        u32 it_status;
        unsigned long flags;

        it_status = CAM_READ(pcdev, IT_STATUS);
        if (!it_status)
                return IRQ_NONE;

        spin_lock_irqsave(&pcdev->lock, flags);

        if (WARN_ON(!buf)) {
                dev_warn(dev, "%s: unhandled camera interrupt, status == %#x\n",
                         __func__, it_status);
                suspend_capture(pcdev);
                disable_capture(pcdev);
                goto out;
        }

        if (unlikely(it_status & FIFO_FULL)) {
                dev_warn(dev, "%s: FIFO overflow\n", __func__);

        } else if (it_status & V_DOWN) {
                /* end of video frame watchdog */
                if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                        /*
                         * In CONTIG mode, the watchdog is disabled with
                         * successful DMA end of block interrupt, and reenabled
                         * on next frame start. If we get here, there is nothing
                         * to check, we must be out of sync.
                         */
                } else {
                        if (buf->sgcount == 2) {
                                /*
                                 * If exactly 2 sgbufs from the next sglist have
                                 * been programmed into the DMA engine (the
                                 * first one already transferred into the DMA
                                 * runtime register set, the second one still
                                 * in the programming set), then we are in sync.
                                 */
                                goto out;
                        }
                }
                dev_notice(dev, "%s: unexpected end of video frame\n",
                                __func__);

        } else if (it_status & V_UP) {
                u32 mode;

                if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) {
                        /*
                         * In CONTIG mode, we need this interrupt every frame
                         * in oredr to reenable our end of frame watchdog.
                         */
                        mode = CAM_READ_CACHE(pcdev, MODE);
                } else {
                        /*
                         * In SG mode, the below enabled end of frame watchdog
                         * is kept on permanently, so we can turn this one shot
                         * setup off.
                         */
                        mode = CAM_READ_CACHE(pcdev, MODE) & ~EN_V_UP;
                }

                if (!(mode & EN_V_DOWN)) {
                        /* (re)enable end of frame watchdog interrupt */
                        mode |= EN_V_DOWN;
                }
                CAM_WRITE(pcdev, MODE, mode);
                goto out;

        } else {
                dev_warn(dev, "%s: unhandled camera interrupt, status == %#x\n",
                                __func__, it_status);
                goto out;
        }

        videobuf_done(pcdev, VIDEOBUF_ERROR);
out:
        spin_unlock_irqrestore(&pcdev->lock, flags);
        return IRQ_HANDLED;
}

static struct videobuf_queue_ops omap1_videobuf_ops = {
        .buf_setup      = omap1_videobuf_setup,
        .buf_prepare    = omap1_videobuf_prepare,
        .buf_queue      = omap1_videobuf_queue,
        .buf_release    = omap1_videobuf_release,
};


/*
 * SOC Camera host operations
 */

static void sensor_reset(struct omap1_cam_dev *pcdev, bool reset)
{
        /* apply/release camera sensor reset if requested by platform data */
        if (pcdev->pflags & OMAP1_CAMERA_RST_HIGH)
                CAM_WRITE(pcdev, GPIO, reset);
        else if (pcdev->pflags & OMAP1_CAMERA_RST_LOW)
                CAM_WRITE(pcdev, GPIO, !reset);
}

static int omap1_cam_add_device(struct soc_camera_device *icd)
{
        dev_dbg(icd->parent, "OMAP1 Camera driver attached to camera %d\n",
                        icd->devnum);

        return 0;
}

static void omap1_cam_remove_device(struct soc_camera_device *icd)
{
        dev_dbg(icd->parent,
                "OMAP1 Camera driver detached from camera %d\n", icd->devnum);
}

/*
 * The following two functions absolutely depend on the fact, that
 * there can be only one camera on OMAP1 camera sensor interface
 */
static int omap1_cam_clock_start(struct soc_camera_host *ici)
{
        struct omap1_cam_dev *pcdev = ici->priv;
        u32 ctrlclock;

        clk_enable(pcdev->clk);

