LXR linux/drivers/ata/pata

   1/*
   2 * pata_serverworks.c   - Serverworks PATA for new ATA layer
   3 *                        (C) 2005 Red Hat Inc
   4 *                        (C) 2010 Bartlomiej Zolnierkiewicz
   5 *
   6 * based upon
   7 *
   8 * serverworks.c
   9 *
  10 * Copyright (C) 1998-2000 Michel Aubry
  11 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
  12 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
  13 * Portions copyright (c) 2001 Sun Microsystems
  14 *
  15 *
  16 * RCC/ServerWorks IDE driver for Linux
  17 *
  18 *   OSB4: `Open South Bridge' IDE Interface (fn 1)
  19 *         supports UDMA mode 2 (33 MB/s)
  20 *
  21 *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
  22 *         all revisions support UDMA mode 4 (66 MB/s)
  23 *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
  24 *
  25 *         *** The CSB5 does not provide ANY register ***
  26 *         *** to detect 80-conductor cable presence. ***
  27 *
  28 *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
  29 *
  30 * Documentation:
  31 *      Available under NDA only. Errata info very hard to get.
  32 */
  33
  34#include <linux/kernel.h>
  35#include <linux/module.h>
  36#include <linux/pci.h>
  37#include <linux/init.h>
  38#include <linux/blkdev.h>
  39#include <linux/delay.h>
  40#include <scsi/scsi_host.h>
  41#include <linux/libata.h>
  42
  43#define DRV_NAME "pata_serverworks"
  44#define DRV_VERSION "0.4.3"
  45
  46#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
  47#define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
  48
  49/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
  50 * can overrun their FIFOs when used with the CSB5 */
  51
  52static const char *csb_bad_ata100[] = {
  53        "ST320011A",
  54        "ST340016A",
  55        "ST360021A",
  56        "ST380021A",
  57        NULL
  58};
  59
  60/**
  61 *      oem_cable       -       Dell/Sun serverworks cable detection
  62 *      @ap: ATA port to do cable detect
  63 *
  64 *      Dell PowerEdge and Sun Cobalt 'Alpine' hide the 40/80 pin select
  65 *      for their interfaces in the top two bits of the subsystem ID.
  66 */
  67
  68static int oem_cable(struct ata_port *ap)
  69{
  70        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  71
  72        if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
  73                return ATA_CBL_PATA80;
  74        return ATA_CBL_PATA40;
  75}
  76
  77struct sv_cable_table {
  78        int device;
  79        int subvendor;
  80        int (*cable_detect)(struct ata_port *ap);
  81};
  82
  83static struct sv_cable_table cable_detect[] = {
  84        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_VENDOR_ID_DELL, oem_cable },
  85        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE,   PCI_VENDOR_ID_DELL, oem_cable },
  86        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_VENDOR_ID_SUN,  oem_cable },
  87        { PCI_DEVICE_ID_SERVERWORKS_OSB4IDE,   PCI_ANY_ID, ata_cable_40wire  },
  88        { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_ANY_ID, ata_cable_unknown },
  89        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE,   PCI_ANY_ID, ata_cable_unknown },
  90        { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2,  PCI_ANY_ID, ata_cable_unknown },
  91        { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, ata_cable_unknown },
  92        { }
  93};
  94
  95/**
  96 *      serverworks_cable_detect        -       cable detection
  97 *      @ap: ATA port
  98 *
  99 *      Perform cable detection according to the device and subvendor
 100 *      identifications
 101 */
 102
 103static int serverworks_cable_detect(struct ata_port *ap)
 104{
 105        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 106        struct sv_cable_table *cb = cable_detect;
 107
 108        while(cb->device) {
 109                if (cb->device == pdev->device &&
 110                    (cb->subvendor == pdev->subsystem_vendor ||
 111                      cb->subvendor == PCI_ANY_ID)) {
 112                        return cb->cable_detect(ap);
 113                }
 114                cb++;
 115        }
 116
 117        BUG();
 118        return -1;      /* kill compiler warning */
 119}
 120
 121/**
 122 *      serverworks_is_csb      -       Check for CSB or OSB
 123 *      @pdev: PCI device to check
 124 *
 125 *      Returns true if the device being checked is known to be a CSB
 126 *      series device.
