/*
 * SuperH on-chip serial module support.  (SCI with no FIFO / with FIFO)
 *
 *  Copyright (C) 2002 - 2011  Paul Mundt
 *  Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
 *
 * based off of the old drivers/char/sh-sci.c by:
 *
 *   Copyright (C) 1999, 2000  Niibe Yutaka
 *   Copyright (C) 2000  Sugioka Toshinobu
 *   Modified to support multiple serial ports. Stuart Menefy (May 2000).
 *   Modified to support SecureEdge. David McCullough (2002)
 *   Modified to support SH7300 SCIF. Takashi Kusuda (Jun 2003).
 *   Removed SH7300 support (Jul 2007).
 *
 * This file is subject to the terms and conditions of the GNU General Public
 * License.  See the file "COPYING" in the main directory of this archive
 * for more details.
 */
#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif

#undef DEBUG

#include <linux/clk.h>
#include <linux/console.h>
#include <linux/ctype.h>
#include <linux/cpufreq.h>
#include <linux/delay.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/major.h>
#include <linux/module.h>
#include <linux/mm.h>
#include <linux/notifier.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/scatterlist.h>
#include <linux/serial.h>
#include <linux/serial_sci.h>
#include <linux/sh_dma.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/sysrq.h>
#include <linux/timer.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>

#ifdef CONFIG_SUPERH
#include <asm/sh_bios.h>
#endif

#include "sh-sci.h"

/* Offsets into the sci_port->irqs array */
enum {
        SCIx_ERI_IRQ,
        SCIx_RXI_IRQ,
        SCIx_TXI_IRQ,
        SCIx_BRI_IRQ,
        SCIx_NR_IRQS,

        SCIx_MUX_IRQ = SCIx_NR_IRQS,    /* special case */
};

#define SCIx_IRQ_IS_MUXED(port)                 \
        ((port)->irqs[SCIx_ERI_IRQ] ==  \
         (port)->irqs[SCIx_RXI_IRQ]) || \
        ((port)->irqs[SCIx_ERI_IRQ] &&  \
         ((port)->irqs[SCIx_RXI_IRQ] < 0))

struct sci_port {
        struct uart_port        port;

        /* Platform configuration */
        struct plat_sci_port    *cfg;
        int                     overrun_bit;
        unsigned int            error_mask;
        unsigned int            sampling_rate;


        /* Break timer */
        struct timer_list       break_timer;
        int                     break_flag;

        /* Interface clock */
        struct clk              *iclk;
        /* Function clock */
        struct clk              *fclk;

        int                     irqs[SCIx_NR_IRQS];
        char                    *irqstr[SCIx_NR_IRQS];

        struct dma_chan                 *chan_tx;
        struct dma_chan                 *chan_rx;

#ifdef CONFIG_SERIAL_SH_SCI_DMA
        struct dma_async_tx_descriptor  *desc_tx;
        struct dma_async_tx_descriptor  *desc_rx[2];
        dma_cookie_t                    cookie_tx;
        dma_cookie_t                    cookie_rx[2];
        dma_cookie_t                    active_rx;
        struct scatterlist              sg_tx;
        unsigned int                    sg_len_tx;
        struct scatterlist              sg_rx[2];
        size_t                          buf_len_rx;
        struct sh_dmae_slave            param_tx;
        struct sh_dmae_slave            param_rx;
        struct work_struct              work_tx;
        struct work_struct              work_rx;
        struct timer_list               rx_timer;
        unsigned int                    rx_timeout;
#endif

        struct notifier_block           freq_transition;
};

/* Function prototypes */
static void sci_start_tx(struct uart_port *port);
static void sci_stop_tx(struct uart_port *port);
static void sci_start_rx(struct uart_port *port);

#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS

static struct sci_port sci_ports[SCI_NPORTS];
static struct uart_driver sci_uart_driver;

static inline struct sci_port *
to_sci_port(struct uart_port *uart)
{
        return container_of(uart, struct sci_port, port);
}

struct plat_sci_reg {
        u8 offset, size;
};

/* Helper for invalidating specific entries of an inherited map. */
#define sci_reg_invalid { .offset = 0, .size = 0 }

static struct plat_sci_reg sci_regmap[SCIx_NR_REGTYPES][SCIx_NR_REGS] = {
        [SCIx_PROBE_REGTYPE] = {
                [0 ... SCIx_NR_REGS - 1] = sci_reg_invalid,
        },

        /*
         * Common SCI definitions, dependent on the port's regshift
         * value.
         */
        [SCIx_SCI_REGTYPE] = {
                [SCSMR]         = { 0x00,  8 },
                [SCBRR]         = { 0x01,  8 },
                [SCSCR]         = { 0x02,  8 },
                [SCxTDR]        = { 0x03,  8 },
                [SCxSR]         = { 0x04,  8 },
                [SCxRDR]        = { 0x05,  8 },
                [SCFCR]         = sci_reg_invalid,
                [SCFDR]         = sci_reg_invalid,
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common definitions for legacy IrDA ports, dependent on
         * regshift value.
         */
        [SCIx_IRDA_REGTYPE] = {
                [SCSMR]         = { 0x00,  8 },
                [SCBRR]         = { 0x01,  8 },
                [SCSCR]         = { 0x02,  8 },
                [SCxTDR]        = { 0x03,  8 },
                [SCxSR]         = { 0x04,  8 },
                [SCxRDR]        = { 0x05,  8 },
                [SCFCR]         = { 0x06,  8 },
                [SCFDR]         = { 0x07, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SCIFA definitions.
         */
        [SCIx_SCIFA_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x20,  8 },
                [SCxSR]         = { 0x14, 16 },
                [SCxRDR]        = { 0x24,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SCIFB definitions.
         */
        [SCIx_SCIFB_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x40,  8 },
                [SCxSR]         = { 0x14, 16 },
                [SCxRDR]        = { 0x60,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = sci_reg_invalid,
                [SCTFDR]        = { 0x38, 16 },
                [SCRFDR]        = { 0x3c, 16 },
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SH-2(A) SCIF definitions for ports with FIFO data
         * count registers.
         */
        [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x0c,  8 },
                [SCxSR]         = { 0x10, 16 },
                [SCxRDR]        = { 0x14,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = { 0x20, 16 },
                [SCLSR]         = { 0x24, 16 },
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SH-3 SCIF definitions.
         */
        [SCIx_SH3_SCIF_REGTYPE] = {
                [SCSMR]         = { 0x00,  8 },
                [SCBRR]         = { 0x02,  8 },
                [SCSCR]         = { 0x04,  8 },
                [SCxTDR]        = { 0x06,  8 },
                [SCxSR]         = { 0x08, 16 },
                [SCxRDR]        = { 0x0a,  8 },
                [SCFCR]         = { 0x0c,  8 },
                [SCFDR]         = { 0x0e, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SH-4(A) SCIF(B) definitions.
         */
        [SCIx_SH4_SCIF_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x0c,  8 },
                [SCxSR]         = { 0x10, 16 },
                [SCxRDR]        = { 0x14,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = { 0x20, 16 },
                [SCLSR]         = { 0x24, 16 },
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common HSCIF definitions.
         */
        [SCIx_HSCIF_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x0c,  8 },
                [SCxSR]         = { 0x10, 16 },
                [SCxRDR]        = { 0x14,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = { 0x20, 16 },
                [SCLSR]         = { 0x24, 16 },
                [HSSRR]         = { 0x40, 16 },
        },

        /*
         * Common SH-4(A) SCIF(B) definitions for ports without an SCSPTR
         * register.
         */
        [SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x0c,  8 },
                [SCxSR]         = { 0x10, 16 },
                [SCxRDR]        = { 0x14,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = { 0x24, 16 },
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * Common SH-4(A) SCIF(B) definitions for ports with FIFO data
         * count registers.
         */
        [SCIx_SH4_SCIF_FIFODATA_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x0c,  8 },
                [SCxSR]         = { 0x10, 16 },
                [SCxRDR]        = { 0x14,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = { 0x1c, 16 }, /* aliased to SCFDR */
                [SCRFDR]        = { 0x20, 16 },
                [SCSPTR]        = { 0x24, 16 },
                [SCLSR]         = { 0x28, 16 },
                [HSSRR]         = sci_reg_invalid,
        },

        /*
         * SH7705-style SCIF(B) ports, lacking both SCSPTR and SCLSR
         * registers.
         */
        [SCIx_SH7705_SCIF_REGTYPE] = {
                [SCSMR]         = { 0x00, 16 },
                [SCBRR]         = { 0x04,  8 },
                [SCSCR]         = { 0x08, 16 },
                [SCxTDR]        = { 0x20,  8 },
                [SCxSR]         = { 0x14, 16 },
                [SCxRDR]        = { 0x24,  8 },
                [SCFCR]         = { 0x18, 16 },
                [SCFDR]         = { 0x1c, 16 },
                [SCTFDR]        = sci_reg_invalid,
                [SCRFDR]        = sci_reg_invalid,
                [SCSPTR]        = sci_reg_invalid,
                [SCLSR]         = sci_reg_invalid,
                [HSSRR]         = sci_reg_invalid,
        },
};

#define sci_getreg(up, offset)          (sci_regmap[to_sci_port(up)->cfg->regtype] + offset)