        /* setup sensor clock */
        ctrlclock = CAM_READ(pcdev, CTRLCLOCK);
        ctrlclock &= ~(CAMEXCLK_EN | MCLK_EN | DPLL_EN);
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock);

        ctrlclock &= ~FOSCMOD_MASK;
        switch (pcdev->camexclk) {
        case 6000000:
                ctrlclock |= CAMEXCLK_EN | FOSCMOD_6MHz;
                break;
        case 8000000:
                ctrlclock |= CAMEXCLK_EN | FOSCMOD_8MHz | DPLL_EN;
                break;
        case 9600000:
                ctrlclock |= CAMEXCLK_EN | FOSCMOD_9_6MHz | DPLL_EN;
                break;
        case 12000000:
                ctrlclock |= CAMEXCLK_EN | FOSCMOD_12MHz;
                break;
        case 24000000:
                ctrlclock |= CAMEXCLK_EN | FOSCMOD_24MHz | DPLL_EN;
        default:
                break;
        }
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~DPLL_EN);

        /* enable internal clock */
        ctrlclock |= MCLK_EN;
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock);

        sensor_reset(pcdev, false);

        return 0;
}

static void omap1_cam_clock_stop(struct soc_camera_host *ici)
{
        struct omap1_cam_dev *pcdev = ici->priv;
        u32 ctrlclock;

        suspend_capture(pcdev);
        disable_capture(pcdev);

        sensor_reset(pcdev, true);

        /* disable and release system clocks */
        ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK);
        ctrlclock &= ~(MCLK_EN | DPLL_EN | CAMEXCLK_EN);
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock);

        ctrlclock = (ctrlclock & ~FOSCMOD_MASK) | FOSCMOD_12MHz;
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock);
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock | MCLK_EN);

        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~MCLK_EN);

        clk_disable(pcdev->clk);
}

/* Duplicate standard formats based on host capability of byte swapping */
static const struct soc_mbus_lookup omap1_cam_formats[] = {
{
        .code = V4L2_MBUS_FMT_UYVY8_2X8,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_YUYV,
                .name                   = "YUYV",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_VYUY8_2X8,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_YVYU,
                .name                   = "YVYU",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,

        },
}, {
        .code = V4L2_MBUS_FMT_YUYV8_2X8,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_UYVY,
                .name                   = "UYVY",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_YVYU8_2X8,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_VYUY,
                .name                   = "VYUY",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_RGB555_2X8_PADHI_BE,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_RGB555,
                .name                   = "RGB555",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_RGB555_2X8_PADHI_LE,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_RGB555X,
                .name                   = "RGB555X",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_RGB565_2X8_BE,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_RGB565,
                .name                   = "RGB565",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
}, {
        .code = V4L2_MBUS_FMT_RGB565_2X8_LE,
        .fmt = {
                .fourcc                 = V4L2_PIX_FMT_RGB565X,
                .name                   = "RGB565X",
                .bits_per_sample        = 8,
                .packing                = SOC_MBUS_PACKING_2X8_PADHI,
                .order                  = SOC_MBUS_ORDER_BE,
                .layout                 = SOC_MBUS_LAYOUT_PACKED,
        },
},
};

static int omap1_cam_get_formats(struct soc_camera_device *icd,
                unsigned int idx, struct soc_camera_format_xlate *xlate)
{
        struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
        struct device *dev = icd->parent;
        int formats = 0, ret;
        enum v4l2_mbus_pixelcode code;
        const struct soc_mbus_pixelfmt *fmt;

        ret = v4l2_subdev_call(sd, video, enum_mbus_fmt, idx, &code);
        if (ret < 0)
                /* No more formats */
                return 0;

        fmt = soc_mbus_get_fmtdesc(code);
        if (!fmt) {
                dev_warn(dev, "%s: unsupported format code #%d: %d\n", __func__,
                                idx, code);
                return 0;
        }

