LXR linux/include/linux/usb/musb.h

   1/*
   2 * This is used to for host and peripheral modes of the driver for
   3 * Inventra (Multidrop) Highspeed Dual-Role Controllers:  (M)HDRC.
   4 *
   5 * Board initialization should put one of these into dev->platform_data,
   6 * probably on some platform_device named "musb-hdrc".  It encapsulates
   7 * key configuration differences between boards.
   8 */
   9
  10#ifndef __LINUX_USB_MUSB_H
  11#define __LINUX_USB_MUSB_H
  12
  13/* The USB role is defined by the connector used on the board, so long as
  14 * standards are being followed.  (Developer boards sometimes won't.)
  15 */
  16enum musb_mode {
  17        MUSB_UNDEFINED = 0,
  18        MUSB_HOST,              /* A or Mini-A connector */
  19        MUSB_PERIPHERAL,        /* B or Mini-B connector */
  20        MUSB_OTG                /* Mini-AB connector */
  21};
  22
  23struct clk;
  24
  25enum musb_fifo_style {
  26        FIFO_RXTX,
  27        FIFO_TX,
  28        FIFO_RX
  29} __attribute__ ((packed));
  30
  31enum musb_buf_mode {
  32        BUF_SINGLE,
  33        BUF_DOUBLE
  34} __attribute__ ((packed));
  35
  36struct musb_fifo_cfg {
  37        u8                      hw_ep_num;
  38        enum musb_fifo_style    style;
  39        enum musb_buf_mode      mode;
  40        u16                     maxpacket;
  41};
  42
  43#define MUSB_EP_FIFO(ep, st, m, pkt)            \
  44{                                               \
  45        .hw_ep_num      = ep,                   \
  46        .style          = st,                   \
  47        .mode           = m,                    \
  48        .maxpacket      = pkt,                  \
  49}
  50
  51#define MUSB_EP_FIFO_SINGLE(ep, st, pkt)        \
  52        MUSB_EP_FIFO(ep, st, BUF_SINGLE, pkt)
  53
  54#define MUSB_EP_FIFO_DOUBLE(ep, st, pkt)        \
  55        MUSB_EP_FIFO(ep, st, BUF_DOUBLE, pkt)
  56
  57struct musb_hdrc_eps_bits {
  58        const char      name[16];
  59        u8              bits;
  60};
  61
  62struct musb_hdrc_config {
  63        struct musb_fifo_cfg    *fifo_cfg;      /* board fifo configuration */
  64        unsigned                fifo_cfg_size;  /* size of the fifo configuration */
  65
  66        /* MUSB configuration-specific details */
  67        unsigned        multipoint:1;   /* multipoint device */
  68        unsigned        dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */
  69        unsigned        soft_con:1 __deprecated; /* soft connect required */
  70        unsigned        utm_16:1 __deprecated; /* utm data witdh is 16 bits */
  71        unsigned        big_endian:1;   /* true if CPU uses big-endian */
  72        unsigned        mult_bulk_tx:1; /* Tx ep required for multbulk pkts */
  73        unsigned        mult_bulk_rx:1; /* Rx ep required for multbulk pkts */
  74        unsigned        high_iso_tx:1;  /* Tx ep required for HB iso */
  75        unsigned        high_iso_rx:1;  /* Rx ep required for HD iso */
  76        unsigned        dma:1 __deprecated; /* supports DMA */
  77        unsigned        vendor_req:1 __deprecated; /* vendor registers required */
  78
  79        u8              num_eps;        /* number of endpoints _with_ ep0 */
  80        u8              dma_channels __deprecated; /* number of dma channels */
  81        u8              dyn_fifo_size;  /* dynamic size in bytes */
  82        u8              vendor_ctrl __deprecated; /* vendor control reg width */
  83        u8              vendor_stat __deprecated; /* vendor status reg witdh */
  84        u8              dma_req_chan __deprecated; /* bitmask for required dma channels */
  85        u8              ram_bits;       /* ram address size */
  86
  87        struct musb_hdrc_eps_bits *eps_bits __deprecated;
  88#ifdef CONFIG_BLACKFIN
  89        /* A GPIO controlling VRSEL in Blackfin */
  90        unsigned int    gpio_vrsel;
  91        unsigned int    gpio_vrsel_active;
  92        /* musb CLKIN in Blackfin in MHZ */
  93        unsigned char   clkin;
  94#endif
  95
  96};
  97
  98struct musb_hdrc_platform_data {
  99        /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
 100        u8              mode;
 101
 102        u8              has_mailbox:1;
 103
 104        /* for clk_get() */
 105        const char      *clock;
 106
 107        /* (HOST or OTG) switch VBUS on/off */
 108        int             (*set_vbus)(struct device *dev, int is_on);
 109
 110        /* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
 111        u8              power;
 112
 113        /* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
 114        u8              min_power;
 115
 116        /* (HOST or OTG) msec/2 after VBUS on till power good */
 117        u8              potpgt;
 118
 119        /* (HOST or OTG) program PHY for external Vbus */
 120        unsigned        extvbus:1;
 121
 122        /* Power the device on or off */
 123        int             (*set_power)(int state);
 124
 125        /* MUSB configuration-specific details */
 126        struct musb_hdrc_config *config;
 127
 128        /* Architecture specific board data     */
 129        void            *board_data;
 130
 131        /* Platform specific struct musb_ops pointer */
 132        const void      *platform_ops;
 133};
 134
 135
 136/* TUSB 6010 support */
 137
 138#define TUSB6010_OSCCLK_60      16667   /* psec/clk @ 60.0 MHz */
 139#define TUSB6010_REFCLK_24      41667   /* psec/clk @ 24.0 MHz XI */
 140#define TUSB6010_REFCLK_19      52083   /* psec/clk @ 19.2 MHz CLKIN */
 141
 142#ifdef  CONFIG_ARCH_OMAP2
 143
 144extern int __init tusb6010_setup_interface(
 145                struct musb_hdrc_platform_data *data,
 146                unsigned ps_refclk, unsigned waitpin,
 147                unsigned async_cs, unsigned sync_cs,
 148                unsigned irq, unsigned dmachan);
 149
 150extern int tusb6010_platform_retime(unsigned is_refclk);
 151
 152#endif  /* OMAP2 */
 153
 154#endif /* __LINUX_USB_MUSB_H */
 155