/*
 * The "offset" here is rather misleading, in that it refers to an enum
 * value relative to the port mapping rather than the fixed offset
 * itself, which needs to be manually retrieved from the platform's
 * register map for the given port.
 */
static unsigned int sci_serial_in(struct uart_port *p, int offset)
{
        struct plat_sci_reg *reg = sci_getreg(p, offset);

        if (reg->size == 8)
                return ioread8(p->membase + (reg->offset << p->regshift));
        else if (reg->size == 16)
                return ioread16(p->membase + (reg->offset << p->regshift));
        else
                WARN(1, "Invalid register access\n");

        return 0;
}

static void sci_serial_out(struct uart_port *p, int offset, int value)
{
        struct plat_sci_reg *reg = sci_getreg(p, offset);

        if (reg->size == 8)
                iowrite8(value, p->membase + (reg->offset << p->regshift));
        else if (reg->size == 16)
                iowrite16(value, p->membase + (reg->offset << p->regshift));
        else
                WARN(1, "Invalid register access\n");
}

static int sci_probe_regmap(struct plat_sci_port *cfg)
{
        switch (cfg->type) {
        case PORT_SCI:
                cfg->regtype = SCIx_SCI_REGTYPE;
                break;
        case PORT_IRDA:
                cfg->regtype = SCIx_IRDA_REGTYPE;
                break;
        case PORT_SCIFA:
                cfg->regtype = SCIx_SCIFA_REGTYPE;
                break;
        case PORT_SCIFB:
                cfg->regtype = SCIx_SCIFB_REGTYPE;
                break;
        case PORT_SCIF:
                /*
                 * The SH-4 is a bit of a misnomer here, although that's
                 * where this particular port layout originated. This
                 * configuration (or some slight variation thereof)
                 * remains the dominant model for all SCIFs.
                 */
                cfg->regtype = SCIx_SH4_SCIF_REGTYPE;
                break;
        case PORT_HSCIF:
                cfg->regtype = SCIx_HSCIF_REGTYPE;
                break;
        default:
                pr_err("Can't probe register map for given port\n");
                return -EINVAL;
        }

        return 0;
}

static void sci_port_enable(struct sci_port *sci_port)
{
        if (!sci_port->port.dev)
                return;

        pm_runtime_get_sync(sci_port->port.dev);

        clk_prepare_enable(sci_port->iclk);
        sci_port->port.uartclk = clk_get_rate(sci_port->iclk);
        clk_prepare_enable(sci_port->fclk);
}

static void sci_port_disable(struct sci_port *sci_port)
{
        if (!sci_port->port.dev)
                return;

        /* Cancel the break timer to ensure that the timer handler will not try
         * to access the hardware with clocks and power disabled. Reset the
         * break flag to make the break debouncing state machine ready for the
         * next break.
         */
        del_timer_sync(&sci_port->break_timer);
        sci_port->break_flag = 0;

        clk_disable_unprepare(sci_port->fclk);
        clk_disable_unprepare(sci_port->iclk);

        pm_runtime_put_sync(sci_port->port.dev);
}

#if defined(CONFIG_CONSOLE_POLL) || defined(CONFIG_SERIAL_SH_SCI_CONSOLE)

#ifdef CONFIG_CONSOLE_POLL
static int sci_poll_get_char(struct uart_port *port)
{
        unsigned short status;
        int c;

        do {
                status = serial_port_in(port, SCxSR);
                if (status & SCxSR_ERRORS(port)) {
                        serial_port_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
                        continue;
                }
                break;
        } while (1);

        if (!(status & SCxSR_RDxF(port)))
                return NO_POLL_CHAR;

        c = serial_port_in(port, SCxRDR);

        /* Dummy read */
        serial_port_in(port, SCxSR);
        serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));

        return c;
}
#endif

static void sci_poll_put_char(struct uart_port *port, unsigned char c)
{
        unsigned short status;

        do {
                status = serial_port_in(port, SCxSR);
        } while (!(status & SCxSR_TDxE(port)));

        serial_port_out(port, SCxTDR, c);
        serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
}
#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE */

static void sci_init_pins(struct uart_port *port, unsigned int cflag)
{
        struct sci_port *s = to_sci_port(port);
        struct plat_sci_reg *reg = sci_regmap[s->cfg->regtype] + SCSPTR;

        /*
         * Use port-specific handler if provided.
         */
        if (s->cfg->ops && s->cfg->ops->init_pins) {
                s->cfg->ops->init_pins(port, cflag);
                return;
        }

        /*
         * For the generic path SCSPTR is necessary. Bail out if that's
         * unavailable, too.
         */
        if (!reg->size)
                return;

        if ((s->cfg->capabilities & SCIx_HAVE_RTSCTS) &&
            ((!(cflag & CRTSCTS)))) {
                unsigned short status;

                status = serial_port_in(port, SCSPTR);
                status &= ~SCSPTR_CTSIO;
                status |= SCSPTR_RTSIO;
                serial_port_out(port, SCSPTR, status); /* Set RTS = 1 */
        }
}

static int sci_txfill(struct uart_port *port)
{
        struct plat_sci_reg *reg;

        reg = sci_getreg(port, SCTFDR);
        if (reg->size)
                return serial_port_in(port, SCTFDR) & ((port->fifosize << 1) - 1);

        reg = sci_getreg(port, SCFDR);
        if (reg->size)
                return serial_port_in(port, SCFDR) >> 8;

        return !(serial_port_in(port, SCxSR) & SCI_TDRE);
}

static int sci_txroom(struct uart_port *port)
{
        return port->fifosize - sci_txfill(port);
}

static int sci_rxfill(struct uart_port *port)
{
        struct plat_sci_reg *reg;

        reg = sci_getreg(port, SCRFDR);
        if (reg->size)
                return serial_port_in(port, SCRFDR) & ((port->fifosize << 1) - 1);

        reg = sci_getreg(port, SCFDR);
        if (reg->size)
                return serial_port_in(port, SCFDR) & ((port->fifosize << 1) - 1);

        return (serial_port_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
}

/*
 * SCI helper for checking the state of the muxed port/RXD pins.
 */
static inline int sci_rxd_in(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);

        if (s->cfg->port_reg <= 0)
                return 1;

        /* Cast for ARM damage */
        return !!__raw_readb((void __iomem *)(uintptr_t)s->cfg->port_reg);
}

/* ********************************************************************** *
 *                   the interrupt related routines                       *
 * ********************************************************************** */

static void sci_transmit_chars(struct uart_port *port)
{
        struct circ_buf *xmit = &port->state->xmit;
        unsigned int stopped = uart_tx_stopped(port);
        unsigned short status;
        unsigned short ctrl;
        int count;

        status = serial_port_in(port, SCxSR);
        if (!(status & SCxSR_TDxE(port))) {
                ctrl = serial_port_in(port, SCSCR);
                if (uart_circ_empty(xmit))
                        ctrl &= ~SCSCR_TIE;
                else
                        ctrl |= SCSCR_TIE;
                serial_port_out(port, SCSCR, ctrl);
                return;
        }

        count = sci_txroom(port);

        do {
                unsigned char c;

                if (port->x_char) {
                        c = port->x_char;
                        port->x_char = 0;
                } else if (!uart_circ_empty(xmit) && !stopped) {
                        c = xmit->buf[xmit->tail];
                        xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
                } else {
                        break;
                }

                serial_port_out(port, SCxTDR, c);

                port->icount.tx++;
        } while (--count > 0);

        serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));

        if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
                uart_write_wakeup(port);
        if (uart_circ_empty(xmit)) {
                sci_stop_tx(port);
        } else {
                ctrl = serial_port_in(port, SCSCR);

                if (port->type != PORT_SCI) {
                        serial_port_in(port, SCxSR); /* Dummy read */
                        serial_port_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
                }

                ctrl |= SCSCR_TIE;
                serial_port_out(port, SCSCR, ctrl);
        }
}

/* On SH3, SCIF may read end-of-break as a space->mark char */
#define STEPFN(c)  ({int __c = (c); (((__c-1)|(__c)) == -1); })

static void sci_receive_chars(struct uart_port *port)
{
        struct sci_port *sci_port = to_sci_port(port);
        struct tty_port *tport = &port->state->port;
        int i, count, copied = 0;
        unsigned short status;
        unsigned char flag;

        status = serial_port_in(port, SCxSR);
        if (!(status & SCxSR_RDxF(port)))
                return;

        while (1) {
                /* Don't copy more bytes than there is room for in the buffer */
                count = tty_buffer_request_room(tport, sci_rxfill(port));

                /* If for any reason we can't copy more data, we're done! */
                if (count == 0)
                        break;

                if (port->type == PORT_SCI) {
                        char c = serial_port_in(port, SCxRDR);
                        if (uart_handle_sysrq_char(port, c) ||
                            sci_port->break_flag)
                                count = 0;
                        else
                                tty_insert_flip_char(tport, c, TTY_NORMAL);
                } else {
                        for (i = 0; i < count; i++) {
                                char c = serial_port_in(port, SCxRDR);

                                status = serial_port_in(port, SCxSR);
#if defined(CONFIG_CPU_SH3)
                                /* Skip "chars" during break */
                                if (sci_port->break_flag) {
                                        if ((c == 0) &&
                                            (status & SCxSR_FER(port))) {
                                                count--; i--;
                                                continue;
                                        }

                                        /* Nonzero => end-of-break */
                                        dev_dbg(port->dev, "debounce<%02x>\n", c);
                                        sci_port->break_flag = 0;

