linux/drivers/hwmon/w83795.c
<<
>>
Prefs
   1/*
   2 *  w83795.c - Linux kernel driver for hardware monitoring
   3 *  Copyright (C) 2008 Nuvoton Technology Corp.
   4 *                Wei Song
   5 *  Copyright (C) 2010 Jean Delvare <jdelvare@suse.de>
   6 *
   7 *  This program is free software; you can redistribute it and/or modify
   8 *  it under the terms of the GNU General Public License as published by
   9 *  the Free Software Foundation - version 2.
  10 *
  11 *  This program is distributed in the hope that it will be useful,
  12 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
  13 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  14 *  GNU General Public License for more details.
  15 *
  16 *  You should have received a copy of the GNU General Public License
  17 *  along with this program; if not, write to the Free Software
  18 *  Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
  19 *  02110-1301 USA.
  20 *
  21 *  Supports following chips:
  22 *
  23 *  Chip       #vin   #fanin #pwm #temp #dts wchipid  vendid  i2c  ISA
  24 *  w83795g     21     14     8     6     8    0x79   0x5ca3  yes   no
  25 *  w83795adg   18     14     2     6     8    0x79   0x5ca3  yes   no
  26 */
  27
  28#include <linux/kernel.h>
  29#include <linux/module.h>
  30#include <linux/init.h>
  31#include <linux/slab.h>
  32#include <linux/i2c.h>
  33#include <linux/hwmon.h>
  34#include <linux/hwmon-sysfs.h>
  35#include <linux/err.h>
  36#include <linux/mutex.h>
  37#include <linux/jiffies.h>
  38
  39/* Addresses to scan */
  40static const unsigned short normal_i2c[] = {
  41        0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END
  42};
  43
  44
  45static bool reset;
  46module_param(reset, bool, 0);
  47MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended");
  48
  49
  50#define W83795_REG_BANKSEL              0x00
  51#define W83795_REG_VENDORID             0xfd
  52#define W83795_REG_CHIPID               0xfe
  53#define W83795_REG_DEVICEID             0xfb
  54#define W83795_REG_DEVICEID_A           0xff
  55
  56#define W83795_REG_I2C_ADDR             0xfc
  57#define W83795_REG_CONFIG               0x01
  58#define W83795_REG_CONFIG_CONFIG48      0x04
  59#define W83795_REG_CONFIG_START 0x01
  60
  61/* Multi-Function Pin Ctrl Registers */
  62#define W83795_REG_VOLT_CTRL1           0x02
  63#define W83795_REG_VOLT_CTRL2           0x03
  64#define W83795_REG_TEMP_CTRL1           0x04
  65#define W83795_REG_TEMP_CTRL2           0x05
  66#define W83795_REG_FANIN_CTRL1          0x06
  67#define W83795_REG_FANIN_CTRL2          0x07
  68#define W83795_REG_VMIGB_CTRL           0x08
  69
  70#define TEMP_READ                       0
  71#define TEMP_CRIT                       1
  72#define TEMP_CRIT_HYST                  2
  73#define TEMP_WARN                       3
  74#define TEMP_WARN_HYST                  4
  75/*
  76 * only crit and crit_hyst affect real-time alarm status
  77 * current crit crit_hyst warn warn_hyst
  78 */
  79static const u16 W83795_REG_TEMP[][5] = {
  80        {0x21, 0x96, 0x97, 0x98, 0x99}, /* TD1/TR1 */
  81        {0x22, 0x9a, 0x9b, 0x9c, 0x9d}, /* TD2/TR2 */
  82        {0x23, 0x9e, 0x9f, 0xa0, 0xa1}, /* TD3/TR3 */
  83        {0x24, 0xa2, 0xa3, 0xa4, 0xa5}, /* TD4/TR4 */
  84        {0x1f, 0xa6, 0xa7, 0xa8, 0xa9}, /* TR5 */
  85        {0x20, 0xaa, 0xab, 0xac, 0xad}, /* TR6 */
  86};
  87
  88#define IN_READ                         0
  89#define IN_MAX                          1
  90#define IN_LOW                          2
  91static const u16 W83795_REG_IN[][3] = {
  92        /* Current, HL, LL */
  93        {0x10, 0x70, 0x71},     /* VSEN1 */
  94        {0x11, 0x72, 0x73},     /* VSEN2 */
  95        {0x12, 0x74, 0x75},     /* VSEN3 */
  96        {0x13, 0x76, 0x77},     /* VSEN4 */
  97        {0x14, 0x78, 0x79},     /* VSEN5 */
  98        {0x15, 0x7a, 0x7b},     /* VSEN6 */
  99        {0x16, 0x7c, 0x7d},     /* VSEN7 */
 100        {0x17, 0x7e, 0x7f},     /* VSEN8 */
 101        {0x18, 0x80, 0x81},     /* VSEN9 */
 102        {0x19, 0x82, 0x83},     /* VSEN10 */
 103        {0x1A, 0x84, 0x85},     /* VSEN11 */
 104        {0x1B, 0x86, 0x87},     /* VTT */
 105        {0x1C, 0x88, 0x89},     /* 3VDD */
 106        {0x1D, 0x8a, 0x8b},     /* 3VSB */
 107        {0x1E, 0x8c, 0x8d},     /* VBAT */
 108        {0x1F, 0xa6, 0xa7},     /* VSEN12 */
 109        {0x20, 0xaa, 0xab},     /* VSEN13 */
 110        {0x21, 0x96, 0x97},     /* VSEN14 */
 111        {0x22, 0x9a, 0x9b},     /* VSEN15 */
 112        {0x23, 0x9e, 0x9f},     /* VSEN16 */
 113        {0x24, 0xa2, 0xa3},     /* VSEN17 */
 114};
 115#define W83795_REG_VRLSB                0x3C
 116
 117static const u8 W83795_REG_IN_HL_LSB[] = {
 118        0x8e,   /* VSEN1-4 */
 119        0x90,   /* VSEN5-8 */
 120        0x92,   /* VSEN9-11 */
 121        0x94,   /* VTT, 3VDD, 3VSB, 3VBAT */
 122        0xa8,   /* VSEN12 */
 123        0xac,   /* VSEN13 */
 124        0x98,   /* VSEN14 */
 125        0x9c,   /* VSEN15 */
 126        0xa0,   /* VSEN16 */
 127        0xa4,   /* VSEN17 */
 128};
 129
 130#define IN_LSB_REG(index, type) \
 131        (((type) == 1) ? W83795_REG_IN_HL_LSB[(index)] \
 132        : (W83795_REG_IN_HL_LSB[(index)] + 1))
 133
 134#define IN_LSB_SHIFT                    0
 135#define IN_LSB_IDX                      1
 136static const u8 IN_LSB_SHIFT_IDX[][2] = {
 137        /* High/Low LSB shift, LSB No. */
 138        {0x00, 0x00},   /* VSEN1 */
 139        {0x02, 0x00},   /* VSEN2 */
 140        {0x04, 0x00},   /* VSEN3 */
 141        {0x06, 0x00},   /* VSEN4 */
 142        {0x00, 0x01},   /* VSEN5 */
 143        {0x02, 0x01},   /* VSEN6 */
 144        {0x04, 0x01},   /* VSEN7 */
 145        {0x06, 0x01},   /* VSEN8 */
 146        {0x00, 0x02},   /* VSEN9 */
 147        {0x02, 0x02},   /* VSEN10 */
 148        {0x04, 0x02},   /* VSEN11 */
 149        {0x00, 0x03},   /* VTT */
 150        {0x02, 0x03},   /* 3VDD */
 151        {0x04, 0x03},   /* 3VSB */
 152        {0x06, 0x03},   /* VBAT */
 153        {0x06, 0x04},   /* VSEN12 */
 154        {0x06, 0x05},   /* VSEN13 */
 155        {0x06, 0x06},   /* VSEN14 */
 156        {0x06, 0x07},   /* VSEN15 */
 157        {0x06, 0x08},   /* VSEN16 */
 158        {0x06, 0x09},   /* VSEN17 */
 159};
 160
 161
 162#define W83795_REG_FAN(index)           (0x2E + (index))
 163#define W83795_REG_FAN_MIN_HL(index)    (0xB6 + (index))
 164#define W83795_REG_FAN_MIN_LSB(index)   (0xC4 + (index) / 2)
 165#define W83795_REG_FAN_MIN_LSB_SHIFT(index) \
 166        (((index) & 1) ? 4 : 0)
 167
 168#define W83795_REG_VID_CTRL             0x6A
 169
 170#define W83795_REG_ALARM_CTRL           0x40
 171#define ALARM_CTRL_RTSACS               (1 << 7)
 172#define W83795_REG_ALARM(index)         (0x41 + (index))
 173#define W83795_REG_CLR_CHASSIS          0x4D
 174#define W83795_REG_BEEP(index)          (0x50 + (index))
 175
 176#define W83795_REG_OVT_CFG              0x58
 177#define OVT_CFG_SEL                     (1 << 7)
 178
 179
 180#define W83795_REG_FCMS1                0x201
 181#define W83795_REG_FCMS2                0x208
 182#define W83795_REG_TFMR(index)          (0x202 + (index))
 183#define W83795_REG_FOMC                 0x20F
 184
 185#define W83795_REG_TSS(index)           (0x209 + (index))
 186
 187#define TSS_MAP_RESERVED                0xff
 188static const u8 tss_map[4][6] = {
 189        { 0,  1,  2,  3,  4,  5},
 190        { 6,  7,  8,  9,  0,  1},
 191        {10, 11, 12, 13,  2,  3},
 192        { 4,  5,  4,  5, TSS_MAP_RESERVED, TSS_MAP_RESERVED},
 193};
 194
 195#define PWM_OUTPUT                      0
 196#define PWM_FREQ                        1
 197#define PWM_START                       2
 198#define PWM_NONSTOP                     3
 199#define PWM_STOP_TIME                   4
 200#define W83795_REG_PWM(index, nr)       (0x210 + (nr) * 8 + (index))
 201
 202#define W83795_REG_FTSH(index)          (0x240 + (index) * 2)
 203#define W83795_REG_FTSL(index)          (0x241 + (index) * 2)
 204#define W83795_REG_TFTS                 0x250
 205
 206#define TEMP_PWM_TTTI                   0
 207#define TEMP_PWM_CTFS                   1
 208#define TEMP_PWM_HCT                    2
 209#define TEMP_PWM_HOT                    3
 210#define W83795_REG_TTTI(index)          (0x260 + (index))
 211#define W83795_REG_CTFS(index)          (0x268 + (index))
 212#define W83795_REG_HT(index)            (0x270 + (index))
 213
 214#define SF4_TEMP                        0
 215#define SF4_PWM                         1
 216#define W83795_REG_SF4_TEMP(temp_num, index) \
 217        (0x280 + 0x10 * (temp_num) + (index))
 218#define W83795_REG_SF4_PWM(temp_num, index) \
 219        (0x288 + 0x10 * (temp_num) + (index))
 220
 221#define W83795_REG_DTSC                 0x301
 222#define W83795_REG_DTSE                 0x302
 223#define W83795_REG_DTS(index)           (0x26 + (index))
 224#define W83795_REG_PECI_TBASE(index)    (0x320 + (index))
 225
 226#define DTS_CRIT                        0
 227#define DTS_CRIT_HYST                   1
 228#define DTS_WARN                        2
 229#define DTS_WARN_HYST                   3
 230#define W83795_REG_DTS_EXT(index)       (0xB2 + (index))
 231
 232#define SETUP_PWM_DEFAULT               0
 233#define SETUP_PWM_UPTIME                1
 234#define SETUP_PWM_DOWNTIME              2
 235#define W83795_REG_SETUP_PWM(index)    (0x20C + (index))
 236
 237static inline u16 in_from_reg(u8 index, u16 val)
 238{
 239        /* 3VDD, 3VSB and VBAT: 6 mV/bit; other inputs: 2 mV/bit */
 240        if (index >= 12 && index <= 14)
 241                return val * 6;
 242        else
 243                return val * 2;
 244}
 245
 246static inline u16 in_to_reg(u8 index, u16 val)
 247{
 248        if (index >= 12 && index <= 14)
 249                return val / 6;
 250        else
 251                return val / 2;
 252}
 253
 254static inline unsigned long fan_from_reg(u16 val)
 255{
 256        if ((val == 0xfff) || (val == 0))
 257                return 0;
 258        return 1350000UL / val;
 259}
 260
 261static inline u16 fan_to_reg(long rpm)
 262{
 263        if (rpm <= 0)
 264                return 0x0fff;
 265        return clamp_val((1350000 + (rpm >> 1)) / rpm, 1, 0xffe);
 266}
 267
 268static inline unsigned long time_from_reg(u8 reg)
 269{
 270        return reg * 100;
 271}
 272
 273static inline u8 time_to_reg(unsigned long val)
 274{
 275        return clamp_val((val + 50) / 100, 0, 0xff);
 276}
 277
 278static inline long temp_from_reg(s8 reg)
 279{
 280        return reg * 1000;
 281}
 282
 283static inline s8 temp_to_reg(long val, s8 min, s8 max)
 284{
 285        return clamp_val(val / 1000, min, max);
 286}
 287
 288static const u16 pwm_freq_cksel0[16] = {
 289        1024, 512, 341, 256, 205, 171, 146, 128,
 290        85, 64, 32, 16, 8, 4, 2, 1
 291};
 292
 293static unsigned int pwm_freq_from_reg(u8 reg, u16 clkin)
 294{
 295        unsigned long base_clock;
 296
 297        if (reg & 0x80) {
 298                base_clock = clkin * 1000 / ((clkin == 48000) ? 384 : 256);
 299                return base_clock / ((reg & 0x7f) + 1);
 300        } else
 301                return pwm_freq_cksel0[reg & 0x0f];
 302}
 303
 304static u8 pwm_freq_to_reg(unsigned long val, u16 clkin)
 305{
 306        unsigned long base_clock;
 307        u8 reg0, reg1;
 308        unsigned long best0, best1;
 309
