linux/drivers/media/i2c/soc_camera/rj54n1cb0c.c
<<
>>
Prefs
   1/*
   2 * Driver for RJ54N1CB0C CMOS Image Sensor from Sharp
   3 *
   4 * Copyright (C) 2009, Guennadi Liakhovetski <g.liakhovetski@gmx.de>
   5 *
   6 * This program is free software; you can redistribute it and/or modify
   7 * it under the terms of the GNU General Public License version 2 as
   8 * published by the Free Software Foundation.
   9 */
  10
  11#include <linux/delay.h>
  12#include <linux/i2c.h>
  13#include <linux/slab.h>
  14#include <linux/v4l2-mediabus.h>
  15#include <linux/videodev2.h>
  16#include <linux/module.h>
  17
  18#include <media/rj54n1cb0c.h>
  19#include <media/soc_camera.h>
  20#include <media/v4l2-clk.h>
  21#include <media/v4l2-subdev.h>
  22#include <media/v4l2-ctrls.h>
  23
  24#define RJ54N1_DEV_CODE                 0x0400
  25#define RJ54N1_DEV_CODE2                0x0401
  26#define RJ54N1_OUT_SEL                  0x0403
  27#define RJ54N1_XY_OUTPUT_SIZE_S_H       0x0404
  28#define RJ54N1_X_OUTPUT_SIZE_S_L        0x0405
  29#define RJ54N1_Y_OUTPUT_SIZE_S_L        0x0406
  30#define RJ54N1_XY_OUTPUT_SIZE_P_H       0x0407
  31#define RJ54N1_X_OUTPUT_SIZE_P_L        0x0408
  32#define RJ54N1_Y_OUTPUT_SIZE_P_L        0x0409
  33#define RJ54N1_LINE_LENGTH_PCK_S_H      0x040a
  34#define RJ54N1_LINE_LENGTH_PCK_S_L      0x040b
  35#define RJ54N1_LINE_LENGTH_PCK_P_H      0x040c
  36#define RJ54N1_LINE_LENGTH_PCK_P_L      0x040d
  37#define RJ54N1_RESIZE_N                 0x040e
  38#define RJ54N1_RESIZE_N_STEP            0x040f
  39#define RJ54N1_RESIZE_STEP              0x0410
  40#define RJ54N1_RESIZE_HOLD_H            0x0411
  41#define RJ54N1_RESIZE_HOLD_L            0x0412
  42#define RJ54N1_H_OBEN_OFS               0x0413
  43#define RJ54N1_V_OBEN_OFS               0x0414
  44#define RJ54N1_RESIZE_CONTROL           0x0415
  45#define RJ54N1_STILL_CONTROL            0x0417
  46#define RJ54N1_INC_USE_SEL_H            0x0425
  47#define RJ54N1_INC_USE_SEL_L            0x0426
  48#define RJ54N1_MIRROR_STILL_MODE        0x0427
  49#define RJ54N1_INIT_START               0x0428
  50#define RJ54N1_SCALE_1_2_LEV            0x0429
  51#define RJ54N1_SCALE_4_LEV              0x042a
  52#define RJ54N1_Y_GAIN                   0x04d8
  53#define RJ54N1_APT_GAIN_UP              0x04fa
  54#define RJ54N1_RA_SEL_UL                0x0530
  55#define RJ54N1_BYTE_SWAP                0x0531
  56#define RJ54N1_OUT_SIGPO                0x053b
  57#define RJ54N1_WB_SEL_WEIGHT_I          0x054e
  58#define RJ54N1_BIT8_WB                  0x0569
  59#define RJ54N1_HCAPS_WB                 0x056a
  60#define RJ54N1_VCAPS_WB                 0x056b
  61#define RJ54N1_HCAPE_WB                 0x056c
  62#define RJ54N1_VCAPE_WB                 0x056d
  63#define RJ54N1_EXPOSURE_CONTROL         0x058c
  64#define RJ54N1_FRAME_LENGTH_S_H         0x0595
  65#define RJ54N1_FRAME_LENGTH_S_L         0x0596
  66#define RJ54N1_FRAME_LENGTH_P_H         0x0597
  67#define RJ54N1_FRAME_LENGTH_P_L         0x0598
  68#define RJ54N1_PEAK_H                   0x05b7
  69#define RJ54N1_PEAK_50                  0x05b8
  70#define RJ54N1_PEAK_60                  0x05b9
  71#define RJ54N1_PEAK_DIFF                0x05ba
  72#define RJ54N1_IOC                      0x05ef
  73#define RJ54N1_TG_BYPASS                0x0700
  74#define RJ54N1_PLL_L                    0x0701
  75#define RJ54N1_PLL_N                    0x0702
  76#define RJ54N1_PLL_EN                   0x0704
  77#define RJ54N1_RATIO_TG                 0x0706
  78#define RJ54N1_RATIO_T                  0x0707
  79#define RJ54N1_RATIO_R                  0x0708
  80#define RJ54N1_RAMP_TGCLK_EN            0x0709
  81#define RJ54N1_OCLK_DSP                 0x0710
  82#define RJ54N1_RATIO_OP                 0x0711
  83#define RJ54N1_RATIO_O                  0x0712
  84#define RJ54N1_OCLK_SEL_EN              0x0713
  85#define RJ54N1_CLK_RST                  0x0717
  86#define RJ54N1_RESET_STANDBY            0x0718
  87#define RJ54N1_FWFLG                    0x07fe
  88
  89#define E_EXCLK                         (1 << 7)
  90#define SOFT_STDBY                      (1 << 4)
  91#define SEN_RSTX                        (1 << 2)
  92#define TG_RSTX                         (1 << 1)
  93#define DSP_RSTX                        (1 << 0)
  94
  95#define RESIZE_HOLD_SEL                 (1 << 2)
  96#define RESIZE_GO                       (1 << 1)
  97
  98/*
  99 * When cropping, the camera automatically centers the cropped region, there
 100 * doesn't seem to be a way to specify an explicit location of the rectangle.