        /* Check support for the requested bits-per-sample */
        if (fmt->bits_per_sample != 8)
                return 0;

        switch (code) {
        case V4L2_MBUS_FMT_YUYV8_2X8:
        case V4L2_MBUS_FMT_YVYU8_2X8:
        case V4L2_MBUS_FMT_UYVY8_2X8:
        case V4L2_MBUS_FMT_VYUY8_2X8:
        case V4L2_MBUS_FMT_RGB555_2X8_PADHI_BE:
        case V4L2_MBUS_FMT_RGB555_2X8_PADHI_LE:
        case V4L2_MBUS_FMT_RGB565_2X8_BE:
        case V4L2_MBUS_FMT_RGB565_2X8_LE:
                formats++;
                if (xlate) {
                        xlate->host_fmt = soc_mbus_find_fmtdesc(code,
                                                omap1_cam_formats,
                                                ARRAY_SIZE(omap1_cam_formats));
                        xlate->code     = code;
                        xlate++;
                        dev_dbg(dev,
                                "%s: providing format %s as byte swapped code #%d\n",
                                __func__, xlate->host_fmt->name, code);
                }
        default:
                if (xlate)
                        dev_dbg(dev,
                                "%s: providing format %s in pass-through mode\n",
                                __func__, fmt->name);
        }
        formats++;
        if (xlate) {
                xlate->host_fmt = fmt;
                xlate->code     = code;
                xlate++;
        }

        return formats;
}

static bool is_dma_aligned(s32 bytes_per_line, unsigned int height,
                enum omap1_cam_vb_mode vb_mode)
{
        int size = bytes_per_line * height;

        return IS_ALIGNED(bytes_per_line, DMA_ELEMENT_SIZE) &&
                IS_ALIGNED(size, DMA_FRAME_SIZE(vb_mode) * DMA_ELEMENT_SIZE);
}

static int dma_align(int *width, int *height,
                const struct soc_mbus_pixelfmt *fmt,
                enum omap1_cam_vb_mode vb_mode, bool enlarge)
{
        s32 bytes_per_line = soc_mbus_bytes_per_line(*width, fmt);

        if (bytes_per_line < 0)
                return bytes_per_line;

        if (!is_dma_aligned(bytes_per_line, *height, vb_mode)) {
                unsigned int pxalign = __fls(bytes_per_line / *width);
                unsigned int salign  = DMA_FRAME_SHIFT(vb_mode) +
                                DMA_ELEMENT_SHIFT - pxalign;
                unsigned int incr    = enlarge << salign;

                v4l_bound_align_image(width, 1, *width + incr, 0,
                                height, 1, *height + incr, 0, salign);
                return 0;
        }
        return 1;
}

#define subdev_call_with_sense(pcdev, dev, icd, sd, function, args...)               \
({                                                                                   \
        struct soc_camera_sense sense = {                                            \
                .master_clock           = pcdev->camexclk,                           \
                .pixel_clock_max        = 0,                                         \
        };                                                                           \
        int __ret;                                                                   \
                                                                                     \
        if (pcdev->pdata)                                                            \
                sense.pixel_clock_max = pcdev->pdata->lclk_khz_max * 1000;           \
        icd->sense = &sense;                                                         \
        __ret = v4l2_subdev_call(sd, video, function, ##args);                       \
        icd->sense = NULL;                                                           \
                                                                                     \
        if (sense.flags & SOCAM_SENSE_PCLK_CHANGED) {                                \
                if (sense.pixel_clock > sense.pixel_clock_max) {                     \
                        dev_err(dev,                                                 \
                                "%s: pixel clock %lu set by the camera too high!\n", \
                                __func__, sense.pixel_clock);                        \
                        __ret = -EINVAL;                                             \
                }                                                                    \
        }                                                                            \
        __ret;                                                                       \
})

