/* Intel Ethernet Switch Host Interface Driver
 * Copyright(c) 2013 - 2014 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms and conditions of the GNU General Public License,
 * version 2, as published by the Free Software Foundation.
 *
 * This program is distributed in the hope it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * The full GNU General Public License is included in this distribution in
 * the file called "COPYING".
 *
 * Contact Information:
 * e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
 */

#include "fm10k_pf.h"
#include "fm10k_vf.h"

/**
 *  fm10k_reset_hw_pf - PF hardware reset
 *  @hw: pointer to hardware structure
 *
 *  This function should return the hardware to a state similar to the
 *  one it is in after being powered on.
 **/
static s32 fm10k_reset_hw_pf(struct fm10k_hw *hw)
{
        s32 err;
        u32 reg;
        u16 i;

        /* Disable interrupts */
        fm10k_write_reg(hw, FM10K_EIMR, FM10K_EIMR_DISABLE(ALL));

        /* Lock ITR2 reg 0 into itself and disable interrupt moderation */
        fm10k_write_reg(hw, FM10K_ITR2(0), 0);
        fm10k_write_reg(hw, FM10K_INT_CTRL, 0);

        /* We assume here Tx and Rx queue 0 are owned by the PF */

        /* Shut off VF access to their queues forcing them to queue 0 */
        for (i = 0; i < FM10K_TQMAP_TABLE_SIZE; i++) {
                fm10k_write_reg(hw, FM10K_TQMAP(i), 0);
                fm10k_write_reg(hw, FM10K_RQMAP(i), 0);
        }

        /* shut down all rings */
        err = fm10k_disable_queues_generic(hw, FM10K_MAX_QUEUES);
        if (err)
                return err;

        /* Verify that DMA is no longer active */
        reg = fm10k_read_reg(hw, FM10K_DMA_CTRL);
        if (reg & (FM10K_DMA_CTRL_TX_ACTIVE | FM10K_DMA_CTRL_RX_ACTIVE))
                return FM10K_ERR_DMA_PENDING;

        /* Inititate data path reset */
        reg |= FM10K_DMA_CTRL_DATAPATH_RESET;
        fm10k_write_reg(hw, FM10K_DMA_CTRL, reg);

        /* Flush write and allow 100us for reset to complete */
        fm10k_write_flush(hw);
        udelay(FM10K_RESET_TIMEOUT);

        /* Verify we made it out of reset */
        reg = fm10k_read_reg(hw, FM10K_IP);
        if (!(reg & FM10K_IP_NOTINRESET))
                err = FM10K_ERR_RESET_FAILED;

        return err;
}

/**
 *  fm10k_is_ari_hierarchy_pf - Indicate ARI hierarchy support
 *  @hw: pointer to hardware structure
 *
 *  Looks at the ARI hierarchy bit to determine whether ARI is supported or not.
 **/
static bool fm10k_is_ari_hierarchy_pf(struct fm10k_hw *hw)
{
        u16 sriov_ctrl = fm10k_read_pci_cfg_word(hw, FM10K_PCIE_SRIOV_CTRL);

        return !!(sriov_ctrl & FM10K_PCIE_SRIOV_CTRL_VFARI);
}

/**
 *  fm10k_init_hw_pf - PF hardware initialization
 *  @hw: pointer to hardware structure
 *
 **/
static s32 fm10k_init_hw_pf(struct fm10k_hw *hw)
{
        u32 dma_ctrl, txqctl;
        u16 i;

        /* Establish default VSI as valid */
        fm10k_write_reg(hw, FM10K_DGLORTDEC(fm10k_dglort_default), 0);
        fm10k_write_reg(hw, FM10K_DGLORTMAP(fm10k_dglort_default),
                        FM10K_DGLORTMAP_ANY);

        /* Invalidate all other GLORT entries */
        for (i = 1; i < FM10K_DGLORT_COUNT; i++)
                fm10k_write_reg(hw, FM10K_DGLORTMAP(i), FM10K_DGLORTMAP_NONE);

        /* reset ITR2(0) to point to itself */
        fm10k_write_reg(hw, FM10K_ITR2(0), 0);

        /* reset VF ITR2(0) to point to 0 avoid PF registers */
        fm10k_write_reg(hw, FM10K_ITR2(FM10K_ITR_REG_COUNT_PF), 0);

        /* loop through all PF ITR2 registers pointing them to the previous */
        for (i = 1; i < FM10K_ITR_REG_COUNT_PF; i++)
                fm10k_write_reg(hw, FM10K_ITR2(i), i - 1);

        /* Enable interrupt moderator if not already enabled */
        fm10k_write_reg(hw, FM10K_INT_CTRL, FM10K_INT_CTRL_ENABLEMODERATOR);

        /* compute the default txqctl configuration */
        txqctl = FM10K_TXQCTL_PF | FM10K_TXQCTL_UNLIMITED_BW |
                 (hw->mac.default_vid << FM10K_TXQCTL_VID_SHIFT);

        for (i = 0; i < FM10K_MAX_QUEUES; i++) {
                /* configure rings for 256 Queue / 32 Descriptor cache mode */
                fm10k_write_reg(hw, FM10K_TQDLOC(i),
                                (i * FM10K_TQDLOC_BASE_32_DESC) |
                                FM10K_TQDLOC_SIZE_32_DESC);
                fm10k_write_reg(hw, FM10K_TXQCTL(i), txqctl);

                /* configure rings to provide TPH processing hints */
                fm10k_write_reg(hw, FM10K_TPH_TXCTRL(i),
                                FM10K_TPH_TXCTRL_DESC_TPHEN |
                                FM10K_TPH_TXCTRL_DESC_RROEN |
                                FM10K_TPH_TXCTRL_DESC_WROEN |
                                FM10K_TPH_TXCTRL_DATA_RROEN);
                fm10k_write_reg(hw, FM10K_TPH_RXCTRL(i),
                                FM10K_TPH_RXCTRL_DESC_TPHEN |
                                FM10K_TPH_RXCTRL_DESC_RROEN |
                                FM10K_TPH_RXCTRL_DATA_WROEN |
                                FM10K_TPH_RXCTRL_HDR_WROEN);
        }

        /* set max hold interval to align with 1.024 usec in all modes */
        switch (hw->bus.speed) {
        case fm10k_bus_speed_2500:
                dma_ctrl = FM10K_DMA_CTRL_MAX_HOLD_1US_GEN1;
                break;
        case fm10k_bus_speed_5000:
                dma_ctrl = FM10K_DMA_CTRL_MAX_HOLD_1US_GEN2;
                break;
        case fm10k_bus_speed_8000:
                dma_ctrl = FM10K_DMA_CTRL_MAX_HOLD_1US_GEN3;
                break;
        default:
                dma_ctrl = 0;
                break;
        }

        /* Configure TSO flags */
        fm10k_write_reg(hw, FM10K_DTXTCPFLGL, FM10K_TSO_FLAGS_LOW);
        fm10k_write_reg(hw, FM10K_DTXTCPFLGH, FM10K_TSO_FLAGS_HI);

        /* Enable DMA engine
         * Set Rx Descriptor size to 32
         * Set Minimum MSS to 64
         * Set Maximum number of Rx queues to 256 / 32 Descriptor
         */
        dma_ctrl |= FM10K_DMA_CTRL_TX_ENABLE | FM10K_DMA_CTRL_RX_ENABLE |
                    FM10K_DMA_CTRL_RX_DESC_SIZE | FM10K_DMA_CTRL_MINMSS_64 |
                    FM10K_DMA_CTRL_32_DESC;

        fm10k_write_reg(hw, FM10K_DMA_CTRL, dma_ctrl);

        /* record maximum queue count, we limit ourselves to 128 */
        hw->mac.max_queues = FM10K_MAX_QUEUES_PF;

        /* We support either 64 VFs or 7 VFs depending on if we have ARI */
        hw->iov.total_vfs = fm10k_is_ari_hierarchy_pf(hw) ? 64 : 7;

        return 0;
}

/**
 *  fm10k_is_slot_appropriate_pf - Indicate appropriate slot for this SKU
 *  @hw: pointer to hardware structure
 *
 *  Looks at the PCIe bus info to confirm whether or not this slot can support
 *  the necessary bandwidth for this device.
 **/
static bool fm10k_is_slot_appropriate_pf(struct fm10k_hw *hw)
{
        return (hw->bus.speed == hw->bus_caps.speed) &&
               (hw->bus.width == hw->bus_caps.width);
}

/**
 *  fm10k_update_vlan_pf - Update status of VLAN ID in VLAN filter table
 *  @hw: pointer to hardware structure
 *  @vid: VLAN ID to add to table
 *  @vsi: Index indicating VF ID or PF ID in table
 *  @set: Indicates if this is a set or clear operation
 *
 *  This function adds or removes the corresponding VLAN ID from the VLAN
 *  filter table for the corresponding function.  In addition to the
 *  standard set/clear that supports one bit a multi-bit write is
 *  supported to set 64 bits at a time.
 **/
static s32 fm10k_update_vlan_pf(struct fm10k_hw *hw, u32 vid, u8 vsi, bool set)
{
        u32 vlan_table, reg, mask, bit, len;

        /* verify the VSI index is valid */
        if (vsi > FM10K_VLAN_TABLE_VSI_MAX)
                return FM10K_ERR_PARAM;

        /* VLAN multi-bit write:
         * The multi-bit write has several parts to it.
         *    3                   2                   1                   0
         *  1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
         * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
         * | RSVD0 |         Length        |C|RSVD0|        VLAN ID        |
         * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
         *
         * VLAN ID: Vlan Starting value
         * RSVD0: Reserved section, must be 0
         * C: Flag field, 0 is set, 1 is clear (Used in VF VLAN message)
         * Length: Number of times to repeat the bit being set
         */
        len = vid >> 16;
        vid = (vid << 17) >> 17;

