1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21#include <linux/types.h>
22#include <linux/gpio.h>
23#include <linux/init.h>
24#include <linux/mm.h>
25#include <linux/module.h>
26#include <linux/platform_device.h>
27#include <linux/spi/spi.h>
28#include <linux/mtd/physmap.h>
29#include <linux/input.h>
30#include <linux/gpio_keys.h>
31
32#include <asm/setup.h>
33#include <asm/mach-types.h>
34#include <asm/irq.h>
35
36#include <asm/mach/arch.h>
37#include <asm/mach/map.h>
38#include <asm/mach/irq.h>
39
40#include <mach/hardware.h>
41#include <mach/board.h>
42
43#include "generic.h"
44
45
46static void __init csb337_init_early(void)
47{
48
49 at91_initialize(3686400);
50
51
52 at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
53
54
55 at91_register_uart(0, 0, 0);
56
57
58 at91_set_serial_console(0);
59}
60
61static struct macb_platform_data __initdata csb337_eth_data = {
62 .phy_irq_pin = AT91_PIN_PC2,
63 .is_rmii = 0,
64};
65
66static struct at91_usbh_data __initdata csb337_usbh_data = {
67 .ports = 2,
68 .vbus_pin = {-EINVAL, -EINVAL},
69 .overcurrent_pin= {-EINVAL, -EINVAL},
70};
71
72static struct at91_udc_data __initdata csb337_udc_data = {
73 .pullup_pin = AT91_PIN_PA24,
74 .vbus_pin = -EINVAL,
75};
76
77static struct i2c_board_info __initdata csb337_i2c_devices[] = {
78 {
79 I2C_BOARD_INFO("ds1307", 0x68),
80 },
81};
82
83static struct at91_cf_data __initdata csb337_cf_data = {
84
85
86
87
88
89
90 .det_pin = AT91_PIN_PC3,
91
92
93 .irq_pin = AT91_PIN_PA19,
94 .vcc_pin = AT91_PIN_PD0,
95 .rst_pin = AT91_PIN_PD2,
96};
97
98static struct at91_mmc_data __initdata csb337_mmc_data = {
99 .det_pin = AT91_PIN_PD5,
100 .slot_b = 0,
101 .wire4 = 1,
102 .wp_pin = AT91_PIN_PD6,
103 .vcc_pin = -EINVAL,
104};
105
106static struct spi_board_info csb337_spi_devices[] = {
107 {
108 .modalias = "sak82c900",
109 .chip_select = 0,
110 .max_speed_hz = 6 * 1000 * 1000,
111 },
112};
113
114#define CSB_FLASH_BASE AT91_CHIPSELECT_0
115#define CSB_FLASH_SIZE SZ_8M
116
117static struct mtd_partition csb_flash_partitions[] = {
118 {
119 .name = "uMON flash",
120 .offset = 0,
121 .size = MTDPART_SIZ_FULL,
122 .mask_flags = MTD_WRITEABLE,
123 }
124};
125
126static struct physmap_flash_data csb_flash_data = {
127 .width = 2,
128 .parts = csb_flash_partitions,
129 .nr_parts = ARRAY_SIZE(csb_flash_partitions),
130};
131
132static struct resource csb_flash_resources[] = {
133 {
134 .start = CSB_FLASH_BASE,
135 .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
136 .flags = IORESOURCE_MEM,
137 }
138};
139
140static struct platform_device csb_flash = {
141 .name = "physmap-flash",
142 .id = 0,
143 .dev = {
144 .platform_data = &csb_flash_data,
145 },
146 .resource = csb_flash_resources,
147 .num_resources = ARRAY_SIZE(csb_flash_resources),
148};
149
150
151
152
153#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
154static struct gpio_keys_button csb300_buttons[] = {
155 {
156 .gpio = AT91_PIN_PB29,
157 .code = BTN_0,
158 .desc = "sw0",
159 .active_low = 1,
160 .wakeup = 1,
161 },
162 {
163 .gpio = AT91_PIN_PB28,
164 .code = BTN_1,
165 .desc = "sw1",
166 .active_low = 1,
167 .wakeup = 1,
168 },
169 {
170 .gpio = AT91_PIN_PA21,
171 .code = BTN_2,
172 .desc = "sw2",
173 .active_low = 1,
174 .wakeup = 1,
175 }
176};
177
178static struct gpio_keys_platform_data csb300_button_data = {
179 .buttons = csb300_buttons,
180 .nbuttons = ARRAY_SIZE(csb300_buttons),
181};
182
183static struct platform_device csb300_button_device = {
184 .name = "gpio-keys",
185 .id = -1,
186 .num_resources = 0,
187 .dev = {
188 .platform_data = &csb300_button_data,
189 }
190};
191
192static void __init csb300_add_device_buttons(void)
193{
194 at91_set_gpio_input(AT91_PIN_PB29, 1);
195 at91_set_deglitch(AT91_PIN_PB29, 1);
196 at91_set_gpio_input(AT91_PIN_PB28, 1);
197 at91_set_deglitch(AT91_PIN_PB28, 1);
198 at91_set_gpio_input(AT91_PIN_PA21, 1);
199 at91_set_deglitch(AT91_PIN_PA21, 1);
200
201 platform_device_register(&csb300_button_device);
202}
203#else
204static void __init csb300_add_device_buttons(void) {}
205#endif
206
207static struct gpio_led csb_leds[] = {
208 {
209 .name = "led0",
210 .gpio = AT91_PIN_PB2,
211 .active_low = 1,
212 .default_trigger = "heartbeat",
213 },
214 {
215 .name = "led1",
216 .gpio = AT91_PIN_PB1,
217 .active_low = 1,
218 .default_trigger = "mmc0",
219 },
220 {
221 .name = "led2",
222 .gpio = AT91_PIN_PB0,
223 .active_low = 1,
224 .default_trigger = "ide-disk",
225 }
226};
227
228
229static void __init csb337_board_init(void)
230{
231
232 at91_add_device_serial();
233
234 at91_add_device_eth(&csb337_eth_data);
235
236 at91_add_device_usbh(&csb337_usbh_data);
237
238 at91_add_device_udc(&csb337_udc_data);
239
240 at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
241
242 at91_set_gpio_input(AT91_PIN_PB22, 1);
243 at91_add_device_cf(&csb337_cf_data);
244
245 at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
246
247 at91_add_device_mmc(0, &csb337_mmc_data);
248
249 platform_device_register(&csb_flash);
250
251 at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
252
253 csb300_add_device_buttons();
254}
255
256MACHINE_START(CSB337, "Cogent CSB337")
257
258 .timer = &at91rm9200_timer,
259 .map_io = at91_map_io,
260 .init_early = csb337_init_early,
261 .init_irq = at91_init_irq_default,
262 .init_machine = csb337_board_init,
263MACHINE_END
264
