linux/drivers/atm/midway.h
<<
>>
Prefs
   1/* drivers/atm/midway.h - Efficient Networks Midway (SAR) description */
   2 
   3/* Written 1995-1999 by Werner Almesberger, EPFL LRC/ICA */
   4 
   5
   6#ifndef DRIVERS_ATM_MIDWAY_H
   7#define DRIVERS_ATM_MIDWAY_H
   8
   9
  10#define NR_VCI          1024            /* number of VCIs */
  11#define NR_VCI_LD       10              /* log2(NR_VCI) */
  12#define NR_DMA_RX       512             /* RX DMA queue entries */
  13#define NR_DMA_TX       512             /* TX DMA queue entries */
  14#define NR_SERVICE      NR_VCI          /* service list size */
  15#define NR_CHAN         8               /* number of TX channels */
  16#define TS_CLOCK        25000000        /* traffic shaper clock (cell/sec) */
  17
  18#define MAP_MAX_SIZE    0x00400000      /* memory window for max config */
  19#define EPROM_SIZE      0x00010000
  20#define MEM_VALID       0xffc00000      /* mask base address with this */
  21#define PHY_BASE        0x00020000      /* offset of PHY register are */
  22#define REG_BASE        0x00040000      /* offset of Midway register area */
  23#define RAM_BASE        0x00200000      /* offset of RAM area */
  24#define RAM_INCREMENT   0x00020000      /* probe for RAM every 128kB */
  25
  26#define MID_VCI_BASE    RAM_BASE
  27#define MID_DMA_RX_BASE (MID_VCI_BASE+NR_VCI*16)
  28#define MID_DMA_TX_BASE (MID_DMA_RX_BASE+NR_DMA_RX*8)
  29#define MID_SERVICE_BASE (MID_DMA_TX_BASE+NR_DMA_TX*8)
  30#define MID_FREE_BASE   (MID_SERVICE_BASE+NR_SERVICE*4)
  31
  32#define MAC_LEN 6 /* atm.h */
  33
  34#define MID_MIN_BUF_SIZE (1024)         /*   1 kB is minimum */
  35#define MID_MAX_BUF_SIZE (128*1024)     /* 128 kB is maximum */
  36
  37#define RX_DESCR_SIZE   1               /* RX PDU descr is 1 longword */
  38#define TX_DESCR_SIZE   2               /* TX PDU descr is 2 longwords */
  39#define AAL5_TRAILER    (ATM_AAL5_TRAILER/4) /* AAL5 trailer is 2 longwords */
  40
  41#define TX_GAP          8               /* TX buffer gap (words) */
  42
  43/*
  44 * Midway Reset/ID
  45 *
  46 * All values read-only. Writing to this register resets Midway chip.
  47 */
  48
  49#define MID_RES_ID_MCON 0x00            /* Midway Reset/ID */
  50
  51#define MID_ID          0xf0000000      /* Midway version */
  52#define MID_SHIFT       24
  53#define MID_MOTHER_ID   0x00000700      /* mother board id */
  54#define MID_MOTHER_SHIFT 8
  55#define MID_CON_TI      0x00000080      /* 0: normal ctrl; 1: SABRE */
  56#define MID_CON_SUNI    0x00000040      /* 0: UTOPIA; 1: SUNI */
  57#define MID_CON_V6      0x00000020      /* 0: non-pipel UTOPIA (required iff
  58                                           !CON_SUNI; 1: UTOPIA */
  59#define DAUGTHER_ID     0x0000001f      /* daugther board id */
  60
  61/*
  62 * Interrupt Status Acknowledge, Interrupt Status & Interrupt Enable
  63 */
  64
  65#define MID_ISA         0x01            /* Interrupt Status Acknowledge */
  66#define MID_IS          0x02            /* Interrupt Status */
  67#define MID_IE          0x03            /* Interrupt Enable */
  68
  69#define MID_TX_COMPLETE_7 0x00010000    /* channel N completed a PDU */
  70#define MID_TX_COMPLETE_6 0x00008000    /* transmission */
  71#define MID_TX_COMPLETE_5 0x00004000
  72#define MID_TX_COMPLETE_4 0x00002000
  73#define MID_TX_COMPLETE_3 0x00001000
  74#define MID_TX_COMPLETE_2 0x00000800