        /* verify the reserved 0 fields are 0 */
        if (len >= FM10K_VLAN_TABLE_VID_MAX ||
            vid >= FM10K_VLAN_TABLE_VID_MAX)
                return FM10K_ERR_PARAM;

        /* Loop through the table updating all required VLANs */
        for (reg = FM10K_VLAN_TABLE(vsi, vid / 32), bit = vid % 32;
             len < FM10K_VLAN_TABLE_VID_MAX;
             len -= 32 - bit, reg++, bit = 0) {
                /* record the initial state of the register */
                vlan_table = fm10k_read_reg(hw, reg);

                /* truncate mask if we are at the start or end of the run */
                mask = (~(u32)0 >> ((len < 31) ? 31 - len : 0)) << bit;

                /* make necessary modifications to the register */
                mask &= set ? ~vlan_table : vlan_table;
                if (mask)
                        fm10k_write_reg(hw, reg, vlan_table ^ mask);
        }

        return 0;
}

/**
 *  fm10k_read_mac_addr_pf - Read device MAC address
 *  @hw: pointer to the HW structure
 *
 *  Reads the device MAC address from the SM_AREA and stores the value.
 **/
static s32 fm10k_read_mac_addr_pf(struct fm10k_hw *hw)
{
        u8 perm_addr[ETH_ALEN];
        u32 serial_num;
        int i;

        serial_num = fm10k_read_reg(hw, FM10K_SM_AREA(1));

        /* last byte should be all 1's */
        if ((~serial_num) << 24)
                return  FM10K_ERR_INVALID_MAC_ADDR;

        perm_addr[0] = (u8)(serial_num >> 24);
        perm_addr[1] = (u8)(serial_num >> 16);
        perm_addr[2] = (u8)(serial_num >> 8);

        serial_num = fm10k_read_reg(hw, FM10K_SM_AREA(0));

        /* first byte should be all 1's */
        if ((~serial_num) >> 24)
                return  FM10K_ERR_INVALID_MAC_ADDR;

        perm_addr[3] = (u8)(serial_num >> 16);
        perm_addr[4] = (u8)(serial_num >> 8);
        perm_addr[5] = (u8)(serial_num);

        for (i = 0; i < ETH_ALEN; i++) {
                hw->mac.perm_addr[i] = perm_addr[i];
                hw->mac.addr[i] = perm_addr[i];
        }

        return 0;
}

/**
 *  fm10k_glort_valid_pf - Validate that the provided glort is valid
 *  @hw: pointer to the HW structure
 *  @glort: base glort to be validated
 *
 *  This function will return an error if the provided glort is invalid
 **/
bool fm10k_glort_valid_pf(struct fm10k_hw *hw, u16 glort)
{
        glort &= hw->mac.dglort_map >> FM10K_DGLORTMAP_MASK_SHIFT;

        return glort == (hw->mac.dglort_map & FM10K_DGLORTMAP_NONE);
}

/**
 *  fm10k_update_uc_addr_pf - Update device unicast addresss
 *  @hw: pointer to the HW structure
 *  @glort: base resource tag for this request
 *  @mac: MAC address to add/remove from table
 *  @vid: VLAN ID to add/remove from table
 *  @add: Indicates if this is an add or remove operation
 *  @flags: flags field to indicate add and secure
 *
 *  This function generates a message to the Switch API requesting
 *  that the given logical port add/remove the given L2 MAC/VLAN address.
 **/
static s32 fm10k_update_xc_addr_pf(struct fm10k_hw *hw, u16 glort,
                                   const u8 *mac, u16 vid, bool add, u8 flags)
{
        struct fm10k_mbx_info *mbx = &hw->mbx;
        struct fm10k_mac_update mac_update;
        u32 msg[5];

        /* if glort is not valid return error */
        if (!fm10k_glort_valid_pf(hw, glort))
                return FM10K_ERR_PARAM;

        /* drop upper 4 bits of VLAN ID */
        vid = (vid << 4) >> 4;

        /* record fields */
        mac_update.mac_lower = cpu_to_le32(((u32)mac[2] << 24) |
                                                 ((u32)mac[3] << 16) |
                                                 ((u32)mac[4] << 8) |
                                                 ((u32)mac[5]));
        mac_update.mac_upper = cpu_to_le16(((u32)mac[0] << 8) |
                                                 ((u32)mac[1]));
        mac_update.vlan = cpu_to_le16(vid);
        mac_update.glort = cpu_to_le16(glort);
        mac_update.action = add ? 0 : 1;
        mac_update.flags = flags;

        /* populate mac_update fields */
        fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_UPDATE_MAC_FWD_RULE);
        fm10k_tlv_attr_put_le_struct(msg, FM10K_PF_ATTR_ID_MAC_UPDATE,
                                     &mac_update, sizeof(mac_update));

        /* load onto outgoing mailbox */
        return mbx->ops.enqueue_tx(hw, mbx, msg);
}

/**
 *  fm10k_update_uc_addr_pf - Update device unicast addresss
 *  @hw: pointer to the HW structure
 *  @glort: base resource tag for this request
 *  @mac: MAC address to add/remove from table
 *  @vid: VLAN ID to add/remove from table
 *  @add: Indicates if this is an add or remove operation
 *  @flags: flags field to indicate add and secure
 *
 *  This function is used to add or remove unicast addresses for
 *  the PF.
 **/
static s32 fm10k_update_uc_addr_pf(struct fm10k_hw *hw, u16 glort,
                                   const u8 *mac, u16 vid, bool add, u8 flags)
{
        /* verify MAC address is valid */
        if (!is_valid_ether_addr(mac))
                return FM10K_ERR_PARAM;

        return fm10k_update_xc_addr_pf(hw, glort, mac, vid, add, flags);
}

/**
 *  fm10k_update_mc_addr_pf - Update device multicast addresses
 *  @hw: pointer to the HW structure
 *  @glort: base resource tag for this request
 *  @mac: MAC address to add/remove from table
 *  @vid: VLAN ID to add/remove from table
 *  @add: Indicates if this is an add or remove operation
 *
 *  This function is used to add or remove multicast MAC addresses for
 *  the PF.
 **/
static s32 fm10k_update_mc_addr_pf(struct fm10k_hw *hw, u16 glort,
                                   const u8 *mac, u16 vid, bool add)
{
        /* verify multicast address is valid */
        if (!is_multicast_ether_addr(mac))
                return FM10K_ERR_PARAM;

        return fm10k_update_xc_addr_pf(hw, glort, mac, vid, add, 0);
}

/**
 *  fm10k_update_xcast_mode_pf - Request update of multicast mode
 *  @hw: pointer to hardware structure
 *  @glort: base resource tag for this request
 *  @mode: integer value indicating mode being requested
 *
 *  This function will attempt to request a higher mode for the port
 *  so that it can enable either multicast, multicast promiscuous, or
 *  promiscuous mode of operation.
 **/
static s32 fm10k_update_xcast_mode_pf(struct fm10k_hw *hw, u16 glort, u8 mode)
{
        struct fm10k_mbx_info *mbx = &hw->mbx;
        u32 msg[3], xcast_mode;

        if (mode > FM10K_XCAST_MODE_NONE)
                return FM10K_ERR_PARAM;
        /* if glort is not valid return error */
        if (!fm10k_glort_valid_pf(hw, glort))
                return FM10K_ERR_PARAM;

        /* write xcast mode as a single u32 value,
         * lower 16 bits: glort
         * upper 16 bits: mode
         */
        xcast_mode = ((u32)mode << 16) | glort;

        /* generate message requesting to change xcast mode */
        fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_XCAST_MODES);
        fm10k_tlv_attr_put_u32(msg, FM10K_PF_ATTR_ID_XCAST_MODE, xcast_mode);

        /* load onto outgoing mailbox */
        return mbx->ops.enqueue_tx(hw, mbx, msg);
}

/**
 *  fm10k_update_int_moderator_pf - Update interrupt moderator linked list
 *  @hw: pointer to hardware structure
 *
 *  This function walks through the MSI-X vector table to determine the
 *  number of active interrupts and based on that information updates the
 *  interrupt moderator linked list.
 **/
static void fm10k_update_int_moderator_pf(struct fm10k_hw *hw)
{
        u32 i;

        /* Disable interrupt moderator */
        fm10k_write_reg(hw, FM10K_INT_CTRL, 0);

        /* loop through PF from last to first looking enabled vectors */
        for (i = FM10K_ITR_REG_COUNT_PF - 1; i; i--) {
                if (!fm10k_read_reg(hw, FM10K_MSIX_VECTOR_MASK(i)))
                        break;
        }

        /* always reset VFITR2[0] to point to last enabled PF vector*/
        fm10k_write_reg(hw, FM10K_ITR2(FM10K_ITR_REG_COUNT_PF), i);

        /* reset ITR2[0] to point to last enabled PF vector */
        if (!hw->iov.num_vfs)
                fm10k_write_reg(hw, FM10K_ITR2(0), i);

        /* Enable interrupt moderator */
        fm10k_write_reg(hw, FM10K_INT_CTRL, FM10K_INT_CTRL_ENABLEMODERATOR);
}

/**
 *  fm10k_update_lport_state_pf - Notify the switch of a change in port state
 *  @hw: pointer to the HW structure
 *  @glort: base resource tag for this request
 *  @count: number of logical ports being updated
 *  @enable: boolean value indicating enable or disable
 *
 *  This function is used to add/remove a logical port from the switch.
 **/
static s32 fm10k_update_lport_state_pf(struct fm10k_hw *hw, u16 glort,
                                       u16 count, bool enable)
{
        struct fm10k_mbx_info *mbx = &hw->mbx;
        u32 msg[3], lport_msg;

        /* do nothing if we are being asked to create or destroy 0 ports */
        if (!count)
                return 0;

        /* if glort is not valid return error */
        if (!fm10k_glort_valid_pf(hw, glort))
                return FM10K_ERR_PARAM;

        /* construct the lport message from the 2 pieces of data we have */
        lport_msg = ((u32)count << 16) | glort;