 310        /* Best fit for cksel = 0 */
 311        for (reg0 = 0; reg0 < ARRAY_SIZE(pwm_freq_cksel0) - 1; reg0++) {
 312                if (val > (pwm_freq_cksel0[reg0] +
 313                           pwm_freq_cksel0[reg0 + 1]) / 2)
 314                        break;
 315        }
 316        if (val < 375)  /* cksel = 1 can't beat this */
 317                return reg0;
 318        best0 = pwm_freq_cksel0[reg0];
 319
 320        /* Best fit for cksel = 1 */
 321        base_clock = clkin * 1000 / ((clkin == 48000) ? 384 : 256);
 322        reg1 = clamp_val(DIV_ROUND_CLOSEST(base_clock, val), 1, 128);
 323        best1 = base_clock / reg1;
 324        reg1 = 0x80 | (reg1 - 1);
 325
 326        /* Choose the closest one */
 327        if (abs(val - best0) > abs(val - best1))
 328                return reg1;
 329        else
 330                return reg0;
 331}
 332
 333enum chip_types {w83795g, w83795adg};
 334
 335struct w83795_data {
 336        struct device *hwmon_dev;
 337        struct mutex update_lock;
 338        unsigned long last_updated;     /* In jiffies */
 339        enum chip_types chip_type;
 340
 341        u8 bank;
 342
 343        u32 has_in;             /* Enable monitor VIN or not */
 344        u8 has_dyn_in;          /* Only in2-0 can have this */
 345        u16 in[21][3];          /* Register value, read/high/low */
 346        u8 in_lsb[10][3];       /* LSB Register value, high/low */
 347        u8 has_gain;            /* has gain: in17-20 * 8 */
 348
 349        u16 has_fan;            /* Enable fan14-1 or not */
 350        u16 fan[14];            /* Register value combine */
 351        u16 fan_min[14];        /* Register value combine */
 352
 353        u8 has_temp;            /* Enable monitor temp6-1 or not */
 354        s8 temp[6][5];          /* current, crit, crit_hyst, warn, warn_hyst */
 355        u8 temp_read_vrlsb[6];
 356        u8 temp_mode;           /* Bit vector, 0 = TR, 1 = TD */
 357        u8 temp_src[3];         /* Register value */
 358
 359        u8 enable_dts;          /*
 360                                 * Enable PECI and SB-TSI,
 361                                 * bit 0: =1 enable, =0 disable,
 362                                 * bit 1: =1 AMD SB-TSI, =0 Intel PECI
 363                                 */
 364        u8 has_dts;             /* Enable monitor DTS temp */
 365        s8 dts[8];              /* Register value */
 366        u8 dts_read_vrlsb[8];   /* Register value */
 367        s8 dts_ext[4];          /* Register value */
 368
 369        u8 has_pwm;             /*
 370                                 * 795g supports 8 pwm, 795adg only supports 2,
 371                                 * no config register, only affected by chip
 372                                 * type
 373                                 */
 374        u8 pwm[8][5];           /*
 375                                 * Register value, output, freq, start,
 376                                 *  non stop, stop time
 377                                 */
 378        u16 clkin;              /* CLKIN frequency in kHz */
 379        u8 pwm_fcms[2];         /* Register value */
 380        u8 pwm_tfmr[6];         /* Register value */
 381        u8 pwm_fomc;            /* Register value */
 382
 383        u16 target_speed[8];    /*
 384                                 * Register value, target speed for speed
 385                                 * cruise
 386                                 */
 387        u8 tol_speed;           /* tolerance of target speed */
 388        u8 pwm_temp[6][4];      /* TTTI, CTFS, HCT, HOT */
 389        u8 sf4_reg[6][2][7];    /* 6 temp, temp/dcpwm, 7 registers */
 390
 391        u8 setup_pwm[3];        /* Register value */
 392
 393        u8 alarms[6];           /* Register value */
 394        u8 enable_beep;
 395        u8 beeps[6];            /* Register value */
 396
 397        char valid;
 398        char valid_limits;
 399        char valid_pwm_config;
 400};
 401
 402/*
 403 * Hardware access
 404 * We assume that nobdody can change the bank outside the driver.
 405 */
 406
 407/* Must be called with data->update_lock held, except during initialization */
 408static int w83795_set_bank(struct i2c_client *client, u8 bank)
 409{
 410        struct w83795_data *data = i2c_get_clientdata(client);
 411        int err;
 412
 413        /* If the same bank is already set, nothing to do */
 414        if ((data->bank & 0x07) == bank)
 415                return 0;
 416
 417        /* Change to new bank, preserve all other bits */
 418        bank |= data->bank & ~0x07;
 419        err = i2c_smbus_write_byte_data(client, W83795_REG_BANKSEL, bank);
 420        if (err < 0) {
 421                dev_err(&client->dev,
 422                        "Failed to set bank to %d, err %d\n",
 423                        (int)bank, err);
 424                return err;
 425        }
 426        data->bank = bank;
 427
 428        return 0;
 429}
 430
 431/* Must be called with data->update_lock held, except during initialization */
 432static u8 w83795_read(struct i2c_client *client, u16 reg)
 433{
 434        int err;
 435
 436        err = w83795_set_bank(client, reg >> 8);
 437        if (err < 0)
 438                return 0x00;    /* Arbitrary */
 439
 440        err = i2c_smbus_read_byte_data(client, reg & 0xff);
 441        if (err < 0) {
 442                dev_err(&client->dev,
 443                        "Failed to read from register 0x%03x, err %d\n",
 444                        (int)reg, err);
 445                return 0x00;    /* Arbitrary */
 446        }
 447        return err;
 448}
 449
 450/* Must be called with data->update_lock held, except during initialization */
 451static int w83795_write(struct i2c_client *client, u16 reg, u8 value)
 452{
 453        int err;
 454
 455        err = w83795_set_bank(client, reg >> 8);
 456        if (err < 0)
 457                return err;
 458
 459        err = i2c_smbus_write_byte_data(client, reg & 0xff, value);
 460        if (err < 0)
 461                dev_err(&client->dev,
 462                        "Failed to write to register 0x%03x, err %d\n",
 463                        (int)reg, err);
 464        return err;
 465}
 466
 467static void w83795_update_limits(struct i2c_client *client)
 468{
 469        struct w83795_data *data = i2c_get_clientdata(client);
 470        int i, limit;
 471        u8 lsb;
 472
 473        /* Read the voltage limits */
 474        for (i = 0; i < ARRAY_SIZE(data->in); i++) {
 475                if (!(data->has_in & (1 << i)))
 476                        continue;
 477                data->in[i][IN_MAX] =
 478                        w83795_read(client, W83795_REG_IN[i][IN_MAX]);
 479                data->in[i][IN_LOW] =
 480                        w83795_read(client, W83795_REG_IN[i][IN_LOW]);
 481        }
 482        for (i = 0; i < ARRAY_SIZE(data->in_lsb); i++) {
 483                if ((i == 2 && data->chip_type == w83795adg) ||
 484                    (i >= 4 && !(data->has_in & (1 << (i + 11)))))
 485                        continue;
 486                data->in_lsb[i][IN_MAX] =
 487                        w83795_read(client, IN_LSB_REG(i, IN_MAX));
 488                data->in_lsb[i][IN_LOW] =
 489                        w83795_read(client, IN_LSB_REG(i, IN_LOW));
 490        }
 491
 492        /* Read the fan limits */
 493        lsb = 0; /* Silent false gcc warning */
 494        for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
 495                /*
 496                 * Each register contains LSB for 2 fans, but we want to
 497                 * read it only once to save time
 498                 */
 499                if ((i & 1) == 0 && (data->has_fan & (3 << i)))
 500                        lsb = w83795_read(client, W83795_REG_FAN_MIN_LSB(i));
 501
 502                if (!(data->has_fan & (1 << i)))
 503                        continue;
 504                data->fan_min[i] =
 505                        w83795_read(client, W83795_REG_FAN_MIN_HL(i)) << 4;
 506                data->fan_min[i] |=
 507                        (lsb >> W83795_REG_FAN_MIN_LSB_SHIFT(i)) & 0x0F;
 508        }
 509
 510        /* Read the temperature limits */
 511        for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
 512                if (!(data->has_temp & (1 << i)))
 513                        continue;
 514                for (limit = TEMP_CRIT; limit <= TEMP_WARN_HYST; limit++)
 515                        data->temp[i][limit] =
 516                                w83795_read(client, W83795_REG_TEMP[i][limit]);
 517        }
 518
 519        /* Read the DTS limits */
 520        if (data->enable_dts) {
 521                for (limit = DTS_CRIT; limit <= DTS_WARN_HYST; limit++)
 522                        data->dts_ext[limit] =
 523                                w83795_read(client, W83795_REG_DTS_EXT(limit));
 524        }
 525
 526        /* Read beep settings */
 527        if (data->enable_beep) {
 528                for (i = 0; i < ARRAY_SIZE(data->beeps); i++)
 529                        data->beeps[i] =
 530                                w83795_read(client, W83795_REG_BEEP(i));
 531        }
 532
 533        data->valid_limits = 1;
 534}
 535
 536static struct w83795_data *w83795_update_pwm_config(struct device *dev)
 537{
 538        struct i2c_client *client = to_i2c_client(dev);
 539        struct w83795_data *data = i2c_get_clientdata(client);
 540        int i, tmp;
 541
 542        mutex_lock(&data->update_lock);
 543
 544        if (data->valid_pwm_config)
 545                goto END;
 546
 547        /* Read temperature source selection */
 548        for (i = 0; i < ARRAY_SIZE(data->temp_src); i++)
 549                data->temp_src[i] = w83795_read(client, W83795_REG_TSS(i));
 550
 551        /* Read automatic fan speed control settings */
 552        data->pwm_fcms[0] = w83795_read(client, W83795_REG_FCMS1);
 553        data->pwm_fcms[1] = w83795_read(client, W83795_REG_FCMS2);
 554        for (i = 0; i < ARRAY_SIZE(data->pwm_tfmr); i++)
 555                data->pwm_tfmr[i] = w83795_read(client, W83795_REG_TFMR(i));
 556        data->pwm_fomc = w83795_read(client, W83795_REG_FOMC);
 557        for (i = 0; i < data->has_pwm; i++) {
 558                for (tmp = PWM_FREQ; tmp <= PWM_STOP_TIME; tmp++)
 559                        data->pwm[i][tmp] =
 560                                w83795_read(client, W83795_REG_PWM(i, tmp));
 561        }
 562        for (i = 0; i < ARRAY_SIZE(data->target_speed); i++) {
 563                data->target_speed[i] =
 564                        w83795_read(client, W83795_REG_FTSH(i)) << 4;
 565                data->target_speed[i] |=
 566                        w83795_read(client, W83795_REG_FTSL(i)) >> 4;
 567        }
 568        data->tol_speed = w83795_read(client, W83795_REG_TFTS) & 0x3f;
 569
 570        for (i = 0; i < ARRAY_SIZE(data->pwm_temp); i++) {
 571                data->pwm_temp[i][TEMP_PWM_TTTI] =
 572                        w83795_read(client, W83795_REG_TTTI(i)) & 0x7f;
 573                data->pwm_temp[i][TEMP_PWM_CTFS] =
 574                        w83795_read(client, W83795_REG_CTFS(i));
 575                tmp = w83795_read(client, W83795_REG_HT(i));
 576                data->pwm_temp[i][TEMP_PWM_HCT] = tmp >> 4;
 577                data->pwm_temp[i][TEMP_PWM_HOT] = tmp & 0x0f;