 101 */
 102#define RJ54N1_COLUMN_SKIP              0
 103#define RJ54N1_ROW_SKIP                 0
 104#define RJ54N1_MAX_WIDTH                1600
 105#define RJ54N1_MAX_HEIGHT               1200
 106
 107#define PLL_L                           2
 108#define PLL_N                           0x31
 109
 110/* I2C addresses: 0x50, 0x51, 0x60, 0x61 */
 111
 112/* RJ54N1CB0C has only one fixed colorspace per pixelcode */
 113struct rj54n1_datafmt {
 114        enum v4l2_mbus_pixelcode        code;
 115        enum v4l2_colorspace            colorspace;
 116};
 117
 118/* Find a data format by a pixel code in an array */
 119static const struct rj54n1_datafmt *rj54n1_find_datafmt(
 120        enum v4l2_mbus_pixelcode code, const struct rj54n1_datafmt *fmt,
 121        int n)
 122{
 123        int i;
 124        for (i = 0; i < n; i++)
 125                if (fmt[i].code == code)
 126                        return fmt + i;
 127
 128        return NULL;
 129}
 130
 131static const struct rj54n1_datafmt rj54n1_colour_fmts[] = {
 132        {V4L2_MBUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG},
 133        {V4L2_MBUS_FMT_YVYU8_2X8, V4L2_COLORSPACE_JPEG},
 134        {V4L2_MBUS_FMT_RGB565_2X8_LE, V4L2_COLORSPACE_SRGB},
 135        {V4L2_MBUS_FMT_RGB565_2X8_BE, V4L2_COLORSPACE_SRGB},
 136        {V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_LE, V4L2_COLORSPACE_SRGB},
 137        {V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_LE, V4L2_COLORSPACE_SRGB},
 138        {V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_BE, V4L2_COLORSPACE_SRGB},
 139        {V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_BE, V4L2_COLORSPACE_SRGB},
 140        {V4L2_MBUS_FMT_SBGGR10_1X10, V4L2_COLORSPACE_SRGB},
 141};
 142
 143struct rj54n1_clock_div {
 144        u8 ratio_tg;    /* can be 0 or an odd number */
 145        u8 ratio_t;
 146        u8 ratio_r;
 147        u8 ratio_op;
 148        u8 ratio_o;
 149};
 150
 151struct rj54n1 {
 152        struct v4l2_subdev subdev;
 153        struct v4l2_ctrl_handler hdl;
 154        struct v4l2_clk *clk;
 155        struct rj54n1_clock_div clk_div;
 156        const struct rj54n1_datafmt *fmt;
 157        struct v4l2_rect rect;  /* Sensor window */
 158        unsigned int tgclk_mhz;
 159        bool auto_wb;
 160        unsigned short width;   /* Output window */
 161        unsigned short height;
 162        unsigned short resize;  /* Sensor * 1024 / resize = Output */
 163        unsigned short scale;
 164        u8 bank;
 165};
 166
 167struct rj54n1_reg_val {
 168        u16 reg;
 169        u8 val;
 170};
 171
 172static const struct rj54n1_reg_val bank_4[] = {
 173        {0x417, 0},
 174        {0x42c, 0},
 175        {0x42d, 0xf0},
 176        {0x42e, 0},
 177        {0x42f, 0x50},
 178        {0x430, 0xf5},
 179        {0x431, 0x16},
 180        {0x432, 0x20},
 181        {0x433, 0},
 182        {0x434, 0xc8},
 183        {0x43c, 8},
 184        {0x43e, 0x90},
 185        {0x445, 0x83},
 186        {0x4ba, 0x58},
 187        {0x4bb, 4},
 188        {0x4bc, 0x20},
 189        {0x4db, 4},
 190        {0x4fe, 2},
 191};
 192
 193static const struct rj54n1_reg_val bank_5[] = {
 194        {0x514, 0},
 195        {0x516, 0},
 196        {0x518, 0},
 197        {0x51a, 0},
 198        {0x51d, 0xff},
 199        {0x56f, 0x28},
 200        {0x575, 0x40},
 201        {0x5bc, 0x48},
 202        {0x5c1, 6},
 203        {0x5e5, 0x11},
 204        {0x5e6, 0x43},
 205        {0x5e7, 0x33},
 206        {0x5e8, 0x21},
 207        {0x5e9, 0x30},
 208        {0x5ea, 0x0},
 209        {0x5eb, 0xa5},
 210        {0x5ec, 0xff},
 211        {0x5fe, 2},
 212};
 213
 214static const struct rj54n1_reg_val bank_7[] = {
 215        {0x70a, 0},
 216        {0x714, 0xff},
 217        {0x715, 0xff},
 218        {0x716, 0x1f},
 219        {0x7FE, 2},
 220};
 221
 222static const struct rj54n1_reg_val bank_8[] = {
 223        {0x800, 0x00},
 224        {0x801, 0x01},
 225        {0x802, 0x61},
 226        {0x805, 0x00},
 227        {0x806, 0x00},
 228        {0x807, 0x00},
 229        {0x808, 0x00},
 230        {0x809, 0x01},
 231        {0x80A, 0x61},
 232        {0x80B, 0x00},
 233        {0x80C, 0x01},
 234        {0x80D, 0x00},
 235        {0x80E, 0x00},
 236        {0x80F, 0x00},
 237        {0x810, 0x00},
 238        {0x811, 0x01},
 239        {0x812, 0x61},
 240        {0x813, 0x00},
 241        {0x814, 0x11},
 242        {0x815, 0x00},
 243        {0x816, 0x41},
 244        {0x817, 0x00},
 245        {0x818, 0x51},
 246        {0x819, 0x01},
 247        {0x81A, 0x1F},
 248        {0x81B, 0x00},
 249        {0x81C, 0x01},
 250        {0x81D, 0x00},
 251        {0x81E, 0x11},
 252        {0x81F, 0x00},
 253        {0x820, 0x41},
 254        {0x821, 0x00},
 255        {0x822, 0x51},
 256        {0x823, 0x00},
 257        {0x824, 0x00},
 258        {0x825, 0x00},
 259        {0x826, 0x47},
 260        {0x827, 0x01},
 261        {0x828, 0x4F},
 262        {0x829, 0x00},
 263        {0x82A, 0x00},
 264        {0x82B, 0x00},
 265        {0x82C, 0x30},
 266        {0x82D, 0x00},
 267        {0x82E, 0x40},
 268        {0x82F, 0x00},
 269        {0x830, 0xB3},
 270        {0x831, 0x00},
 271        {0x832, 0xE3},
 272        {0x833, 0x00},
 273        {0x834, 0x00},
 274        {0x835, 0x00},
 275        {0x836, 0x00},
 276        {0x837, 0x00},
 277        {0x838, 0x00},
 278        {0x839, 0x01},
 279        {0x83A, 0x61},
 280        {0x83B, 0x00},
 281        {0x83C, 0x01},
 282        {0x83D, 0x00},
 283        {0x83E, 0x00},
 284        {0x83F, 0x00},
 285        {0x840, 0x00},
 286        {0x841, 0x01},
 287        {0x842, 0x61},
 288        {0x843, 0x00},
 289        {0x844, 0x1D},
 290        {0x845, 0x00},
 291        {0x846, 0x00},
 292        {0x847, 0x00},
 293        {0x848, 0x00},
 294        {0x849, 0x01},
 295        {0x84A, 0x1F},
 296        {0x84B, 0x00},
 297        {0x84C, 0x05},
 298        {0x84D, 0x00},
 299        {0x84E, 0x19},
 300        {0x84F, 0x01},
 301        {0x850, 0x21},
 302        {0x851, 0x01},
 303        {0x852, 0x5D},
 304        {0x853, 0x00},
 305        {0x854, 0x00},
 306        {0x855, 0x00},
 307        {0x856, 0x19},
 308        {0x857, 0x01},
 309        {0x858, 0x21},
 310        {0x859, 0x00},
 311        {0x85A, 0x00},
 312        {0x85B, 0x00},
 313        {0x85C, 0x00},
 314        {0x85D, 0x00},
 315        {0x85E, 0x00},
 316        {0x85F, 0x00},
 317        {0x860, 0xB3},