        /* generate lport create/delete message */
        fm10k_tlv_msg_init(msg, enable ? FM10K_PF_MSG_ID_LPORT_CREATE :
                                         FM10K_PF_MSG_ID_LPORT_DELETE);
        fm10k_tlv_attr_put_u32(msg, FM10K_PF_ATTR_ID_PORT, lport_msg);

        /* load onto outgoing mailbox */
        return mbx->ops.enqueue_tx(hw, mbx, msg);
}

/**
 *  fm10k_configure_dglort_map_pf - Configures GLORT entry and queues
 *  @hw: pointer to hardware structure
 *  @dglort: pointer to dglort configuration structure
 *
 *  Reads the configuration structure contained in dglort_cfg and uses
 *  that information to then populate a DGLORTMAP/DEC entry and the queues
 *  to which it has been assigned.
 **/
static s32 fm10k_configure_dglort_map_pf(struct fm10k_hw *hw,
                                         struct fm10k_dglort_cfg *dglort)
{
        u16 glort, queue_count, vsi_count, pc_count;
        u16 vsi, queue, pc, q_idx;
        u32 txqctl, dglortdec, dglortmap;

        /* verify the dglort pointer */
        if (!dglort)
                return FM10K_ERR_PARAM;

        /* verify the dglort values */
        if ((dglort->idx > 7) || (dglort->rss_l > 7) || (dglort->pc_l > 3) ||
            (dglort->vsi_l > 6) || (dglort->vsi_b > 64) ||
            (dglort->queue_l > 8) || (dglort->queue_b >= 256))
                return FM10K_ERR_PARAM;

        /* determine count of VSIs and queues */
        queue_count = 1 << (dglort->rss_l + dglort->pc_l);
        vsi_count = 1 << (dglort->vsi_l + dglort->queue_l);
        glort = dglort->glort;
        q_idx = dglort->queue_b;

        /* configure SGLORT for queues */
        for (vsi = 0; vsi < vsi_count; vsi++, glort++) {
                for (queue = 0; queue < queue_count; queue++, q_idx++) {
                        if (q_idx >= FM10K_MAX_QUEUES)
                                break;

                        fm10k_write_reg(hw, FM10K_TX_SGLORT(q_idx), glort);
                        fm10k_write_reg(hw, FM10K_RX_SGLORT(q_idx), glort);
                }
        }

        /* determine count of PCs and queues */
        queue_count = 1 << (dglort->queue_l + dglort->rss_l + dglort->vsi_l);
        pc_count = 1 << dglort->pc_l;

        /* configure PC for Tx queues */
        for (pc = 0; pc < pc_count; pc++) {
                q_idx = pc + dglort->queue_b;
                for (queue = 0; queue < queue_count; queue++) {
                        if (q_idx >= FM10K_MAX_QUEUES)
                                break;

                        txqctl = fm10k_read_reg(hw, FM10K_TXQCTL(q_idx));
                        txqctl &= ~FM10K_TXQCTL_PC_MASK;
                        txqctl |= pc << FM10K_TXQCTL_PC_SHIFT;
                        fm10k_write_reg(hw, FM10K_TXQCTL(q_idx), txqctl);

                        q_idx += pc_count;
                }
        }

        /* configure DGLORTDEC */
        dglortdec = ((u32)(dglort->rss_l) << FM10K_DGLORTDEC_RSSLENGTH_SHIFT) |
                    ((u32)(dglort->queue_b) << FM10K_DGLORTDEC_QBASE_SHIFT) |
                    ((u32)(dglort->pc_l) << FM10K_DGLORTDEC_PCLENGTH_SHIFT) |
                    ((u32)(dglort->vsi_b) << FM10K_DGLORTDEC_VSIBASE_SHIFT) |
                    ((u32)(dglort->vsi_l) << FM10K_DGLORTDEC_VSILENGTH_SHIFT) |
                    ((u32)(dglort->queue_l));
        if (dglort->inner_rss)
                dglortdec |=  FM10K_DGLORTDEC_INNERRSS_ENABLE;

        /* configure DGLORTMAP */
        dglortmap = (dglort->idx == fm10k_dglort_default) ?
                        FM10K_DGLORTMAP_ANY : FM10K_DGLORTMAP_ZERO;
        dglortmap <<= dglort->vsi_l + dglort->queue_l + dglort->shared_l;
        dglortmap |= dglort->glort;

        /* write values to hardware */
        fm10k_write_reg(hw, FM10K_DGLORTDEC(dglort->idx), dglortdec);
        fm10k_write_reg(hw, FM10K_DGLORTMAP(dglort->idx), dglortmap);

        return 0;
}

u16 fm10k_queues_per_pool(struct fm10k_hw *hw)
{
        u16 num_pools = hw->iov.num_pools;

        return (num_pools > 32) ? 2 : (num_pools > 16) ? 4 : (num_pools > 8) ?
               8 : FM10K_MAX_QUEUES_POOL;
}

u16 fm10k_vf_queue_index(struct fm10k_hw *hw, u16 vf_idx)
{
        u16 num_vfs = hw->iov.num_vfs;
        u16 vf_q_idx = FM10K_MAX_QUEUES;

        vf_q_idx -= fm10k_queues_per_pool(hw) * (num_vfs - vf_idx);

        return vf_q_idx;
}

static u16 fm10k_vectors_per_pool(struct fm10k_hw *hw)
{
        u16 num_pools = hw->iov.num_pools;

        return (num_pools > 32) ? 8 : (num_pools > 16) ? 16 :
               FM10K_MAX_VECTORS_POOL;
}

static u16 fm10k_vf_vector_index(struct fm10k_hw *hw, u16 vf_idx)
{
        u16 vf_v_idx = FM10K_MAX_VECTORS_PF;

        vf_v_idx += fm10k_vectors_per_pool(hw) * vf_idx;

        return vf_v_idx;
}

/**
 *  fm10k_iov_assign_resources_pf - Assign pool resources for virtualization
 *  @hw: pointer to the HW structure
 *  @num_vfs: number of VFs to be allocated
 *  @num_pools: number of virtualization pools to be allocated
 *
 *  Allocates queues and traffic classes to virtualization entities to prepare
 *  the PF for SR-IOV and VMDq
 **/
static s32 fm10k_iov_assign_resources_pf(struct fm10k_hw *hw, u16 num_vfs,
                                         u16 num_pools)
{
        u16 qmap_stride, qpp, vpp, vf_q_idx, vf_q_idx0, qmap_idx;
        u32 vid = hw->mac.default_vid << FM10K_TXQCTL_VID_SHIFT;
        int i, j;

        /* hardware only supports up to 64 pools */
        if (num_pools > 64)
                return FM10K_ERR_PARAM;

        /* the number of VFs cannot exceed the number of pools */
        if ((num_vfs > num_pools) || (num_vfs > hw->iov.total_vfs))
                return FM10K_ERR_PARAM;

        /* record number of virtualization entities */
        hw->iov.num_vfs = num_vfs;
        hw->iov.num_pools = num_pools;

        /* determine qmap offsets and counts */
        qmap_stride = (num_vfs > 8) ? 32 : 256;
        qpp = fm10k_queues_per_pool(hw);
        vpp = fm10k_vectors_per_pool(hw);

        /* calculate starting index for queues */
        vf_q_idx = fm10k_vf_queue_index(hw, 0);
        qmap_idx = 0;

        /* establish TCs with -1 credits and no quanta to prevent transmit */
        for (i = 0; i < num_vfs; i++) {
                fm10k_write_reg(hw, FM10K_TC_MAXCREDIT(i), 0);
                fm10k_write_reg(hw, FM10K_TC_RATE(i), 0);
                fm10k_write_reg(hw, FM10K_TC_CREDIT(i),
                                FM10K_TC_CREDIT_CREDIT_MASK);
        }

        /* zero out all mbmem registers */
        for (i = FM10K_VFMBMEM_LEN * num_vfs; i--;)
                fm10k_write_reg(hw, FM10K_MBMEM(i), 0);

        /* clear event notification of VF FLR */
        fm10k_write_reg(hw, FM10K_PFVFLREC(0), ~0);
        fm10k_write_reg(hw, FM10K_PFVFLREC(1), ~0);

        /* loop through unallocated rings assigning them back to PF */
        for (i = FM10K_MAX_QUEUES_PF; i < vf_q_idx; i++) {
                fm10k_write_reg(hw, FM10K_TXDCTL(i), 0);
                fm10k_write_reg(hw, FM10K_TXQCTL(i), FM10K_TXQCTL_PF | vid);
                fm10k_write_reg(hw, FM10K_RXQCTL(i), FM10K_RXQCTL_PF);
        }

        /* PF should have already updated VFITR2[0] */

        /* update all ITR registers to flow to VFITR2[0] */
        for (i = FM10K_ITR_REG_COUNT_PF + 1; i < FM10K_ITR_REG_COUNT; i++) {
                if (!(i & (vpp - 1)))
                        fm10k_write_reg(hw, FM10K_ITR2(i), i - vpp);
                else
                        fm10k_write_reg(hw, FM10K_ITR2(i), i - 1);
        }

        /* update PF ITR2[0] to reference the last vector */
        fm10k_write_reg(hw, FM10K_ITR2(0),
                        fm10k_vf_vector_index(hw, num_vfs - 1));

        /* loop through rings populating rings and TCs */
        for (i = 0; i < num_vfs; i++) {
                /* record index for VF queue 0 for use in end of loop */
                vf_q_idx0 = vf_q_idx;

                for (j = 0; j < qpp; j++, qmap_idx++, vf_q_idx++) {
                        /* assign VF and locked TC to queues */
                        fm10k_write_reg(hw, FM10K_TXDCTL(vf_q_idx), 0);
                        fm10k_write_reg(hw, FM10K_TXQCTL(vf_q_idx),
                                        (i << FM10K_TXQCTL_TC_SHIFT) | i |
                                        FM10K_TXQCTL_VF | vid);
                        fm10k_write_reg(hw, FM10K_RXDCTL(vf_q_idx),
                                        FM10K_RXDCTL_WRITE_BACK_MIN_DELAY |
                                        FM10K_RXDCTL_DROP_ON_EMPTY);
                        fm10k_write_reg(hw, FM10K_RXQCTL(vf_q_idx),
                                        FM10K_RXQCTL_VF |
                                        (i << FM10K_RXQCTL_VF_SHIFT));