                                        if (STEPFN(c)) {
                                                count--; i--;
                                                continue;
                                        }
                                }
#endif /* CONFIG_CPU_SH3 */
                                if (uart_handle_sysrq_char(port, c)) {
                                        count--; i--;
                                        continue;
                                }

                                /* Store data and status */
                                if (status & SCxSR_FER(port)) {
                                        flag = TTY_FRAME;
                                        port->icount.frame++;
                                        dev_notice(port->dev, "frame error\n");
                                } else if (status & SCxSR_PER(port)) {
                                        flag = TTY_PARITY;
                                        port->icount.parity++;
                                        dev_notice(port->dev, "parity error\n");
                                } else
                                        flag = TTY_NORMAL;

                                tty_insert_flip_char(tport, c, flag);
                        }
                }

                serial_port_in(port, SCxSR); /* dummy read */
                serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));

                copied += count;
                port->icount.rx += count;
        }

        if (copied) {
                /* Tell the rest of the system the news. New characters! */
                tty_flip_buffer_push(tport);
        } else {
                serial_port_in(port, SCxSR); /* dummy read */
                serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
        }
}

#define SCI_BREAK_JIFFIES (HZ/20)

/*
 * The sci generates interrupts during the break,
 * 1 per millisecond or so during the break period, for 9600 baud.
 * So dont bother disabling interrupts.
 * But dont want more than 1 break event.
 * Use a kernel timer to periodically poll the rx line until
 * the break is finished.
 */
static inline void sci_schedule_break_timer(struct sci_port *port)
{
        mod_timer(&port->break_timer, jiffies + SCI_BREAK_JIFFIES);
}

/* Ensure that two consecutive samples find the break over. */
static void sci_break_timer(unsigned long data)
{
        struct sci_port *port = (struct sci_port *)data;

        if (sci_rxd_in(&port->port) == 0) {
                port->break_flag = 1;
                sci_schedule_break_timer(port);
        } else if (port->break_flag == 1) {
                /* break is over. */
                port->break_flag = 2;
                sci_schedule_break_timer(port);
        } else
                port->break_flag = 0;
}

static int sci_handle_errors(struct uart_port *port)
{
        int copied = 0;
        unsigned short status = serial_port_in(port, SCxSR);
        struct tty_port *tport = &port->state->port;
        struct sci_port *s = to_sci_port(port);

        /* Handle overruns */
        if (status & (1 << s->overrun_bit)) {
                port->icount.overrun++;

                /* overrun error */
                if (tty_insert_flip_char(tport, 0, TTY_OVERRUN))
                        copied++;

                dev_notice(port->dev, "overrun error\n");
        }

        if (status & SCxSR_FER(port)) {
                if (sci_rxd_in(port) == 0) {
                        /* Notify of BREAK */
                        struct sci_port *sci_port = to_sci_port(port);

                        if (!sci_port->break_flag) {
                                port->icount.brk++;

                                sci_port->break_flag = 1;
                                sci_schedule_break_timer(sci_port);

                                /* Do sysrq handling. */
                                if (uart_handle_break(port))
                                        return 0;

                                dev_dbg(port->dev, "BREAK detected\n");

                                if (tty_insert_flip_char(tport, 0, TTY_BREAK))
                                        copied++;
                        }

                } else {
                        /* frame error */
                        port->icount.frame++;

                        if (tty_insert_flip_char(tport, 0, TTY_FRAME))
                                copied++;

                        dev_notice(port->dev, "frame error\n");
                }
        }

        if (status & SCxSR_PER(port)) {
                /* parity error */
                port->icount.parity++;

                if (tty_insert_flip_char(tport, 0, TTY_PARITY))
                        copied++;

                dev_notice(port->dev, "parity error\n");
        }

        if (copied)
                tty_flip_buffer_push(tport);

        return copied;
}

static int sci_handle_fifo_overrun(struct uart_port *port)
{
        struct tty_port *tport = &port->state->port;
        struct sci_port *s = to_sci_port(port);
        struct plat_sci_reg *reg;
        int copied = 0;

        reg = sci_getreg(port, SCLSR);
        if (!reg->size)
                return 0;

        if ((serial_port_in(port, SCLSR) & (1 << s->overrun_bit))) {
                serial_port_out(port, SCLSR, 0);

                port->icount.overrun++;

                tty_insert_flip_char(tport, 0, TTY_OVERRUN);
                tty_flip_buffer_push(tport);

                dev_notice(port->dev, "overrun error\n");
                copied++;
        }

        return copied;
}

static int sci_handle_breaks(struct uart_port *port)
{
        int copied = 0;
        unsigned short status = serial_port_in(port, SCxSR);
        struct tty_port *tport = &port->state->port;
        struct sci_port *s = to_sci_port(port);

        if (uart_handle_break(port))
                return 0;

        if (!s->break_flag && status & SCxSR_BRK(port)) {
#if defined(CONFIG_CPU_SH3)
                /* Debounce break */
                s->break_flag = 1;
#endif

                port->icount.brk++;

                /* Notify of BREAK */
                if (tty_insert_flip_char(tport, 0, TTY_BREAK))
                        copied++;

                dev_dbg(port->dev, "BREAK detected\n");
        }

        if (copied)
                tty_flip_buffer_push(tport);

        copied += sci_handle_fifo_overrun(port);

        return copied;
}

static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
{
#ifdef CONFIG_SERIAL_SH_SCI_DMA
        struct uart_port *port = ptr;
        struct sci_port *s = to_sci_port(port);

        if (s->chan_rx) {
                u16 scr = serial_port_in(port, SCSCR);
                u16 ssr = serial_port_in(port, SCxSR);

                /* Disable future Rx interrupts */
                if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
                        disable_irq_nosync(irq);
                        scr |= SCSCR_RDRQE;
                } else {
                        scr &= ~SCSCR_RIE;
                }
                serial_port_out(port, SCSCR, scr);
                /* Clear current interrupt */
                serial_port_out(port, SCxSR, ssr & ~(1 | SCxSR_RDxF(port)));
                dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u jiffies\n",
                        jiffies, s->rx_timeout);
                mod_timer(&s->rx_timer, jiffies + s->rx_timeout);

                return IRQ_HANDLED;
        }
#endif

        /* I think sci_receive_chars has to be called irrespective
         * of whether the I_IXOFF is set, otherwise, how is the interrupt
         * to be disabled?
         */
        sci_receive_chars(ptr);

        return IRQ_HANDLED;
}

static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
{
        struct uart_port *port = ptr;
        unsigned long flags;

        spin_lock_irqsave(&port->lock, flags);
        sci_transmit_chars(port);
        spin_unlock_irqrestore(&port->lock, flags);

        return IRQ_HANDLED;
}

static irqreturn_t sci_er_interrupt(int irq, void *ptr)
{
        struct uart_port *port = ptr;

        /* Handle errors */
        if (port->type == PORT_SCI) {
                if (sci_handle_errors(port)) {
                        /* discard character in rx buffer */
                        serial_port_in(port, SCxSR);
                        serial_port_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
                }
        } else {
                sci_handle_fifo_overrun(port);
                sci_rx_interrupt(irq, ptr);
        }

        serial_port_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));

        /* Kick the transmission */
        sci_tx_interrupt(irq, ptr);

        return IRQ_HANDLED;
}

static irqreturn_t sci_br_interrupt(int irq, void *ptr)
{
        struct uart_port *port = ptr;

        /* Handle BREAKs */
        sci_handle_breaks(port);
        serial_port_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));

        return IRQ_HANDLED;
}

static inline unsigned long port_rx_irq_mask(struct uart_port *port)
{
        /*
         * Not all ports (such as SCIFA) will support REIE. Rather than
         * special-casing the port type, we check the port initialization
         * IRQ enable mask to see whether the IRQ is desired at all. If
         * it's unset, it's logically inferred that there's no point in
         * testing for it.
         */
        return SCSCR_RIE | (to_sci_port(port)->cfg->scscr & SCSCR_REIE);
}

static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
{
        unsigned short ssr_status, scr_status, err_enabled;
        struct uart_port *port = ptr;

        struct sci_port *s = to_sci_port(port);
        irqreturn_t ret = IRQ_NONE;

        ssr_status = serial_port_in(port, SCxSR);
        scr_status = serial_port_in(port, SCSCR);
        err_enabled = scr_status & port_rx_irq_mask(port);

        /* Tx Interrupt */
        if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
            !s->chan_tx)
                ret = sci_tx_interrupt(irq, ptr);

        /*
         * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
         * DR flags
         */
        if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
            (scr_status & SCSCR_RIE))
                ret = sci_rx_interrupt(irq, ptr);

        /* Error Interrupt */
        if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
                ret = sci_er_interrupt(irq, ptr);

        /* Break Interrupt */
        if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
                ret = sci_br_interrupt(irq, ptr);

        return ret;
}

/*
 * Here we define a transition notifier so that we can update all of our
 * ports' baud rate when the peripheral clock changes.
 */
static int sci_notifier(struct notifier_block *self,
                        unsigned long phase, void *p)
{
        struct sci_port *sci_port;
        unsigned long flags;

        sci_port = container_of(self, struct sci_port, freq_transition);

        if (phase == CPUFREQ_POSTCHANGE) {
                struct uart_port *port = &sci_port->port;

                spin_lock_irqsave(&port->lock, flags);
                port->uartclk = clk_get_rate(sci_port->iclk);
                spin_unlock_irqrestore(&port->lock, flags);
        }

        return NOTIFY_OK;
}

static struct sci_irq_desc {
        const char      *desc;
        irq_handler_t   handler;
} sci_irq_desc[] = {
        /*
         * Split out handlers, the default case.
         */
        [SCIx_ERI_IRQ] = {
                .desc = "rx err",
                .handler = sci_er_interrupt,
        },