 578        }
 579
 580        /* Read SmartFanIV trip points */
 581        for (i = 0; i < ARRAY_SIZE(data->sf4_reg); i++) {
 582                for (tmp = 0; tmp < 7; tmp++) {
 583                        data->sf4_reg[i][SF4_TEMP][tmp] =
 584                                w83795_read(client,
 585                                            W83795_REG_SF4_TEMP(i, tmp));
 586                        data->sf4_reg[i][SF4_PWM][tmp] =
 587                                w83795_read(client, W83795_REG_SF4_PWM(i, tmp));
 588                }
 589        }
 590
 591        /* Read setup PWM */
 592        for (i = 0; i < ARRAY_SIZE(data->setup_pwm); i++)
 593                data->setup_pwm[i] =
 594                        w83795_read(client, W83795_REG_SETUP_PWM(i));
 595
 596        data->valid_pwm_config = 1;
 597
 598END:
 599        mutex_unlock(&data->update_lock);
 600        return data;
 601}
 602
 603static struct w83795_data *w83795_update_device(struct device *dev)
 604{
 605        struct i2c_client *client = to_i2c_client(dev);
 606        struct w83795_data *data = i2c_get_clientdata(client);
 607        u16 tmp;
 608        u8 intrusion;
 609        int i;
 610
 611        mutex_lock(&data->update_lock);
 612
 613        if (!data->valid_limits)
 614                w83795_update_limits(client);
 615
 616        if (!(time_after(jiffies, data->last_updated + HZ * 2)
 617              || !data->valid))
 618                goto END;
 619
 620        /* Update the voltages value */
 621        for (i = 0; i < ARRAY_SIZE(data->in); i++) {
 622                if (!(data->has_in & (1 << i)))
 623                        continue;
 624                tmp = w83795_read(client, W83795_REG_IN[i][IN_READ]) << 2;
 625                tmp |= w83795_read(client, W83795_REG_VRLSB) >> 6;
 626                data->in[i][IN_READ] = tmp;
 627        }
 628
 629        /* in0-2 can have dynamic limits (W83795G only) */
 630        if (data->has_dyn_in) {
 631                u8 lsb_max = w83795_read(client, IN_LSB_REG(0, IN_MAX));
 632                u8 lsb_low = w83795_read(client, IN_LSB_REG(0, IN_LOW));
 633
 634                for (i = 0; i < 3; i++) {
 635                        if (!(data->has_dyn_in & (1 << i)))
 636                                continue;
 637                        data->in[i][IN_MAX] =
 638                                w83795_read(client, W83795_REG_IN[i][IN_MAX]);
 639                        data->in[i][IN_LOW] =
 640                                w83795_read(client, W83795_REG_IN[i][IN_LOW]);
 641                        data->in_lsb[i][IN_MAX] = (lsb_max >> (2 * i)) & 0x03;
 642                        data->in_lsb[i][IN_LOW] = (lsb_low >> (2 * i)) & 0x03;
 643                }
 644        }
 645
 646        /* Update fan */
 647        for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
 648                if (!(data->has_fan & (1 << i)))
 649                        continue;
 650                data->fan[i] = w83795_read(client, W83795_REG_FAN(i)) << 4;
 651                data->fan[i] |= w83795_read(client, W83795_REG_VRLSB) >> 4;
 652        }
 653
 654        /* Update temperature */
 655        for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
 656                data->temp[i][TEMP_READ] =
 657                        w83795_read(client, W83795_REG_TEMP[i][TEMP_READ]);
 658                data->temp_read_vrlsb[i] =
 659                        w83795_read(client, W83795_REG_VRLSB);
 660        }
 661
 662        /* Update dts temperature */
 663        if (data->enable_dts) {
 664                for (i = 0; i < ARRAY_SIZE(data->dts); i++) {
 665                        if (!(data->has_dts & (1 << i)))
 666                                continue;
 667                        data->dts[i] =
 668                                w83795_read(client, W83795_REG_DTS(i));
 669                        data->dts_read_vrlsb[i] =
 670                                w83795_read(client, W83795_REG_VRLSB);
 671                }
 672        }
 673
 674        /* Update pwm output */
 675        for (i = 0; i < data->has_pwm; i++) {
 676                data->pwm[i][PWM_OUTPUT] =
 677                    w83795_read(client, W83795_REG_PWM(i, PWM_OUTPUT));
 678        }
 679
 680        /*
 681         * Update intrusion and alarms
 682         * It is important to read intrusion first, because reading from
 683         * register SMI STS6 clears the interrupt status temporarily.
 684         */
 685        tmp = w83795_read(client, W83795_REG_ALARM_CTRL);
 686        /* Switch to interrupt status for intrusion if needed */
 687        if (tmp & ALARM_CTRL_RTSACS)
 688                w83795_write(client, W83795_REG_ALARM_CTRL,
 689                             tmp & ~ALARM_CTRL_RTSACS);
 690        intrusion = w83795_read(client, W83795_REG_ALARM(5)) & (1 << 6);
 691        /* Switch to real-time alarms */
 692        w83795_write(client, W83795_REG_ALARM_CTRL, tmp | ALARM_CTRL_RTSACS);
 693        for (i = 0; i < ARRAY_SIZE(data->alarms); i++)
 694                data->alarms[i] = w83795_read(client, W83795_REG_ALARM(i));
 695        data->alarms[5] |= intrusion;
 696        /* Restore original configuration if needed */
 697        if (!(tmp & ALARM_CTRL_RTSACS))
 698                w83795_write(client, W83795_REG_ALARM_CTRL,
 699                             tmp & ~ALARM_CTRL_RTSACS);
 700
 701        data->last_updated = jiffies;
 702        data->valid = 1;
 703
 704END:
 705        mutex_unlock(&data->update_lock);
 706        return data;
 707}
 708
 709/*
 710 * Sysfs attributes
 711 */
 712
 713#define ALARM_STATUS      0
 714#define BEEP_ENABLE       1
 715static ssize_t
 716show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf)
 717{
 718        struct w83795_data *data = w83795_update_device(dev);
 719        struct sensor_device_attribute_2 *sensor_attr =
 720            to_sensor_dev_attr_2(attr);
 721        int nr = sensor_attr->nr;
 722        int index = sensor_attr->index >> 3;
 723        int bit = sensor_attr->index & 0x07;
 724        u8 val;
 725
 726        if (nr == ALARM_STATUS)
 727                val = (data->alarms[index] >> bit) & 1;
 728        else            /* BEEP_ENABLE */
 729                val = (data->beeps[index] >> bit) & 1;
 730
 731        return sprintf(buf, "%u\n", val);
 732}
 733
 734static ssize_t
 735store_beep(struct device *dev, struct device_attribute *attr,
 736           const char *buf, size_t count)
 737{
 738        struct i2c_client *client = to_i2c_client(dev);
 739        struct w83795_data *data = i2c_get_clientdata(client);
 740        struct sensor_device_attribute_2 *sensor_attr =
 741            to_sensor_dev_attr_2(attr);
 742        int index = sensor_attr->index >> 3;
 743        int shift = sensor_attr->index & 0x07;
 744        u8 beep_bit = 1 << shift;
 745        unsigned long val;
 746
 747        if (kstrtoul(buf, 10, &val) < 0)
 748                return -EINVAL;
 749        if (val != 0 && val != 1)
 750                return -EINVAL;
 751
 752        mutex_lock(&data->update_lock);
 753        data->beeps[index] = w83795_read(client, W83795_REG_BEEP(index));
 754        data->beeps[index] &= ~beep_bit;
 755        data->beeps[index] |= val << shift;
 756        w83795_write(client, W83795_REG_BEEP(index), data->beeps[index]);
 757        mutex_unlock(&data->update_lock);
 758
 759        return count;
 760}
 761
 762/* Write 0 to clear chassis alarm */
 763static ssize_t
 764store_chassis_clear(struct device *dev,
 765                    struct device_attribute *attr, const char *buf,
 766                    size_t count)
 767{
 768        struct i2c_client *client = to_i2c_client(dev);
 769        struct w83795_data *data = i2c_get_clientdata(client);
 770        unsigned long val;
 771
 772        if (kstrtoul(buf, 10, &val) < 0 || val != 0)
 773                return -EINVAL;
 774
 775        mutex_lock(&data->update_lock);
 776        val = w83795_read(client, W83795_REG_CLR_CHASSIS);
 777        val |= 0x80;
 778        w83795_write(client, W83795_REG_CLR_CHASSIS, val);
 779
 780        /* Clear status and force cache refresh */
 781        w83795_read(client, W83795_REG_ALARM(5));
 782        data->valid = 0;
 783        mutex_unlock(&data->update_lock);
 784        return count;
 785}
 786
 787#define FAN_INPUT     0
 788#define FAN_MIN       1
 789static ssize_t
 790show_fan(struct device *dev, struct device_attribute *attr, char *buf)
 791{
 792        struct sensor_device_attribute_2 *sensor_attr =
 793            to_sensor_dev_attr_2(attr);
 794        int nr = sensor_attr->nr;
 795        int index = sensor_attr->index;
 796        struct w83795_data *data = w83795_update_device(dev);
 797        u16 val;
 798
 799        if (nr == FAN_INPUT)
 800                val = data->fan[index] & 0x0fff;
 801        else
 802                val = data->fan_min[index] & 0x0fff;
 803
 804        return sprintf(buf, "%lu\n", fan_from_reg(val));
 805}
 806
 807static ssize_t
 808store_fan_min(struct device *dev, struct device_attribute *attr,
 809              const char *buf, size_t count)
 810{
 811        struct sensor_device_attribute_2 *sensor_attr =
 812            to_sensor_dev_attr_2(attr);
 813        int index = sensor_attr->index;
 814        struct i2c_client *client = to_i2c_client(dev);
 815        struct w83795_data *data = i2c_get_clientdata(client);
 816        unsigned long val;
 817
 818        if (kstrtoul(buf, 10, &val))
 819                return -EINVAL;
 820        val = fan_to_reg(val);
 821
 822        mutex_lock(&data->update_lock);
 823        data->fan_min[index] = val;
 824        w83795_write(client, W83795_REG_FAN_MIN_HL(index), (val >> 4) & 0xff);
 825        val &= 0x0f;
 826        if (index & 1) {
 827                val <<= 4;
 828                val |= w83795_read(client, W83795_REG_FAN_MIN_LSB(index))
 829                       & 0x0f;
 830        } else {
 831                val |= w83795_read(client, W83795_REG_FAN_MIN_LSB(index))
 832                       & 0xf0;
 833        }
 834        w83795_write(client, W83795_REG_FAN_MIN_LSB(index), val & 0xff);
 835        mutex_unlock(&data->update_lock);
 836
 837        return count;
 838}
 839
 840static ssize_t
 841show_pwm(struct device *dev, struct device_attribute *attr, char *buf)
 842{
 843        struct w83795_data *data;
 844        struct sensor_device_attribute_2 *sensor_attr =
 845            to_sensor_dev_attr_2(attr);
 846        int nr = sensor_attr->nr;
 847        int index = sensor_attr->index;
 848        unsigned int val;
 849
 850        data = nr == PWM_OUTPUT ? w83795_update_device(dev)
 851                                : w83795_update_pwm_config(dev);
 852
 853        switch (nr) {
 854        case PWM_STOP_TIME:
 855                val = time_from_reg(data->pwm[index][nr]);
 856                break;
 857        case PWM_FREQ:
 858                val = pwm_freq_from_reg(data->pwm[index][nr], data->clkin);
 859                break;
 860        default:
 861                val = data->pwm[index][nr];
 862                break;
 863        }
 864
 865        return sprintf(buf, "%u\n", val);
 866}
 867
 868static ssize_t
 869store_pwm(struct device *dev, struct device_attribute *attr,
 870          const char *buf, size_t count)
 871{
 872        struct i2c_client *client = to_i2c_client(dev);