                        /* map queue pair to VF */
                        fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx), vf_q_idx);
                        fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx), vf_q_idx);
                }

                /* repeat the first ring for all of the remaining VF rings */
                for (; j < qmap_stride; j++, qmap_idx++) {
                        fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx), vf_q_idx0);
                        fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx), vf_q_idx0);
                }
        }

        /* loop through remaining indexes assigning all to queue 0 */
        while (qmap_idx < FM10K_TQMAP_TABLE_SIZE) {
                fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx), 0);
                fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx), 0);
                qmap_idx++;
        }

        return 0;
}

/**
 *  fm10k_iov_configure_tc_pf - Configure the shaping group for VF
 *  @hw: pointer to the HW structure
 *  @vf_idx: index of VF receiving GLORT
 *  @rate: Rate indicated in Mb/s
 *
 *  Configured the TC for a given VF to allow only up to a given number
 *  of Mb/s of outgoing Tx throughput.
 **/
static s32 fm10k_iov_configure_tc_pf(struct fm10k_hw *hw, u16 vf_idx, int rate)
{
        /* configure defaults */
        u32 interval = FM10K_TC_RATE_INTERVAL_4US_GEN3;
        u32 tc_rate = FM10K_TC_RATE_QUANTA_MASK;

        /* verify vf is in range */
        if (vf_idx >= hw->iov.num_vfs)
                return FM10K_ERR_PARAM;

        /* set interval to align with 4.096 usec in all modes */
        switch (hw->bus.speed) {
        case fm10k_bus_speed_2500:
                interval = FM10K_TC_RATE_INTERVAL_4US_GEN1;
                break;
        case fm10k_bus_speed_5000:
                interval = FM10K_TC_RATE_INTERVAL_4US_GEN2;
                break;
        default:
                break;
        }

        if (rate) {
                if (rate > FM10K_VF_TC_MAX || rate < FM10K_VF_TC_MIN)
                        return FM10K_ERR_PARAM;

                /* The quanta is measured in Bytes per 4.096 or 8.192 usec
                 * The rate is provided in Mbits per second
                 * To tralslate from rate to quanta we need to multiply the
                 * rate by 8.192 usec and divide by 8 bits/byte.  To avoid
                 * dealing with floating point we can round the values up
                 * to the nearest whole number ratio which gives us 128 / 125.
                 */
                tc_rate = (rate * 128) / 125;

                /* try to keep the rate limiting accurate by increasing
                 * the number of credits and interval for rates less than 4Gb/s
                 */
                if (rate < 4000)
                        interval <<= 1;
                else
                        tc_rate >>= 1;
        }

        /* update rate limiter with new values */
        fm10k_write_reg(hw, FM10K_TC_RATE(vf_idx), tc_rate | interval);
        fm10k_write_reg(hw, FM10K_TC_MAXCREDIT(vf_idx), FM10K_TC_MAXCREDIT_64K);
        fm10k_write_reg(hw, FM10K_TC_CREDIT(vf_idx), FM10K_TC_MAXCREDIT_64K);

        return 0;
}

/**
 *  fm10k_iov_assign_int_moderator_pf - Add VF interrupts to moderator list
 *  @hw: pointer to the HW structure
 *  @vf_idx: index of VF receiving GLORT
 *
 *  Update the interrupt moderator linked list to include any MSI-X
 *  interrupts which the VF has enabled in the MSI-X vector table.
 **/
static s32 fm10k_iov_assign_int_moderator_pf(struct fm10k_hw *hw, u16 vf_idx)
{
        u16 vf_v_idx, vf_v_limit, i;

        /* verify vf is in range */
        if (vf_idx >= hw->iov.num_vfs)
                return FM10K_ERR_PARAM;

        /* determine vector offset and count*/
        vf_v_idx = fm10k_vf_vector_index(hw, vf_idx);
        vf_v_limit = vf_v_idx + fm10k_vectors_per_pool(hw);

        /* search for first vector that is not masked */
        for (i = vf_v_limit - 1; i > vf_v_idx; i--) {
                if (!fm10k_read_reg(hw, FM10K_MSIX_VECTOR_MASK(i)))
                        break;
        }

        /* reset linked list so it now includes our active vectors */
        if (vf_idx == (hw->iov.num_vfs - 1))
                fm10k_write_reg(hw, FM10K_ITR2(0), i);
        else
                fm10k_write_reg(hw, FM10K_ITR2(vf_v_limit), i);

        return 0;
}

/**
 *  fm10k_iov_assign_default_mac_vlan_pf - Assign a MAC and VLAN to VF
 *  @hw: pointer to the HW structure
 *  @vf_info: pointer to VF information structure
 *
 *  Assign a MAC address and default VLAN to a VF and notify it of the update
 **/
static s32 fm10k_iov_assign_default_mac_vlan_pf(struct fm10k_hw *hw,
                                                struct fm10k_vf_info *vf_info)
{
        u16 qmap_stride, queues_per_pool, vf_q_idx, timeout, qmap_idx, i;
        u32 msg[4], txdctl, txqctl, tdbal = 0, tdbah = 0;
        s32 err = 0;
        u16 vf_idx, vf_vid;

        /* verify vf is in range */
        if (!vf_info || vf_info->vf_idx >= hw->iov.num_vfs)
                return FM10K_ERR_PARAM;

        /* determine qmap offsets and counts */
        qmap_stride = (hw->iov.num_vfs > 8) ? 32 : 256;
        queues_per_pool = fm10k_queues_per_pool(hw);

        /* calculate starting index for queues */
        vf_idx = vf_info->vf_idx;
        vf_q_idx = fm10k_vf_queue_index(hw, vf_idx);
        qmap_idx = qmap_stride * vf_idx;

        /* MAP Tx queue back to 0 temporarily, and disable it */
        fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx), 0);
        fm10k_write_reg(hw, FM10K_TXDCTL(vf_q_idx), 0);

        /* determine correct default VLAN ID */
        if (vf_info->pf_vid)
                vf_vid = vf_info->pf_vid | FM10K_VLAN_CLEAR;
        else
                vf_vid = vf_info->sw_vid;

        /* generate MAC_ADDR request */
        fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
        fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_DEFAULT_MAC,
                                    vf_info->mac, vf_vid);

        /* load onto outgoing mailbox, ignore any errors on enqueue */
        if (vf_info->mbx.ops.enqueue_tx)
                vf_info->mbx.ops.enqueue_tx(hw, &vf_info->mbx, msg);

        /* verify ring has disabled before modifying base address registers */
        txdctl = fm10k_read_reg(hw, FM10K_TXDCTL(vf_q_idx));
        for (timeout = 0; txdctl & FM10K_TXDCTL_ENABLE; timeout++) {
                /* limit ourselves to a 1ms timeout */
                if (timeout == 10) {
                        err = FM10K_ERR_DMA_PENDING;
                        goto err_out;
                }

                usleep_range(100, 200);
                txdctl = fm10k_read_reg(hw, FM10K_TXDCTL(vf_q_idx));
        }

        /* Update base address registers to contain MAC address */
        if (is_valid_ether_addr(vf_info->mac)) {
                tdbal = (((u32)vf_info->mac[3]) << 24) |
                        (((u32)vf_info->mac[4]) << 16) |
                        (((u32)vf_info->mac[5]) << 8);

                tdbah = (((u32)0xFF)            << 24) |
                        (((u32)vf_info->mac[0]) << 16) |
                        (((u32)vf_info->mac[1]) << 8) |
                        ((u32)vf_info->mac[2]);
        }

        /* Record the base address into queue 0 */
        fm10k_write_reg(hw, FM10K_TDBAL(vf_q_idx), tdbal);
        fm10k_write_reg(hw, FM10K_TDBAH(vf_q_idx), tdbah);

err_out:
        /* configure Queue control register */
        txqctl = ((u32)vf_vid << FM10K_TXQCTL_VID_SHIFT) &
                 FM10K_TXQCTL_VID_MASK;
        txqctl |= (vf_idx << FM10K_TXQCTL_TC_SHIFT) |
                  FM10K_TXQCTL_VF | vf_idx;

        /* assign VID */
        for (i = 0; i < queues_per_pool; i++)
                fm10k_write_reg(hw, FM10K_TXQCTL(vf_q_idx + i), txqctl);

        /* restore the queue back to VF ownership */
        fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx), vf_q_idx);
        return err;
}

/**
 *  fm10k_iov_reset_resources_pf - Reassign queues and interrupts to a VF
 *  @hw: pointer to the HW structure
 *  @vf_info: pointer to VF information structure
 *
 *  Reassign the interrupts and queues to a VF following an FLR
 **/
static s32 fm10k_iov_reset_resources_pf(struct fm10k_hw *hw,
                                        struct fm10k_vf_info *vf_info)
{
        u16 qmap_stride, queues_per_pool, vf_q_idx, qmap_idx;
        u32 tdbal = 0, tdbah = 0, txqctl, rxqctl;
        u16 vf_v_idx, vf_v_limit, vf_vid;
        u8 vf_idx = vf_info->vf_idx;
        int i;

        /* verify vf is in range */
        if (vf_idx >= hw->iov.num_vfs)
                return FM10K_ERR_PARAM;

        /* clear event notification of VF FLR */
        fm10k_write_reg(hw, FM10K_PFVFLREC(vf_idx / 32), 1 << (vf_idx % 32));

        /* force timeout and then disconnect the mailbox */
        vf_info->mbx.timeout = 0;
        if (vf_info->mbx.ops.disconnect)
                vf_info->mbx.ops.disconnect(hw, &vf_info->mbx);