 318        {0x861, 0x00},
 319        {0x862, 0xE3},
 320        {0x863, 0x00},
 321        {0x864, 0x00},
 322        {0x865, 0x00},
 323        {0x866, 0x00},
 324        {0x867, 0x00},
 325        {0x868, 0x00},
 326        {0x869, 0xE2},
 327        {0x86A, 0x00},
 328        {0x86B, 0x01},
 329        {0x86C, 0x06},
 330        {0x86D, 0x00},
 331        {0x86E, 0x00},
 332        {0x86F, 0x00},
 333        {0x870, 0x60},
 334        {0x871, 0x8C},
 335        {0x872, 0x10},
 336        {0x873, 0x00},
 337        {0x874, 0xE0},
 338        {0x875, 0x00},
 339        {0x876, 0x27},
 340        {0x877, 0x01},
 341        {0x878, 0x00},
 342        {0x879, 0x00},
 343        {0x87A, 0x00},
 344        {0x87B, 0x03},
 345        {0x87C, 0x00},
 346        {0x87D, 0x00},
 347        {0x87E, 0x00},
 348        {0x87F, 0x00},
 349        {0x880, 0x00},
 350        {0x881, 0x00},
 351        {0x882, 0x00},
 352        {0x883, 0x00},
 353        {0x884, 0x00},
 354        {0x885, 0x00},
 355        {0x886, 0xF8},
 356        {0x887, 0x00},
 357        {0x888, 0x03},
 358        {0x889, 0x00},
 359        {0x88A, 0x64},
 360        {0x88B, 0x00},
 361        {0x88C, 0x03},
 362        {0x88D, 0x00},
 363        {0x88E, 0xB1},
 364        {0x88F, 0x00},
 365        {0x890, 0x03},
 366        {0x891, 0x01},
 367        {0x892, 0x1D},
 368        {0x893, 0x00},
 369        {0x894, 0x03},
 370        {0x895, 0x01},
 371        {0x896, 0x4B},
 372        {0x897, 0x00},
 373        {0x898, 0xE5},
 374        {0x899, 0x00},
 375        {0x89A, 0x01},
 376        {0x89B, 0x00},
 377        {0x89C, 0x01},
 378        {0x89D, 0x04},
 379        {0x89E, 0xC8},
 380        {0x89F, 0x00},
 381        {0x8A0, 0x01},
 382        {0x8A1, 0x01},
 383        {0x8A2, 0x61},
 384        {0x8A3, 0x00},
 385        {0x8A4, 0x01},
 386        {0x8A5, 0x00},
 387        {0x8A6, 0x00},
 388        {0x8A7, 0x00},
 389        {0x8A8, 0x00},
 390        {0x8A9, 0x00},
 391        {0x8AA, 0x7F},
 392        {0x8AB, 0x03},
 393        {0x8AC, 0x00},
 394        {0x8AD, 0x00},
 395        {0x8AE, 0x00},
 396        {0x8AF, 0x00},
 397        {0x8B0, 0x00},
 398        {0x8B1, 0x00},
 399        {0x8B6, 0x00},
 400        {0x8B7, 0x01},
 401        {0x8B8, 0x00},
 402        {0x8B9, 0x00},
 403        {0x8BA, 0x02},
 404        {0x8BB, 0x00},
 405        {0x8BC, 0xFF},
 406        {0x8BD, 0x00},
 407        {0x8FE, 2},
 408};
 409
 410static const struct rj54n1_reg_val bank_10[] = {
 411        {0x10bf, 0x69}
 412};
 413
 414/* Clock dividers - these are default register values, divider = register + 1 */
 415static const struct rj54n1_clock_div clk_div = {
 416        .ratio_tg       = 3 /* default: 5 */,
 417        .ratio_t        = 4 /* default: 1 */,
 418        .ratio_r        = 4 /* default: 0 */,
 419        .ratio_op       = 1 /* default: 5 */,
 420        .ratio_o        = 9 /* default: 0 */,
 421};
 422
 423static struct rj54n1 *to_rj54n1(const struct i2c_client *client)
 424{
 425        return container_of(i2c_get_clientdata(client), struct rj54n1, subdev);
 426}
 427
 428static int reg_read(struct i2c_client *client, const u16 reg)
 429{
 430        struct rj54n1 *rj54n1 = to_rj54n1(client);
 431        int ret;
 432
 433        /* set bank */
 434        if (rj54n1->bank != reg >> 8) {
 435                dev_dbg(&client->dev, "[0x%x] = 0x%x\n", 0xff, reg >> 8);
 436                ret = i2c_smbus_write_byte_data(client, 0xff, reg >> 8);
 437                if (ret < 0)
 438                        return ret;
 439                rj54n1->bank = reg >> 8;
 440        }
 441        return i2c_smbus_read_byte_data(client, reg & 0xff);
 442}
 443
 444static int reg_write(struct i2c_client *client, const u16 reg,
 445                     const u8 data)
 446{
 447        struct rj54n1 *rj54n1 = to_rj54n1(client);
 448        int ret;
 449
 450        /* set bank */
 451        if (rj54n1->bank != reg >> 8) {
 452                dev_dbg(&client->dev, "[0x%x] = 0x%x\n", 0xff, reg >> 8);
 453                ret = i2c_smbus_write_byte_data(client, 0xff, reg >> 8);
 454                if (ret < 0)
 455                        return ret;
 456                rj54n1->bank = reg >> 8;
 457        }
 458        dev_dbg(&client->dev, "[0x%x] = 0x%x\n", reg & 0xff, data);
 459        return i2c_smbus_write_byte_data(client, reg & 0xff, data);
 460}
 461
 462static int reg_set(struct i2c_client *client, const u16 reg,
 463                   const u8 data, const u8 mask)
 464{
 465        int ret;
 466
 467        ret = reg_read(client, reg);
 468        if (ret < 0)
 469                return ret;
 470        return reg_write(client, reg, (ret & ~mask) | (data & mask));
 471}
 472
 473static int reg_write_multiple(struct i2c_client *client,
 474                              const struct rj54n1_reg_val *rv, const int n)
 475{
 476        int i, ret;
 477
 478        for (i = 0; i < n; i++) {
 479                ret = reg_write(client, rv->reg, rv->val);
 480                if (ret < 0)
 481                        return ret;
 482                rv++;
 483        }
 484
 485        return 0;
 486}
 487
 488static int rj54n1_enum_fmt(struct v4l2_subdev *sd, unsigned int index,
 489                           enum v4l2_mbus_pixelcode *code)
 490{
 491        if (index >= ARRAY_SIZE(rj54n1_colour_fmts))
 492                return -EINVAL;
 493
 494        *code = rj54n1_colour_fmts[index].code;
 495        return 0;
 496}
 497
 498static int rj54n1_s_stream(struct v4l2_subdev *sd, int enable)
 499{
 500        struct i2c_client *client = v4l2_get_subdevdata(sd);
 501
 502        /* Switch between preview and still shot modes */
 503        return reg_set(client, RJ54N1_STILL_CONTROL, (!enable) << 7, 0x80);
 504}
 505
 506static int rj54n1_set_rect(struct i2c_client *client,
 507                           u16 reg_x, u16 reg_y, u16 reg_xy,
 508                           u32 width, u32 height)
 509{
 510        int ret;
 511
 512        ret = reg_write(client, reg_xy,
 513                        ((width >> 4) & 0x70) |
 514                        ((height >> 8) & 7));
 515
 516        if (!ret)
 517                ret = reg_write(client, reg_x, width & 0xff);
 518        if (!ret)
 519                ret = reg_write(client, reg_y, height & 0xff);
 520
 521        return ret;
 522}
 523
 524/*
 525 * Some commands, specifically certain initialisation sequences, require
 526 * a commit operation.