        [SCIx_RXI_IRQ] = {
                .desc = "rx full",
                .handler = sci_rx_interrupt,
        },

        [SCIx_TXI_IRQ] = {
                .desc = "tx empty",
                .handler = sci_tx_interrupt,
        },

        [SCIx_BRI_IRQ] = {
                .desc = "break",
                .handler = sci_br_interrupt,
        },

        /*
         * Special muxed handler.
         */
        [SCIx_MUX_IRQ] = {
                .desc = "mux",
                .handler = sci_mpxed_interrupt,
        },
};

static int sci_request_irq(struct sci_port *port)
{
        struct uart_port *up = &port->port;
        int i, j, ret = 0;

        for (i = j = 0; i < SCIx_NR_IRQS; i++, j++) {
                struct sci_irq_desc *desc;
                int irq;

                if (SCIx_IRQ_IS_MUXED(port)) {
                        i = SCIx_MUX_IRQ;
                        irq = up->irq;
                } else {
                        irq = port->irqs[i];

                        /*
                         * Certain port types won't support all of the
                         * available interrupt sources.
                         */
                        if (unlikely(irq < 0))
                                continue;
                }

                desc = sci_irq_desc + i;
                port->irqstr[j] = kasprintf(GFP_KERNEL, "%s:%s",
                                            dev_name(up->dev), desc->desc);
                if (!port->irqstr[j]) {
                        dev_err(up->dev, "Failed to allocate %s IRQ string\n",
                                desc->desc);
                        goto out_nomem;
                }

                ret = request_irq(irq, desc->handler, up->irqflags,
                                  port->irqstr[j], port);
                if (unlikely(ret)) {
                        dev_err(up->dev, "Can't allocate %s IRQ\n", desc->desc);
                        goto out_noirq;
                }
        }

        return 0;

out_noirq:
        while (--i >= 0)
                free_irq(port->irqs[i], port);

out_nomem:
        while (--j >= 0)
                kfree(port->irqstr[j]);

        return ret;
}

static void sci_free_irq(struct sci_port *port)
{
        int i;

        /*
         * Intentionally in reverse order so we iterate over the muxed
         * IRQ first.
         */
        for (i = 0; i < SCIx_NR_IRQS; i++) {
                int irq = port->irqs[i];

                /*
                 * Certain port types won't support all of the available
                 * interrupt sources.
                 */
                if (unlikely(irq < 0))
                        continue;

                free_irq(port->irqs[i], port);
                kfree(port->irqstr[i]);

                if (SCIx_IRQ_IS_MUXED(port)) {
                        /* If there's only one IRQ, we're done. */
                        return;
                }
        }
}

static unsigned int sci_tx_empty(struct uart_port *port)
{
        unsigned short status = serial_port_in(port, SCxSR);
        unsigned short in_tx_fifo = sci_txfill(port);

        return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
}

/*
 * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
 * CTS/RTS is supported in hardware by at least one port and controlled
 * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
 * handled via the ->init_pins() op, which is a bit of a one-way street,
 * lacking any ability to defer pin control -- this will later be
 * converted over to the GPIO framework).
 *
 * Other modes (such as loopback) are supported generically on certain
 * port types, but not others. For these it's sufficient to test for the
 * existence of the support register and simply ignore the port type.
 */
static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
        if (mctrl & TIOCM_LOOP) {
                struct plat_sci_reg *reg;

                /*
                 * Standard loopback mode for SCFCR ports.
                 */
                reg = sci_getreg(port, SCFCR);
                if (reg->size)
                        serial_port_out(port, SCFCR,
                                        serial_port_in(port, SCFCR) |
                                        SCFCR_LOOP);
        }
}

static unsigned int sci_get_mctrl(struct uart_port *port)
{
        /*
         * CTS/RTS is handled in hardware when supported, while nothing
         * else is wired up. Keep it simple and simply assert DSR/CAR.
         */
        return TIOCM_DSR | TIOCM_CAR;
}

#ifdef CONFIG_SERIAL_SH_SCI_DMA
static void sci_dma_tx_complete(void *arg)
{
        struct sci_port *s = arg;
        struct uart_port *port = &s->port;
        struct circ_buf *xmit = &port->state->xmit;
        unsigned long flags;

        dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);

        spin_lock_irqsave(&port->lock, flags);

        xmit->tail += sg_dma_len(&s->sg_tx);
        xmit->tail &= UART_XMIT_SIZE - 1;

        port->icount.tx += sg_dma_len(&s->sg_tx);

        async_tx_ack(s->desc_tx);
        s->desc_tx = NULL;

        if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
                uart_write_wakeup(port);

        if (!uart_circ_empty(xmit)) {
                s->cookie_tx = 0;
                schedule_work(&s->work_tx);
        } else {
                s->cookie_tx = -EINVAL;
                if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
                        u16 ctrl = serial_port_in(port, SCSCR);
                        serial_port_out(port, SCSCR, ctrl & ~SCSCR_TIE);
                }
        }

        spin_unlock_irqrestore(&port->lock, flags);
}

/* Locking: called with port lock held */
static int sci_dma_rx_push(struct sci_port *s, size_t count)
{
        struct uart_port *port = &s->port;
        struct tty_port *tport = &port->state->port;
        int i, active, room;

        room = tty_buffer_request_room(tport, count);

        if (s->active_rx == s->cookie_rx[0]) {
                active = 0;
        } else if (s->active_rx == s->cookie_rx[1]) {
                active = 1;
        } else {
                dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
                return 0;
        }

        if (room < count)
                dev_warn(port->dev, "Rx overrun: dropping %zu bytes\n",
                         count - room);
        if (!room)
                return room;

        for (i = 0; i < room; i++)
                tty_insert_flip_char(tport, ((u8 *)sg_virt(&s->sg_rx[active]))[i],
                                     TTY_NORMAL);

        port->icount.rx += room;

        return room;
}

static void sci_dma_rx_complete(void *arg)
{
        struct sci_port *s = arg;
        struct uart_port *port = &s->port;
        unsigned long flags;
        int count;

        dev_dbg(port->dev, "%s(%d) active #%d\n",
                __func__, port->line, s->active_rx);

        spin_lock_irqsave(&port->lock, flags);

        count = sci_dma_rx_push(s, s->buf_len_rx);

        mod_timer(&s->rx_timer, jiffies + s->rx_timeout);

        spin_unlock_irqrestore(&port->lock, flags);

        if (count)
                tty_flip_buffer_push(&port->state->port);

        schedule_work(&s->work_rx);
}

static void sci_rx_dma_release(struct sci_port *s, bool enable_pio)
{
        struct dma_chan *chan = s->chan_rx;
        struct uart_port *port = &s->port;

        s->chan_rx = NULL;
        s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
        dma_release_channel(chan);
        if (sg_dma_address(&s->sg_rx[0]))
                dma_free_coherent(port->dev, s->buf_len_rx * 2,
                                  sg_virt(&s->sg_rx[0]), sg_dma_address(&s->sg_rx[0]));
        if (enable_pio)
                sci_start_rx(port);
}

static void sci_tx_dma_release(struct sci_port *s, bool enable_pio)
{
        struct dma_chan *chan = s->chan_tx;
        struct uart_port *port = &s->port;

        s->chan_tx = NULL;
        s->cookie_tx = -EINVAL;
        dma_release_channel(chan);
        if (enable_pio)
                sci_start_tx(port);
}

static void sci_submit_rx(struct sci_port *s)
{
        struct dma_chan *chan = s->chan_rx;
        int i;

        for (i = 0; i < 2; i++) {
                struct scatterlist *sg = &s->sg_rx[i];
                struct dma_async_tx_descriptor *desc;

                desc = dmaengine_prep_slave_sg(chan,
                        sg, 1, DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);

                if (desc) {
                        s->desc_rx[i] = desc;
                        desc->callback = sci_dma_rx_complete;
                        desc->callback_param = s;
                        s->cookie_rx[i] = desc->tx_submit(desc);
                }

                if (!desc || s->cookie_rx[i] < 0) {
                        if (i) {
                                async_tx_ack(s->desc_rx[0]);
                                s->cookie_rx[0] = -EINVAL;
                        }
                        if (desc) {
                                async_tx_ack(desc);
                                s->cookie_rx[i] = -EINVAL;
                        }
                        dev_warn(s->port.dev,
                                 "failed to re-start DMA, using PIO\n");
                        sci_rx_dma_release(s, true);
                        return;
                }
                dev_dbg(s->port.dev, "%s(): cookie %d to #%d\n",
                        __func__, s->cookie_rx[i], i);
        }

        s->active_rx = s->cookie_rx[0];

        dma_async_issue_pending(chan);
}

static void work_fn_rx(struct work_struct *work)
{
        struct sci_port *s = container_of(work, struct sci_port, work_rx);
        struct uart_port *port = &s->port;
        struct dma_async_tx_descriptor *desc;
        int new;