 873        struct w83795_data *data = i2c_get_clientdata(client);
 874        struct sensor_device_attribute_2 *sensor_attr =
 875            to_sensor_dev_attr_2(attr);
 876        int nr = sensor_attr->nr;
 877        int index = sensor_attr->index;
 878        unsigned long val;
 879
 880        if (kstrtoul(buf, 10, &val) < 0)
 881                return -EINVAL;
 882
 883        mutex_lock(&data->update_lock);
 884        switch (nr) {
 885        case PWM_STOP_TIME:
 886                val = time_to_reg(val);
 887                break;
 888        case PWM_FREQ:
 889                val = pwm_freq_to_reg(val, data->clkin);
 890                break;
 891        default:
 892                val = clamp_val(val, 0, 0xff);
 893                break;
 894        }
 895        w83795_write(client, W83795_REG_PWM(index, nr), val);
 896        data->pwm[index][nr] = val;
 897        mutex_unlock(&data->update_lock);
 898        return count;
 899}
 900
 901static ssize_t
 902show_pwm_enable(struct device *dev, struct device_attribute *attr, char *buf)
 903{
 904        struct sensor_device_attribute_2 *sensor_attr =
 905            to_sensor_dev_attr_2(attr);
 906        struct w83795_data *data = w83795_update_pwm_config(dev);
 907        int index = sensor_attr->index;
 908        u8 tmp;
 909
 910        /* Speed cruise mode */
 911        if (data->pwm_fcms[0] & (1 << index)) {
 912                tmp = 2;
 913                goto out;
 914        }
 915        /* Thermal cruise or SmartFan IV mode */
 916        for (tmp = 0; tmp < 6; tmp++) {
 917                if (data->pwm_tfmr[tmp] & (1 << index)) {
 918                        tmp = 3;
 919                        goto out;
 920                }
 921        }
 922        /* Manual mode */
 923        tmp = 1;
 924
 925out:
 926        return sprintf(buf, "%u\n", tmp);
 927}
 928
 929static ssize_t
 930store_pwm_enable(struct device *dev, struct device_attribute *attr,
 931          const char *buf, size_t count)
 932{
 933        struct i2c_client *client = to_i2c_client(dev);
 934        struct w83795_data *data = w83795_update_pwm_config(dev);
 935        struct sensor_device_attribute_2 *sensor_attr =
 936            to_sensor_dev_attr_2(attr);
 937        int index = sensor_attr->index;
 938        unsigned long val;
 939        int i;
 940
 941        if (kstrtoul(buf, 10, &val) < 0)
 942                return -EINVAL;
 943        if (val < 1 || val > 2)
 944                return -EINVAL;
 945
 946#ifndef CONFIG_SENSORS_W83795_FANCTRL
 947        if (val > 1) {
 948                dev_warn(dev, "Automatic fan speed control support disabled\n");
 949                dev_warn(dev, "Build with CONFIG_SENSORS_W83795_FANCTRL=y if you want it\n");
 950                return -EOPNOTSUPP;
 951        }
 952#endif
 953
 954        mutex_lock(&data->update_lock);
 955        switch (val) {
 956        case 1:
 957                /* Clear speed cruise mode bits */
 958                data->pwm_fcms[0] &= ~(1 << index);
 959                w83795_write(client, W83795_REG_FCMS1, data->pwm_fcms[0]);
 960                /* Clear thermal cruise mode bits */
 961                for (i = 0; i < 6; i++) {
 962                        data->pwm_tfmr[i] &= ~(1 << index);
 963                        w83795_write(client, W83795_REG_TFMR(i),
 964                                data->pwm_tfmr[i]);
 965                }
 966                break;
 967        case 2:
 968                data->pwm_fcms[0] |= (1 << index);
 969                w83795_write(client, W83795_REG_FCMS1, data->pwm_fcms[0]);
 970                break;
 971        }
 972        mutex_unlock(&data->update_lock);
 973        return count;
 974}
 975
 976static ssize_t
 977show_pwm_mode(struct device *dev, struct device_attribute *attr, char *buf)
 978{
 979        struct w83795_data *data = w83795_update_pwm_config(dev);
 980        int index = to_sensor_dev_attr_2(attr)->index;
 981        unsigned int mode;
 982
 983        if (data->pwm_fomc & (1 << index))
 984                mode = 0;       /* DC */
 985        else
 986                mode = 1;       /* PWM */
 987
 988        return sprintf(buf, "%u\n", mode);
 989}
 990
 991/*
 992 * Check whether a given temperature source can ever be useful.
 993 * Returns the number of selectable temperature channels which are
 994 * enabled.
 995 */
 996static int w83795_tss_useful(const struct w83795_data *data, int tsrc)
 997{
 998        int useful = 0, i;
 999
1000        for (i = 0; i < 4; i++) {
1001                if (tss_map[i][tsrc] == TSS_MAP_RESERVED)
1002                        continue;
1003                if (tss_map[i][tsrc] < 6)       /* Analog */
1004                        useful += (data->has_temp >> tss_map[i][tsrc]) & 1;
1005                else                            /* Digital */
1006                        useful += (data->has_dts >> (tss_map[i][tsrc] - 6)) & 1;
1007        }
1008
1009        return useful;
1010}
1011
1012static ssize_t
1013show_temp_src(struct device *dev, struct device_attribute *attr, char *buf)
1014{
1015        struct sensor_device_attribute_2 *sensor_attr =
1016            to_sensor_dev_attr_2(attr);
1017        struct w83795_data *data = w83795_update_pwm_config(dev);
1018        int index = sensor_attr->index;
1019        u8 tmp = data->temp_src[index / 2];
1020
1021        if (index & 1)
1022                tmp >>= 4;      /* Pick high nibble */
1023        else
1024                tmp &= 0x0f;    /* Pick low nibble */
1025
1026        /* Look-up the actual temperature channel number */
1027        if (tmp >= 4 || tss_map[tmp][index] == TSS_MAP_RESERVED)
1028                return -EINVAL;         /* Shouldn't happen */
1029
1030        return sprintf(buf, "%u\n", (unsigned int)tss_map[tmp][index] + 1);
1031}
1032
1033static ssize_t
1034store_temp_src(struct device *dev, struct device_attribute *attr,
1035          const char *buf, size_t count)
1036{
1037        struct i2c_client *client = to_i2c_client(dev);
1038        struct w83795_data *data = w83795_update_pwm_config(dev);
1039        struct sensor_device_attribute_2 *sensor_attr =
1040            to_sensor_dev_attr_2(attr);
1041        int index = sensor_attr->index;
1042        int tmp;
1043        unsigned long channel;
1044        u8 val = index / 2;
1045
1046        if (kstrtoul(buf, 10, &channel) < 0 ||
1047            channel < 1 || channel > 14)
1048                return -EINVAL;
1049
1050        /* Check if request can be fulfilled */
1051        for (tmp = 0; tmp < 4; tmp++) {
1052                if (tss_map[tmp][index] == channel - 1)
1053                        break;
1054        }
1055        if (tmp == 4)   /* No match */
1056                return -EINVAL;
1057
1058        mutex_lock(&data->update_lock);
1059        if (index & 1) {
1060                tmp <<= 4;
1061                data->temp_src[val] &= 0x0f;
1062        } else {
1063                data->temp_src[val] &= 0xf0;
1064        }
1065        data->temp_src[val] |= tmp;
1066        w83795_write(client, W83795_REG_TSS(val), data->temp_src[val]);
1067        mutex_unlock(&data->update_lock);
1068
1069        return count;
1070}
1071
1072#define TEMP_PWM_ENABLE   0
1073#define TEMP_PWM_FAN_MAP  1
1074static ssize_t
1075show_temp_pwm_enable(struct device *dev, struct device_attribute *attr,
1076                     char *buf)
1077{
1078        struct w83795_data *data = w83795_update_pwm_config(dev);
1079        struct sensor_device_attribute_2 *sensor_attr =
1080            to_sensor_dev_attr_2(attr);
1081        int nr = sensor_attr->nr;
1082        int index = sensor_attr->index;
1083        u8 tmp = 0xff;
1084
1085        switch (nr) {
1086        case TEMP_PWM_ENABLE:
1087                tmp = (data->pwm_fcms[1] >> index) & 1;
1088                if (tmp)
1089                        tmp = 4;
1090                else
1091                        tmp = 3;
1092                break;
1093        case TEMP_PWM_FAN_MAP:
1094                tmp = data->pwm_tfmr[index];
1095                break;
1096        }
1097
1098        return sprintf(buf, "%u\n", tmp);
1099}
1100
1101static ssize_t
1102store_temp_pwm_enable(struct device *dev, struct device_attribute *attr,
1103          const char *buf, size_t count)
1104{
1105        struct i2c_client *client = to_i2c_client(dev);
1106        struct w83795_data *data = w83795_update_pwm_config(dev);
1107        struct sensor_device_attribute_2 *sensor_attr =
1108            to_sensor_dev_attr_2(attr);
1109        int nr = sensor_attr->nr;
1110        int index = sensor_attr->index;
1111        unsigned long tmp;
1112
1113        if (kstrtoul(buf, 10, &tmp) < 0)
1114                return -EINVAL;
1115
1116        switch (nr) {
1117        case TEMP_PWM_ENABLE:
1118                if (tmp != 3 && tmp != 4)
1119                        return -EINVAL;
1120                tmp -= 3;
1121                mutex_lock(&data->update_lock);
1122                data->pwm_fcms[1] &= ~(1 << index);
1123                data->pwm_fcms[1] |= tmp << index;
1124                w83795_write(client, W83795_REG_FCMS2, data->pwm_fcms[1]);
1125                mutex_unlock(&data->update_lock);
1126                break;
1127        case TEMP_PWM_FAN_MAP:
1128                mutex_lock(&data->update_lock);
1129                tmp = clamp_val(tmp, 0, 0xff);
1130                w83795_write(client, W83795_REG_TFMR(index), tmp);
1131                data->pwm_tfmr[index] = tmp;
1132                mutex_unlock(&data->update_lock);
1133                break;
1134        }
1135        return count;
1136}
1137
1138#define FANIN_TARGET   0
1139#define FANIN_TOL      1
1140static ssize_t
1141show_fanin(struct device *dev, struct device_attribute *attr, char *buf)
1142{
1143        struct w83795_data *data = w83795_update_pwm_config(dev);
1144        struct sensor_device_attribute_2 *sensor_attr =
1145            to_sensor_dev_attr_2(attr);
1146        int nr = sensor_attr->nr;
1147        int index = sensor_attr->index;
1148        u16 tmp = 0;
1149
1150        switch (nr) {
1151        case FANIN_TARGET:
1152                tmp = fan_from_reg(data->target_speed[index]);
1153                break;
1154        case FANIN_TOL:
1155                tmp = data->tol_speed;
1156                break;
1157        }
1158
1159        return sprintf(buf, "%u\n", tmp);
1160}
1161
1162static ssize_t
1163store_fanin(struct device *dev, struct device_attribute *attr,
1164          const char *buf, size_t count)
1165{
1166        struct i2c_client *client = to_i2c_client(dev);
1167        struct w83795_data *data = i2c_get_clientdata(client);
1168        struct sensor_device_attribute_2 *sensor_attr =
1169            to_sensor_dev_attr_2(attr);
1170        int nr = sensor_attr->nr;
1171        int index = sensor_attr->index;
1172        unsigned long val;
1173
1174        if (kstrtoul(buf, 10, &val) < 0)
1175                return -EINVAL;
1176
1177        mutex_lock(&data->update_lock);
1178        switch (nr) {
1179        case FANIN_TARGET:
1180                val = fan_to_reg(clamp_val(val, 0, 0xfff));
1181                w83795_write(client, W83795_REG_FTSH(index), val >> 4);
1182                w83795_write(client, W83795_REG_FTSL(index), (val << 4) & 0xf0);
1183                data->target_speed[index] = val;
1184                break;
1185        case FANIN_TOL:
1186                val = clamp_val(val, 0, 0x3f);