 527 */
 528static int rj54n1_commit(struct i2c_client *client)
 529{
 530        int ret = reg_write(client, RJ54N1_INIT_START, 1);
 531        msleep(10);
 532        if (!ret)
 533                ret = reg_write(client, RJ54N1_INIT_START, 0);
 534        return ret;
 535}
 536
 537static int rj54n1_sensor_scale(struct v4l2_subdev *sd, s32 *in_w, s32 *in_h,
 538                               s32 *out_w, s32 *out_h);
 539
 540static int rj54n1_s_crop(struct v4l2_subdev *sd, const struct v4l2_crop *a)
 541{
 542        struct i2c_client *client = v4l2_get_subdevdata(sd);
 543        struct rj54n1 *rj54n1 = to_rj54n1(client);
 544        const struct v4l2_rect *rect = &a->c;
 545        int dummy = 0, output_w, output_h,
 546                input_w = rect->width, input_h = rect->height;
 547        int ret;
 548
 549        /* arbitrary minimum width and height, edges unimportant */
 550        soc_camera_limit_side(&dummy, &input_w,
 551                     RJ54N1_COLUMN_SKIP, 8, RJ54N1_MAX_WIDTH);
 552
 553        soc_camera_limit_side(&dummy, &input_h,
 554                     RJ54N1_ROW_SKIP, 8, RJ54N1_MAX_HEIGHT);
 555
 556        output_w = (input_w * 1024 + rj54n1->resize / 2) / rj54n1->resize;
 557        output_h = (input_h * 1024 + rj54n1->resize / 2) / rj54n1->resize;
 558
 559        dev_dbg(&client->dev, "Scaling for %dx%d : %u = %dx%d\n",
 560                input_w, input_h, rj54n1->resize, output_w, output_h);
 561
 562        ret = rj54n1_sensor_scale(sd, &input_w, &input_h, &output_w, &output_h);
 563        if (ret < 0)
 564                return ret;
 565
 566        rj54n1->width           = output_w;
 567        rj54n1->height          = output_h;
 568        rj54n1->resize          = ret;
 569        rj54n1->rect.width      = input_w;
 570        rj54n1->rect.height     = input_h;
 571
 572        return 0;
 573}
 574
 575static int rj54n1_g_crop(struct v4l2_subdev *sd, struct v4l2_crop *a)
 576{
 577        struct i2c_client *client = v4l2_get_subdevdata(sd);
 578        struct rj54n1 *rj54n1 = to_rj54n1(client);
 579
 580        a->c    = rj54n1->rect;
 581        a->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
 582
 583        return 0;
 584}
 585
 586static int rj54n1_cropcap(struct v4l2_subdev *sd, struct v4l2_cropcap *a)
 587{
 588        a->bounds.left                  = RJ54N1_COLUMN_SKIP;
 589        a->bounds.top                   = RJ54N1_ROW_SKIP;
 590        a->bounds.width                 = RJ54N1_MAX_WIDTH;
 591        a->bounds.height                = RJ54N1_MAX_HEIGHT;
 592        a->defrect                      = a->bounds;
 593        a->type                         = V4L2_BUF_TYPE_VIDEO_CAPTURE;
 594        a->pixelaspect.numerator        = 1;
 595        a->pixelaspect.denominator      = 1;
 596
 597        return 0;
 598}
 599
 600static int rj54n1_g_fmt(struct v4l2_subdev *sd,
 601                        struct v4l2_mbus_framefmt *mf)
 602{
 603        struct i2c_client *client = v4l2_get_subdevdata(sd);
 604        struct rj54n1 *rj54n1 = to_rj54n1(client);
 605
 606        mf->code        = rj54n1->fmt->code;
 607        mf->colorspace  = rj54n1->fmt->colorspace;
 608        mf->field       = V4L2_FIELD_NONE;
 609        mf->width       = rj54n1->width;
 610        mf->height      = rj54n1->height;
 611
 612        return 0;
 613}
 614
 615/*
 616 * The actual geometry configuration routine. It scales the input window into
 617 * the output one, updates the window sizes and returns an error or the resize
 618 * coefficient on success. Note: we only use the "Fixed Scaling" on this camera.
 619 */
 620static int rj54n1_sensor_scale(struct v4l2_subdev *sd, s32 *in_w, s32 *in_h,
 621                               s32 *out_w, s32 *out_h)
 622{
 623        struct i2c_client *client = v4l2_get_subdevdata(sd);
 624        struct rj54n1 *rj54n1 = to_rj54n1(client);
 625        unsigned int skip, resize, input_w = *in_w, input_h = *in_h,
 626                output_w = *out_w, output_h = *out_h;
 627        u16 inc_sel, wb_bit8, wb_left, wb_right, wb_top, wb_bottom;
 628        unsigned int peak, peak_50, peak_60;
 629        int ret;
 630
 631        /*
 632         * We have a problem with crops, where the window is larger than 512x384
 633         * and output window is larger than a half of the input one. In this
 634         * case we have to either reduce the input window to equal or below
 635         * 512x384 or the output window to equal or below 1/2 of the input.
 636         */
 637        if (output_w > max(512U, input_w / 2)) {
 638                if (2 * output_w > RJ54N1_MAX_WIDTH) {
 639                        input_w = RJ54N1_MAX_WIDTH;
 640                        output_w = RJ54N1_MAX_WIDTH / 2;
 641                } else {
 642                        input_w = output_w * 2;
 643                }
 644
 645                dev_dbg(&client->dev, "Adjusted output width: in %u, out %u\n",
 646                        input_w, output_w);
 647        }
 648
 649        if (output_h > max(384U, input_h / 2)) {
 650                if (2 * output_h > RJ54N1_MAX_HEIGHT) {
 651                        input_h = RJ54N1_MAX_HEIGHT;
 652                        output_h = RJ54N1_MAX_HEIGHT / 2;
 653                } else {
 654                        input_h = output_h * 2;
 655                }
 656
 657                dev_dbg(&client->dev, "Adjusted output height: in %u, out %u\n",
 658                        input_h, output_h);
 659        }
 660
 661        /* Idea: use the read mode for snapshots, handle separate geometries */
 662        ret = rj54n1_set_rect(client, RJ54N1_X_OUTPUT_SIZE_S_L,
 663                              RJ54N1_Y_OUTPUT_SIZE_S_L,
 664                              RJ54N1_XY_OUTPUT_SIZE_S_H, output_w, output_h);
 665        if (!ret)
 666                ret = rj54n1_set_rect(client, RJ54N1_X_OUTPUT_SIZE_P_L,
 667                              RJ54N1_Y_OUTPUT_SIZE_P_L,
 668                              RJ54N1_XY_OUTPUT_SIZE_P_H, output_w, output_h);
 669
 670        if (ret < 0)
 671                return ret;
 672
 673        if (output_w > input_w && output_h > input_h) {
 674                input_w = output_w;
 675                input_h = output_h;
 676
 677                resize = 1024;
 678        } else {
 679                unsigned int resize_x, resize_y;
 680                resize_x = (input_w * 1024 + output_w / 2) / output_w;
 681                resize_y = (input_h * 1024 + output_h / 2) / output_h;
 682
 683                /* We want max(resize_x, resize_y), check if it still fits */
 684                if (resize_x > resize_y &&
 685                    (output_h * resize_x + 512) / 1024 > RJ54N1_MAX_HEIGHT)
 686                        resize = (RJ54N1_MAX_HEIGHT * 1024 + output_h / 2) /
 687                                output_h;
 688                else if (resize_y > resize_x &&
 689                         (output_w * resize_y + 512) / 1024 > RJ54N1_MAX_WIDTH)
 690                        resize = (RJ54N1_MAX_WIDTH * 1024 + output_w / 2) /
 691                                output_w;
 692                else
 693                        resize = max(resize_x, resize_y);
 694
 695                /* Prohibited value ranges */
 696                switch (resize) {
 697                case 2040 ... 2047:
 698                        resize = 2039;
 699                        break;
 700                case 4080 ... 4095:
 701                        resize = 4079;
 702                        break;
 703                case 8160 ... 8191:
 704                        resize = 8159;
 705                        break;
 706                case 16320 ... 16384:
 707                        resize = 16319;
 708                }
 709        }
 710
 711        /* Set scaling */
 712        ret = reg_write(client, RJ54N1_RESIZE_HOLD_L, resize & 0xff);
 713        if (!ret)
 714                ret = reg_write(client, RJ54N1_RESIZE_HOLD_H, resize >> 8);
 715
 716        if (ret < 0)
 717                return ret;
 718
 719        /*
 720         * Configure a skipping bitmask. The sensor will select a skipping value
 721         * among set bits automatically. This is very unclear in the datasheet
 722         * too. I was told, in this register one enables all skipping values,
 723         * that are required for a specific resize, and the camera selects
 724         * automatically, which ones to use. But it is unclear how to identify,
 725         * which cropping values are needed. Secondly, why don't we just set all
 726         * bits and let the camera choose? Would it increase processing time and
 727         * reduce the framerate? Using 0xfffc for INC_USE_SEL doesn't seem to
 728         * improve the image quality or stability for larger frames (see comment
 729         * above), but I didn't check the framerate.