        /* determine vector offset and count*/
        vf_v_idx = fm10k_vf_vector_index(hw, vf_idx);
        vf_v_limit = vf_v_idx + fm10k_vectors_per_pool(hw);

        /* determine qmap offsets and counts */
        qmap_stride = (hw->iov.num_vfs > 8) ? 32 : 256;
        queues_per_pool = fm10k_queues_per_pool(hw);
        qmap_idx = qmap_stride * vf_idx;

        /* make all the queues inaccessible to the VF */
        for (i = qmap_idx; i < (qmap_idx + qmap_stride); i++) {
                fm10k_write_reg(hw, FM10K_TQMAP(i), 0);
                fm10k_write_reg(hw, FM10K_RQMAP(i), 0);
        }

        /* calculate starting index for queues */
        vf_q_idx = fm10k_vf_queue_index(hw, vf_idx);

        /* determine correct default VLAN ID */
        if (vf_info->pf_vid)
                vf_vid = vf_info->pf_vid;
        else
                vf_vid = vf_info->sw_vid;

        /* configure Queue control register */
        txqctl = ((u32)vf_vid << FM10K_TXQCTL_VID_SHIFT) |
                 (vf_idx << FM10K_TXQCTL_TC_SHIFT) |
                 FM10K_TXQCTL_VF | vf_idx;
        rxqctl = FM10K_RXQCTL_VF | (vf_idx << FM10K_RXQCTL_VF_SHIFT);

        /* stop further DMA and reset queue ownership back to VF */
        for (i = vf_q_idx; i < (queues_per_pool + vf_q_idx); i++) {
                fm10k_write_reg(hw, FM10K_TXDCTL(i), 0);
                fm10k_write_reg(hw, FM10K_TXQCTL(i), txqctl);
                fm10k_write_reg(hw, FM10K_RXDCTL(i),
                                FM10K_RXDCTL_WRITE_BACK_MIN_DELAY |
                                FM10K_RXDCTL_DROP_ON_EMPTY);
                fm10k_write_reg(hw, FM10K_RXQCTL(i), rxqctl);
        }

        /* reset TC with -1 credits and no quanta to prevent transmit */
        fm10k_write_reg(hw, FM10K_TC_MAXCREDIT(vf_idx), 0);
        fm10k_write_reg(hw, FM10K_TC_RATE(vf_idx), 0);
        fm10k_write_reg(hw, FM10K_TC_CREDIT(vf_idx),

                        FM10K_TC_CREDIT_CREDIT_MASK);

        /* update our first entry in the table based on previous VF */
        if (!vf_idx)
                hw->mac.ops.update_int_moderator(hw);
        else
                hw->iov.ops.assign_int_moderator(hw, vf_idx - 1);

        /* reset linked list so it now includes our active vectors */
        if (vf_idx == (hw->iov.num_vfs - 1))
                fm10k_write_reg(hw, FM10K_ITR2(0), vf_v_idx);
        else
                fm10k_write_reg(hw, FM10K_ITR2(vf_v_limit), vf_v_idx);

        /* link remaining vectors so that next points to previous */
        for (vf_v_idx++; vf_v_idx < vf_v_limit; vf_v_idx++)
                fm10k_write_reg(hw, FM10K_ITR2(vf_v_idx), vf_v_idx - 1);

        /* zero out MBMEM, VLAN_TABLE, RETA, RSSRK, and MRQC registers */
        for (i = FM10K_VFMBMEM_LEN; i--;)
                fm10k_write_reg(hw, FM10K_MBMEM_VF(vf_idx, i), 0);
        for (i = FM10K_VLAN_TABLE_SIZE; i--;)
                fm10k_write_reg(hw, FM10K_VLAN_TABLE(vf_info->vsi, i), 0);
        for (i = FM10K_RETA_SIZE; i--;)
                fm10k_write_reg(hw, FM10K_RETA(vf_info->vsi, i), 0);
        for (i = FM10K_RSSRK_SIZE; i--;)
                fm10k_write_reg(hw, FM10K_RSSRK(vf_info->vsi, i), 0);
        fm10k_write_reg(hw, FM10K_MRQC(vf_info->vsi), 0);

        /* Update base address registers to contain MAC address */
        if (is_valid_ether_addr(vf_info->mac)) {
                tdbal = (((u32)vf_info->mac[3]) << 24) |
                        (((u32)vf_info->mac[4]) << 16) |
                        (((u32)vf_info->mac[5]) << 8);
                tdbah = (((u32)0xFF)       << 24) |
                        (((u32)vf_info->mac[0]) << 16) |
                        (((u32)vf_info->mac[1]) << 8) |
                        ((u32)vf_info->mac[2]);
        }

        /* map queue pairs back to VF from last to first*/
        for (i = queues_per_pool; i--;) {
                fm10k_write_reg(hw, FM10K_TDBAL(vf_q_idx + i), tdbal);
                fm10k_write_reg(hw, FM10K_TDBAH(vf_q_idx + i), tdbah);
                fm10k_write_reg(hw, FM10K_TQMAP(qmap_idx + i), vf_q_idx + i);
                fm10k_write_reg(hw, FM10K_RQMAP(qmap_idx + i), vf_q_idx + i);
        }

        return 0;
}

/**
 *  fm10k_iov_set_lport_pf - Assign and enable a logical port for a given VF
 *  @hw: pointer to hardware structure
 *  @vf_info: pointer to VF information structure
 *  @lport_idx: Logical port offset from the hardware glort
 *  @flags: Set of capability flags to extend port beyond basic functionality
 *
 *  This function allows enabling a VF port by assigning it a GLORT and
 *  setting the flags so that it can enable an Rx mode.
 **/
static s32 fm10k_iov_set_lport_pf(struct fm10k_hw *hw,
                                  struct fm10k_vf_info *vf_info,
                                  u16 lport_idx, u8 flags)
{
        u16 glort = (hw->mac.dglort_map + lport_idx) & FM10K_DGLORTMAP_NONE;

        /* if glort is not valid return error */
        if (!fm10k_glort_valid_pf(hw, glort))
                return FM10K_ERR_PARAM;

        vf_info->vf_flags = flags | FM10K_VF_FLAG_NONE_CAPABLE;
        vf_info->glort = glort;

        return 0;
}

/**
 *  fm10k_iov_reset_lport_pf - Disable a logical port for a given VF
 *  @hw: pointer to hardware structure
 *  @vf_info: pointer to VF information structure
 *
 *  This function disables a VF port by stripping it of a GLORT and
 *  setting the flags so that it cannot enable any Rx mode.
 **/
static void fm10k_iov_reset_lport_pf(struct fm10k_hw *hw,
                                     struct fm10k_vf_info *vf_info)
{
        u32 msg[1];

        /* need to disable the port if it is already enabled */
        if (FM10K_VF_FLAG_ENABLED(vf_info)) {
                /* notify switch that this port has been disabled */
                fm10k_update_lport_state_pf(hw, vf_info->glort, 1, false);

                /* generate port state response to notify VF it is not ready */
                fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
                vf_info->mbx.ops.enqueue_tx(hw, &vf_info->mbx, msg);
        }

        /* clear flags and glort if it exists */
        vf_info->vf_flags = 0;
        vf_info->glort = 0;
}

/**
 *  fm10k_iov_update_stats_pf - Updates hardware related statistics for VFs
 *  @hw: pointer to hardware structure
 *  @q: stats for all queues of a VF
 *  @vf_idx: index of VF
 *
 *  This function collects queue stats for VFs.
 **/
static void fm10k_iov_update_stats_pf(struct fm10k_hw *hw,
                                      struct fm10k_hw_stats_q *q,
                                      u16 vf_idx)
{
        u32 idx, qpp;

        /* get stats for all of the queues */
        qpp = fm10k_queues_per_pool(hw);
        idx = fm10k_vf_queue_index(hw, vf_idx);
        fm10k_update_hw_stats_q(hw, q, idx, qpp);
}

static s32 fm10k_iov_report_timestamp_pf(struct fm10k_hw *hw,
                                         struct fm10k_vf_info *vf_info,
                                         u64 timestamp)
{
        u32 msg[4];

        /* generate port state response to notify VF it is not ready */
        fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_1588);
        fm10k_tlv_attr_put_u64(msg, FM10K_1588_MSG_TIMESTAMP, timestamp);

        return vf_info->mbx.ops.enqueue_tx(hw, &vf_info->mbx, msg);
}

/**
 *  fm10k_iov_msg_msix_pf - Message handler for MSI-X request from VF
 *  @hw: Pointer to hardware structure
 *  @results: Pointer array to message, results[0] is pointer to message
 *  @mbx: Pointer to mailbox information structure
 *
 *  This function is a default handler for MSI-X requests from the VF.  The
 *  assumption is that in this case it is acceptable to just directly
 *  hand off the message form the VF to the underlying shared code.
 **/
s32 fm10k_iov_msg_msix_pf(struct fm10k_hw *hw, u32 **results,
                          struct fm10k_mbx_info *mbx)
{
        struct fm10k_vf_info *vf_info = (struct fm10k_vf_info *)mbx;
        u8 vf_idx = vf_info->vf_idx;

        return hw->iov.ops.assign_int_moderator(hw, vf_idx);
}

/**
 *  fm10k_iov_msg_mac_vlan_pf - Message handler for MAC/VLAN request from VF
 *  @hw: Pointer to hardware structure
 *  @results: Pointer array to message, results[0] is pointer to message
 *  @mbx: Pointer to mailbox information structure
 *
 *  This function is a default handler for MAC/VLAN requests from the VF.
 *  The assumption is that in this case it is acceptable to just directly
 *  hand off the message form the VF to the underlying shared code.
 **/
s32 fm10k_iov_msg_mac_vlan_pf(struct fm10k_hw *hw, u32 **results,
                              struct fm10k_mbx_info *mbx)
{
        struct fm10k_vf_info *vf_info = (struct fm10k_vf_info *)mbx;
        int err = 0;
        u8 mac[ETH_ALEN];
        u32 *result;
        u16 vlan;
        u32 vid;