static int set_mbus_format(struct omap1_cam_dev *pcdev, struct device *dev,
                struct soc_camera_device *icd, struct v4l2_subdev *sd,
                struct v4l2_mbus_framefmt *mf,
                const struct soc_camera_format_xlate *xlate)
{
        s32 bytes_per_line;
        int ret = subdev_call_with_sense(pcdev, dev, icd, sd, s_mbus_fmt, mf);

        if (ret < 0) {
                dev_err(dev, "%s: s_mbus_fmt failed\n", __func__);
                return ret;
        }

        if (mf->code != xlate->code) {
                dev_err(dev, "%s: unexpected pixel code change\n", __func__);
                return -EINVAL;
        }

        bytes_per_line = soc_mbus_bytes_per_line(mf->width, xlate->host_fmt);
        if (bytes_per_line < 0) {
                dev_err(dev, "%s: soc_mbus_bytes_per_line() failed\n",
                                __func__);
                return bytes_per_line;
        }

        if (!is_dma_aligned(bytes_per_line, mf->height, pcdev->vb_mode)) {
                dev_err(dev, "%s: resulting geometry %ux%u not DMA aligned\n",
                                __func__, mf->width, mf->height);
                return -EINVAL;
        }
        return 0;
}

static int omap1_cam_set_crop(struct soc_camera_device *icd,
                               const struct v4l2_crop *crop)
{
        const struct v4l2_rect *rect = &crop->c;
        const struct soc_camera_format_xlate *xlate = icd->current_fmt;
        struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
        struct device *dev = icd->parent;
        struct soc_camera_host *ici = to_soc_camera_host(dev);
        struct omap1_cam_dev *pcdev = ici->priv;
        struct v4l2_mbus_framefmt mf;
        int ret;

        ret = subdev_call_with_sense(pcdev, dev, icd, sd, s_crop, crop);
        if (ret < 0) {
                dev_warn(dev, "%s: failed to crop to %ux%u@%u:%u\n", __func__,
                         rect->width, rect->height, rect->left, rect->top);
                return ret;
        }

        ret = v4l2_subdev_call(sd, video, g_mbus_fmt, &mf);
        if (ret < 0) {
                dev_warn(dev, "%s: failed to fetch current format\n", __func__);
                return ret;
        }

        ret = dma_align(&mf.width, &mf.height, xlate->host_fmt, pcdev->vb_mode,
                        false);
        if (ret < 0) {
                dev_err(dev, "%s: failed to align %ux%u %s with DMA\n",
                                __func__, mf.width, mf.height,
                                xlate->host_fmt->name);
                return ret;
        }

        if (!ret) {
                /* sensor returned geometry not DMA aligned, trying to fix */
                ret = set_mbus_format(pcdev, dev, icd, sd, &mf, xlate);
                if (ret < 0) {
                        dev_err(dev, "%s: failed to set format\n", __func__);
                        return ret;
                }
        }

        icd->user_width  = mf.width;
        icd->user_height = mf.height;

        return 0;
}

static int omap1_cam_set_fmt(struct soc_camera_device *icd,
                              struct v4l2_format *f)
{
        struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
        const struct soc_camera_format_xlate *xlate;
        struct device *dev = icd->parent;
        struct soc_camera_host *ici = to_soc_camera_host(dev);
        struct omap1_cam_dev *pcdev = ici->priv;
        struct v4l2_pix_format *pix = &f->fmt.pix;
        struct v4l2_mbus_framefmt mf;
        int ret;

        xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat);
        if (!xlate) {
                dev_warn(dev, "%s: format %#x not found\n", __func__,
                                pix->pixelformat);
                return -EINVAL;
        }

        mf.width        = pix->width;
        mf.height       = pix->height;
        mf.field        = pix->field;
        mf.colorspace   = pix->colorspace;
        mf.code         = xlate->code;