 730         */
 731        skip = min(resize / 1024, 15U);
 732
 733        inc_sel = 1 << skip;
 734
 735        if (inc_sel <= 2)
 736                inc_sel = 0xc;
 737        else if (resize & 1023 && skip < 15)
 738                inc_sel |= 1 << (skip + 1);
 739
 740        ret = reg_write(client, RJ54N1_INC_USE_SEL_L, inc_sel & 0xfc);
 741        if (!ret)
 742                ret = reg_write(client, RJ54N1_INC_USE_SEL_H, inc_sel >> 8);
 743
 744        if (!rj54n1->auto_wb) {
 745                /* Auto white balance window */
 746                wb_left   = output_w / 16;
 747                wb_right  = (3 * output_w / 4 - 3) / 4;
 748                wb_top    = output_h / 16;
 749                wb_bottom = (3 * output_h / 4 - 3) / 4;
 750                wb_bit8   = ((wb_left >> 2) & 0x40) | ((wb_top >> 4) & 0x10) |
 751                        ((wb_right >> 6) & 4) | ((wb_bottom >> 8) & 1);
 752
 753                if (!ret)
 754                        ret = reg_write(client, RJ54N1_BIT8_WB, wb_bit8);
 755                if (!ret)
 756                        ret = reg_write(client, RJ54N1_HCAPS_WB, wb_left);
 757                if (!ret)
 758                        ret = reg_write(client, RJ54N1_VCAPS_WB, wb_top);
 759                if (!ret)
 760                        ret = reg_write(client, RJ54N1_HCAPE_WB, wb_right);
 761                if (!ret)
 762                        ret = reg_write(client, RJ54N1_VCAPE_WB, wb_bottom);
 763        }
 764
 765        /* Antiflicker */
 766        peak = 12 * RJ54N1_MAX_WIDTH * (1 << 14) * resize / rj54n1->tgclk_mhz /
 767                10000;
 768        peak_50 = peak / 6;
 769        peak_60 = peak / 5;
 770
 771        if (!ret)
 772                ret = reg_write(client, RJ54N1_PEAK_H,
 773                                ((peak_50 >> 4) & 0xf0) | (peak_60 >> 8));
 774        if (!ret)
 775                ret = reg_write(client, RJ54N1_PEAK_50, peak_50);
 776        if (!ret)
 777                ret = reg_write(client, RJ54N1_PEAK_60, peak_60);
 778        if (!ret)
 779                ret = reg_write(client, RJ54N1_PEAK_DIFF, peak / 150);
 780
 781        /* Start resizing */
 782        if (!ret)
 783                ret = reg_write(client, RJ54N1_RESIZE_CONTROL,
 784                                RESIZE_HOLD_SEL | RESIZE_GO | 1);
 785
 786        if (ret < 0)
 787                return ret;
 788
 789        /* Constant taken from manufacturer's example */
 790        msleep(230);
 791
 792        ret = reg_write(client, RJ54N1_RESIZE_CONTROL, RESIZE_HOLD_SEL | 1);
 793        if (ret < 0)
 794                return ret;
 795
 796        *in_w = (output_w * resize + 512) / 1024;
 797        *in_h = (output_h * resize + 512) / 1024;
 798        *out_w = output_w;
 799        *out_h = output_h;
 800
 801        dev_dbg(&client->dev, "Scaled for %dx%d : %u = %ux%u, skip %u\n",
 802                *in_w, *in_h, resize, output_w, output_h, skip);
 803
 804        return resize;
 805}
 806
 807static int rj54n1_set_clock(struct i2c_client *client)
 808{
 809        struct rj54n1 *rj54n1 = to_rj54n1(client);
 810        int ret;
 811
 812        /* Enable external clock */
 813        ret = reg_write(client, RJ54N1_RESET_STANDBY, E_EXCLK | SOFT_STDBY);
 814        /* Leave stand-by. Note: use this when implementing suspend / resume */
 815        if (!ret)
 816                ret = reg_write(client, RJ54N1_RESET_STANDBY, E_EXCLK);
 817
 818        if (!ret)
 819                ret = reg_write(client, RJ54N1_PLL_L, PLL_L);
 820        if (!ret)
 821                ret = reg_write(client, RJ54N1_PLL_N, PLL_N);
 822
 823        /* TGCLK dividers */
 824        if (!ret)
 825                ret = reg_write(client, RJ54N1_RATIO_TG,
 826                                rj54n1->clk_div.ratio_tg);
 827        if (!ret)
 828                ret = reg_write(client, RJ54N1_RATIO_T,
 829                                rj54n1->clk_div.ratio_t);
 830        if (!ret)
 831                ret = reg_write(client, RJ54N1_RATIO_R,
 832                                rj54n1->clk_div.ratio_r);
 833
 834        /* Enable TGCLK & RAMP */
 835        if (!ret)
 836                ret = reg_write(client, RJ54N1_RAMP_TGCLK_EN, 3);
 837
 838        /* Disable clock output */
 839        if (!ret)
 840                ret = reg_write(client, RJ54N1_OCLK_DSP, 0);
 841
 842        /* Set divisors */
 843        if (!ret)
 844                ret = reg_write(client, RJ54N1_RATIO_OP,
 845                                rj54n1->clk_div.ratio_op);
 846        if (!ret)
 847                ret = reg_write(client, RJ54N1_RATIO_O,
 848                                rj54n1->clk_div.ratio_o);
 849
 850        /* Enable OCLK */
 851        if (!ret)
 852                ret = reg_write(client, RJ54N1_OCLK_SEL_EN, 1);
 853
 854        /* Use PLL for Timing Generator, write 2 to reserved bits */
 855        if (!ret)
 856                ret = reg_write(client, RJ54N1_TG_BYPASS, 2);
 857
 858        /* Take sensor out of reset */
 859        if (!ret)
 860                ret = reg_write(client, RJ54N1_RESET_STANDBY,
 861                                E_EXCLK | SEN_RSTX);
 862        /* Enable PLL */
 863        if (!ret)
 864                ret = reg_write(client, RJ54N1_PLL_EN, 1);
 865
 866        /* Wait for PLL to stabilise */
 867        msleep(10);
 868
 869        /* Enable clock to frequency divider */
 870        if (!ret)
 871                ret = reg_write(client, RJ54N1_CLK_RST, 1);
 872
 873        if (!ret)
 874                ret = reg_read(client, RJ54N1_CLK_RST);
 875        if (ret != 1) {
 876                dev_err(&client->dev,
 877                        "Resetting RJ54N1CB0C clock failed: %d!\n", ret);
 878                return -EIO;
 879        }
 880
 881        /* Start the PLL */
 882        ret = reg_set(client, RJ54N1_OCLK_DSP, 1, 1);
 883
 884        /* Enable OCLK */
 885        if (!ret)
 886                ret = reg_write(client, RJ54N1_OCLK_SEL_EN, 1);
 887
 888        return ret;
 889}
 890
 891static int rj54n1_reg_init(struct i2c_client *client)
 892{
 893        struct rj54n1 *rj54n1 = to_rj54n1(client);
 894        int ret = rj54n1_set_clock(client);
 895
 896        if (!ret)
 897                ret = reg_write_multiple(client, bank_7, ARRAY_SIZE(bank_7));
 898        if (!ret)
 899                ret = reg_write_multiple(client, bank_10, ARRAY_SIZE(bank_10));
 900
 901        /* Set binning divisors */
 902        if (!ret)
 903                ret = reg_write(client, RJ54N1_SCALE_1_2_LEV, 3 | (7 << 4));
 904        if (!ret)
 905                ret = reg_write(client, RJ54N1_SCALE_4_LEV, 0xf);
 906
 907        /* Switch to fixed resize mode */
 908        if (!ret)
 909                ret = reg_write(client, RJ54N1_RESIZE_CONTROL,
 910                                RESIZE_HOLD_SEL | 1);
 911
 912        /* Set gain */
 913        if (!ret)
 914                ret = reg_write(client, RJ54N1_Y_GAIN, 0x84);
 915
 916        /*
 917         * Mirror the image back: default is upside down and left-to-right...