1187                w83795_write(client, W83795_REG_TFTS, val);
1188                data->tol_speed = val;
1189                break;
1190        }
1191        mutex_unlock(&data->update_lock);
1192
1193        return count;
1194}
1195
1196
1197static ssize_t
1198show_temp_pwm(struct device *dev, struct device_attribute *attr, char *buf)
1199{
1200        struct w83795_data *data = w83795_update_pwm_config(dev);
1201        struct sensor_device_attribute_2 *sensor_attr =
1202            to_sensor_dev_attr_2(attr);
1203        int nr = sensor_attr->nr;
1204        int index = sensor_attr->index;
1205        long tmp = temp_from_reg(data->pwm_temp[index][nr]);
1206
1207        return sprintf(buf, "%ld\n", tmp);
1208}
1209
1210static ssize_t
1211store_temp_pwm(struct device *dev, struct device_attribute *attr,
1212          const char *buf, size_t count)
1213{
1214        struct i2c_client *client = to_i2c_client(dev);
1215        struct w83795_data *data = i2c_get_clientdata(client);
1216        struct sensor_device_attribute_2 *sensor_attr =
1217            to_sensor_dev_attr_2(attr);
1218        int nr = sensor_attr->nr;
1219        int index = sensor_attr->index;
1220        unsigned long val;
1221        u8 tmp;
1222
1223        if (kstrtoul(buf, 10, &val) < 0)
1224                return -EINVAL;
1225        val /= 1000;
1226
1227        mutex_lock(&data->update_lock);
1228        switch (nr) {
1229        case TEMP_PWM_TTTI:
1230                val = clamp_val(val, 0, 0x7f);
1231                w83795_write(client, W83795_REG_TTTI(index), val);
1232                break;
1233        case TEMP_PWM_CTFS:
1234                val = clamp_val(val, 0, 0x7f);
1235                w83795_write(client, W83795_REG_CTFS(index), val);
1236                break;
1237        case TEMP_PWM_HCT:
1238                val = clamp_val(val, 0, 0x0f);
1239                tmp = w83795_read(client, W83795_REG_HT(index));
1240                tmp &= 0x0f;
1241                tmp |= (val << 4) & 0xf0;
1242                w83795_write(client, W83795_REG_HT(index), tmp);
1243                break;
1244        case TEMP_PWM_HOT:
1245                val = clamp_val(val, 0, 0x0f);
1246                tmp = w83795_read(client, W83795_REG_HT(index));
1247                tmp &= 0xf0;
1248                tmp |= val & 0x0f;
1249                w83795_write(client, W83795_REG_HT(index), tmp);
1250                break;
1251        }
1252        data->pwm_temp[index][nr] = val;
1253        mutex_unlock(&data->update_lock);
1254
1255        return count;
1256}
1257
1258static ssize_t
1259show_sf4_pwm(struct device *dev, struct device_attribute *attr, char *buf)
1260{
1261        struct w83795_data *data = w83795_update_pwm_config(dev);
1262        struct sensor_device_attribute_2 *sensor_attr =
1263            to_sensor_dev_attr_2(attr);
1264        int nr = sensor_attr->nr;
1265        int index = sensor_attr->index;
1266
1267        return sprintf(buf, "%u\n", data->sf4_reg[index][SF4_PWM][nr]);
1268}
1269
1270static ssize_t
1271store_sf4_pwm(struct device *dev, struct device_attribute *attr,
1272          const char *buf, size_t count)
1273{
1274        struct i2c_client *client = to_i2c_client(dev);
1275        struct w83795_data *data = i2c_get_clientdata(client);
1276        struct sensor_device_attribute_2 *sensor_attr =
1277            to_sensor_dev_attr_2(attr);
1278        int nr = sensor_attr->nr;
1279        int index = sensor_attr->index;
1280        unsigned long val;
1281
1282        if (kstrtoul(buf, 10, &val) < 0)
1283                return -EINVAL;
1284
1285        mutex_lock(&data->update_lock);
1286        w83795_write(client, W83795_REG_SF4_PWM(index, nr), val);
1287        data->sf4_reg[index][SF4_PWM][nr] = val;
1288        mutex_unlock(&data->update_lock);
1289
1290        return count;
1291}
1292
1293static ssize_t
1294show_sf4_temp(struct device *dev, struct device_attribute *attr, char *buf)
1295{
1296        struct w83795_data *data = w83795_update_pwm_config(dev);
1297        struct sensor_device_attribute_2 *sensor_attr =
1298            to_sensor_dev_attr_2(attr);
1299        int nr = sensor_attr->nr;
1300        int index = sensor_attr->index;
1301
1302        return sprintf(buf, "%u\n",
1303                (data->sf4_reg[index][SF4_TEMP][nr]) * 1000);
1304}
1305
1306static ssize_t
1307store_sf4_temp(struct device *dev, struct device_attribute *attr,
1308          const char *buf, size_t count)
1309{
1310        struct i2c_client *client = to_i2c_client(dev);
1311        struct w83795_data *data = i2c_get_clientdata(client);
1312        struct sensor_device_attribute_2 *sensor_attr =
1313            to_sensor_dev_attr_2(attr);
1314        int nr = sensor_attr->nr;
1315        int index = sensor_attr->index;
1316        unsigned long val;
1317
1318        if (kstrtoul(buf, 10, &val) < 0)
1319                return -EINVAL;
1320        val /= 1000;
1321
1322        mutex_lock(&data->update_lock);
1323        w83795_write(client, W83795_REG_SF4_TEMP(index, nr), val);
1324        data->sf4_reg[index][SF4_TEMP][nr] = val;
1325        mutex_unlock(&data->update_lock);
1326
1327        return count;
1328}
1329
1330
1331static ssize_t
1332show_temp(struct device *dev, struct device_attribute *attr, char *buf)
1333{
1334        struct sensor_device_attribute_2 *sensor_attr =
1335            to_sensor_dev_attr_2(attr);
1336        int nr = sensor_attr->nr;
1337        int index = sensor_attr->index;
1338        struct w83795_data *data = w83795_update_device(dev);
1339        long temp = temp_from_reg(data->temp[index][nr]);
1340
1341        if (nr == TEMP_READ)
1342                temp += (data->temp_read_vrlsb[index] >> 6) * 250;
1343        return sprintf(buf, "%ld\n", temp);
1344}
1345
1346static ssize_t
1347store_temp(struct device *dev, struct device_attribute *attr,
1348           const char *buf, size_t count)
1349{
1350        struct sensor_device_attribute_2 *sensor_attr =
1351            to_sensor_dev_attr_2(attr);
1352        int nr = sensor_attr->nr;
1353        int index = sensor_attr->index;
1354        struct i2c_client *client = to_i2c_client(dev);
1355        struct w83795_data *data = i2c_get_clientdata(client);
1356        long tmp;
1357
1358        if (kstrtol(buf, 10, &tmp) < 0)
1359                return -EINVAL;
1360
1361        mutex_lock(&data->update_lock);
1362        data->temp[index][nr] = temp_to_reg(tmp, -128, 127);
1363        w83795_write(client, W83795_REG_TEMP[index][nr], data->temp[index][nr]);
1364        mutex_unlock(&data->update_lock);
1365        return count;
1366}
1367
1368
1369static ssize_t
1370show_dts_mode(struct device *dev, struct device_attribute *attr, char *buf)
1371{
1372        struct w83795_data *data = dev_get_drvdata(dev);
1373        int tmp;
1374
1375        if (data->enable_dts & 2)
1376                tmp = 5;
1377        else
1378                tmp = 6;
1379
1380        return sprintf(buf, "%d\n", tmp);
1381}
1382
1383static ssize_t
1384show_dts(struct device *dev, struct device_attribute *attr, char *buf)
1385{
1386        struct sensor_device_attribute_2 *sensor_attr =
1387            to_sensor_dev_attr_2(attr);
1388        int index = sensor_attr->index;
1389        struct w83795_data *data = w83795_update_device(dev);
1390        long temp = temp_from_reg(data->dts[index]);
1391
1392        temp += (data->dts_read_vrlsb[index] >> 6) * 250;
1393        return sprintf(buf, "%ld\n", temp);
1394}
1395
1396static ssize_t
1397show_dts_ext(struct device *dev, struct device_attribute *attr, char *buf)
1398{
1399        struct sensor_device_attribute_2 *sensor_attr =
1400            to_sensor_dev_attr_2(attr);
1401        int nr = sensor_attr->nr;
1402        struct w83795_data *data = dev_get_drvdata(dev);
1403        long temp = temp_from_reg(data->dts_ext[nr]);
1404
1405        return sprintf(buf, "%ld\n", temp);
1406}
1407
1408static ssize_t
1409store_dts_ext(struct device *dev, struct device_attribute *attr,
1410           const char *buf, size_t count)
1411{
1412        struct sensor_device_attribute_2 *sensor_attr =
1413            to_sensor_dev_attr_2(attr);
1414        int nr = sensor_attr->nr;
1415        struct i2c_client *client = to_i2c_client(dev);
1416        struct w83795_data *data = i2c_get_clientdata(client);
1417        long tmp;
1418
1419        if (kstrtol(buf, 10, &tmp) < 0)
1420                return -EINVAL;
1421
1422        mutex_lock(&data->update_lock);
1423        data->dts_ext[nr] = temp_to_reg(tmp, -128, 127);
1424        w83795_write(client, W83795_REG_DTS_EXT(nr), data->dts_ext[nr]);
1425        mutex_unlock(&data->update_lock);
1426        return count;
1427}
1428
1429
1430static ssize_t
1431show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf)
1432{
1433        struct w83795_data *data = dev_get_drvdata(dev);
1434        struct sensor_device_attribute_2 *sensor_attr =
1435            to_sensor_dev_attr_2(attr);
1436        int index = sensor_attr->index;
1437        int tmp;
1438
1439        if (data->temp_mode & (1 << index))
1440                tmp = 3;        /* Thermal diode */
1441        else
1442                tmp = 4;        /* Thermistor */
1443
1444        return sprintf(buf, "%d\n", tmp);
1445}
1446
1447/* Only for temp1-4 (temp5-6 can only be thermistor) */
1448static ssize_t
1449store_temp_mode(struct device *dev, struct device_attribute *attr,
1450                const char *buf, size_t count)
1451{
1452        struct i2c_client *client = to_i2c_client(dev);
1453        struct w83795_data *data = i2c_get_clientdata(client);
1454        struct sensor_device_attribute_2 *sensor_attr =
1455            to_sensor_dev_attr_2(attr);
1456        int index = sensor_attr->index;
1457        int reg_shift;
1458        unsigned long val;
1459        u8 tmp;
1460
1461        if (kstrtoul(buf, 10, &val) < 0)
1462                return -EINVAL;
1463        if ((val != 4) && (val != 3))
1464                return -EINVAL;
1465
1466        mutex_lock(&data->update_lock);
1467        if (val == 3) {
1468                /* Thermal diode */
1469                val = 0x01;
1470                data->temp_mode |= 1 << index;
1471        } else if (val == 4) {
1472                /* Thermistor */
1473                val = 0x03;
1474                data->temp_mode &= ~(1 << index);
1475        }
1476
1477        reg_shift = 2 * index;
1478        tmp = w83795_read(client, W83795_REG_TEMP_CTRL2);
1479        tmp &= ~(0x03 << reg_shift);
1480        tmp |= val << reg_shift;
1481        w83795_write(client, W83795_REG_TEMP_CTRL2, tmp);
1482
1483        mutex_unlock(&data->update_lock);
1484        return count;
1485}
1486
1487
1488/* show/store VIN */
1489static ssize_t
1490show_in(struct device *dev, struct device_attribute *attr, char *buf)
1491{
1492        struct sensor_device_attribute_2 *sensor_attr =
1493            to_sensor_dev_attr_2(attr);
1494        int nr = sensor_attr->nr;
1495        int index = sensor_attr->index;
1496        struct w83795_data *data = w83795_update_device(dev);
1497        u16 val = data->in[index][nr];
1498        u8 lsb_idx;
1499
1500        switch (nr) {
1501        case IN_READ:
1502                /* calculate this value again by sensors as sensors3.conf */
1503                if ((index >= 17) &&
1504                    !((data->has_gain >> (index - 17)) & 1))
1505                        val *= 8;
1506                break;