        if (s->active_rx == s->cookie_rx[0]) {
                new = 0;
        } else if (s->active_rx == s->cookie_rx[1]) {
                new = 1;
        } else {
                dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
                return;
        }
        desc = s->desc_rx[new];

        if (dma_async_is_tx_complete(s->chan_rx, s->active_rx, NULL, NULL) !=
            DMA_COMPLETE) {
                /* Handle incomplete DMA receive */
                struct dma_chan *chan = s->chan_rx;
                struct shdma_desc *sh_desc = container_of(desc,
                                        struct shdma_desc, async_tx);
                unsigned long flags;
                int count;

                dmaengine_terminate_all(chan);
                dev_dbg(port->dev, "Read %zu bytes with cookie %d\n",
                        sh_desc->partial, sh_desc->cookie);

                spin_lock_irqsave(&port->lock, flags);
                count = sci_dma_rx_push(s, sh_desc->partial);
                spin_unlock_irqrestore(&port->lock, flags);

                if (count)
                        tty_flip_buffer_push(&port->state->port);

                sci_submit_rx(s);

                return;
        }

        s->cookie_rx[new] = desc->tx_submit(desc);
        if (s->cookie_rx[new] < 0) {
                dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
                sci_rx_dma_release(s, true);
                return;
        }

        s->active_rx = s->cookie_rx[!new];

        dev_dbg(port->dev, "%s: cookie %d #%d, new active #%d\n",
                __func__, s->cookie_rx[new], new, s->active_rx);
}

static void work_fn_tx(struct work_struct *work)
{
        struct sci_port *s = container_of(work, struct sci_port, work_tx);
        struct dma_async_tx_descriptor *desc;
        struct dma_chan *chan = s->chan_tx;
        struct uart_port *port = &s->port;
        struct circ_buf *xmit = &port->state->xmit;
        struct scatterlist *sg = &s->sg_tx;

        /*
         * DMA is idle now.
         * Port xmit buffer is already mapped, and it is one page... Just adjust
         * offsets and lengths. Since it is a circular buffer, we have to
         * transmit till the end, and then the rest. Take the port lock to get a
         * consistent xmit buffer state.
         */
        spin_lock_irq(&port->lock);
        sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
        sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) +
                sg->offset;
        sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE),
                CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE));
        spin_unlock_irq(&port->lock);

        BUG_ON(!sg_dma_len(sg));

        desc = dmaengine_prep_slave_sg(chan,
                        sg, s->sg_len_tx, DMA_MEM_TO_DEV,
                        DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
        if (!desc) {
                /* switch to PIO */
                sci_tx_dma_release(s, true);
                return;
        }

        dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE);

        spin_lock_irq(&port->lock);
        s->desc_tx = desc;
        desc->callback = sci_dma_tx_complete;
        desc->callback_param = s;
        spin_unlock_irq(&port->lock);
        s->cookie_tx = desc->tx_submit(desc);
        if (s->cookie_tx < 0) {
                dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
                /* switch to PIO */
                sci_tx_dma_release(s, true);
                return;
        }

        dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n",
                __func__, xmit->buf, xmit->tail, xmit->head, s->cookie_tx);

        dma_async_issue_pending(chan);
}
#endif

static void sci_start_tx(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);
        unsigned short ctrl;

#ifdef CONFIG_SERIAL_SH_SCI_DMA
        if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
                u16 new, scr = serial_port_in(port, SCSCR);
                if (s->chan_tx)
                        new = scr | SCSCR_TDRQE;
                else
                        new = scr & ~SCSCR_TDRQE;
                if (new != scr)
                        serial_port_out(port, SCSCR, new);
        }

        if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
            s->cookie_tx < 0) {
                s->cookie_tx = 0;
                schedule_work(&s->work_tx);
        }
#endif

        if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
                /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
                ctrl = serial_port_in(port, SCSCR);
                serial_port_out(port, SCSCR, ctrl | SCSCR_TIE);
        }
}

static void sci_stop_tx(struct uart_port *port)
{
        unsigned short ctrl;

        /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
        ctrl = serial_port_in(port, SCSCR);

        if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
                ctrl &= ~SCSCR_TDRQE;

        ctrl &= ~SCSCR_TIE;

        serial_port_out(port, SCSCR, ctrl);
}

static void sci_start_rx(struct uart_port *port)
{
        unsigned short ctrl;

        ctrl = serial_port_in(port, SCSCR) | port_rx_irq_mask(port);

        if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
                ctrl &= ~SCSCR_RDRQE;

        serial_port_out(port, SCSCR, ctrl);
}

static void sci_stop_rx(struct uart_port *port)
{
        unsigned short ctrl;

        ctrl = serial_port_in(port, SCSCR);

        if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
                ctrl &= ~SCSCR_RDRQE;

        ctrl &= ~port_rx_irq_mask(port);

        serial_port_out(port, SCSCR, ctrl);
}

static void sci_break_ctl(struct uart_port *port, int break_state)
{
        struct sci_port *s = to_sci_port(port);
        struct plat_sci_reg *reg = sci_regmap[s->cfg->regtype] + SCSPTR;
        unsigned short scscr, scsptr;

        /* check wheter the port has SCSPTR */
        if (!reg->size) {
                /*
                 * Not supported by hardware. Most parts couple break and rx
                 * interrupts together, with break detection always enabled.
                 */
                return;
        }

        scsptr = serial_port_in(port, SCSPTR);
        scscr = serial_port_in(port, SCSCR);

        if (break_state == -1) {
                scsptr = (scsptr | SCSPTR_SPB2IO) & ~SCSPTR_SPB2DT;
                scscr &= ~SCSCR_TE;
        } else {
                scsptr = (scsptr | SCSPTR_SPB2DT) & ~SCSPTR_SPB2IO;
                scscr |= SCSCR_TE;
        }

        serial_port_out(port, SCSPTR, scsptr);
        serial_port_out(port, SCSCR, scscr);
}

#ifdef CONFIG_SERIAL_SH_SCI_DMA
static bool filter(struct dma_chan *chan, void *slave)
{
        struct sh_dmae_slave *param = slave;

        dev_dbg(chan->device->dev, "%s: slave ID %d\n",
                __func__, param->shdma_slave.slave_id);

        chan->private = &param->shdma_slave;
        return true;
}

static void rx_timer_fn(unsigned long arg)
{
        struct sci_port *s = (struct sci_port *)arg;
        struct uart_port *port = &s->port;
        u16 scr = serial_port_in(port, SCSCR);

        if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
                scr &= ~SCSCR_RDRQE;
                enable_irq(s->irqs[SCIx_RXI_IRQ]);
        }
        serial_port_out(port, SCSCR, scr | SCSCR_RIE);
        dev_dbg(port->dev, "DMA Rx timed out\n");
        schedule_work(&s->work_rx);
}

static void sci_request_dma(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);
        struct sh_dmae_slave *param;
        struct dma_chan *chan;
        dma_cap_mask_t mask;
        int nent;

        dev_dbg(port->dev, "%s: port %d\n", __func__, port->line);

        if (s->cfg->dma_slave_tx <= 0 || s->cfg->dma_slave_rx <= 0)
                return;

        dma_cap_zero(mask);
        dma_cap_set(DMA_SLAVE, mask);

        param = &s->param_tx;

        /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_TX */
        param->shdma_slave.slave_id = s->cfg->dma_slave_tx;

        s->cookie_tx = -EINVAL;
        chan = dma_request_channel(mask, filter, param);
        dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
        if (chan) {
                s->chan_tx = chan;
                sg_init_table(&s->sg_tx, 1);
                /* UART circular tx buffer is an aligned page. */
                BUG_ON((uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
                sg_set_page(&s->sg_tx, virt_to_page(port->state->xmit.buf),
                            UART_XMIT_SIZE,
                            (uintptr_t)port->state->xmit.buf & ~PAGE_MASK);
                nent = dma_map_sg(port->dev, &s->sg_tx, 1, DMA_TO_DEVICE);
                if (!nent)
                        sci_tx_dma_release(s, false);
                else
                        dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n",
                                __func__,
                                sg_dma_len(&s->sg_tx), port->state->xmit.buf,
                                &sg_dma_address(&s->sg_tx));

                s->sg_len_tx = nent;

                INIT_WORK(&s->work_tx, work_fn_tx);
        }

        param = &s->param_rx;

        /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_RX */
        param->shdma_slave.slave_id = s->cfg->dma_slave_rx;

        chan = dma_request_channel(mask, filter, param);
        dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
        if (chan) {
                dma_addr_t dma[2];
                void *buf[2];
                int i;

                s->chan_rx = chan;

                s->buf_len_rx = 2 * max(16, (int)port->fifosize);
                buf[0] = dma_alloc_coherent(port->dev, s->buf_len_rx * 2,
                                            &dma[0], GFP_KERNEL);

                if (!buf[0]) {
                        dev_warn(port->dev,
                                 "failed to allocate dma buffer, using PIO\n");
                        sci_rx_dma_release(s, true);
                        return;
                }

                buf[1] = buf[0] + s->buf_len_rx;
                dma[1] = dma[0] + s->buf_len_rx;

                for (i = 0; i < 2; i++) {
                        struct scatterlist *sg = &s->sg_rx[i];