 918         * Set manual preview / still shot switching
 919         */
 920        if (!ret)
 921                ret = reg_write(client, RJ54N1_MIRROR_STILL_MODE, 0x27);
 922
 923        if (!ret)
 924                ret = reg_write_multiple(client, bank_4, ARRAY_SIZE(bank_4));
 925
 926        /* Auto exposure area */
 927        if (!ret)
 928                ret = reg_write(client, RJ54N1_EXPOSURE_CONTROL, 0x80);
 929        /* Check current auto WB config */
 930        if (!ret)
 931                ret = reg_read(client, RJ54N1_WB_SEL_WEIGHT_I);
 932        if (ret >= 0) {
 933                rj54n1->auto_wb = ret & 0x80;
 934                ret = reg_write_multiple(client, bank_5, ARRAY_SIZE(bank_5));
 935        }
 936        if (!ret)
 937                ret = reg_write_multiple(client, bank_8, ARRAY_SIZE(bank_8));
 938
 939        if (!ret)
 940                ret = reg_write(client, RJ54N1_RESET_STANDBY,
 941                                E_EXCLK | DSP_RSTX | SEN_RSTX);
 942
 943        /* Commit init */
 944        if (!ret)
 945                ret = rj54n1_commit(client);
 946
 947        /* Take DSP, TG, sensor out of reset */
 948        if (!ret)
 949                ret = reg_write(client, RJ54N1_RESET_STANDBY,
 950                                E_EXCLK | DSP_RSTX | TG_RSTX | SEN_RSTX);
 951
 952        /* Start register update? Same register as 0x?FE in many bank_* sets */
 953        if (!ret)
 954                ret = reg_write(client, RJ54N1_FWFLG, 2);
 955
 956        /* Constant taken from manufacturer's example */
 957        msleep(700);
 958
 959        return ret;
 960}
 961
 962static int rj54n1_try_fmt(struct v4l2_subdev *sd,
 963                          struct v4l2_mbus_framefmt *mf)
 964{
 965        struct i2c_client *client = v4l2_get_subdevdata(sd);
 966        struct rj54n1 *rj54n1 = to_rj54n1(client);
 967        const struct rj54n1_datafmt *fmt;
 968        int align = mf->code == V4L2_MBUS_FMT_SBGGR10_1X10 ||
 969                mf->code == V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_BE ||
 970                mf->code == V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_BE ||
 971                mf->code == V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_LE ||
 972                mf->code == V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_LE;
 973
 974        dev_dbg(&client->dev, "%s: code = %d, width = %u, height = %u\n",
 975                __func__, mf->code, mf->width, mf->height);
 976
 977        fmt = rj54n1_find_datafmt(mf->code, rj54n1_colour_fmts,
 978                                  ARRAY_SIZE(rj54n1_colour_fmts));
 979        if (!fmt) {
 980                fmt = rj54n1->fmt;
 981                mf->code = fmt->code;
 982        }
 983
 984        mf->field       = V4L2_FIELD_NONE;
 985        mf->colorspace  = fmt->colorspace;
 986
 987        v4l_bound_align_image(&mf->width, 112, RJ54N1_MAX_WIDTH, align,
 988                              &mf->height, 84, RJ54N1_MAX_HEIGHT, align, 0);
 989
 990        return 0;
 991}
 992
 993static int rj54n1_s_fmt(struct v4l2_subdev *sd,
 994                        struct v4l2_mbus_framefmt *mf)
 995{
 996        struct i2c_client *client = v4l2_get_subdevdata(sd);
 997        struct rj54n1 *rj54n1 = to_rj54n1(client);
 998        const struct rj54n1_datafmt *fmt;
 999        int output_w, output_h, max_w, max_h,
1000                input_w = rj54n1->rect.width, input_h = rj54n1->rect.height;
1001        int ret;
1002
1003        /*
1004         * The host driver can call us without .try_fmt(), so, we have to take
1005         * care ourseleves
1006         */
1007        rj54n1_try_fmt(sd, mf);
1008
1009        /*
1010         * Verify if the sensor has just been powered on. TODO: replace this
1011         * with proper PM, when a suitable API is available.