        ret = dma_align(&mf.width, &mf.height, xlate->host_fmt, pcdev->vb_mode,
                        true);
        if (ret < 0) {
                dev_err(dev, "%s: failed to align %ux%u %s with DMA\n",
                                __func__, pix->width, pix->height,
                                xlate->host_fmt->name);
                return ret;
        }

        ret = set_mbus_format(pcdev, dev, icd, sd, &mf, xlate);
        if (ret < 0) {
                dev_err(dev, "%s: failed to set format\n", __func__);
                return ret;
        }

        pix->width       = mf.width;
        pix->height      = mf.height;
        pix->field       = mf.field;
        pix->colorspace  = mf.colorspace;
        icd->current_fmt = xlate;

        return 0;
}

static int omap1_cam_try_fmt(struct soc_camera_device *icd,
                              struct v4l2_format *f)
{
        struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
        const struct soc_camera_format_xlate *xlate;
        struct v4l2_pix_format *pix = &f->fmt.pix;
        struct v4l2_mbus_framefmt mf;
        int ret;
        /* TODO: limit to mx1 hardware capabilities */

        xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat);
        if (!xlate) {
                dev_warn(icd->parent, "Format %#x not found\n",
                         pix->pixelformat);
                return -EINVAL;
        }

        mf.width        = pix->width;
        mf.height       = pix->height;
        mf.field        = pix->field;
        mf.colorspace   = pix->colorspace;
        mf.code         = xlate->code;

        /* limit to sensor capabilities */
        ret = v4l2_subdev_call(sd, video, try_mbus_fmt, &mf);
        if (ret < 0)
                return ret;

        pix->width      = mf.width;
        pix->height     = mf.height;
        pix->field      = mf.field;
        pix->colorspace = mf.colorspace;

        return 0;
}

static bool sg_mode;

/*
 * Local mmap_mapper wrapper,
 * used for detecting videobuf-dma-contig buffer allocation failures
 * and switching to videobuf-dma-sg automatically for future attempts.
 */
static int omap1_cam_mmap_mapper(struct videobuf_queue *q,
                                  struct videobuf_buffer *buf,
                                  struct vm_area_struct *vma)
{
        struct soc_camera_device *icd = q->priv_data;
        struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
        struct omap1_cam_dev *pcdev = ici->priv;
        int ret;

        ret = pcdev->mmap_mapper(q, buf, vma);

        if (ret == -ENOMEM)
                sg_mode = true;

        return ret;
}

static void omap1_cam_init_videobuf(struct videobuf_queue *q,
                                     struct soc_camera_device *icd)
{
        struct soc_camera_host *ici = to_soc_camera_host(icd->parent);
        struct omap1_cam_dev *pcdev = ici->priv;

        if (!sg_mode)
                videobuf_queue_dma_contig_init(q, &omap1_videobuf_ops,
                                icd->parent, &pcdev->lock,
                                V4L2_BUF_TYPE_VIDEO_CAPTURE, V4L2_FIELD_NONE,
                                sizeof(struct omap1_cam_buf), icd, &ici->host_lock);
        else
                videobuf_queue_sg_init(q, &omap1_videobuf_ops,
                                icd->parent, &pcdev->lock,
                                V4L2_BUF_TYPE_VIDEO_CAPTURE, V4L2_FIELD_NONE,
                                sizeof(struct omap1_cam_buf), icd, &ici->host_lock);

        /* use videobuf mode (auto)selected with the module parameter */
        pcdev->vb_mode = sg_mode ? OMAP1_CAM_DMA_SG : OMAP1_CAM_DMA_CONTIG;