        /* we shouldn't be updating rules on a disabled interface */
        if (!FM10K_VF_FLAG_ENABLED(vf_info))
                err = FM10K_ERR_PARAM;

        if (!err && !!results[FM10K_MAC_VLAN_MSG_VLAN]) {
                result = results[FM10K_MAC_VLAN_MSG_VLAN];

                /* record VLAN id requested */
                err = fm10k_tlv_attr_get_u32(result, &vid);
                if (err)
                        return err;

                /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
                if (!vid || (vid == FM10K_VLAN_CLEAR)) {
                        if (vf_info->pf_vid)
                                vid |= vf_info->pf_vid;
                        else
                                vid |= vf_info->sw_vid;
                } else if (vid != vf_info->pf_vid) {
                        return FM10K_ERR_PARAM;
                }

                /* update VSI info for VF in regards to VLAN table */
                err = hw->mac.ops.update_vlan(hw, vid, vf_info->vsi,
                                              !(vid & FM10K_VLAN_CLEAR));
        }

        if (!err && !!results[FM10K_MAC_VLAN_MSG_MAC]) {
                result = results[FM10K_MAC_VLAN_MSG_MAC];

                /* record unicast MAC address requested */
                err = fm10k_tlv_attr_get_mac_vlan(result, mac, &vlan);
                if (err)
                        return err;

                /* block attempts to set MAC for a locked device */
                if (is_valid_ether_addr(vf_info->mac) &&
                    memcmp(mac, vf_info->mac, ETH_ALEN))
                        return FM10K_ERR_PARAM;

                /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
                if (!vlan || (vlan == FM10K_VLAN_CLEAR)) {
                        if (vf_info->pf_vid)
                                vlan |= vf_info->pf_vid;
                        else
                                vlan |= vf_info->sw_vid;
                } else if (vf_info->pf_vid) {
                        return FM10K_ERR_PARAM;
                }

                /* notify switch of request for new unicast address */
                err = hw->mac.ops.update_uc_addr(hw, vf_info->glort, mac, vlan,
                                                 !(vlan & FM10K_VLAN_CLEAR), 0);
        }

        if (!err && !!results[FM10K_MAC_VLAN_MSG_MULTICAST]) {
                result = results[FM10K_MAC_VLAN_MSG_MULTICAST];

                /* record multicast MAC address requested */
                err = fm10k_tlv_attr_get_mac_vlan(result, mac, &vlan);
                if (err)
                        return err;

                /* verify that the VF is allowed to request multicast */
                if (!(vf_info->vf_flags & FM10K_VF_FLAG_MULTI_ENABLED))
                        return FM10K_ERR_PARAM;

                /* if VLAN ID is 0, set the default VLAN ID instead of 0 */
                if (!vlan || (vlan == FM10K_VLAN_CLEAR)) {
                        if (vf_info->pf_vid)
                                vlan |= vf_info->pf_vid;
                        else
                                vlan |= vf_info->sw_vid;
                } else if (vf_info->pf_vid) {
                        return FM10K_ERR_PARAM;
                }

                /* notify switch of request for new multicast address */
                err = hw->mac.ops.update_mc_addr(hw, vf_info->glort, mac,
                                                 !(vlan & FM10K_VLAN_CLEAR), 0);
        }

        return err;
}

/**
 *  fm10k_iov_supported_xcast_mode_pf - Determine best match for xcast mode
 *  @vf_info: VF info structure containing capability flags
 *  @mode: Requested xcast mode
 *
 *  This function outputs the mode that most closely matches the requested
 *  mode.  If not modes match it will request we disable the port
 **/
static u8 fm10k_iov_supported_xcast_mode_pf(struct fm10k_vf_info *vf_info,
                                            u8 mode)
{
        u8 vf_flags = vf_info->vf_flags;

        /* match up mode to capabilities as best as possible */
        switch (mode) {
        case FM10K_XCAST_MODE_PROMISC:
                if (vf_flags & FM10K_VF_FLAG_PROMISC_CAPABLE)
                        return FM10K_XCAST_MODE_PROMISC;
                /* fallthough */
        case FM10K_XCAST_MODE_ALLMULTI:
                if (vf_flags & FM10K_VF_FLAG_ALLMULTI_CAPABLE)
                        return FM10K_XCAST_MODE_ALLMULTI;
                /* fallthough */
        case FM10K_XCAST_MODE_MULTI:
                if (vf_flags & FM10K_VF_FLAG_MULTI_CAPABLE)
                        return FM10K_XCAST_MODE_MULTI;
                /* fallthough */
        case FM10K_XCAST_MODE_NONE:
                if (vf_flags & FM10K_VF_FLAG_NONE_CAPABLE)
                        return FM10K_XCAST_MODE_NONE;
                /* fallthough */
        default:
                break;
        }

        /* disable interface as it should not be able to request any */
        return FM10K_XCAST_MODE_DISABLE;
}

/**
 *  fm10k_iov_msg_lport_state_pf - Message handler for port state requests
 *  @hw: Pointer to hardware structure
 *  @results: Pointer array to message, results[0] is pointer to message
 *  @mbx: Pointer to mailbox information structure
 *
 *  This function is a default handler for port state requests.  The port
 *  state requests for now are basic and consist of enabling or disabling
 *  the port.
 **/
s32 fm10k_iov_msg_lport_state_pf(struct fm10k_hw *hw, u32 **results,
                                 struct fm10k_mbx_info *mbx)
{
        struct fm10k_vf_info *vf_info = (struct fm10k_vf_info *)mbx;
        u32 *result;
        s32 err = 0;
        u32 msg[2];
        u8 mode = 0;

        /* verify VF is allowed to enable even minimal mode */
        if (!(vf_info->vf_flags & FM10K_VF_FLAG_NONE_CAPABLE))
                return FM10K_ERR_PARAM;

        if (!!results[FM10K_LPORT_STATE_MSG_XCAST_MODE]) {
                result = results[FM10K_LPORT_STATE_MSG_XCAST_MODE];

                /* XCAST mode update requested */
                err = fm10k_tlv_attr_get_u8(result, &mode);
                if (err)
                        return FM10K_ERR_PARAM;

                /* prep for possible demotion depending on capabilities */
                mode = fm10k_iov_supported_xcast_mode_pf(vf_info, mode);

                /* if mode is not currently enabled, enable it */
                if (!(FM10K_VF_FLAG_ENABLED(vf_info) & (1 << mode)))
                        fm10k_update_xcast_mode_pf(hw, vf_info->glort, mode);

                /* swap mode back to a bit flag */
                mode = FM10K_VF_FLAG_SET_MODE(mode);
        } else if (!results[FM10K_LPORT_STATE_MSG_DISABLE]) {
                /* need to disable the port if it is already enabled */
                if (FM10K_VF_FLAG_ENABLED(vf_info))
                        err = fm10k_update_lport_state_pf(hw, vf_info->glort,
                                                          1, false);

                /* when enabling the port we should reset the rate limiters */
                hw->iov.ops.configure_tc(hw, vf_info->vf_idx, vf_info->rate);

                /* set mode for minimal functionality */
                mode = FM10K_VF_FLAG_SET_MODE_NONE;

                /* generate port state response to notify VF it is ready */
                fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
                fm10k_tlv_attr_put_bool(msg, FM10K_LPORT_STATE_MSG_READY);
                mbx->ops.enqueue_tx(hw, mbx, msg);
        }

        /* if enable state toggled note the update */
        if (!err && (!FM10K_VF_FLAG_ENABLED(vf_info) != !mode))
                err = fm10k_update_lport_state_pf(hw, vf_info->glort, 1,
                                                  !!mode);

        /* if state change succeeded, then update our stored state */
        mode |= FM10K_VF_FLAG_CAPABLE(vf_info);
        if (!err)
                vf_info->vf_flags = mode;

        return err;
}

const struct fm10k_msg_data fm10k_iov_msg_data_pf[] = {
        FM10K_TLV_MSG_TEST_HANDLER(fm10k_tlv_msg_test),
        FM10K_VF_MSG_MSIX_HANDLER(fm10k_iov_msg_msix_pf),
        FM10K_VF_MSG_MAC_VLAN_HANDLER(fm10k_iov_msg_mac_vlan_pf),
        FM10K_VF_MSG_LPORT_STATE_HANDLER(fm10k_iov_msg_lport_state_pf),
        FM10K_TLV_MSG_ERROR_HANDLER(fm10k_tlv_msg_error),
};

/**
 *  fm10k_update_stats_hw_pf - Updates hardware related statistics of PF
 *  @hw: pointer to hardware structure
 *  @stats: pointer to the stats structure to update
 *
 *  This function collects and aggregates global and per queue hardware
 *  statistics.
 **/
static void fm10k_update_hw_stats_pf(struct fm10k_hw *hw,
                                     struct fm10k_hw_stats *stats)
{
        u32 timeout, ur, ca, um, xec, vlan_drop, loopback_drop, nodesc_drop;
        u32 id, id_prev;

        /* Use Tx queue 0 as a canary to detect a reset */
        id = fm10k_read_reg(hw, FM10K_TXQCTL(0));

        /* Read Global Statistics */
        do {
                timeout = fm10k_read_hw_stats_32b(hw, FM10K_STATS_TIMEOUT,
                                                  &stats->timeout);
                ur = fm10k_read_hw_stats_32b(hw, FM10K_STATS_UR, &stats->ur);
                ca = fm10k_read_hw_stats_32b(hw, FM10K_STATS_CA, &stats->ca);
                um = fm10k_read_hw_stats_32b(hw, FM10K_STATS_UM, &stats->um);
                xec = fm10k_read_hw_stats_32b(hw, FM10K_STATS_XEC, &stats->xec);
                vlan_drop = fm10k_read_hw_stats_32b(hw, FM10K_STATS_VLAN_DROP,
                                                    &stats->vlan_drop);
                loopback_drop = fm10k_read_hw_stats_32b(hw,
                                                        FM10K_STATS_LOOPBACK_DROP,
                                                     &stats->loopback_drop);
                nodesc_drop = fm10k_read_hw_stats_32b(hw,
                                                      FM10K_STATS_NODESC_DROP,
                                                      &stats->nodesc_drop);