1012         */
1013        ret = reg_read(client, RJ54N1_RESET_STANDBY);
1014        if (ret < 0)
1015                return ret;
1016
1017        if (!(ret & E_EXCLK)) {
1018                ret = rj54n1_reg_init(client);
1019                if (ret < 0)
1020                        return ret;
1021        }
1022
1023        dev_dbg(&client->dev, "%s: code = %d, width = %u, height = %u\n",
1024                __func__, mf->code, mf->width, mf->height);
1025
1026        /* RA_SEL_UL is only relevant for raw modes, ignored otherwise. */
1027        switch (mf->code) {
1028        case V4L2_MBUS_FMT_YUYV8_2X8:
1029                ret = reg_write(client, RJ54N1_OUT_SEL, 0);
1030                if (!ret)
1031                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 8, 8);
1032                break;
1033        case V4L2_MBUS_FMT_YVYU8_2X8:
1034                ret = reg_write(client, RJ54N1_OUT_SEL, 0);
1035                if (!ret)
1036                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 0, 8);
1037                break;
1038        case V4L2_MBUS_FMT_RGB565_2X8_LE:
1039                ret = reg_write(client, RJ54N1_OUT_SEL, 0x11);
1040                if (!ret)
1041                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 8, 8);
1042                break;
1043        case V4L2_MBUS_FMT_RGB565_2X8_BE:
1044                ret = reg_write(client, RJ54N1_OUT_SEL, 0x11);
1045                if (!ret)
1046                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 0, 8);
1047                break;
1048        case V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_LE:
1049                ret = reg_write(client, RJ54N1_OUT_SEL, 4);
1050                if (!ret)
1051                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 8, 8);
1052                if (!ret)
1053                        ret = reg_write(client, RJ54N1_RA_SEL_UL, 0);
1054                break;
1055        case V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_LE:
1056                ret = reg_write(client, RJ54N1_OUT_SEL, 4);
1057                if (!ret)
1058                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 8, 8);
1059                if (!ret)
1060                        ret = reg_write(client, RJ54N1_RA_SEL_UL, 8);
1061                break;
1062        case V4L2_MBUS_FMT_SBGGR10_2X8_PADLO_BE:
1063                ret = reg_write(client, RJ54N1_OUT_SEL, 4);
1064                if (!ret)
1065                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 0, 8);
1066                if (!ret)
1067                        ret = reg_write(client, RJ54N1_RA_SEL_UL, 0);
1068                break;
1069        case V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_BE:
1070                ret = reg_write(client, RJ54N1_OUT_SEL, 4);
1071                if (!ret)
1072                        ret = reg_set(client, RJ54N1_BYTE_SWAP, 0, 8);
1073                if (!ret)
1074                        ret = reg_write(client, RJ54N1_RA_SEL_UL, 8);
1075                break;
1076        case V4L2_MBUS_FMT_SBGGR10_1X10:
1077                ret = reg_write(client, RJ54N1_OUT_SEL, 5);
1078                break;
1079        default:
1080                ret = -EINVAL;
1081        }
1082
1083        /* Special case: a raw mode with 10 bits of data per clock tick */
1084        if (!ret)
1085                ret = reg_set(client, RJ54N1_OCLK_SEL_EN,
1086                              (mf->code == V4L2_MBUS_FMT_SBGGR10_1X10) << 1, 2);
1087
1088        if (ret < 0)
1089                return ret;
1090
1091        /* Supported scales 1:1 >= scale > 1:16 */
1092        max_w = mf->width * (16 * 1024 - 1) / 1024;
1093        if (input_w > max_w)
1094                input_w = max_w;
1095        max_h = mf->height * (16 * 1024 - 1) / 1024;
1096        if (input_h > max_h)
1097                input_h = max_h;
1098
1099        output_w = mf->width;
1100        output_h = mf->height;
1101
1102        ret = rj54n1_sensor_scale(sd, &input_w, &input_h, &output_w, &output_h);
1103        if (ret < 0)
1104                return ret;
1105
1106        fmt = rj54n1_find_datafmt(mf->code, rj54n1_colour_fmts,
1107                                  ARRAY_SIZE(rj54n1_colour_fmts));
1108
1109        rj54n1->fmt             = fmt;
1110        rj54n1->resize          = ret;
1111        rj54n1->rect.width      = input_w;
1112        rj54n1->rect.height     = input_h;
1113        rj54n1->width           = output_w;
1114        rj54n1->height          = output_h;
1115
1116        mf->width               = output_w;
1117        mf->height              = output_h;
1118        mf->field               = V4L2_FIELD_NONE;
1119        mf->colorspace          = fmt->colorspace;
1120
1121        return 0;
1122}
1123
1124#ifdef CONFIG_VIDEO_ADV_DEBUG
1125static int rj54n1_g_register(struct v4l2_subdev *sd,
1126                             struct v4l2_dbg_register *reg)
1127{
1128        struct i2c_client *client = v4l2_get_subdevdata(sd);
1129
1130        if (reg->reg < 0x400 || reg->reg > 0x1fff)
1131                /* Registers > 0x0800 are only available from Sharp support */
1132                return -EINVAL;
1133
1134        reg->size = 1;
1135        reg->val = reg_read(client, reg->reg);
1136
1137        if (reg->val > 0xff)
1138                return -EIO;
1139
1140        return 0;
1141}
1142
1143static int rj54n1_s_register(struct v4l2_subdev *sd,
1144                             const struct v4l2_dbg_register *reg)
1145{
1146        struct i2c_client *client = v4l2_get_subdevdata(sd);
1147
1148        if (reg->reg < 0x400 || reg->reg > 0x1fff)
1149                /* Registers >= 0x0800 are only available from Sharp support */
1150                return -EINVAL;
1151
1152        if (reg_write(client, reg->reg, reg->val) < 0)
1153                return -EIO;
1154
1155        return 0;
1156}
1157#endif
1158
1159static int rj54n1_s_power(struct v4l2_subdev *sd, int on)
1160{
1161        struct i2c_client *client = v4l2_get_subdevdata(sd);
1162        struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
1163        struct rj54n1 *rj54n1 = to_rj54n1(client);
1164
1165        return soc_camera_set_power(&client->dev, ssdd, rj54n1->clk, on);
1166}
1167
1168static int rj54n1_s_ctrl(struct v4l2_ctrl *ctrl)
1169{
1170        struct rj54n1 *rj54n1 = container_of(ctrl->handler, struct rj54n1, hdl);
1171        struct v4l2_subdev *sd = &rj54n1->subdev;
1172        struct i2c_client *client = v4l2_get_subdevdata(sd);
1173        int data;
1174
1175        switch (ctrl->id) {
1176        case V4L2_CID_VFLIP:
1177                if (ctrl->val)
1178                        data = reg_set(client, RJ54N1_MIRROR_STILL_MODE, 0, 1);
1179                else
1180                        data = reg_set(client, RJ54N1_MIRROR_STILL_MODE, 1, 1);
1181                if (data < 0)
1182                        return -EIO;
1183                return 0;
1184        case V4L2_CID_HFLIP:
1185                if (ctrl->val)
1186                        data = reg_set(client, RJ54N1_MIRROR_STILL_MODE, 0, 2);
1187                else
1188                        data = reg_set(client, RJ54N1_MIRROR_STILL_MODE, 2, 2);
1189                if (data < 0)
1190                        return -EIO;
1191                return 0;
1192        case V4L2_CID_GAIN:
1193                if (reg_write(client, RJ54N1_Y_GAIN, ctrl->val * 2) < 0)
1194                        return -EIO;
1195                return 0;
1196        case V4L2_CID_AUTO_WHITE_BALANCE:
1197                /* Auto WB area - whole image */
1198                if (reg_set(client, RJ54N1_WB_SEL_WEIGHT_I, ctrl->val << 7,
1199                            0x80) < 0)
1200                        return -EIO;
1201                rj54n1->auto_wb = ctrl->val;
1202                return 0;