 127 */
 128
 129static u8 serverworks_is_csb(struct pci_dev *pdev)
 130{
 131        switch (pdev->device) {
 132                case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 133                case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 134                case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 135                case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 136                        return 1;
 137                default:
 138                        break;
 139        }
 140        return 0;
 141}
 142
 143/**
 144 *      serverworks_osb4_filter -       mode selection filter
 145 *      @adev: ATA device
 146 *      @mask: Mask of proposed modes
 147 *
 148 *      Filter the offered modes for the device to apply controller
 149 *      specific rules. OSB4 requires no UDMA for disks due to a FIFO
 150 *      bug we hit.
 151 */
 152
 153static unsigned long serverworks_osb4_filter(struct ata_device *adev, unsigned long mask)
 154{
 155        if (adev->class == ATA_DEV_ATA)
 156                mask &= ~ATA_MASK_UDMA;
 157        return mask;
 158}
 159
 160
 161/**
 162 *      serverworks_csb_filter  -       mode selection filter
 163 *      @adev: ATA device
 164 *      @mask: Mask of proposed modes
 165 *
 166 *      Check the blacklist and disable UDMA5 if matched
 167 */
 168
 169static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned long mask)
 170{
 171        const char *p;
 172        char model_num[ATA_ID_PROD_LEN + 1];
 173        int i;
 174
 175        /* Disk, UDMA */
 176        if (adev->class != ATA_DEV_ATA)
 177                return mask;
 178
 179        /* Actually do need to check */
 180        ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num));
 181
 182        for (i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
 183                if (!strcmp(p, model_num))
 184                        mask &= ~(0xE0 << ATA_SHIFT_UDMA);
 185        }
 186        return mask;
 187}
 188
 189/**
 190 *      serverworks_set_piomode -       set initial PIO mode data
 191 *      @ap: ATA interface
 192 *      @adev: ATA device
 193 *
 194 *      Program the OSB4/CSB5 timing registers for PIO. The PIO register
 195 *      load is done as a simple lookup.
 196 */
 197static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
 198{
 199        static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 200        int offset = 1 + 2 * ap->port_no - adev->devno;
 201        int devbits = (2 * ap->port_no + adev->devno) * 4;
 202        u16 csb5_pio;
 203        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 204        int pio = adev->pio_mode - XFER_PIO_0;
 205
 206        pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);
 207
 208        /* The OSB4 just requires the timing but the CSB series want the
 209           mode number as well */
 210        if (serverworks_is_csb(pdev)) {
 211                pci_read_config_word(pdev, 0x4A, &csb5_pio);
 212                csb5_pio &= ~(0x0F << devbits);
 213                pci_write_config_word(pdev, 0x4A, csb5_pio | (pio << devbits));
 214        }
 215}
 216
 217/**
 218 *      serverworks_set_dmamode -       set initial DMA mode data
 219 *      @ap: ATA interface
 220 *      @adev: ATA device
 221 *
 222 *      Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
 223 *      chipset. The MWDMA mode values are pulled from a lookup table
 224 *      while the chipset uses mode number for UDMA.
