1/************************************************************************ 2 * 3 * 16654.H Definitions for 16C654 UART used on EdgePorts 4 * 5 * Copyright (C) 1998 Inside Out Networks, Inc. 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License as published by 8 * the Free Software Foundation; either version 2 of the License, or 9 * (at your option) any later version. 10 * 11 ************************************************************************/ 12 13#if !defined(_16654_H) 14#define _16654_H 15 16/************************************************************************ 17 * 18 * D e f i n e s / T y p e d e f s 19 * 20 ************************************************************************/ 21 22 // 23 // UART register numbers 24 // Numbers 0-7 are passed to the Edgeport directly. Numbers 8 and 25 // above are used internally to indicate that we must enable access 26 // to them via LCR bit 0x80 or LCR = 0xBF. 27 // The register number sent to the Edgeport is then (x & 0x7). 28 // 29 // Driver must not access registers that affect operation of the 30 // the EdgePort firmware -- that includes THR, RHR, IER, FCR. 31 32 33#define THR 0 // ! Transmit Holding Register (Write) 34#define RDR 0 // ! Receive Holding Register (Read) 35#define IER 1 // ! Interrupt Enable Register 36#define FCR 2 // ! Fifo Control Register (Write) 37#define ISR 2 // Interrupt Status Register (Read) 38#define LCR 3 // Line Control Register 39#define MCR 4 // Modem Control Register 40#define LSR 5 // Line Status Register 41#define MSR 6 // Modem Status Register 42#define SPR 7 // ScratchPad Register 43#define DLL 8 // Bank2[ 0 ] Divisor Latch LSB 44#define DLM 9 // Bank2[ 1 ] Divisor Latch MSB 45#define EFR 10 // Bank2[ 2 ] Extended Function Register 46//efine unused 11 // Bank2[ 3 ] 47#define XON1 12 // Bank2[ 4 ] Xon-1 48#define XON2 13 // Bank2[ 5 ] Xon-2 49#define XOFF1 14 // Bank2[ 6 ] Xoff-1 50#define XOFF2 15 // Bank2[ 7 ] Xoff-2 51 52#define NUM_16654_REGS 16 53 54#define IS_REG_2ND_BANK(x) ((x) >= 8) 55 56 // 57 // Bit definitions for each register 58 // 59 60#define IER_RX 0x01 // Enable receive interrupt 61#define IER_TX 0x02 // Enable transmit interrupt 62#define IER_RXS 0x04 // Enable receive status interrupt 63#define IER_MDM 0x08 // Enable modem status interrupt 64#define IER_SLEEP 0x10 // Enable sleep mode 65#define IER_XOFF 0x20 // Enable s/w flow control (XOFF) interrupt 66#define IER_RTS 0x40 // Enable RTS interrupt 67#define IER_CTS 0x80 // Enable CTS interrupt 68#define IER_ENABLE_ALL 0xFF // Enable all ints 69 70 71#define FCR_FIFO_EN 0x01 // Enable FIFOs 72#define FCR_RXCLR 0x02 // Reset Rx FIFO 73#define FCR_TXCLR 0x04 // Reset Tx FIFO 74#define FCR_DMA_BLK 0x08 // Enable DMA block mode 75#define FCR_TX_LEVEL_MASK 0x30 // Mask for Tx FIFO Level 76#define FCR_TX_LEVEL_8 0x00 // Tx FIFO Level = 8 bytes 77#define FCR_TX_LEVEL_16 0x10 // Tx FIFO Level = 16 bytes 78#define FCR_TX_LEVEL_32 0x20 // Tx FIFO Level = 32 bytes 79#define FCR_TX_LEVEL_56 0x30 // Tx FIFO Level = 56 bytes 80#define FCR_RX_LEVEL_MASK 0xC0 // Mask for Rx FIFO Level 81#define FCR_RX_LEVEL_8 0x00 // Rx FIFO Level = 8 bytes 82#define FCR_RX_LEVEL_16 0x40 // Rx FIFO Level = 16 bytes 83#define FCR_RX_LEVEL_56 0x80 // Rx FIFO Level = 56 bytes 84#define FCR_RX_LEVEL_60 0xC0 // Rx FIFO Level = 60 bytes 85 86 87#define ISR_INT_MDM_STATUS 0x00 // Modem status int pending 88#define ISR_INT_NONE 0x01 // No interrupt pending 89#define ISR_INT_TXRDY 0x02 // Tx ready int pending 90#define ISR_INT_RXRDY 0x04 // Rx ready int pending 91#define ISR_INT_LINE_STATUS 0x06 // Line status int pending 92#define ISR_INT_RX_TIMEOUT 0x0C // Rx timeout int pending 93#define ISR_INT_RX_XOFF 0x10 // Rx Xoff int pending 94#define ISR_INT_RTS_CTS 0x20 // RTS/CTS change int pending 95#define ISR_FIFO_ENABLED 0xC0 // Bits set if FIFOs enabled 96#define ISR_INT_BITS_MASK 0x3E // Mask to isolate valid int causes 97 98 99#define LCR_BITS_5 0x00 // 5 bits/char 100#define LCR_BITS_6 0x01 // 6 bits/char 101#define LCR_BITS_7 0x02 // 7 bits/char 102#define LCR_BITS_8 0x03 // 8 bits/char 103#define