1507        case IN_MAX:
1508        case IN_LOW:
1509                lsb_idx = IN_LSB_SHIFT_IDX[index][IN_LSB_IDX];
1510                val <<= 2;
1511                val |= (data->in_lsb[lsb_idx][nr] >>
1512                        IN_LSB_SHIFT_IDX[index][IN_LSB_SHIFT]) & 0x03;
1513                if ((index >= 17) &&
1514                    !((data->has_gain >> (index - 17)) & 1))
1515                        val *= 8;
1516                break;
1517        }
1518        val = in_from_reg(index, val);
1519
1520        return sprintf(buf, "%d\n", val);
1521}
1522
1523static ssize_t
1524store_in(struct device *dev, struct device_attribute *attr,
1525         const char *buf, size_t count)
1526{
1527        struct sensor_device_attribute_2 *sensor_attr =
1528            to_sensor_dev_attr_2(attr);
1529        int nr = sensor_attr->nr;
1530        int index = sensor_attr->index;
1531        struct i2c_client *client = to_i2c_client(dev);
1532        struct w83795_data *data = i2c_get_clientdata(client);
1533        unsigned long val;
1534        u8 tmp;
1535        u8 lsb_idx;
1536
1537        if (kstrtoul(buf, 10, &val) < 0)
1538                return -EINVAL;
1539        val = in_to_reg(index, val);
1540
1541        if ((index >= 17) &&
1542            !((data->has_gain >> (index - 17)) & 1))
1543                val /= 8;
1544        val = clamp_val(val, 0, 0x3FF);
1545        mutex_lock(&data->update_lock);
1546
1547        lsb_idx = IN_LSB_SHIFT_IDX[index][IN_LSB_IDX];
1548        tmp = w83795_read(client, IN_LSB_REG(lsb_idx, nr));
1549        tmp &= ~(0x03 << IN_LSB_SHIFT_IDX[index][IN_LSB_SHIFT]);
1550        tmp |= (val & 0x03) << IN_LSB_SHIFT_IDX[index][IN_LSB_SHIFT];
1551        w83795_write(client, IN_LSB_REG(lsb_idx, nr), tmp);
1552        data->in_lsb[lsb_idx][nr] = tmp;
1553
1554        tmp = (val >> 2) & 0xff;
1555        w83795_write(client, W83795_REG_IN[index][nr], tmp);
1556        data->in[index][nr] = tmp;
1557
1558        mutex_unlock(&data->update_lock);
1559        return count;
1560}
1561
1562
1563#ifdef CONFIG_SENSORS_W83795_FANCTRL
1564static ssize_t
1565show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf)
1566{
1567        struct sensor_device_attribute_2 *sensor_attr =
1568            to_sensor_dev_attr_2(attr);
1569        int nr = sensor_attr->nr;
1570        struct w83795_data *data = w83795_update_pwm_config(dev);
1571        u16 val = data->setup_pwm[nr];
1572
1573        switch (nr) {
1574        case SETUP_PWM_UPTIME:
1575        case SETUP_PWM_DOWNTIME:
1576                val = time_from_reg(val);
1577                break;
1578        }
1579
1580        return sprintf(buf, "%d\n", val);
1581}
1582
1583static ssize_t
1584store_sf_setup(struct device *dev, struct device_attribute *attr,
1585         const char *buf, size_t count)
1586{
1587        struct sensor_device_attribute_2 *sensor_attr =
1588            to_sensor_dev_attr_2(attr);
1589        int nr = sensor_attr->nr;
1590        struct i2c_client *client = to_i2c_client(dev);
1591        struct w83795_data *data = i2c_get_clientdata(client);
1592        unsigned long val;
1593
1594        if (kstrtoul(buf, 10, &val) < 0)
1595                return -EINVAL;
1596
1597        switch (nr) {
1598        case SETUP_PWM_DEFAULT:
1599                val = clamp_val(val, 0, 0xff);
1600                break;
1601        case SETUP_PWM_UPTIME:
1602        case SETUP_PWM_DOWNTIME:
1603                val = time_to_reg(val);
1604                if (val == 0)
1605                        return -EINVAL;
1606                break;
1607        }
1608
1609        mutex_lock(&data->update_lock);
1610        data->setup_pwm[nr] = val;
1611        w83795_write(client, W83795_REG_SETUP_PWM(nr), val);
1612        mutex_unlock(&data->update_lock);
1613        return count;
1614}
1615#endif
1616
1617
1618#define NOT_USED                        -1
1619
1620/*
1621 * Don't change the attribute order, _max, _min and _beep are accessed by index
1622 * somewhere else in the code
1623 */
1624#define SENSOR_ATTR_IN(index) {                                         \
1625        SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL,        \
1626                IN_READ, index), \
1627        SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in,      \
1628                store_in, IN_MAX, index),                               \
1629        SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in,      \
1630                store_in, IN_LOW, index),                               \
1631        SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep,      \
1632                NULL, ALARM_STATUS, index + ((index > 14) ? 1 : 0)), \
1633        SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO,              \
1634                show_alarm_beep, store_beep, BEEP_ENABLE,               \
1635                index + ((index > 14) ? 1 : 0)) }
1636
1637/*
1638 * Don't change the attribute order, _beep is accessed by index
1639 * somewhere else in the code
1640 */
1641#define SENSOR_ATTR_FAN(index) {                                        \
1642        SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan,            \
1643                NULL, FAN_INPUT, index - 1), \
1644        SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO,              \
1645                show_fan, store_fan_min, FAN_MIN, index - 1),   \
1646        SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep,     \
1647                NULL, ALARM_STATUS, index + 31),                        \
1648        SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO,             \
1649                show_alarm_beep, store_beep, BEEP_ENABLE, index + 31) }
1650
1651#define SENSOR_ATTR_PWM(index) {                                        \
1652        SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm,          \
1653                store_pwm, PWM_OUTPUT, index - 1),                      \
1654        SENSOR_ATTR_2(pwm##index##_enable, S_IWUSR | S_IRUGO,           \
1655                show_pwm_enable, store_pwm_enable, NOT_USED, index - 1), \
1656        SENSOR_ATTR_2(pwm##index##_mode, S_IRUGO,                       \
1657                show_pwm_mode, NULL, NOT_USED, index - 1),              \
1658        SENSOR_ATTR_2(pwm##index##_freq, S_IWUSR | S_IRUGO,             \
1659                show_pwm, store_pwm, PWM_FREQ, index - 1),              \
1660        SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO,          \
1661                show_pwm, store_pwm, PWM_NONSTOP, index - 1),           \
1662        SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO,            \
1663                show_pwm, store_pwm, PWM_START, index - 1),             \
1664        SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO,        \
1665                show_pwm, store_pwm, PWM_STOP_TIME, index - 1),  \
1666        SENSOR_ATTR_2(fan##index##_target, S_IWUSR | S_IRUGO, \
1667                show_fanin, store_fanin, FANIN_TARGET, index - 1) }
1668
1669/*
1670 * Don't change the attribute order, _beep is accessed by index
1671 * somewhere else in the code
1672 */
1673#define SENSOR_ATTR_DTS(index) {                                        \
1674        SENSOR_ATTR_2(temp##index##_type, S_IRUGO ,             \
1675                show_dts_mode, NULL, NOT_USED, index - 7),      \
1676        SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_dts,           \
1677                NULL, NOT_USED, index - 7),                             \
1678        SENSOR_ATTR_2(temp##index##_crit, S_IRUGO | S_IWUSR, show_dts_ext, \
1679                store_dts_ext, DTS_CRIT, NOT_USED),                     \
1680        SENSOR_ATTR_2(temp##index##_crit_hyst, S_IRUGO | S_IWUSR,       \
1681                show_dts_ext, store_dts_ext, DTS_CRIT_HYST, NOT_USED),  \
1682        SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_dts_ext, \
1683                store_dts_ext, DTS_WARN, NOT_USED),                     \
1684        SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR,        \
1685                show_dts_ext, store_dts_ext, DTS_WARN_HYST, NOT_USED),  \
1686        SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO,                     \
1687                show_alarm_beep, NULL, ALARM_STATUS, index + 17),       \
1688        SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO,            \
1689                show_alarm_beep, store_beep, BEEP_ENABLE, index + 17) }
1690
1691/*
1692 * Don't change the attribute order, _beep is accessed by index
1693 * somewhere else in the code
1694 */
1695#define SENSOR_ATTR_TEMP(index) {                                       \
1696        SENSOR_ATTR_2(temp##index##_type, S_IRUGO | (index < 4 ? S_IWUSR : 0), \
1697                show_temp_mode, store_temp_mode, NOT_USED, index - 1),  \
1698        SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp,          \
1699                NULL, TEMP_READ, index - 1),                            \
1700        SENSOR_ATTR_2(temp##index##_crit, S_IRUGO | S_IWUSR, show_temp, \
1701                store_temp, TEMP_CRIT, index - 1),                      \
1702        SENSOR_ATTR_2(temp##index##_crit_hyst, S_IRUGO | S_IWUSR,       \
1703                show_temp, store_temp, TEMP_CRIT_HYST, index - 1),      \
1704        SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp,  \
1705                store_temp, TEMP_WARN, index - 1),                      \
1706        SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR,        \
1707                show_temp, store_temp, TEMP_WARN_HYST, index - 1),      \
1708        SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO,                     \
1709                show_alarm_beep, NULL, ALARM_STATUS,                    \
1710                index + (index > 4 ? 11 : 17)),                         \
1711        SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO,            \
1712                show_alarm_beep, store_beep, BEEP_ENABLE,               \
1713                index + (index > 4 ? 11 : 17)),                         \
1714        SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO,      \
1715                show_temp_pwm_enable, store_temp_pwm_enable,            \
1716                TEMP_PWM_ENABLE, index - 1),                            \
1717        SENSOR_ATTR_2(temp##index##_auto_channels_pwm, S_IWUSR | S_IRUGO, \
1718                show_temp_pwm_enable, store_temp_pwm_enable,            \
1719                TEMP_PWM_FAN_MAP, index - 1),                           \
1720        SENSOR_ATTR_2(thermal_cruise##index, S_IWUSR | S_IRUGO,         \
1721                show_temp_pwm, store_temp_pwm, TEMP_PWM_TTTI, index - 1), \
1722        SENSOR_ATTR_2(temp##index##_warn, S_IWUSR | S_IRUGO,            \
1723                show_temp_pwm, store_temp_pwm, TEMP_PWM_CTFS, index - 1), \
1724        SENSOR_ATTR_2(temp##index##_warn_hyst, S_IWUSR | S_IRUGO,       \
1725                show_temp_pwm, store_temp_pwm, TEMP_PWM_HCT, index - 1), \
1726        SENSOR_ATTR_2(temp##index##_operation_hyst, S_IWUSR | S_IRUGO,  \
1727                show_temp_pwm, store_temp_pwm, TEMP_PWM_HOT, index - 1), \
1728        SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \
1729                show_sf4_pwm, store_sf4_pwm, 0, index - 1),             \
1730        SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \
1731                show_sf4_pwm, store_sf4_pwm, 1, index - 1),             \
1732        SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \
1733                show_sf4_pwm, store_sf4_pwm, 2, index - 1),             \
1734        SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \
1735                show_sf4_pwm, store_sf4_pwm, 3, index - 1),             \
1736        SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \
1737                show_sf4_pwm, store_sf4_pwm, 4, index - 1),             \
1738        SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \
1739                show_sf4_pwm, store_sf4_pwm, 5, index - 1),             \
1740        SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \
1741                show_sf4_pwm, store_sf4_pwm, 6, index - 1),             \
1742        SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\
1743                show_sf4_temp, store_sf4_temp, 0, index - 1),           \
1744        SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\
1745                show_sf4_temp, store_sf4_temp, 1, index - 1),           \
1746        SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\
1747                show_sf4_temp, store_sf4_temp, 2, index - 1),           \
1748        SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\
1749                show_sf4_temp, store_sf4_temp, 3, index - 1),           \
1750        SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\
1751                show_sf4_temp, store_sf4_temp, 4, index - 1),           \
1752        SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\
1753                show_sf4_temp, store_sf4_temp, 5, index - 1),           \
1754        SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\
1755                show_sf4_temp, store_sf4_temp, 6, index - 1) }
1756
1757
1758static struct sensor_device_attribute_2 w83795_in[][5] = {
1759        SENSOR_ATTR_IN(0),
1760        SENSOR_ATTR_IN(1),
1761        SENSOR_ATTR_IN(2),
1762        SENSOR_ATTR_IN(3),
1763        SENSOR_ATTR_IN(4),
1764        SENSOR_ATTR_IN(5),
1765        SENSOR_ATTR_IN(6),
1766        SENSOR_ATTR_IN(7),
1767        SENSOR_ATTR_IN(8),
1768        SENSOR_ATTR_IN(9),
1769        SENSOR_ATTR_IN(10),
1770        SENSOR_ATTR_IN(11),
1771        SENSOR_ATTR_IN(12),
1772        SENSOR_ATTR_IN(13),
1773        SENSOR_ATTR_IN(14),
1774        SENSOR_ATTR_IN(15),
1775        SENSOR_ATTR_IN(16),
1776        SENSOR_ATTR_IN(17),
1777        SENSOR_ATTR_IN(18),
1778        SENSOR_ATTR_IN(19),
1779        SENSOR_ATTR_IN(20),
1780};
1781
1782static const struct sensor_device_attribute_2 w83795_fan[][4] = {
1783        SENSOR_ATTR_FAN(1),
1784        SENSOR_ATTR_FAN(2),
1785        SENSOR_ATTR_FAN(3),
1786        SENSOR_ATTR_FAN(4),
1787        SENSOR_ATTR_FAN(5),
1788        SENSOR_ATTR_FAN(6),
1789        SENSOR_ATTR_FAN(7),
1790        SENSOR_ATTR_FAN(8),
1791        SENSOR_ATTR_FAN(9),
1792        SENSOR_ATTR_FAN(10),
1793        SENSOR_ATTR_FAN(11),
1794        SENSOR_ATTR_FAN(12),
1795        SENSOR_ATTR_FAN(13),
1796        SENSOR_ATTR_FAN(14),
1797};
1798
1799static const struct sensor_device_attribute_2 w83795_temp[][28] = {
1800        SENSOR_ATTR_TEMP(1),
1801        SENSOR_ATTR_TEMP(2),
1802        SENSOR_ATTR_TEMP(3),
1803        SENSOR_ATTR_TEMP(4),
1804        SENSOR_ATTR_TEMP(5),
1805        SENSOR_ATTR_TEMP(6),
1806};
1807
1808static const struct sensor_device_attribute_2 w83795_dts[][8] = {
1809        SENSOR_ATTR_DTS(7),
1810        SENSOR_ATTR_DTS(8),
1811        SENSOR_ATTR_DTS(9),
1812        SENSOR_ATTR_DTS(10),
1813        SENSOR_ATTR_DTS(11),
1814        SENSOR_ATTR_DTS(12),
1815        SENSOR_ATTR_DTS(13),
1816        SENSOR_ATTR_DTS(14),
1817};
1818
1819static const struct sensor_device_attribute_2 w83795_pwm[][8] = {
1820        SENSOR_ATTR_PWM(1),
1821        SENSOR_ATTR_PWM(2),
1822        SENSOR_ATTR_PWM(3),
1823        SENSOR_ATTR_PWM(4),
1824        SENSOR_ATTR_PWM(5),
1825        SENSOR_ATTR_PWM(6),
1826        SENSOR_ATTR_PWM(7),
1827        SENSOR_ATTR_PWM(8),
1828};
1829
1830static const struct sensor_device_attribute_2 w83795_tss[6] = {
1831        SENSOR_ATTR_2(temp1_source_sel, S_IWUSR | S_IRUGO,
1832                      show_temp_src, store_temp_src, NOT_USED, 0),
1833        SENSOR_ATTR_2(temp2_source_sel, S_IWUSR | S_IRUGO,
1834                      show_temp_src, store_temp_src, NOT_USED, 1),
1835        SENSOR_ATTR_2(temp3_source_sel, S_IWUSR | S_IRUGO,
1836                      show_temp_src, store_temp_src, NOT_USED, 2),
1837        SENSOR_ATTR_2(temp4_source_sel, S_IWUSR | S_IRUGO,
1838                      show_temp_src, store_temp_src, NOT_USED, 3),
1839        SENSOR_ATTR_2(temp5_source_sel, S_IWUSR | S_IRUGO,
1840                      show_temp_src, store_temp_src, NOT_USED, 4),
1841        SENSOR_ATTR_2(temp6_source_sel, S_IWUSR | S_IRUGO,
1842                      show_temp_src, store_temp_src, NOT_USED, 5),
1843};
1844
1845static const struct sensor_device_attribute_2 sda_single_files[] = {
1846        SENSOR_ATTR_2(intrusion0_alarm, S_IWUSR | S_IRUGO, show_alarm_beep,
1847                      store_chassis_clear, ALARM_STATUS, 46),
1848#ifdef CONFIG_SENSORS_W83795_FANCTRL
1849        SENSOR_ATTR_2(speed_cruise_tolerance, S_IWUSR | S_IRUGO, show_fanin,
1850                store_fanin, FANIN_TOL, NOT_USED),
1851        SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup,
1852                      store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED),
1853        SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup,
1854                      store_sf_setup, SETUP_PWM_UPTIME, NOT_USED),
1855        SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup,
1856                      store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED),
1857#endif
1858};
1859
1860static const struct sensor_device_attribute_2 sda_beep_files[] = {
1861        SENSOR_ATTR_2(intrusion0_beep, S_IWUSR | S_IRUGO, show_alarm_beep,
1862                      store_beep, BEEP_ENABLE, 46),
1863        SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_alarm_beep,
1864                      store_beep, BEEP_ENABLE, 47),
1865};
1866
1867/*
1868 * Driver interface
1869 */
1870
1871static void w83795_init_client(struct i2c_client *client)
1872{
1873        struct w83795_data *data = i2c_get_clientdata(client);
1874        static const u16 clkin[4] = {   /* in kHz */
1875                14318, 24000, 33333, 48000
1876        };
1877        u8 config;
1878
1879        if (reset)
1880                w83795_write(client, W83795_REG_CONFIG, 0x80);
1881
1882        /* Start monitoring if needed */
1883        config = w83795_read(client, W83795_REG_CONFIG);
1884        if (!(config & W83795_REG_CONFIG_START)) {
1885                dev_info(&client->dev, "Enabling monitoring operations\n");
1886                w83795_write(client, W83795_REG_CONFIG,
1887                             config | W83795_REG_CONFIG_START);
1888        }
1889
1890        data->clkin = clkin[(config >> 3) & 0x3];
1891        dev_dbg(&client->dev, "clkin = %u kHz\n", data->clkin);
1892}
1893
1894static int w83795_get_device_id(struct i2c_client *client)
1895{
1896        int device_id;
1897
1898        device_id = i2c_smbus_read_byte_data(client, W83795_REG_DEVICEID);
1899
1900        /*
1901         * Special case for rev. A chips; can't be checked first because later
1902         * revisions emulate this for compatibility
1903         */
1904        if (device_id < 0 || (device_id & 0xf0) != 0x50) {
1905                int alt_id;
1906
1907                alt_id = i2c_smbus_read_byte_data(client,
1908                                                  W83795_REG_DEVICEID_A);
1909                if (alt_id == 0x50)
1910                        device_id = alt_id;
1911        }
1912
1913        return device_id;
1914}
1915
1916/* Return 0 if detection is successful, -ENODEV otherwise */
1917static int w83795_detect(struct i2c_client *client,
1918                         struct i2c_board_info *info)
1919{
1920        int bank, vendor_id, device_id, expected, i2c_addr, config;
1921        struct i2c_adapter *adapter = client->adapter;
1922        unsigned short address = client->addr;
1923        const char *chip_name;
1924
1925        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
1926                return -ENODEV;
1927        bank = i2c_smbus_read_byte_data(client, W83795_REG_BANKSEL);
1928        if (bank < 0 || (bank & 0x7c)) {
1929                dev_dbg(&adapter->dev,
1930                        "w83795: Detection failed at addr 0x%02hx, check %s\n",
1931                        address, "bank");
1932                return -ENODEV;
1933        }
1934
1935        /* Check Nuvoton vendor ID */
1936        vendor_id = i2c_smbus_read_byte_data(client, W83795_REG_VENDORID);
1937        expected = bank & 0x80 ? 0x5c : 0xa3;
1938        if (vendor_id != expected) {
1939                dev_dbg(&adapter->dev,
1940                        "w83795: Detection failed at addr 0x%02hx, check %s\n",
1941                        address, "vendor id");
1942                return -ENODEV;
1943        }
1944
1945        /* Check device ID */
1946        device_id = w83795_get_device_id(client) |
1947                    (i2c_smbus_read_byte_data(client, W83795_REG_CHIPID) << 8);
1948        if ((device_id >> 4) != 0x795) {
1949                dev_dbg(&adapter->dev,
1950                        "w83795: Detection failed at addr 0x%02hx, check %s\n",
1951                        address, "device id\n");
1952                return -ENODEV;
1953        }
1954
1955        /*
1956         * If Nuvoton chip, address of chip and W83795_REG_I2C_ADDR
1957         * should match
1958         */
1959        if ((bank & 0x07) == 0) {
1960                i2c_addr = i2c_smbus_read_byte_data(client,
1961                                                    W83795_REG_I2C_ADDR);
1962                if ((i2c_addr & 0x7f) != address) {
1963                        dev_dbg(&adapter->dev,
1964                                "w83795: Detection failed at addr 0x%02hx, "
1965                                "check %s\n", address, "i2c addr");
1966                        return -ENODEV;
1967                }
1968        }
1969
1970        /*
1971         * Check 795 chip type: 795G or 795ADG
1972         * Usually we don't write to chips during detection, but here we don't
1973         * quite have the choice; hopefully it's OK, we are about to return
1974         * success anyway
1975         */
1976        if ((bank & 0x07) != 0)
1977                i2c_smbus_write_byte_data(client, W83795_REG_BANKSEL,
1978                                          bank & ~0x07);
1979        config = i2c_smbus_read_byte_data(client, W83795_REG_CONFIG);
1980        if (config & W83795_REG_CONFIG_CONFIG48)
1981                chip_name = "w83795adg";
1982        else
1983                chip_name = "w83795g";
1984
1985        strlcpy(info->type, chip_name, I2C_NAME_SIZE);
1986        dev_info(&adapter->dev, "Found %s rev. %c at 0x%02hx\n", chip_name,
1987                 'A' + (device_id & 0xf), address);
1988
1989        return 0;
1990}
1991
1992#ifdef CONFIG_SENSORS_W83795_FANCTRL
1993#define NUM_PWM_ATTRIBUTES      ARRAY_SIZE(w83795_pwm[0])
1994#define NUM_TEMP_ATTRIBUTES     ARRAY_SIZE(w83795_temp[0])
1995#else
1996#define NUM_PWM_ATTRIBUTES      4
1997#define NUM_TEMP_ATTRIBUTES     8
1998#endif
1999