1203        }
1204
1205        return -EINVAL;
1206}
1207
1208static const struct v4l2_ctrl_ops rj54n1_ctrl_ops = {
1209        .s_ctrl = rj54n1_s_ctrl,
1210};
1211
1212static struct v4l2_subdev_core_ops rj54n1_subdev_core_ops = {
1213#ifdef CONFIG_VIDEO_ADV_DEBUG
1214        .g_register     = rj54n1_g_register,
1215        .s_register     = rj54n1_s_register,
1216#endif
1217        .s_power        = rj54n1_s_power,
1218};
1219
1220static int rj54n1_g_mbus_config(struct v4l2_subdev *sd,
1221                                struct v4l2_mbus_config *cfg)
1222{
1223        struct i2c_client *client = v4l2_get_subdevdata(sd);
1224        struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
1225
1226        cfg->flags =
1227                V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING |
1228                V4L2_MBUS_MASTER | V4L2_MBUS_DATA_ACTIVE_HIGH |
1229                V4L2_MBUS_HSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_HIGH;
1230        cfg->type = V4L2_MBUS_PARALLEL;
1231        cfg->flags = soc_camera_apply_board_flags(ssdd, cfg);
1232
1233        return 0;
1234}
1235
1236static int rj54n1_s_mbus_config(struct v4l2_subdev *sd,
1237                                const struct v4l2_mbus_config *cfg)
1238{
1239        struct i2c_client *client = v4l2_get_subdevdata(sd);
1240        struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
1241
1242        /* Figures 2.5-1 to 2.5-3 - default falling pixclk edge */
1243        if (soc_camera_apply_board_flags(ssdd, cfg) &
1244            V4L2_MBUS_PCLK_SAMPLE_RISING)
1245                return reg_write(client, RJ54N1_OUT_SIGPO, 1 << 4);
1246        else
1247                return reg_write(client, RJ54N1_OUT_SIGPO, 0);
1248}
1249
1250static struct v4l2_subdev_video_ops rj54n1_subdev_video_ops = {
1251        .s_stream       = rj54n1_s_stream,
1252        .s_mbus_fmt     = rj54n1_s_fmt,
1253        .g_mbus_fmt     = rj54n1_g_fmt,
1254        .try_mbus_fmt   = rj54n1_try_fmt,
1255        .enum_mbus_fmt  = rj54n1_enum_fmt,
1256        .g_crop         = rj54n1_g_crop,
1257        .s_crop         = rj54n1_s_crop,
1258        .cropcap        = rj54n1_cropcap,
1259        .g_mbus_config  = rj54n1_g_mbus_config,
1260        .s_mbus_config  = rj54n1_s_mbus_config,
1261};
1262
1263static struct v4l2_subdev_ops rj54n1_subdev_ops = {
1264        .core   = &rj54n1_subdev_core_ops,
1265        .video  = &rj54n1_subdev_video_ops,
1266};
1267
1268/*
1269 * Interface active, can use i2c. If it fails, it can indeed mean, that
1270 * this wasn't our capture interface, so, we wait for the right one
1271 */
1272static int rj54n1_video_probe(struct i2c_client *client,
1273                              struct rj54n1_pdata *priv)
1274{
1275        struct rj54n1 *rj54n1 = to_rj54n1(client);
1276        int data1, data2;
1277        int ret;
1278
1279        ret = rj54n1_s_power(&rj54n1->subdev, 1);
1280        if (ret < 0)
1281                return ret;
1282
1283        /* Read out the chip version register */
1284        data1 = reg_read(client, RJ54N1_DEV_CODE);
1285        data2 = reg_read(client, RJ54N1_DEV_CODE2);
1286
1287        if (data1 != 0x51 || data2 != 0x10) {
1288                ret = -ENODEV;
1289                dev_info(&client->dev, "No RJ54N1CB0C found, read 0x%x:0x%x\n",
1290                         data1, data2);
1291                goto done;
1292        }
1293
1294        /* Configure IOCTL polarity from the platform data: 0 or 1 << 7. */
1295        ret = reg_write(client, RJ54N1_IOC, priv->ioctl_high << 7);
1296        if (ret < 0)
1297                goto done;
1298
1299        dev_info(&client->dev, "Detected a RJ54N1CB0C chip ID 0x%x:0x%x\n",
1300                 data1, data2);
1301
1302        ret = v4l2_ctrl_handler_setup(&rj54n1->hdl);
1303
1304done:
1305        rj54n1_s_power(&rj54n1->subdev, 0);
1306        return ret;
1307}
1308
1309static int rj54n1_probe(struct i2c_client *client,
1310                        const struct i2c_device_id *did)
1311{
1312        struct rj54n1 *rj54n1;
1313        struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
1314        struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
1315        struct rj54n1_pdata *rj54n1_priv;
1316        int ret;
1317
1318        if (!ssdd || !ssdd->drv_priv) {
1319                dev_err(&client->dev, "RJ54N1CB0C: missing platform data!\n");
1320                return -EINVAL;
1321        }
1322
1323        rj54n1_priv = ssdd->drv_priv;
1324
1325        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
1326                dev_warn(&adapter->dev,
1327                         "I2C-Adapter doesn't support I2C_FUNC_SMBUS_BYTE\n");
1328                return -EIO;
1329        }
1330
1331        rj54n1 = devm_kzalloc(&client->dev, sizeof(struct rj54n1), GFP_KERNEL);
1332        if (!rj54n1)
1333                return -ENOMEM;
1334
1335        v4l2_i2c_subdev_init(&rj54n1->subdev, client, &rj54n1_subdev_ops);
1336        v4l2_ctrl_handler_init(&rj54n1->hdl, 4);
1337        v4l2_ctrl_new_std(&rj54n1->hdl, &rj54n1_ctrl_ops,
1338                        V4L2_CID_VFLIP, 0, 1, 1, 0);
1339        v4l2_ctrl_new_std(&rj54n1->hdl, &rj54n1_ctrl_ops,
1340                        V4L2_CID_HFLIP, 0, 1, 1, 0);
1341        v4l2_ctrl_new_std(&rj54n1->hdl, &rj54n1_ctrl_ops,
1342                        V4L2_CID_GAIN, 0, 127, 1, 66);
1343        v4l2_ctrl_new_std(&rj54n1->hdl, &rj54n1_ctrl_ops,
1344                        V4L2_CID_AUTO_WHITE_BALANCE, 0, 1, 1, 1);
1345        rj54n1->subdev.ctrl_handler = &rj54n1->hdl;
1346        if (rj54n1->hdl.error)
1347                return rj54n1->hdl.error;
1348
1349        rj54n1->clk_div         = clk_div;
1350        rj54n1->rect.left       = RJ54N1_COLUMN_SKIP;
1351        rj54n1->rect.top        = RJ54N1_ROW_SKIP;
1352        rj54n1->rect.width      = RJ54N1_MAX_WIDTH;
1353        rj54n1->rect.height     = RJ54N1_MAX_HEIGHT;
1354        rj54n1->width           = RJ54N1_MAX_WIDTH;
1355        rj54n1->height          = RJ54N1_MAX_HEIGHT;
1356        rj54n1->fmt             = &rj54n1_colour_fmts[0];
1357        rj54n1->resize          = 1024;
1358        rj54n1->tgclk_mhz       = (rj54n1_priv->mclk_freq / PLL_L * PLL_N) /
1359                (clk_div.ratio_tg + 1) / (clk_div.ratio_t + 1);
1360
1361        rj54n1->clk = v4l2_clk_get(&client->dev, "mclk");
1362        if (IS_ERR(rj54n1->clk)) {
1363                ret = PTR_ERR(rj54n1->clk);
1364                goto eclkget;
1365        }
1366
1367        ret = rj54n1_video_probe(client, rj54n1_priv);
1368        if (ret < 0) {
1369                v4l2_clk_put(rj54n1->clk);
1370eclkget:
1371                v4l2_ctrl_handler_free(&rj54n1->hdl);
1372        }
1373
1374        return ret;
1375}
1376
1377static int rj54n1_remove(struct i2c_client *client)
1378{
1379        struct rj54n1 *rj54n1 = to_rj54n1(client);
1380        struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
1381
1382        v4l2_clk_put(rj54n1->clk);
1383        v4l2_device_unregister_subdev(&rj54n1->subdev);
1384        if (ssdd->free_bus)
1385                ssdd->free_bus(ssdd);
1386        v4l2_ctrl_handler_free(&rj54n1->hdl);
1387
1388        return 0;
1389}
1390
1391static const struct i2c_device_id rj54n1_id[] = {
1392        { "rj54n1cb0c", 0 },
1393        { }
1394};
1395MODULE_DEVICE_TABLE(i2c, rj54n1_id);
1396
1397static struct i2c_driver rj54n1_i2c_driver = {
1398        .driver = {
1399                .name = "rj54n1cb0c",
1400        },
1401        .probe          = rj54n1_probe,
1402        .remove         = rj54n1_remove,
1403        .id_table       = rj54n1_id,
1404};
1405
1406module_i2c_driver(rj54n1_i2c_driver);
1407
1408MODULE_DESCRIPTION("Sharp RJ54N1CB0C Camera driver");
1409MODULE_AUTHOR("Guennadi Liakhovetski <g.liakhovetski@gmx.de>");
1410MODULE_LICENSE("GPL v2");
1411