 225 */
 226
 227static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 228{
 229        static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
 230        int offset = 1 + 2 * ap->port_no - adev->devno;
 231        int devbits = 2 * ap->port_no + adev->devno;
 232        u8 ultra;
 233        u8 ultra_cfg;
 234        struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 235
 236        pci_read_config_byte(pdev, 0x54, &ultra_cfg);
 237        pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
 238        ultra &= ~(0x0F << (adev->devno * 4));
 239
 240        if (adev->dma_mode >= XFER_UDMA_0) {
 241                pci_write_config_byte(pdev, 0x44 + offset,  0x20);
 242
 243                ultra |= (adev->dma_mode - XFER_UDMA_0)
 244                                        << (adev->devno * 4);
 245                ultra_cfg |=  (1 << devbits);
 246        } else {
 247                pci_write_config_byte(pdev, 0x44 + offset,
 248                        dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
 249                ultra_cfg &= ~(1 << devbits);
 250        }
 251        pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
 252        pci_write_config_byte(pdev, 0x54, ultra_cfg);
 253}
 254
 255static struct scsi_host_template serverworks_sht = {
 256        ATA_BMDMA_SHT(DRV_NAME),
 257};
 258
 259static struct ata_port_operations serverworks_osb4_port_ops = {
 260        .inherits       = &ata_bmdma_port_ops,
 261        .cable_detect   = serverworks_cable_detect,
 262        .mode_filter    = serverworks_osb4_filter,
 263        .set_piomode    = serverworks_set_piomode,
 264        .set_dmamode    = serverworks_set_dmamode,
 265};
 266
 267static struct ata_port_operations serverworks_csb_port_ops = {
 268        .inherits       = &serverworks_osb4_port_ops,
 269        .mode_filter    = serverworks_csb_filter,
 270};
 271
 272static int serverworks_fixup_osb4(struct pci_dev *pdev)
 273{
 274        u32 reg;
 275        struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 276                  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 277        if (isa_dev) {
 278                pci_read_config_dword(isa_dev, 0x64, &reg);
 279                reg &= ~0x00002000; /* disable 600ns interrupt mask */
 280                if (!(reg & 0x00004000))
 281                        printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
 282                reg |=  0x00004000; /* enable UDMA/33 support */
 283                pci_write_config_dword(isa_dev, 0x64, reg);
 284                pci_dev_put(isa_dev);
 285                return 0;
 286        }
 287        printk(KERN_WARNING DRV_NAME ": Unable to find bridge.\n");
 288        return -ENODEV;
 289}
 290
 291static int serverworks_fixup_csb(struct pci_dev *pdev)
 292{
 293        u8 btr;
 294
 295        /* Third Channel Test */
 296        if (!(PCI_FUNC(pdev->devfn) & 1)) {
 297                struct pci_dev * findev = NULL;
 298                u32 reg4c = 0;
 299                findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 300                        PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
 301                if (findev) {
 302                        pci_read_config_dword(findev, 0x4C, &reg4c);
 303                        reg4c &= ~0x000007FF;
 304                        reg4c |=  0x00000040;
 305                        reg4c |=  0x00000020;
 306                        pci_write_config_dword(findev, 0x4C, reg4c);
 307                        pci_dev_put(findev);
 308                }
 309        } else {
 310                struct pci_dev * findev = NULL;
 311                u8 reg41 = 0;
 312
 313                findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 314                                PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
 315                if (findev) {
 316                        pci_read_config_byte(findev, 0x41, &reg41);
 317                        reg41 &= ~0x40;
 318                        pci_write_config_byte(findev, 0x41, reg41);
 319                        pci_dev_put(findev);
 320                }
 321        }
 322        /* setup the UDMA Control register
 323         *
 324         * 1. clear bit 6 to enable DMA
 325         * 2. enable DMA modes with bits 0-1
 326         *      00 : legacy
 327         *      01 : udma2
 328         *      10 : udma2/udma4
 329         *      11 : udma2/udma4/udma5
 330         */
 331        pci_read_config_byte(pdev, 0x5A, &btr);
 332        btr &= ~0x40;
 333        if (!(PCI_FUNC(pdev->devfn) & 1))
 334                btr |= 0x2;
 335        else
 336                btr |= (pdev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
 337        pci_write_config_byte(pdev, 0x5A, btr);
 338
 339        return btr;
 340}
 341
 342static void serverworks_fixup_ht1000(struct pci_dev *pdev)
 343{
 344        u8 btr;
 345        /* Setup HT1000 SouthBridge Controller - Single Channel Only */
 346        pci_read_config_byte(pdev, 0x5A, &btr);
 347        btr &= ~0x40;
 348        btr |= 0x3;
 349        pci_write_config_byte(pdev, 0x5A, btr);
 350}
 351
 352static int serverworks_fixup(struct pci_dev *pdev)
 353{
 354        int rc = 0;
 355
 356        /* Force master latency timer to 64 PCI clocks */