2000static int w83795_handle_files(struct device *dev, int (*fn)(struct device *,
2001                               const struct device_attribute *))
2002{
2003        struct w83795_data *data = dev_get_drvdata(dev);
2004        int err, i, j;
2005
2006        for (i = 0; i < ARRAY_SIZE(w83795_in); i++) {
2007                if (!(data->has_in & (1 << i)))
2008                        continue;
2009                for (j = 0; j < ARRAY_SIZE(w83795_in[0]); j++) {
2010                        if (j == 4 && !data->enable_beep)
2011                                continue;
2012                        err = fn(dev, &w83795_in[i][j].dev_attr);
2013                        if (err)
2014                                return err;
2015                }
2016        }
2017
2018        for (i = 0; i < ARRAY_SIZE(w83795_fan); i++) {
2019                if (!(data->has_fan & (1 << i)))
2020                        continue;
2021                for (j = 0; j < ARRAY_SIZE(w83795_fan[0]); j++) {
2022                        if (j == 3 && !data->enable_beep)
2023                                continue;
2024                        err = fn(dev, &w83795_fan[i][j].dev_attr);
2025                        if (err)
2026                                return err;
2027                }
2028        }
2029
2030        for (i = 0; i < ARRAY_SIZE(w83795_tss); i++) {
2031                j = w83795_tss_useful(data, i);
2032                if (!j)
2033                        continue;
2034                err = fn(dev, &w83795_tss[i].dev_attr);
2035                if (err)
2036                        return err;
2037        }
2038
2039        for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) {
2040                err = fn(dev, &sda_single_files[i].dev_attr);
2041                if (err)
2042                        return err;
2043        }
2044
2045        if (data->enable_beep) {
2046                for (i = 0; i < ARRAY_SIZE(sda_beep_files); i++) {
2047                        err = fn(dev, &sda_beep_files[i].dev_attr);
2048                        if (err)
2049                                return err;
2050                }
2051        }
2052
2053        for (i = 0; i < data->has_pwm; i++) {
2054                for (j = 0; j < NUM_PWM_ATTRIBUTES; j++) {
2055                        err = fn(dev, &w83795_pwm[i][j].dev_attr);
2056                        if (err)
2057                                return err;
2058                }
2059        }
2060
2061        for (i = 0; i < ARRAY_SIZE(w83795_temp); i++) {
2062                if (!(data->has_temp & (1 << i)))
2063                        continue;
2064                for (j = 0; j < NUM_TEMP_ATTRIBUTES; j++) {
2065                        if (j == 7 && !data->enable_beep)
2066                                continue;
2067                        err = fn(dev, &w83795_temp[i][j].dev_attr);
2068                        if (err)
2069                                return err;
2070                }
2071        }
2072
2073        if (data->enable_dts) {
2074                for (i = 0; i < ARRAY_SIZE(w83795_dts); i++) {
2075                        if (!(data->has_dts & (1 << i)))
2076                                continue;
2077                        for (j = 0; j < ARRAY_SIZE(w83795_dts[0]); j++) {
2078                                if (j == 7 && !data->enable_beep)
2079                                        continue;
2080                                err = fn(dev, &w83795_dts[i][j].dev_attr);
2081                                if (err)
2082                                        return err;
2083                        }
2084                }
2085        }
2086
2087        return 0;
2088}
2089
2090/* We need a wrapper that fits in w83795_handle_files */
2091static int device_remove_file_wrapper(struct device *dev,
2092                                      const struct device_attribute *attr)
2093{
2094        device_remove_file(dev, attr);
2095        return 0;
2096}
2097
2098static void w83795_check_dynamic_in_limits(struct i2c_client *client)
2099{
2100        struct w83795_data *data = i2c_get_clientdata(client);
2101        u8 vid_ctl;
2102        int i, err_max, err_min;
2103
2104        vid_ctl = w83795_read(client, W83795_REG_VID_CTRL);
2105
2106        /* Return immediately if VRM isn't configured */
2107        if ((vid_ctl & 0x07) == 0x00 || (vid_ctl & 0x07) == 0x07)
2108                return;
2109
2110        data->has_dyn_in = (vid_ctl >> 3) & 0x07;
2111        for (i = 0; i < 2; i++) {
2112                if (!(data->has_dyn_in & (1 << i)))
2113                        continue;
2114
2115                /* Voltage limits in dynamic mode, switch to read-only */
2116                err_max = sysfs_chmod_file(&client->dev.kobj,
2117                                           &w83795_in[i][2].dev_attr.attr,
2118                                           S_IRUGO);
2119                err_min = sysfs_chmod_file(&client->dev.kobj,
2120                                           &w83795_in[i][3].dev_attr.attr,
2121                                           S_IRUGO);
2122                if (err_max || err_min)
2123                        dev_warn(&client->dev,
2124                                 "Failed to set in%d limits read-only (%d, %d)\n",
2125                                 i, err_max, err_min);
2126                else
2127                        dev_info(&client->dev,
2128                                 "in%d limits set dynamically from VID\n", i);
2129        }
2130}
2131
2132/* Check pins that can be used for either temperature or voltage monitoring */
2133static void w83795_apply_temp_config(struct w83795_data *data, u8 config,
2134                                     int temp_chan, int in_chan)
2135{
2136        /* config is a 2-bit value */
2137        switch (config) {
2138        case 0x2: /* Voltage monitoring */
2139                data->has_in |= 1 << in_chan;
2140                break;
2141        case 0x1: /* Thermal diode */
2142                if (temp_chan >= 4)
2143                        break;
2144                data->temp_mode |= 1 << temp_chan;
2145                /* fall through */
2146        case 0x3: /* Thermistor */
2147                data->has_temp |= 1 << temp_chan;
2148                break;
2149        }
2150}
2151
2152static int w83795_probe(struct i2c_client *client,
2153                        const struct i2c_device_id *id)
2154{
2155        int i;
2156        u8 tmp;
2157        struct device *dev = &client->dev;
2158        struct w83795_data *data;
2159        int err;
2160
2161        data = devm_kzalloc(dev, sizeof(struct w83795_data), GFP_KERNEL);
2162        if (!data)
2163                return -ENOMEM;
2164
2165        i2c_set_clientdata(client, data);
2166        data->chip_type = id->driver_data;
2167        data->bank = i2c_smbus_read_byte_data(client, W83795_REG_BANKSEL);
2168        mutex_init(&data->update_lock);
2169
2170        /* Initialize the chip */
2171        w83795_init_client(client);
2172
2173        /* Check which voltages and fans are present */
2174        data->has_in = w83795_read(client, W83795_REG_VOLT_CTRL1)
2175                     | (w83795_read(client, W83795_REG_VOLT_CTRL2) << 8);
2176        data->has_fan = w83795_read(client, W83795_REG_FANIN_CTRL1)
2177                      | (w83795_read(client, W83795_REG_FANIN_CTRL2) << 8);
2178
2179        /* Check which analog temperatures and extra voltages are present */
2180        tmp = w83795_read(client, W83795_REG_TEMP_CTRL1);
2181        if (tmp & 0x20)
2182                data->enable_dts = 1;
2183        w83795_apply_temp_config(data, (tmp >> 2) & 0x3, 5, 16);
2184        w83795_apply_temp_config(data, tmp & 0x3, 4, 15);
2185        tmp = w83795_read(client, W83795_REG_TEMP_CTRL2);
2186        w83795_apply_temp_config(data, tmp >> 6, 3, 20);
2187        w83795_apply_temp_config(data, (tmp >> 4) & 0x3, 2, 19);
2188        w83795_apply_temp_config(data, (tmp >> 2) & 0x3, 1, 18);
2189        w83795_apply_temp_config(data, tmp & 0x3, 0, 17);
2190
2191        /* Check DTS enable status */
2192        if (data->enable_dts) {
2193                if (1 & w83795_read(client, W83795_REG_DTSC))
2194                        data->enable_dts |= 2;
2195                data->has_dts = w83795_read(client, W83795_REG_DTSE);
2196        }
2197
2198        /* Report PECI Tbase values */
2199        if (data->enable_dts == 1) {
2200                for (i = 0; i < 8; i++) {
2201                        if (!(data->has_dts & (1 << i)))
2202                                continue;
2203                        tmp = w83795_read(client, W83795_REG_PECI_TBASE(i));
2204                        dev_info(&client->dev,
2205                                 "PECI agent %d Tbase temperature: %u\n",
2206                                 i + 1, (unsigned int)tmp & 0x7f);
2207                }
2208        }
2209
2210        data->has_gain = w83795_read(client, W83795_REG_VMIGB_CTRL) & 0x0f;
2211
2212        /* pwm and smart fan */
2213        if (data->chip_type == w83795g)
2214                data->has_pwm = 8;
2215        else
2216                data->has_pwm = 2;
2217
2218        /* Check if BEEP pin is available */
2219        if (data->chip_type == w83795g) {
2220                /* The W83795G has a dedicated BEEP pin */
2221                data->enable_beep = 1;
2222        } else {
2223                /*
2224                 * The W83795ADG has a shared pin for OVT# and BEEP, so you
2225                 * can't have both
2226                 */
2227                tmp = w83795_read(client, W83795_REG_OVT_CFG);
2228                if ((tmp & OVT_CFG_SEL) == 0)
2229                        data->enable_beep = 1;
2230        }
2231
2232        err = w83795_handle_files(dev, device_create_file);
2233        if (err)
2234                goto exit_remove;
2235
2236        if (data->chip_type == w83795g)
2237                w83795_check_dynamic_in_limits(client);
2238
2239        data->hwmon_dev = hwmon_device_register(dev);
2240        if (IS_ERR(data->hwmon_dev)) {
2241                err = PTR_ERR(data->hwmon_dev);
2242                goto exit_remove;
2243        }
2244
2245        return 0;
2246
2247exit_remove:
2248        w83795_handle_files(dev, device_remove_file_wrapper);
2249        return err;
2250}
2251
2252static int w83795_remove(struct i2c_client *client)
2253{
2254        struct w83795_data *data = i2c_get_clientdata(client);
2255
2256        hwmon_device_unregister(data->hwmon_dev);
2257        w83795_handle_files(&client->dev, device_remove_file_wrapper);
2258
2259        return 0;
2260}
2261
2262
2263static const struct i2c_device_id w83795_id[] = {
2264        { "w83795g", w83795g },
2265        { "w83795adg", w83795adg },
2266        { }
2267};
2268MODULE_DEVICE_TABLE(i2c, w83795_id);
2269
2270static struct i2c_driver w83795_driver = {
2271        .driver = {
2272                   .name = "w83795",
2273        },
2274        .probe          = w83795_probe,
2275        .remove         = w83795_remove,
2276        .id_table       = w83795_id,
2277
2278        .class          = I2C_CLASS_HWMON,
2279        .detect         = w83795_detect,
2280        .address_list   = normal_i2c,
2281};
2282
2283module_i2c_driver(w83795_driver);
2284
2285MODULE_AUTHOR("Wei Song, Jean Delvare <jdelvare@suse.de>");
2286MODULE_DESCRIPTION("W83795G/ADG hardware monitoring driver");
2287MODULE_LICENSE("GPL");
2288