                /* if value has not changed then we have consistent data */
                id_prev = id;
                id = fm10k_read_reg(hw, FM10K_TXQCTL(0));
        } while ((id ^ id_prev) & FM10K_TXQCTL_ID_MASK);

        /* drop non-ID bits and set VALID ID bit */
        id &= FM10K_TXQCTL_ID_MASK;
        id |= FM10K_STAT_VALID;

        /* Update Global Statistics */
        if (stats->stats_idx == id) {
                stats->timeout.count += timeout;
                stats->ur.count += ur;
                stats->ca.count += ca;
                stats->um.count += um;
                stats->xec.count += xec;
                stats->vlan_drop.count += vlan_drop;
                stats->loopback_drop.count += loopback_drop;
                stats->nodesc_drop.count += nodesc_drop;
        }

        /* Update bases and record current PF id */
        fm10k_update_hw_base_32b(&stats->timeout, timeout);
        fm10k_update_hw_base_32b(&stats->ur, ur);
        fm10k_update_hw_base_32b(&stats->ca, ca);
        fm10k_update_hw_base_32b(&stats->um, um);
        fm10k_update_hw_base_32b(&stats->xec, xec);
        fm10k_update_hw_base_32b(&stats->vlan_drop, vlan_drop);
        fm10k_update_hw_base_32b(&stats->loopback_drop, loopback_drop);
        fm10k_update_hw_base_32b(&stats->nodesc_drop, nodesc_drop);
        stats->stats_idx = id;

        /* Update Queue Statistics */
        fm10k_update_hw_stats_q(hw, stats->q, 0, hw->mac.max_queues);
}

/**
 *  fm10k_rebind_hw_stats_pf - Resets base for hardware statistics of PF
 *  @hw: pointer to hardware structure
 *  @stats: pointer to the stats structure to update
 *
 *  This function resets the base for global and per queue hardware
 *  statistics.
 **/
static void fm10k_rebind_hw_stats_pf(struct fm10k_hw *hw,
                                     struct fm10k_hw_stats *stats)
{
        /* Unbind Global Statistics */
        fm10k_unbind_hw_stats_32b(&stats->timeout);
        fm10k_unbind_hw_stats_32b(&stats->ur);
        fm10k_unbind_hw_stats_32b(&stats->ca);
        fm10k_unbind_hw_stats_32b(&stats->um);
        fm10k_unbind_hw_stats_32b(&stats->xec);
        fm10k_unbind_hw_stats_32b(&stats->vlan_drop);
        fm10k_unbind_hw_stats_32b(&stats->loopback_drop);
        fm10k_unbind_hw_stats_32b(&stats->nodesc_drop);

        /* Unbind Queue Statistics */
        fm10k_unbind_hw_stats_q(stats->q, 0, hw->mac.max_queues);

        /* Reinitialize bases for all stats */
        fm10k_update_hw_stats_pf(hw, stats);
}

/**
 *  fm10k_set_dma_mask_pf - Configures PhyAddrSpace to limit DMA to system
 *  @hw: pointer to hardware structure
 *  @dma_mask: 64 bit DMA mask required for platform
 *
 *  This function sets the PHYADDR.PhyAddrSpace bits for the endpoint in order
 *  to limit the access to memory beyond what is physically in the system.
 **/
static void fm10k_set_dma_mask_pf(struct fm10k_hw *hw, u64 dma_mask)
{
        /* we need to write the upper 32 bits of DMA mask to PhyAddrSpace */
        u32 phyaddr = (u32)(dma_mask >> 32);

        fm10k_write_reg(hw, FM10K_PHYADDR, phyaddr);
}

/**
 *  fm10k_get_fault_pf - Record a fault in one of the interface units
 *  @hw: pointer to hardware structure
 *  @type: pointer to fault type register offset
 *  @fault: pointer to memory location to record the fault
 *
 *  Record the fault register contents to the fault data structure and
 *  clear the entry from the register.
 *
 *  Returns ERR_PARAM if invalid register is specified or no error is present.
 **/
static s32 fm10k_get_fault_pf(struct fm10k_hw *hw, int type,
                              struct fm10k_fault *fault)
{
        u32 func;

        /* verify the fault register is in range and is aligned */
        switch (type) {
        case FM10K_PCA_FAULT:
        case FM10K_THI_FAULT:
        case FM10K_FUM_FAULT:
                break;
        default:
                return FM10K_ERR_PARAM;
        }

        /* only service faults that are valid */
        func = fm10k_read_reg(hw, type + FM10K_FAULT_FUNC);
        if (!(func & FM10K_FAULT_FUNC_VALID))
                return FM10K_ERR_PARAM;

        /* read remaining fields */
        fault->address = fm10k_read_reg(hw, type + FM10K_FAULT_ADDR_HI);
        fault->address <<= 32;
        fault->address = fm10k_read_reg(hw, type + FM10K_FAULT_ADDR_LO);
        fault->specinfo = fm10k_read_reg(hw, type + FM10K_FAULT_SPECINFO);

        /* clear valid bit to allow for next error */
        fm10k_write_reg(hw, type + FM10K_FAULT_FUNC, FM10K_FAULT_FUNC_VALID);

        /* Record which function triggered the error */
        if (func & FM10K_FAULT_FUNC_PF)
                fault->func = 0;
        else
                fault->func = 1 + ((func & FM10K_FAULT_FUNC_VF_MASK) >>
                                   FM10K_FAULT_FUNC_VF_SHIFT);

        /* record fault type */
        fault->type = func & FM10K_FAULT_FUNC_TYPE_MASK;

        return 0;
}

/**
 *  fm10k_request_lport_map_pf - Request LPORT map from the switch API
 *  @hw: pointer to hardware structure
 *
 **/
static s32 fm10k_request_lport_map_pf(struct fm10k_hw *hw)
{
        struct fm10k_mbx_info *mbx = &hw->mbx;
        u32 msg[1];

        /* issue request asking for LPORT map */
        fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_LPORT_MAP);

        /* load onto outgoing mailbox */
        return mbx->ops.enqueue_tx(hw, mbx, msg);
}

/**
 *  fm10k_get_host_state_pf - Returns the state of the switch and mailbox
 *  @hw: pointer to hardware structure
 *  @switch_ready: pointer to boolean value that will record switch state
 *
 *  This funciton will check the DMA_CTRL2 register and mailbox in order
 *  to determine if the switch is ready for the PF to begin requesting
 *  addresses and mapping traffic to the local interface.
 **/
static s32 fm10k_get_host_state_pf(struct fm10k_hw *hw, bool *switch_ready)
{
        s32 ret_val = 0;
        u32 dma_ctrl2;

        /* verify the switch is ready for interraction */
        dma_ctrl2 = fm10k_read_reg(hw, FM10K_DMA_CTRL2);
        if (!(dma_ctrl2 & FM10K_DMA_CTRL2_SWITCH_READY))
                goto out;

        /* retrieve generic host state info */
        ret_val = fm10k_get_host_state_generic(hw, switch_ready);
        if (ret_val)
                goto out;

        /* interface cannot receive traffic without logical ports */
        if (hw->mac.dglort_map == FM10K_DGLORTMAP_NONE)
                ret_val = fm10k_request_lport_map_pf(hw);

out:
        return ret_val;
}

/* This structure defines the attibutes to be parsed below */
const struct fm10k_tlv_attr fm10k_lport_map_msg_attr[] = {
        FM10K_TLV_ATTR_U32(FM10K_PF_ATTR_ID_LPORT_MAP),
        FM10K_TLV_ATTR_LAST
};

/**
 *  fm10k_msg_lport_map_pf - Message handler for lport_map message from SM
 *  @hw: Pointer to hardware structure
 *  @results: pointer array containing parsed data
 *  @mbx: Pointer to mailbox information structure
 *
 *  This handler configures the lport mapping based on the reply from the
 *  switch API.
 **/
s32 fm10k_msg_lport_map_pf(struct fm10k_hw *hw, u32 **results,
                           struct fm10k_mbx_info *mbx)
{
        u16 glort, mask;
        u32 dglort_map;
        s32 err;

        err = fm10k_tlv_attr_get_u32(results[FM10K_PF_ATTR_ID_LPORT_MAP],
                                     &dglort_map);
        if (err)
                return err;

        /* extract values out of the header */
        glort = FM10K_MSG_HDR_FIELD_GET(dglort_map, LPORT_MAP_GLORT);
        mask = FM10K_MSG_HDR_FIELD_GET(dglort_map, LPORT_MAP_MASK);

        /* verify mask is set and none of the masked bits in glort are set */
        if (!mask || (glort & ~mask))
                return FM10K_ERR_PARAM;

        /* verify the mask is contiguous, and that it is 1's followed by 0's */
        if (((~(mask - 1) & mask) + mask) & FM10K_DGLORTMAP_NONE)
                return FM10K_ERR_PARAM;

        /* record the glort, mask, and port count */
        hw->mac.dglort_map = dglort_map;

        return 0;
}

const struct fm10k_tlv_attr fm10k_update_pvid_msg_attr[] = {
        FM10K_TLV_ATTR_U32(FM10K_PF_ATTR_ID_UPDATE_PVID),
        FM10K_TLV_ATTR_LAST
};

/**
 *  fm10k_msg_update_pvid_pf - Message handler for port VLAN message from SM
 *  @hw: Pointer to hardware structure
 *  @results: pointer array containing parsed data
 *  @mbx: Pointer to mailbox information structure
 *
 *  This handler configures the default VLAN for the PF
 **/
s32 fm10k_msg_update_pvid_pf(struct fm10k_hw *hw, u32 **results,
                             struct fm10k_mbx_info *mbx)
{
        u16 glort, pvid;
        u32 pvid_update;
        s32 err;

        err = fm10k_tlv_attr_get_u32(results[FM10K_PF_ATTR_ID_UPDATE_PVID],
                                     &pvid_update);
        if (err)
                return err;