  75#define MID_TX_COMPLETE_1 0x00000400
  76#define MID_TX_COMPLETE_0 0x00000200
  77#define MID_TX_COMPLETE 0x0001fe00      /* any TX */
  78#define MID_TX_DMA_OVFL 0x00000100      /* DMA to adapter overflow */
  79#define MID_TX_IDENT_MISM 0x00000080    /* TX: ident mismatch => halted */
  80#define MID_DMA_LERR_ACK 0x00000040     /* LERR - SBus ? */
  81#define MID_DMA_ERR_ACK 0x00000020      /* DMA error */
  82#define MID_RX_DMA_COMPLETE 0x00000010  /* DMA to host done */
  83#define MID_TX_DMA_COMPLETE 0x00000008  /* DMA from host done */
  84#define MID_SERVICE     0x00000004      /* something in service list */
  85#define MID_SUNI_INT    0x00000002      /* interrupt from SUNI */
  86#define MID_STAT_OVFL   0x00000001      /* statistics overflow */
  87
  88/*
  89 * Master Control/Status
  90 */
  91
  92#define MID_MC_S        0x04
  93
  94#define MID_INT_SELECT  0x000001C0      /* Interrupt level (000: off) */
  95#define MID_INT_SEL_SHIFT 6
  96#define MID_TX_LOCK_MODE 0x00000020     /* 0: streaming; 1: TX ovfl->lock */
  97#define MID_DMA_ENABLE  0x00000010      /* R: 0: disable; 1: enable
  98                                           W: 0: no change; 1: enable */
  99#define MID_TX_ENABLE   0x00000008      /* R: 0: TX disabled; 1: enabled
 100                                           W: 0: no change; 1: enable */
 101#define MID_RX_ENABLE   0x00000004      /* like TX */
 102#define MID_WAIT_1MS    0x00000002      /* R: 0: timer not running; 1: running
 103                                           W: 0: no change; 1: no interrupts
 104                                                               for 1 ms */
 105#define MID_WAIT_500US  0x00000001      /* like WAIT_1MS, but 0.5 ms */
 106
 107/*
 108 * Statistics
 109 *
 110 * Cleared when reading.
 111 */
 112
 113#define MID_STAT                0x05
 114
 115#define MID_VCI_TRASH   0xFFFF0000      /* trashed cells because of VCI mode */
 116#define MID_VCI_TRASH_SHIFT 16
 117#define MID_OVFL_TRASH  0x0000FFFF      /* trashed cells because of overflow */
 118
 119/*
 120 * Address registers
 121 */
 122
 123#define MID_SERV_WRITE  0x06    /* free pos in service area (R, 10 bits) */
 124#define MID_DMA_ADDR    0x07    /* virtual DMA address (R, 32 bits) */
 125#define MID_DMA_WR_RX   0x08    /* (RW, 9 bits) */
 126#define MID_DMA_RD_RX   0x09
 127#define MID_DMA_WR_TX   0x0A
 128#define MID_DMA_RD_TX   0x0B
 129
 130/*
 131 * Transmit Place Registers (0x10+4*channel)
 132 */
 133
 134#define MID_TX_PLACE(c) (0x10+4*(c))
 135
 136#define MID_SIZE        0x00003800      /* size, N*256 x 32 bit */
 137#define MID_SIZE_SHIFT  11
 138#define MID_LOCATION    0x000007FF      /* location in adapter memory (word) */
 139
 140#define MID_LOC_SKIP    8               /* 8 bits of location are always zero
 141                                           (applies to all uses of location) */
 142
 143/*
 144 * Transmit ReadPtr Registers (0x11+4*channel)
 145 */
 146
 147#define MID_TX_RDPTR(c) (0x11+4*(c))
 148
 149#define MID_READ_PTR    0x00007FFF      /* next word for PHY */
 150
 151/*
 152 * Transmit DescrStart Registers (0x12+4*channel)
 153 */
 154
 155#define MID_TX_DESCRSTART(c) (0x12+4*(c))
 156
 157#define MID_DESCR_START 0x00007FFF      /* seg buffer being DMAed */
 158
 159#define ENI155_MAGIC    0xa54b872d
 160
 161struct midway_eprom {
 162        unsigned char mac[MAC_LEN],inv_mac[MAC_LEN];