                        sg_init_table(sg, 1);
                        sg_set_page(sg, virt_to_page(buf[i]), s->buf_len_rx,
                                    (uintptr_t)buf[i] & ~PAGE_MASK);
                        sg_dma_address(sg) = dma[i];
                }

                INIT_WORK(&s->work_rx, work_fn_rx);
                setup_timer(&s->rx_timer, rx_timer_fn, (unsigned long)s);

                sci_submit_rx(s);
        }
}

static void sci_free_dma(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);

        if (s->chan_tx)
                sci_tx_dma_release(s, false);
        if (s->chan_rx)
                sci_rx_dma_release(s, false);
}
#else
static inline void sci_request_dma(struct uart_port *port)
{
}

static inline void sci_free_dma(struct uart_port *port)
{
}
#endif

static int sci_startup(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);
        unsigned long flags;
        int ret;

        dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);

        ret = sci_request_irq(s);
        if (unlikely(ret < 0))
                return ret;

        sci_request_dma(port);

        spin_lock_irqsave(&port->lock, flags);
        sci_start_tx(port);
        sci_start_rx(port);
        spin_unlock_irqrestore(&port->lock, flags);

        return 0;
}

static void sci_shutdown(struct uart_port *port)
{
        struct sci_port *s = to_sci_port(port);
        unsigned long flags;

        dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);

        spin_lock_irqsave(&port->lock, flags);
        sci_stop_rx(port);
        sci_stop_tx(port);
        spin_unlock_irqrestore(&port->lock, flags);

        sci_free_dma(port);
        sci_free_irq(s);
}

static unsigned int sci_scbrr_calc(struct sci_port *s, unsigned int bps,
                                   unsigned long freq)
{
        if (s->sampling_rate)
                return DIV_ROUND_CLOSEST(freq, s->sampling_rate * bps) - 1;

        /* Warn, but use a safe default */
        WARN_ON(1);

        return ((freq + 16 * bps) / (32 * bps) - 1);
}

/* calculate frame length from SMR */
static int sci_baud_calc_frame_len(unsigned int smr_val)
{
        int len = 10;

        if (smr_val & SCSMR_CHR)
                len--;
        if (smr_val & SCSMR_PE)
                len++;
        if (smr_val & SCSMR_STOP)
                len++;

        return len;
}


/* calculate sample rate, BRR, and clock select for HSCIF */
static void sci_baud_calc_hscif(unsigned int bps, unsigned long freq,
                                int *brr, unsigned int *srr,
                                unsigned int *cks, int frame_len)
{
        int sr, c, br, err, recv_margin;
        int min_err = 1000; /* 100% */
        int recv_max_margin = 0;

        /* Find the combination of sample rate and clock select with the
           smallest deviation from the desired baud rate. */
        for (sr = 8; sr <= 32; sr++) {
                for (c = 0; c <= 3; c++) {
                        /* integerized formulas from HSCIF documentation */
                        br = DIV_ROUND_CLOSEST(freq, (sr *
                                              (1 << (2 * c + 1)) * bps)) - 1;
                        br = clamp(br, 0, 255);
                        err = DIV_ROUND_CLOSEST(freq, ((br + 1) * bps * sr *
                                               (1 << (2 * c + 1)) / 1000)) -
                                               1000;
                        /* Calc recv margin
                         * M: Receive margin (%)
                         * N: Ratio of bit rate to clock (N = sampling rate)
                         * D: Clock duty (D = 0 to 1.0)
                         * L: Frame length (L = 9 to 12)
                         * F: Absolute value of clock frequency deviation
                         *
                         *  M = |(0.5 - 1 / 2 * N) - ((L - 0.5) * F) -
                         *      (|D - 0.5| / N * (1 + F))|
                         *  NOTE: Usually, treat D for 0.5, F is 0 by this
                         *        calculation.
                         */
                        recv_margin = abs((500 -
                                        DIV_ROUND_CLOSEST(1000, sr << 1)) / 10);
                        if (abs(min_err) > abs(err)) {
                                min_err = err;
                                recv_max_margin = recv_margin;
                        } else if ((min_err == err) &&
                                   (recv_margin > recv_max_margin))
                                recv_max_margin = recv_margin;
                        else
                                continue;

                        *brr = br;
                        *srr = sr - 1;
                        *cks = c;
                }
        }

        if (min_err == 1000) {
                WARN_ON(1);
                /* use defaults */
                *brr = 255;
                *srr = 15;
                *cks = 0;
        }
}

static void sci_reset(struct uart_port *port)
{
        struct plat_sci_reg *reg;
        unsigned int status;

        do {
                status = serial_port_in(port, SCxSR);
        } while (!(status & SCxSR_TEND(port)));

        serial_port_out(port, SCSCR, 0x00);     /* TE=0, RE=0, CKE1=0 */

        reg = sci_getreg(port, SCFCR);
        if (reg->size)
                serial_port_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
}

static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
                            struct ktermios *old)
{
        struct sci_port *s = to_sci_port(port);
        struct plat_sci_reg *reg;
        unsigned int baud, smr_val = 0, max_baud, cks = 0;
        int t = -1;
        unsigned int srr = 15;

        if ((termios->c_cflag & CSIZE) == CS7)
                smr_val |= SCSMR_CHR;
        if (termios->c_cflag & PARENB)
                smr_val |= SCSMR_PE;
        if (termios->c_cflag & PARODD)
                smr_val |= SCSMR_PE | SCSMR_ODD;
        if (termios->c_cflag & CSTOPB)
                smr_val |= SCSMR_STOP;

        /*
         * earlyprintk comes here early on with port->uartclk set to zero.
         * the clock framework is not up and running at this point so here
         * we assume that 115200 is the maximum baud rate. please note that
         * the baud rate is not programmed during earlyprintk - it is assumed
         * that the previous boot loader has enabled required clocks and
         * setup the baud rate generator hardware for us already.
         */
        max_baud = port->uartclk ? port->uartclk / 16 : 115200;

        baud = uart_get_baud_rate(port, termios, old, 0, max_baud);
        if (likely(baud && port->uartclk)) {
                if (s->cfg->type == PORT_HSCIF) {
                        int frame_len = sci_baud_calc_frame_len(smr_val);
                        sci_baud_calc_hscif(baud, port->uartclk, &t, &srr,
                                            &cks, frame_len);
                } else {
                        t = sci_scbrr_calc(s, baud, port->uartclk);
                        for (cks = 0; t >= 256 && cks <= 3; cks++)
                                t >>= 2;
                }
        }

        sci_port_enable(s);

        sci_reset(port);

        smr_val |= serial_port_in(port, SCSMR) & 3;

        uart_update_timeout(port, termios->c_cflag, baud);

        dev_dbg(port->dev, "%s: SMR %x, cks %x, t %x, SCSCR %x\n",
                __func__, smr_val, cks, t, s->cfg->scscr);

        if (t >= 0) {
                serial_port_out(port, SCSMR, (smr_val & ~SCSMR_CKS) | cks);
                serial_port_out(port, SCBRR, t);
                reg = sci_getreg(port, HSSRR);
                if (reg->size)
                        serial_port_out(port, HSSRR, srr | HSCIF_SRE);
                udelay((1000000+(baud-1)) / baud); /* Wait one bit interval */
        } else
                serial_port_out(port, SCSMR, smr_val);

        sci_init_pins(port, termios->c_cflag);

        reg = sci_getreg(port, SCFCR);
        if (reg->size) {
                unsigned short ctrl = serial_port_in(port, SCFCR);

                if (s->cfg->capabilities & SCIx_HAVE_RTSCTS) {
                        if (termios->c_cflag & CRTSCTS)
                                ctrl |= SCFCR_MCE;
                        else
                                ctrl &= ~SCFCR_MCE;
                }

                /*
                 * As we've done a sci_reset() above, ensure we don't
                 * interfere with the FIFOs while toggling MCE. As the
                 * reset values could still be set, simply mask them out.
                 */
                ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);

                serial_port_out(port, SCFCR, ctrl);
        }

        serial_port_out(port, SCSCR, s->cfg->scscr);

#ifdef CONFIG_SERIAL_SH_SCI_DMA
        /*
         * Calculate delay for 1.5 DMA buffers: see
         * drivers/serial/serial_core.c::uart_update_timeout(). With 10 bits
         * (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above function
         * calculates 1 jiffie for the data plus 5 jiffies for the "slop(e)."
         * Then below we calculate 3 jiffies (12ms) for 1.5 DMA buffers (3 FIFO
         * sizes), but it has been found out experimentally, that this is not
         * enough: the driver too often needlessly runs on a DMA timeout. 20ms
         * as a minimum seem to work perfectly.
         */
        if (s->chan_rx) {
                s->rx_timeout = (port->timeout - HZ / 50) * s->buf_len_rx * 3 /
                        port->fifosize / 2;
                dev_dbg(port->dev, "DMA Rx t-out %ums, tty t-out %u jiffies\n",
                        s->rx_timeout * 1000 / HZ, port->timeout);
                if (s->rx_timeout < msecs_to_jiffies(20))
                        s->rx_timeout = msecs_to_jiffies(20);
        }
#endif

        if ((termios->c_cflag & CREAD) != 0)
                sci_start_rx(port);

        sci_port_disable(s);
}

static void sci_pm(struct uart_port *port, unsigned int state,
                   unsigned int oldstate)
{
        struct sci_port *sci_port = to_sci_port(port);

        switch (state) {
        case UART_PM_STATE_OFF:
                sci_port_disable(sci_port);
                break;
        default:
                sci_port_enable(sci_port);
                break;
        }
}

static const char *sci_type(struct uart_port *port)
{
        switch (port->type) {

        case PORT_IRDA:
                return "irda";
        case PORT_SCI:
                return "sci";
        case PORT_SCIF:
                return "scif";
        case PORT_SCIFA:
                return "scifa";
        case PORT_SCIFB:
                return "scifb";
        case PORT_HSCIF:
                return "hscif";
        }

        return NULL;
}

static inline unsigned long sci_port_size(struct uart_port *port)
{
        /*
         * Pick an arbitrary size that encapsulates all of the base
         * registers by default. This can be optimized later, or derived
         * from platform resource data at such a time that ports begin to
         * behave more erratically.
         */
        if (port->type == PORT_HSCIF)
                return 96;
        else
                return 64;
}

static int sci_remap_port(struct uart_port *port)
{
        unsigned long size = sci_port_size(port);