        /* extract values from the pvid update */
        glort = FM10K_MSG_HDR_FIELD_GET(pvid_update, UPDATE_PVID_GLORT);
        pvid = FM10K_MSG_HDR_FIELD_GET(pvid_update, UPDATE_PVID_PVID);

        /* if glort is not valid return error */
        if (!fm10k_glort_valid_pf(hw, glort))
                return FM10K_ERR_PARAM;

        /* verify VID is valid */
        if (pvid >= FM10K_VLAN_TABLE_VID_MAX)
                return FM10K_ERR_PARAM;

        /* record the port VLAN ID value */
        hw->mac.default_vid = pvid;

        return 0;
}

/**
 *  fm10k_record_global_table_data - Move global table data to swapi table info
 *  @from: pointer to source table data structure
 *  @to: pointer to destination table info structure
 *
 *  This function is will copy table_data to the table_info contained in
 *  the hw struct.
 **/
static void fm10k_record_global_table_data(struct fm10k_global_table_data *from,
                                           struct fm10k_swapi_table_info *to)
{
        /* convert from le32 struct to CPU byte ordered values */
        to->used = le32_to_cpu(from->used);
        to->avail = le32_to_cpu(from->avail);
}

const struct fm10k_tlv_attr fm10k_err_msg_attr[] = {
        FM10K_TLV_ATTR_LE_STRUCT(FM10K_PF_ATTR_ID_ERR,
                                 sizeof(struct fm10k_swapi_error)),
        FM10K_TLV_ATTR_LAST
};

/**
 *  fm10k_msg_err_pf - Message handler for error reply
 *  @hw: Pointer to hardware structure
 *  @results: pointer array containing parsed data
 *  @mbx: Pointer to mailbox information structure
 *
 *  This handler will capture the data for any error replies to previous
 *  messages that the PF has sent.
 **/
s32 fm10k_msg_err_pf(struct fm10k_hw *hw, u32 **results,
                     struct fm10k_mbx_info *mbx)
{
        struct fm10k_swapi_error err_msg;
        s32 err;

        /* extract structure from message */
        err = fm10k_tlv_attr_get_le_struct(results[FM10K_PF_ATTR_ID_ERR],
                                           &err_msg, sizeof(err_msg));
        if (err)
                return err;

        /* record table status */
        fm10k_record_global_table_data(&err_msg.mac, &hw->swapi.mac);
        fm10k_record_global_table_data(&err_msg.nexthop, &hw->swapi.nexthop);
        fm10k_record_global_table_data(&err_msg.ffu, &hw->swapi.ffu);

        /* record SW API status value */
        hw->swapi.status = le32_to_cpu(err_msg.status);

        return 0;
}

const struct fm10k_tlv_attr fm10k_1588_timestamp_msg_attr[] = {
        FM10K_TLV_ATTR_LE_STRUCT(FM10K_PF_ATTR_ID_1588_TIMESTAMP,
                                 sizeof(struct fm10k_swapi_1588_timestamp)),
        FM10K_TLV_ATTR_LAST
};

/* currently there is no shared 1588 timestamp handler */

/**
 *  fm10k_adjust_systime_pf - Adjust systime frequency
 *  @hw: pointer to hardware structure
 *  @ppb: adjustment rate in parts per billion
 *
 *  This function will adjust the SYSTIME_CFG register contained in BAR 4
 *  if this function is supported for BAR 4 access.  The adjustment amount
 *  is based on the parts per billion value provided and adjusted to a
 *  value based on parts per 2^48 clock cycles.
 *
 *  If adjustment is not supported or the requested value is too large
 *  we will return an error.
 **/
static s32 fm10k_adjust_systime_pf(struct fm10k_hw *hw, s32 ppb)
{
        u64 systime_adjust;

        /* if sw_addr is not set we don't have switch register access */
        if (!hw->sw_addr)
                return ppb ? FM10K_ERR_PARAM : 0;

        /* we must convert the value from parts per billion to parts per
         * 2^48 cycles.  In addition I have opted to only use the 30 most
         * significant bits of the adjustment value as the 8 least
         * significant bits are located in another register and represent
         * a value significantly less than a part per billion, the result
         * of dropping the 8 least significant bits is that the adjustment
         * value is effectively multiplied by 2^8 when we write it.
         *
         * As a result of all this the math for this breaks down as follows:
         *      ppb / 10^9 == adjust * 2^8 / 2^48
         * If we solve this for adjust, and simplify it comes out as:
         *      ppb * 2^31 / 5^9 == adjust
         */
        systime_adjust = (ppb < 0) ? -ppb : ppb;
        systime_adjust <<= 31;
        do_div(systime_adjust, 1953125);

        /* verify the requested adjustment value is in range */
        if (systime_adjust > FM10K_SW_SYSTIME_ADJUST_MASK)
                return FM10K_ERR_PARAM;

        if (ppb < 0)
                systime_adjust |= FM10K_SW_SYSTIME_ADJUST_DIR_NEGATIVE;

        fm10k_write_sw_reg(hw, FM10K_SW_SYSTIME_ADJUST, (u32)systime_adjust);

        return 0;
}

/**
 *  fm10k_read_systime_pf - Reads value of systime registers
 *  @hw: pointer to the hardware structure
 *
 *  Function reads the content of 2 registers, combined to represent a 64 bit
 *  value measured in nanosecods.  In order to guarantee the value is accurate
 *  we check the 32 most significant bits both before and after reading the
 *  32 least significant bits to verify they didn't change as we were reading
 *  the registers.
 **/
static u64 fm10k_read_systime_pf(struct fm10k_hw *hw)
{
        u32 systime_l, systime_h, systime_tmp;

        systime_h = fm10k_read_reg(hw, FM10K_SYSTIME + 1);

        do {
                systime_tmp = systime_h;
                systime_l = fm10k_read_reg(hw, FM10K_SYSTIME);
                systime_h = fm10k_read_reg(hw, FM10K_SYSTIME + 1);
        } while (systime_tmp != systime_h);

        return ((u64)systime_h << 32) | systime_l;
}

static const struct fm10k_msg_data fm10k_msg_data_pf[] = {
        FM10K_PF_MSG_ERR_HANDLER(XCAST_MODES, fm10k_msg_err_pf),
        FM10K_PF_MSG_ERR_HANDLER(UPDATE_MAC_FWD_RULE, fm10k_msg_err_pf),
        FM10K_PF_MSG_LPORT_MAP_HANDLER(fm10k_msg_lport_map_pf),
        FM10K_PF_MSG_ERR_HANDLER(LPORT_CREATE, fm10k_msg_err_pf),
        FM10K_PF_MSG_ERR_HANDLER(LPORT_DELETE, fm10k_msg_err_pf),
        FM10K_PF_MSG_UPDATE_PVID_HANDLER(fm10k_msg_update_pvid_pf),
        FM10K_TLV_MSG_ERROR_HANDLER(fm10k_tlv_msg_error),
};

static struct fm10k_mac_ops mac_ops_pf = {
        .get_bus_info           = &fm10k_get_bus_info_generic,
        .reset_hw               = &fm10k_reset_hw_pf,
        .init_hw                = &fm10k_init_hw_pf,
        .start_hw               = &fm10k_start_hw_generic,
        .stop_hw                = &fm10k_stop_hw_generic,
        .is_slot_appropriate    = &fm10k_is_slot_appropriate_pf,
        .update_vlan            = &fm10k_update_vlan_pf,
        .read_mac_addr          = &fm10k_read_mac_addr_pf,
        .update_uc_addr         = &fm10k_update_uc_addr_pf,
        .update_mc_addr         = &fm10k_update_mc_addr_pf,
        .update_xcast_mode      = &fm10k_update_xcast_mode_pf,
        .update_int_moderator   = &fm10k_update_int_moderator_pf,
        .update_lport_state     = &fm10k_update_lport_state_pf,
        .update_hw_stats        = &fm10k_update_hw_stats_pf,
        .rebind_hw_stats        = &fm10k_rebind_hw_stats_pf,
        .configure_dglort_map   = &fm10k_configure_dglort_map_pf,
        .set_dma_mask           = &fm10k_set_dma_mask_pf,
        .get_fault              = &fm10k_get_fault_pf,
        .get_host_state         = &fm10k_get_host_state_pf,
        .adjust_systime         = &fm10k_adjust_systime_pf,
        .read_systime           = &fm10k_read_systime_pf,
};

static struct fm10k_iov_ops iov_ops_pf = {
        .assign_resources               = &fm10k_iov_assign_resources_pf,
        .configure_tc                   = &fm10k_iov_configure_tc_pf,
        .assign_int_moderator           = &fm10k_iov_assign_int_moderator_pf,
        .assign_default_mac_vlan        = fm10k_iov_assign_default_mac_vlan_pf,
        .reset_resources                = &fm10k_iov_reset_resources_pf,
        .set_lport                      = &fm10k_iov_set_lport_pf,
        .reset_lport                    = &fm10k_iov_reset_lport_pf,
        .update_stats                   = &fm10k_iov_update_stats_pf,
        .report_timestamp               = &fm10k_iov_report_timestamp_pf,
};

static s32 fm10k_get_invariants_pf(struct fm10k_hw *hw)
{
        fm10k_get_invariants_generic(hw);

        return fm10k_sm_mbx_init(hw, &hw->mbx, fm10k_msg_data_pf);
}

struct fm10k_info fm10k_pf_info = {
        .mac            = fm10k_mac_pf,
        .get_invariants = &fm10k_get_invariants_pf,
        .mac_ops        = &mac_ops_pf,
        .iov_ops        = &iov_ops_pf,
};