        /*
         * Ensure we substitute the videobuf-dma-contig version of the
         * mmap_mapper() callback with our own wrapper, used for switching
         * automatically to videobuf-dma-sg on buffer allocation failure.
         */
        if (!sg_mode && q->int_ops->mmap_mapper != omap1_cam_mmap_mapper) {
                pcdev->mmap_mapper = q->int_ops->mmap_mapper;
                q->int_ops->mmap_mapper = omap1_cam_mmap_mapper;
        }
}

static int omap1_cam_reqbufs(struct soc_camera_device *icd,
                              struct v4l2_requestbuffers *p)
{
        int i;

        /*
         * This is for locking debugging only. I removed spinlocks and now I
         * check whether .prepare is ever called on a linked buffer, or whether
         * a dma IRQ can occur for an in-work or unlinked buffer. Until now
         * it hadn't triggered
         */
        for (i = 0; i < p->count; i++) {
                struct omap1_cam_buf *buf = container_of(icd->vb_vidq.bufs[i],
                                                      struct omap1_cam_buf, vb);
                buf->inwork = 0;
                INIT_LIST_HEAD(&buf->vb.queue);
        }

        return 0;
}

static int omap1_cam_querycap(struct soc_camera_host *ici,
                               struct v4l2_capability *cap)
{
        /* cap->name is set by the friendly caller:-> */
        strlcpy(cap->card, "OMAP1 Camera", sizeof(cap->card));
        cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING;

        return 0;
}

static int omap1_cam_set_bus_param(struct soc_camera_device *icd)
{
        struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
        struct device *dev = icd->parent;
        struct soc_camera_host *ici = to_soc_camera_host(dev);
        struct omap1_cam_dev *pcdev = ici->priv;
        u32 pixfmt = icd->current_fmt->host_fmt->fourcc;
        const struct soc_camera_format_xlate *xlate;
        const struct soc_mbus_pixelfmt *fmt;
        struct v4l2_mbus_config cfg = {.type = V4L2_MBUS_PARALLEL,};
        unsigned long common_flags;
        u32 ctrlclock, mode;
        int ret;

        ret = v4l2_subdev_call(sd, video, g_mbus_config, &cfg);
        if (!ret) {
                common_flags = soc_mbus_config_compatible(&cfg, SOCAM_BUS_FLAGS);
                if (!common_flags) {
                        dev_warn(dev,
                                 "Flags incompatible: camera 0x%x, host 0x%x\n",
                                 cfg.flags, SOCAM_BUS_FLAGS);
                        return -EINVAL;
                }
        } else if (ret != -ENOIOCTLCMD) {
                return ret;
        } else {
                common_flags = SOCAM_BUS_FLAGS;
        }

        /* Make choices, possibly based on platform configuration */
        if ((common_flags & V4L2_MBUS_PCLK_SAMPLE_RISING) &&
                        (common_flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)) {
                if (!pcdev->pdata ||
                                pcdev->pdata->flags & OMAP1_CAMERA_LCLK_RISING)
                        common_flags &= ~V4L2_MBUS_PCLK_SAMPLE_FALLING;
                else
                        common_flags &= ~V4L2_MBUS_PCLK_SAMPLE_RISING;
        }

        cfg.flags = common_flags;
        ret = v4l2_subdev_call(sd, video, s_mbus_config, &cfg);
        if (ret < 0 && ret != -ENOIOCTLCMD) {
                dev_dbg(dev, "camera s_mbus_config(0x%lx) returned %d\n",
                        common_flags, ret);
                return ret;
        }

        ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK);
        if (ctrlclock & LCLK_EN)
                CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN);

        if (common_flags & V4L2_MBUS_PCLK_SAMPLE_RISING) {
                dev_dbg(dev, "CTRLCLOCK_REG |= POLCLK\n");
                ctrlclock |= POLCLK;
        } else {
                dev_dbg(dev, "CTRLCLOCK_REG &= ~POLCLK\n");
                ctrlclock &= ~POLCLK;
        }
        CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN);

        if (ctrlclock & LCLK_EN)
                CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock);