 163        unsigned char pad[36];
 164        u32 serial,inv_serial;
 165        u32 magic,inv_magic;
 166};
 167
 168
 169/*
 170 * VCI table entry
 171 */
 172
 173#define MID_VCI_IN_SERVICE      0x00000001      /* set if VCI is currently in
 174                                                   service list */
 175#define MID_VCI_SIZE            0x00038000      /* reassembly buffer size,
 176                                                   2*<size> kB */
 177#define MID_VCI_SIZE_SHIFT      15
 178#define MID_VCI_LOCATION        0x1ffc0000      /* buffer location */
 179#define MID_VCI_LOCATION_SHIFT  18
 180#define MID_VCI_PTI_MODE        0x20000000      /* 0: trash, 1: preserve */
 181#define MID_VCI_MODE            0xc0000000
 182#define MID_VCI_MODE_SHIFT      30
 183#define MID_VCI_READ            0x00007fff
 184#define MID_VCI_READ_SHIFT      0
 185#define MID_VCI_DESCR           0x7fff0000
 186#define MID_VCI_DESCR_SHIFT     16
 187#define MID_VCI_COUNT           0x000007ff
 188#define MID_VCI_COUNT_SHIFT     0
 189#define MID_VCI_STATE           0x0000c000
 190#define MID_VCI_STATE_SHIFT     14
 191#define MID_VCI_WRITE           0x7fff0000
 192#define MID_VCI_WRITE_SHIFT     16
 193
 194#define MID_MODE_TRASH  0
 195#define MID_MODE_RAW    1
 196#define MID_MODE_AAL5   2
 197
 198/*
 199 * Reassembly buffer descriptor
 200 */
 201
 202#define MID_RED_COUNT           0x000007ff
 203#define MID_RED_CRC_ERR         0x00000800
 204#define MID_RED_T               0x00001000
 205#define MID_RED_CE              0x00010000
 206#define MID_RED_CLP             0x01000000
 207#define MID_RED_IDEN            0xfe000000
 208#define MID_RED_SHIFT           25
 209
 210#define MID_RED_RX_ID           0x1b            /* constant identifier */
 211
 212/*
 213 * Segmentation buffer descriptor
 214 */
 215
 216#define MID_SEG_COUNT           MID_RED_COUNT
 217#define MID_SEG_RATE            0x01f80000
 218#define MID_SEG_RATE_SHIFT      19
 219#define MID_SEG_PR              0x06000000
 220#define MID_SEG_PR_SHIFT        25
 221#define MID_SEG_AAL5            0x08000000
 222#define MID_SEG_ID              0xf0000000
 223#define MID_SEG_ID_SHIFT        28
 224#define MID_SEG_MAX_RATE        63
 225
 226#define MID_SEG_CLP             0x00000001
 227#define MID_SEG_PTI             0x0000000e
 228#define MID_SEG_PTI_SHIFT       1
 229#define MID_SEG_VCI             0x00003ff0
 230#define MID_SEG_VCI_SHIFT       4
 231
 232#define MID_SEG_TX_ID           0xb             /* constant identifier */
 233
 234/*
 235 * DMA entry
 236 */
 237
 238#define MID_DMA_COUNT           0xffff0000
 239#define MID_DMA_COUNT_SHIFT     16
 240#define MID_DMA_END             0x00000020
 241#define MID_DMA_TYPE            0x0000000f
 242
 243#define MID_DT_JK       0x3
 244#define MID_DT_WORD     0x0
 245#define MID_DT_2W       0x7
 246#define MID_DT_4W       0x4
 247#define MID_DT_8W       0x5
 248#define MID_DT_16W      0x6
 249#define MID_DT_2WM      0xf
 250#define MID_DT_4WM      0xc
 251#define MID_DT_8WM      0xd
 252#define MID_DT_16WM     0xe
 253
 254/* only for RX*/
 255#define MID_DMA_VCI             0x0000ffc0
 256#define MID_DMA_VCI_SHIFT       6
 257
 258/* only for TX */
 259#define MID_DMA_CHAN            0x000001c0
 260#define MID_DMA_CHAN_SHIFT      6
 261
 262#define MID_DT_BYTE     0x1
 263#define MID_DT_HWORD    0x2
 264
 265#endif
 266