 357        pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
 358
 359        switch (pdev->device) {
 360        case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
 361                rc = serverworks_fixup_osb4(pdev);
 362                break;
 363        case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 364                ata_pci_bmdma_clear_simplex(pdev);
 365                /* fall through */
 366        case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 367        case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 368                rc = serverworks_fixup_csb(pdev);
 369                break;
 370        case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 371                serverworks_fixup_ht1000(pdev);
 372                break;
 373        }
 374
 375        return rc;
 376}
 377
 378static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 379{
 380        static const struct ata_port_info info[4] = {
 381                { /* OSB4 */
 382                        .flags = ATA_FLAG_SLAVE_POSS,
 383                        .pio_mask = ATA_PIO4,
 384                        .mwdma_mask = ATA_MWDMA2,
 385                        .udma_mask = ATA_UDMA2,
 386                        .port_ops = &serverworks_osb4_port_ops
 387                }, { /* OSB4 no UDMA */
 388                        .flags = ATA_FLAG_SLAVE_POSS,
 389                        .pio_mask = ATA_PIO4,
 390                        .mwdma_mask = ATA_MWDMA2,
 391                        /* No UDMA */
 392                        .port_ops = &serverworks_osb4_port_ops
 393                }, { /* CSB5 */
 394                        .flags = ATA_FLAG_SLAVE_POSS,
 395                        .pio_mask = ATA_PIO4,
 396                        .mwdma_mask = ATA_MWDMA2,
 397                        .udma_mask = ATA_UDMA4,
 398                        .port_ops = &serverworks_csb_port_ops
 399                }, { /* CSB5 - later revisions*/
 400                        .flags = ATA_FLAG_SLAVE_POSS,
 401                        .pio_mask = ATA_PIO4,
 402                        .mwdma_mask = ATA_MWDMA2,
 403                        .udma_mask = ATA_UDMA5,
 404                        .port_ops = &serverworks_csb_port_ops
 405                }
 406        };
 407        const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
 408        int rc;
 409
 410        rc = pcim_enable_device(pdev);
 411        if (rc)
 412                return rc;
 413
 414        rc = serverworks_fixup(pdev);
 415
 416        /* OSB4 : South Bridge and IDE */
 417        if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
 418                /* Select non UDMA capable OSB4 if we can't do fixups */
 419                if (rc < 0)
 420                        ppi[0] = &info[1];
 421        }
 422        /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
 423        else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
 424                 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 425                 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 426
 427                 /* If the returned btr is the newer revision then
 428                    select the right info block */
 429                 if (rc == 3)
 430                        ppi[0] = &info[3];
 431
 432                /* Is this the 3rd channel CSB6 IDE ? */
 433                if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
 434                        ppi[1] = &ata_dummy_port_info;
 435        }
 436
 437        return ata_pci_bmdma_init_one(pdev, ppi, &serverworks_sht, NULL, 0);
 438}
 439
 440#ifdef CONFIG_PM
 441static int serverworks_reinit_one(struct pci_dev *pdev)
 442{
 443        struct ata_host *host = dev_get_drvdata(&pdev->dev);
 444        int rc;
 445
 446        rc = ata_pci_device_do_resume(pdev);
 447        if (rc)
 448                return rc;
 449
 450        (void)serverworks_fixup(pdev);
 451
 452        ata_host_resume(host);
 453        return 0;
 454}
 455#endif
 456
 457static const struct pci_device_id serverworks[] = {
 458        { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
 459        { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
 460        { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
 461        { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
 462        { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
 463
 464        { },
 465};
 466
 467static struct pci_driver serverworks_pci_driver = {
 468        .name           = DRV_NAME,
 469        .id_table       = serverworks,
 470        .probe          = serverworks_init_one,
 471        .remove         = ata_pci_remove_one,
 472#ifdef CONFIG_PM
 473        .suspend        = ata_pci_device_suspend,
 474        .resume         = serverworks_reinit_one,
 475#endif
 476};
 477
 478static int __init serverworks_init(void)
 479{
 480        return pci_register_driver(&serverworks_pci_driver);
 481}
 482
 483static void __exit serverworks_exit(void)
 484{
 485        pci_unregister_driver(&serverworks_pci_driver);
 486}
 487
 488MODULE_AUTHOR("Alan Cox");
 489MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
 490MODULE_LICENSE("GPL");
 491MODULE_DEVICE_TABLE(pci, serverworks);
 492MODULE_VERSION(DRV_VERSION);
 493
 494module_init(serverworks_init);
 495module_exit(serverworks_exit);
 496