        /* select bus endianess */
        xlate = soc_camera_xlate_by_fourcc(icd, pixfmt);
        fmt = xlate->host_fmt;

        mode = CAM_READ(pcdev, MODE) & ~(RAZ_FIFO | IRQ_MASK | DMA);
        if (fmt->order == SOC_MBUS_ORDER_LE) {
                dev_dbg(dev, "MODE_REG &= ~ORDERCAMD\n");
                CAM_WRITE(pcdev, MODE, mode & ~ORDERCAMD);
        } else {
                dev_dbg(dev, "MODE_REG |= ORDERCAMD\n");
                CAM_WRITE(pcdev, MODE, mode | ORDERCAMD);
        }

        return 0;
}

static unsigned int omap1_cam_poll(struct file *file, poll_table *pt)
{
        struct soc_camera_device *icd = file->private_data;
        struct omap1_cam_buf *buf;

        buf = list_entry(icd->vb_vidq.stream.next, struct omap1_cam_buf,
                         vb.stream);

        poll_wait(file, &buf->vb.done, pt);

        if (buf->vb.state == VIDEOBUF_DONE ||
            buf->vb.state == VIDEOBUF_ERROR)
                return POLLIN | POLLRDNORM;

        return 0;
}

static struct soc_camera_host_ops omap1_host_ops = {
        .owner          = THIS_MODULE,
        .add            = omap1_cam_add_device,
        .remove         = omap1_cam_remove_device,
        .clock_start    = omap1_cam_clock_start,
        .clock_stop     = omap1_cam_clock_stop,
        .get_formats    = omap1_cam_get_formats,
        .set_crop       = omap1_cam_set_crop,
        .set_fmt        = omap1_cam_set_fmt,
        .try_fmt        = omap1_cam_try_fmt,
        .init_videobuf  = omap1_cam_init_videobuf,
        .reqbufs        = omap1_cam_reqbufs,
        .querycap       = omap1_cam_querycap,
        .set_bus_param  = omap1_cam_set_bus_param,
        .poll           = omap1_cam_poll,
};

static int omap1_cam_probe(struct platform_device *pdev)
{
        struct omap1_cam_dev *pcdev;
        struct resource *res;
        struct clk *clk;
        void __iomem *base;
        unsigned int irq;
        int err = 0;

        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        irq = platform_get_irq(pdev, 0);
        if (!res || (int)irq <= 0) {
                err = -ENODEV;
                goto exit;
        }

        clk = clk_get(&pdev->dev, "armper_ck");
        if (IS_ERR(clk)) {
                err = PTR_ERR(clk);
                goto exit;
        }

        pcdev = kzalloc(sizeof(*pcdev) + resource_size(res), GFP_KERNEL);
        if (!pcdev) {
                dev_err(&pdev->dev, "Could not allocate pcdev\n");
                err = -ENOMEM;
                goto exit_put_clk;
        }

        pcdev->res = res;
        pcdev->clk = clk;

        pcdev->pdata = pdev->dev.platform_data;
        if (pcdev->pdata) {
                pcdev->pflags = pcdev->pdata->flags;
                pcdev->camexclk = pcdev->pdata->camexclk_khz * 1000;
        }

        switch (pcdev->camexclk) {
        case 6000000:
        case 8000000:
        case 9600000:
        case 12000000:
        case 24000000:
                break;
        default:
                /* pcdev->camexclk != 0 => pcdev->pdata != NULL */
                dev_warn(&pdev->dev,
                                "Incorrect sensor clock frequency %ld kHz, "
                                "should be one of 0, 6, 8, 9.6, 12 or 24 MHz, "
                                "please correct your platform data\n",
                                pcdev->pdata->camexclk_khz);
                pcdev->camexclk = 0;
        case 0:
                dev_info(&pdev->dev, "Not providing sensor clock\n");
        }

        INIT_LIST_HEAD(&pcdev->capture);
        spin_lock_init(&pcdev->lock);