        /*
         * Nothing to do if there's already an established membase.
         */
        if (port->membase)
                return 0;

        if (port->flags & UPF_IOREMAP) {
                port->membase = ioremap_nocache(port->mapbase, size);
                if (unlikely(!port->membase)) {
                        dev_err(port->dev, "can't remap port#%d\n", port->line);
                        return -ENXIO;
                }
        } else {
                /*
                 * For the simple (and majority of) cases where we don't
                 * need to do any remapping, just cast the cookie
                 * directly.
                 */
                port->membase = (void __iomem *)(uintptr_t)port->mapbase;
        }

        return 0;
}

static void sci_release_port(struct uart_port *port)
{
        if (port->flags & UPF_IOREMAP) {
                iounmap(port->membase);
                port->membase = NULL;
        }

        release_mem_region(port->mapbase, sci_port_size(port));
}

static int sci_request_port(struct uart_port *port)
{
        unsigned long size = sci_port_size(port);
        struct resource *res;
        int ret;

        res = request_mem_region(port->mapbase, size, dev_name(port->dev));
        if (unlikely(res == NULL))
                return -EBUSY;

        ret = sci_remap_port(port);
        if (unlikely(ret != 0)) {
                release_resource(res);
                return ret;
        }

        return 0;
}

static void sci_config_port(struct uart_port *port, int flags)
{
        if (flags & UART_CONFIG_TYPE) {
                struct sci_port *sport = to_sci_port(port);

                port->type = sport->cfg->type;
                sci_request_port(port);
        }
}

static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
{
        if (ser->baud_base < 2400)
                /* No paper tape reader for Mitch.. */
                return -EINVAL;

        return 0;
}

static struct uart_ops sci_uart_ops = {
        .tx_empty       = sci_tx_empty,
        .set_mctrl      = sci_set_mctrl,
        .get_mctrl      = sci_get_mctrl,
        .start_tx       = sci_start_tx,
        .stop_tx        = sci_stop_tx,
        .stop_rx        = sci_stop_rx,
        .break_ctl      = sci_break_ctl,
        .startup        = sci_startup,
        .shutdown       = sci_shutdown,
        .set_termios    = sci_set_termios,
        .pm             = sci_pm,
        .type           = sci_type,
        .release_port   = sci_release_port,
        .request_port   = sci_request_port,
        .config_port    = sci_config_port,
        .verify_port    = sci_verify_port,
#ifdef CONFIG_CONSOLE_POLL
        .poll_get_char  = sci_poll_get_char,
        .poll_put_char  = sci_poll_put_char,
#endif
};

static int sci_init_single(struct platform_device *dev,
                           struct sci_port *sci_port, unsigned int index,
                           struct plat_sci_port *p, bool early)
{
        struct uart_port *port = &sci_port->port;
        const struct resource *res;
        unsigned int sampling_rate;
        unsigned int i;
        int ret;

        sci_port->cfg   = p;

        port->ops       = &sci_uart_ops;
        port->iotype    = UPIO_MEM;
        port->line      = index;

        res = platform_get_resource(dev, IORESOURCE_MEM, 0);
        if (res == NULL)
                return -ENOMEM;

        port->mapbase = res->start;

        for (i = 0; i < ARRAY_SIZE(sci_port->irqs); ++i)
                sci_port->irqs[i] = platform_get_irq(dev, i);

        /* The SCI generates several interrupts. They can be muxed together or
         * connected to different interrupt lines. In the muxed case only one
         * interrupt resource is specified. In the non-muxed case three or four
         * interrupt resources are specified, as the BRI interrupt is optional.
         */
        if (sci_port->irqs[0] < 0)
                return -ENXIO;

        if (sci_port->irqs[1] < 0) {
                sci_port->irqs[1] = sci_port->irqs[0];
                sci_port->irqs[2] = sci_port->irqs[0];
                sci_port->irqs[3] = sci_port->irqs[0];
        }

        if (p->regtype == SCIx_PROBE_REGTYPE) {
                ret = sci_probe_regmap(p);
                if (unlikely(ret))
                        return ret;
        }

        switch (p->type) {
        case PORT_SCIFB:
                port->fifosize = 256;
                sci_port->overrun_bit = 9;
                sampling_rate = 16;
                break;
        case PORT_HSCIF:
                port->fifosize = 128;
                sampling_rate = 0;
                sci_port->overrun_bit = 0;
                break;
        case PORT_SCIFA:
                port->fifosize = 64;
                sci_port->overrun_bit = 9;
                sampling_rate = 16;
                break;
        case PORT_SCIF:
                port->fifosize = 16;
                if (p->regtype == SCIx_SH7705_SCIF_REGTYPE) {
                        sci_port->overrun_bit = 9;
                        sampling_rate = 16;
                } else {
                        sci_port->overrun_bit = 0;
                        sampling_rate = 32;
                }
                break;
        default:
                port->fifosize = 1;
                sci_port->overrun_bit = 5;
                sampling_rate = 32;
                break;
        }

        /* SCIFA on sh7723 and sh7724 need a custom sampling rate that doesn't
         * match the SoC datasheet, this should be investigated. Let platform
         * data override the sampling rate for now.
         */
        sci_port->sampling_rate = p->sampling_rate ? p->sampling_rate
                                : sampling_rate;

        if (!early) {
                sci_port->iclk = clk_get(&dev->dev, "sci_ick");
                if (IS_ERR(sci_port->iclk)) {
                        sci_port->iclk = clk_get(&dev->dev, "peripheral_clk");
                        if (IS_ERR(sci_port->iclk)) {
                                dev_err(&dev->dev, "can't get iclk\n");
                                return PTR_ERR(sci_port->iclk);
                        }
                }

                /*
                 * The function clock is optional, ignore it if we can't
                 * find it.
                 */
                sci_port->fclk = clk_get(&dev->dev, "sci_fck");
                if (IS_ERR(sci_port->fclk))
                        sci_port->fclk = NULL;

                port->dev = &dev->dev;

                pm_runtime_enable(&dev->dev);
        }

        sci_port->break_timer.data = (unsigned long)sci_port;
        sci_port->break_timer.function = sci_break_timer;
        init_timer(&sci_port->break_timer);

        /*
         * Establish some sensible defaults for the error detection.
         */
        sci_port->error_mask = (p->type == PORT_SCI) ?
                        SCI_DEFAULT_ERROR_MASK : SCIF_DEFAULT_ERROR_MASK;

        /*
         * Establish sensible defaults for the overrun detection, unless
         * the part has explicitly disabled support for it.
         */

        /*
         * Make the error mask inclusive of overrun detection, if
         * supported.
         */
        sci_port->error_mask |= 1 << sci_port->overrun_bit;

        port->type              = p->type;
        port->flags             = UPF_FIXED_PORT | p->flags;
        port->regshift          = p->regshift;

        /*
         * The UART port needs an IRQ value, so we peg this to the RX IRQ
         * for the multi-IRQ ports, which is where we are primarily
         * concerned with the shutdown path synchronization.
         *
         * For the muxed case there's nothing more to do.
         */
        port->irq               = sci_port->irqs[SCIx_RXI_IRQ];
        port->irqflags          = 0;

        port->serial_in         = sci_serial_in;
        port->serial_out        = sci_serial_out;

        if (p->dma_slave_tx > 0 && p->dma_slave_rx > 0)
                dev_dbg(port->dev, "DMA tx %d, rx %d\n",
                        p->dma_slave_tx, p->dma_slave_rx);

        return 0;
}

static void sci_cleanup_single(struct sci_port *port)
{
        clk_put(port->iclk);
        clk_put(port->fclk);

        pm_runtime_disable(port->port.dev);
}

#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
static void serial_console_putchar(struct uart_port *port, int ch)
{
        sci_poll_put_char(port, ch);
}

/*
 *      Print a string to the serial port trying not to disturb
 *      any possible real use of the port...
 */
static void serial_console_write(struct console *co, const char *s,
                                 unsigned count)
{
        struct sci_port *sci_port = &sci_ports[co->index];
        struct uart_port *port = &sci_port->port;
        unsigned short bits, ctrl;
        unsigned long flags;
        int locked = 1;

        local_irq_save(flags);
        if (port->sysrq)
                locked = 0;
        else if (oops_in_progress)
                locked = spin_trylock(&port->lock);
        else
                spin_lock(&port->lock);