LCR_BITS_MASK 0x03 // Mask for bits/char field 104 105#define LCR_STOP_1 0x00 // 1 stop bit 106#define LCR_STOP_1_5 0x04 // 1.5 stop bits (if 5 bits/char) 107#define LCR_STOP_2 0x04 // 2 stop bits (if 6-8 bits/char) 108#define LCR_STOP_MASK 0x04 // Mask for stop bits field 109 110#define LCR_PAR_NONE 0x00 // No parity 111#define LCR_PAR_ODD 0x08 // Odd parity 112#define LCR_PAR_EVEN 0x18 // Even parity 113#define LCR_PAR_MARK 0x28 // Force parity bit to 1 114#define LCR_PAR_SPACE 0x38 // Force parity bit to 0 115#define LCR_PAR_MASK 0x38 // Mask for parity field 116 117#define LCR_SET_BREAK 0x40 // Set Break condition 118#define LCR_DL_ENABLE 0x80 // Enable access to divisor latch 119 120#define LCR_ACCESS_EFR 0xBF // Load this value to access DLL,DLM, 121 // and also the '654-only registers 122 // EFR, XON1, XON2, XOFF1, XOFF2 123 124 125#define MCR_DTR 0x01 // Assert DTR 126#define MCR_RTS 0x02 // Assert RTS 127#define MCR_OUT1 0x04 // Loopback only: Sets state of RI 128#define MCR_MASTER_IE 0x08 // Enable interrupt outputs 129#define MCR_LOOPBACK 0x10 // Set internal (digital) loopback mode 130#define MCR_XON_ANY 0x20 // Enable any char to exit XOFF mode 131#define MCR_IR_ENABLE 0x40 // Enable IrDA functions 132#define MCR_BRG_DIV_4 0x80 // Divide baud rate clk by /4 instead of /1 133 134 135#define LSR_RX_AVAIL 0x01 // Rx data available 136#define LSR_OVER_ERR 0x02 // Rx overrun 137#define LSR_PAR_ERR 0x04 // Rx parity error 138#define LSR_FRM_ERR 0x08 // Rx framing error 139#define LSR_BREAK 0x10 // Rx break condition detected 140#define LSR_TX_EMPTY 0x20 // Tx Fifo empty 141#define LSR_TX_ALL_EMPTY 0x40 // Tx Fifo and shift register empty 142#define LSR_FIFO_ERR 0x80 // Rx Fifo contains at least 1 erred char 143 144 145#define EDGEPORT_MSR_DELTA_CTS 0x01 // CTS changed from last read 146#define EDGEPORT_MSR_DELTA_DSR 0x02 // DSR changed from last read 147#define EDGEPORT_MSR_DELTA_RI 0x04 // RI changed from 0 -> 1 148#define EDGEPORT_MSR_DELTA_CD 0x08 // CD changed from last read 149#define EDGEPORT_MSR_CTS 0x10 // Current state of CTS 150#define EDGEPORT_MSR_DSR 0x20 // Current state of DSR 151#define EDGEPORT_MSR_RI 0x40 // Current state of RI 152#define EDGEPORT_MSR_CD 0x80 // Current state of CD 153 154 155 156 // Tx Rx 157 //------------------------------- 158#define EFR_SWFC_NONE 0x00 // None None 159#define EFR_SWFC_RX1 0x02 // None XOFF1 160#define EFR_SWFC_RX2 0x01 // None XOFF2 161#define EFR_SWFC_RX12 0x03 // None XOFF1 & XOFF2 162#define EFR_SWFC_TX1 0x08 // XOFF1 None 163#define EFR_SWFC_TX1_RX1 0x0a // XOFF1 XOFF1 164#define EFR_SWFC_TX1_RX2 0x09 // XOFF1 XOFF2 165#define EFR_SWFC_TX1_RX12 0x0b // XOFF1 XOFF1 & XOFF2 166#define EFR_SWFC_TX2 0x04 // XOFF2 None 167#define EFR_SWFC_TX2_RX1 0x06 // XOFF2 XOFF1 168#define EFR_SWFC_TX2_RX2 0x05 // XOFF2 XOFF2 169#define EFR_SWFC_TX2_RX12 0x07 // XOFF2 XOFF1 & XOFF2 170#define EFR_SWFC_TX12 0x0c // XOFF1 & XOFF2 None 171#define EFR_SWFC_TX12_RX1 0x0e // XOFF1 & XOFF2 XOFF1 172#define EFR_SWFC_TX12_RX2 0x0d // XOFF1 & XOFF2 XOFF2 173#define EFR_SWFC_TX12_RX12 0x0f // XOFF1 & XOFF2 XOFF1 & XOFF2 174 175#define EFR_TX_FC_MASK 0x0c // Mask to isolate Rx flow control 176#define EFR_TX_FC_NONE 0x00 // No Tx Xon/Xoff flow control 177#define EFR_TX_FC_X1 0x08 // Transmit Xon1/Xoff1 178#define EFR_TX_FC_X2 0x04 // Transmit Xon2/Xoff2 179#define EFR_TX_FC_X1_2 0x0c // Transmit Xon1&2/Xoff1&2 180 181#define EFR_RX_FC_MASK 0x03 // Mask to isolate Rx flow control 182#define EFR_RX_FC_NONE 0x00 // No Rx Xon/Xoff flow control 183#define EFR_RX_FC_X1 0x02 // Receiver compares Xon1/Xoff1 184#define EFR_RX_FC_X2 0x01 // Receiver compares Xon2/Xoff2 185#define EFR_RX_FC_X1_2 0x03 // Receiver compares Xon1&2/Xoff1&2 186 187 188#define EFR_SWFC_MASK 0x0F // Mask for software flow control field 189#define EFR_ENABLE_16654 0x10 // Enable 16C654 features 190#define EFR_SPEC_DETECT 0x20 // Enable special character detect interrupt 191#define EFR_AUTO_RTS 0x40 // Use RTS for Rx flow control 192#define EFR_AUTO_CTS 0x80 // Use CTS for Tx flow control 193 194#endif // if !defined(_16654_H) 195 196