        /*
         * Request the region.
         */
        if (!request_mem_region(res->start, resource_size(res), DRIVER_NAME)) {
                err = -EBUSY;
                goto exit_kfree;
        }

        base = ioremap(res->start, resource_size(res));
        if (!base) {
                err = -ENOMEM;
                goto exit_release;
        }
        pcdev->irq = irq;
        pcdev->base = base;

        sensor_reset(pcdev, true);

        err = omap_request_dma(OMAP_DMA_CAMERA_IF_RX, DRIVER_NAME,
                        dma_isr, (void *)pcdev, &pcdev->dma_ch);
        if (err < 0) {
                dev_err(&pdev->dev, "Can't request DMA for OMAP1 Camera\n");
                err = -EBUSY;
                goto exit_iounmap;
        }
        dev_dbg(&pdev->dev, "got DMA channel %d\n", pcdev->dma_ch);

        /* preconfigure DMA */
        omap_set_dma_src_params(pcdev->dma_ch, OMAP_DMA_PORT_TIPB,
                        OMAP_DMA_AMODE_CONSTANT, res->start + REG_CAMDATA,
                        0, 0);
        omap_set_dma_dest_burst_mode(pcdev->dma_ch, OMAP_DMA_DATA_BURST_4);
        /* setup DMA autoinitialization */
        omap_dma_link_lch(pcdev->dma_ch, pcdev->dma_ch);

        err = request_irq(pcdev->irq, cam_isr, 0, DRIVER_NAME, pcdev);
        if (err) {
                dev_err(&pdev->dev, "Camera interrupt register failed\n");
                goto exit_free_dma;
        }

        pcdev->soc_host.drv_name        = DRIVER_NAME;
        pcdev->soc_host.ops             = &omap1_host_ops;
        pcdev->soc_host.priv            = pcdev;
        pcdev->soc_host.v4l2_dev.dev    = &pdev->dev;
        pcdev->soc_host.nr              = pdev->id;

        err = soc_camera_host_register(&pcdev->soc_host);
        if (err)
                goto exit_free_irq;

        dev_info(&pdev->dev, "OMAP1 Camera Interface driver loaded\n");

        return 0;

exit_free_irq:
        free_irq(pcdev->irq, pcdev);
exit_free_dma:
        omap_free_dma(pcdev->dma_ch);
exit_iounmap:
        iounmap(base);
exit_release:
        release_mem_region(res->start, resource_size(res));
exit_kfree:
        kfree(pcdev);
exit_put_clk:
        clk_put(clk);
exit:
        return err;
}

static int omap1_cam_remove(struct platform_device *pdev)
{
        struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev);
        struct omap1_cam_dev *pcdev = container_of(soc_host,
                                        struct omap1_cam_dev, soc_host);
        struct resource *res;

        free_irq(pcdev->irq, pcdev);

        omap_free_dma(pcdev->dma_ch);

        soc_camera_host_unregister(soc_host);

        iounmap(pcdev->base);

        res = pcdev->res;
        release_mem_region(res->start, resource_size(res));

        clk_put(pcdev->clk);

        kfree(pcdev);

        dev_info(&pdev->dev, "OMAP1 Camera Interface driver unloaded\n");

        return 0;
}

static struct platform_driver omap1_cam_driver = {
        .driver         = {
                .name   = DRIVER_NAME,
        },
        .probe          = omap1_cam_probe,
        .remove         = omap1_cam_remove,
};

module_platform_driver(omap1_cam_driver);

module_param(sg_mode, bool, 0644);
MODULE_PARM_DESC(sg_mode, "videobuf mode, 0: dma-contig (default), 1: dma-sg");

MODULE_DESCRIPTION("OMAP1 Camera Interface driver");
MODULE_AUTHOR("Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>");
MODULE_LICENSE("GPL v2");
MODULE_VERSION(DRIVER_VERSION);
MODULE_ALIAS("platform:" DRIVER_NAME);