        /* first save the SCSCR then disable the interrupts */
        ctrl = serial_port_in(port, SCSCR);
        serial_port_out(port, SCSCR, sci_port->cfg->scscr);

        uart_console_write(port, s, count, serial_console_putchar);

        /* wait until fifo is empty and last bit has been transmitted */
        bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
        while ((serial_port_in(port, SCxSR) & bits) != bits)
                cpu_relax();

        /* restore the SCSCR */
        serial_port_out(port, SCSCR, ctrl);

        if (locked)
                spin_unlock(&port->lock);
        local_irq_restore(flags);
}

static int serial_console_setup(struct console *co, char *options)
{
        struct sci_port *sci_port;
        struct uart_port *port;
        int baud = 115200;
        int bits = 8;
        int parity = 'n';
        int flow = 'n';
        int ret;

        /*
         * Refuse to handle any bogus ports.
         */
        if (co->index < 0 || co->index >= SCI_NPORTS)
                return -ENODEV;

        sci_port = &sci_ports[co->index];
        port = &sci_port->port;

        /*
         * Refuse to handle uninitialized ports.
         */
        if (!port->ops)
                return -ENODEV;

        ret = sci_remap_port(port);
        if (unlikely(ret != 0))
                return ret;

        if (options)
                uart_parse_options(options, &baud, &parity, &bits, &flow);

        return uart_set_options(port, co, baud, parity, bits, flow);
}

static struct console serial_console = {
        .name           = "ttySC",
        .device         = uart_console_device,
        .write          = serial_console_write,
        .setup          = serial_console_setup,
        .flags          = CON_PRINTBUFFER,
        .index          = -1,
        .data           = &sci_uart_driver,
};

static struct console early_serial_console = {
        .name           = "early_ttySC",
        .write          = serial_console_write,
        .flags          = CON_PRINTBUFFER,
        .index          = -1,
};

static char early_serial_buf[32];

static int sci_probe_earlyprintk(struct platform_device *pdev)
{
        struct plat_sci_port *cfg = dev_get_platdata(&pdev->dev);

        if (early_serial_console.data)
                return -EEXIST;

        early_serial_console.index = pdev->id;

        sci_init_single(pdev, &sci_ports[pdev->id], pdev->id, cfg, true);

        serial_console_setup(&early_serial_console, early_serial_buf);

        if (!strstr(early_serial_buf, "keep"))
                early_serial_console.flags |= CON_BOOT;

        register_console(&early_serial_console);
        return 0;
}

#define SCI_CONSOLE     (&serial_console)

#else
static inline int sci_probe_earlyprintk(struct platform_device *pdev)
{
        return -EINVAL;
}

#define SCI_CONSOLE     NULL

#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */

static const char banner[] __initconst = "SuperH (H)SCI(F) driver initialized";

static struct uart_driver sci_uart_driver = {
        .owner          = THIS_MODULE,
        .driver_name    = "sci",
        .dev_name       = "ttySC",
        .major          = SCI_MAJOR,
        .minor          = SCI_MINOR_START,
        .nr             = SCI_NPORTS,
        .cons           = SCI_CONSOLE,
};

static int sci_remove(struct platform_device *dev)
{
        struct sci_port *port = platform_get_drvdata(dev);

        cpufreq_unregister_notifier(&port->freq_transition,
                                    CPUFREQ_TRANSITION_NOTIFIER);

        uart_remove_one_port(&sci_uart_driver, &port->port);

        sci_cleanup_single(port);

        return 0;
}

struct sci_port_info {
        unsigned int type;
        unsigned int regtype;
};

static const struct of_device_id of_sci_match[] = {
        {
                .compatible = "renesas,scif",
                .data = &(const struct sci_port_info) {
                        .type = PORT_SCIF,
                        .regtype = SCIx_SH4_SCIF_REGTYPE,
                },
        }, {
                .compatible = "renesas,scifa",
                .data = &(const struct sci_port_info) {
                        .type = PORT_SCIFA,
                        .regtype = SCIx_SCIFA_REGTYPE,
                },
        }, {
                .compatible = "renesas,scifb",
                .data = &(const struct sci_port_info) {
                        .type = PORT_SCIFB,
                        .regtype = SCIx_SCIFB_REGTYPE,
                },
        }, {
                .compatible = "renesas,hscif",
                .data = &(const struct sci_port_info) {
                        .type = PORT_HSCIF,
                        .regtype = SCIx_HSCIF_REGTYPE,
                },
        }, {
                /* Terminator */
        },
};
MODULE_DEVICE_TABLE(of, of_sci_match);

static struct plat_sci_port *
sci_parse_dt(struct platform_device *pdev, unsigned int *dev_id)
{
        struct device_node *np = pdev->dev.of_node;
        const struct of_device_id *match;
        const struct sci_port_info *info;
        struct plat_sci_port *p;
        int id;

        if (!IS_ENABLED(CONFIG_OF) || !np)
                return NULL;

        match = of_match_node(of_sci_match, pdev->dev.of_node);
        if (!match)
                return NULL;

        info = match->data;

        p = devm_kzalloc(&pdev->dev, sizeof(struct plat_sci_port), GFP_KERNEL);
        if (!p) {
                dev_err(&pdev->dev, "failed to allocate DT config data\n");
                return NULL;
        }

        /* Get the line number for the aliases node. */
        id = of_alias_get_id(np, "serial");
        if (id < 0) {
                dev_err(&pdev->dev, "failed to get alias id (%d)\n", id);
                return NULL;
        }

        *dev_id = id;

        p->flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
        p->type = info->type;
        p->regtype = info->regtype;
        p->scscr = SCSCR_RE | SCSCR_TE;

        return p;
}

static int sci_probe_single(struct platform_device *dev,
                                      unsigned int index,
                                      struct plat_sci_port *p,
                                      struct sci_port *sciport)
{
        int ret;

        /* Sanity check */
        if (unlikely(index >= SCI_NPORTS)) {
                dev_notice(&dev->dev, "Attempting to register port %d when only %d are available\n",
                           index+1, SCI_NPORTS);
                dev_notice(&dev->dev, "Consider bumping CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
                return -EINVAL;
        }

        ret = sci_init_single(dev, sciport, index, p, false);
        if (ret)
                return ret;

        ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
        if (ret) {
                sci_cleanup_single(sciport);
                return ret;
        }

        return 0;
}

static int sci_probe(struct platform_device *dev)
{
        struct plat_sci_port *p;
        struct sci_port *sp;
        unsigned int dev_id;
        int ret;

        /*
         * If we've come here via earlyprintk initialization, head off to
         * the special early probe. We don't have sufficient device state
         * to make it beyond this yet.
         */
        if (is_early_platform_device(dev))
                return sci_probe_earlyprintk(dev);

        if (dev->dev.of_node) {
                p = sci_parse_dt(dev, &dev_id);
                if (p == NULL)
                        return -EINVAL;
        } else {
                p = dev->dev.platform_data;
                if (p == NULL) {
                        dev_err(&dev->dev, "no platform data supplied\n");
                        return -EINVAL;
                }

                dev_id = dev->id;
        }

        sp = &sci_ports[dev_id];
        platform_set_drvdata(dev, sp);

        ret = sci_probe_single(dev, dev_id, p, sp);
        if (ret)
                return ret;

        sp->freq_transition.notifier_call = sci_notifier;

        ret = cpufreq_register_notifier(&sp->freq_transition,
                                        CPUFREQ_TRANSITION_NOTIFIER);
        if (unlikely(ret < 0)) {
                uart_remove_one_port(&sci_uart_driver, &sp->port);
                sci_cleanup_single(sp);
                return ret;
        }

#ifdef CONFIG_SH_STANDARD_BIOS
        sh_bios_gdb_detach();
#endif

        return 0;
}

static int sci_suspend(struct device *dev)
{
        struct sci_port *sport = dev_get_drvdata(dev);

        if (sport)
                uart_suspend_port(&sci_uart_driver, &sport->port);

        return 0;
}

static int sci_resume(struct device *dev)
{
        struct sci_port *sport = dev_get_drvdata(dev);

        if (sport)
                uart_resume_port(&sci_uart_driver, &sport->port);

        return 0;
}

static const struct dev_pm_ops sci_dev_pm_ops = {
        .suspend        = sci_suspend,
        .resume         = sci_resume,
};

static struct platform_driver sci_driver = {
        .probe          = sci_probe,
        .remove         = sci_remove,
        .driver         = {
                .name   = "sh-sci",
                .pm     = &sci_dev_pm_ops,
                .of_match_table = of_match_ptr(of_sci_match),
        },
};

static int __init sci_init(void)
{
        int ret;

        pr_info("%s\n", banner);

        ret = uart_register_driver(&sci_uart_driver);
        if (likely(ret == 0)) {
                ret = platform_driver_register(&sci_driver);
                if (unlikely(ret))
                        uart_unregister_driver(&sci_uart_driver);
        }

        return ret;
}

static void __exit sci_exit(void)
{
        platform_driver_unregister(&sci_driver);
        uart_unregister_driver(&sci_uart_driver);
}

#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
early_platform_init_buffer("earlyprintk", &sci_driver,
                           early_serial_buf, ARRAY_SIZE(early_serial_buf));
#endif
module_init(sci_init);
module_exit(sci_exit);

MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:sh-sci");
MODULE_AUTHOR("Paul Mundt");
MODULE_DESCRIPTION("SuperH (H)SCI(F) serial driver");