1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21#include <linux/types.h>
22#include <linux/gpio.h>
23#include <linux/init.h>
24#include <linux/mm.h>
25#include <linux/module.h>
26#include <linux/platform_device.h>
27#include <linux/spi/spi.h>
28#include <linux/mtd/physmap.h>
29#include <linux/input.h>
30#include <linux/gpio_keys.h>
31
32#include <asm/setup.h>
33#include <asm/mach-types.h>
34#include <asm/irq.h>
35
36#include <asm/mach/arch.h>
37#include <asm/mach/map.h>
38#include <asm/mach/irq.h>
39
40#include <mach/hardware.h>
41#include <mach/board.h>
42
43#include "generic.h"
44
45
46static void __init csb337_init_early(void)
47{
48
49 at91_initialize(3686400);
50}
51
52static struct macb_platform_data __initdata csb337_eth_data = {
53 .phy_irq_pin = AT91_PIN_PC2,
54 .is_rmii = 0,
55};
56
57static struct at91_usbh_data __initdata csb337_usbh_data = {
58 .ports = 2,
59 .vbus_pin = {-EINVAL, -EINVAL},
60 .overcurrent_pin= {-EINVAL, -EINVAL},
61};
62
63static struct at91_udc_data __initdata csb337_udc_data = {
64 .pullup_pin = AT91_PIN_PA24,
65 .vbus_pin = -EINVAL,
66};
67
68static struct i2c_board_info __initdata csb337_i2c_devices[] = {
69 {
70 I2C_BOARD_INFO("ds1307", 0x68),
71 },
72};
73
74static struct at91_cf_data __initdata csb337_cf_data = {
75
76
77
78
79
80
81 .det_pin = AT91_PIN_PC3,
82
83
84 .irq_pin = AT91_PIN_PA19,
85 .vcc_pin = AT91_PIN_PD0,
86 .rst_pin = AT91_PIN_PD2,
87};
88
89static struct at91_mmc_data __initdata csb337_mmc_data = {
90 .det_pin = AT91_PIN_PD5,
91 .slot_b = 0,
92 .wire4 = 1,
93 .wp_pin = AT91_PIN_PD6,
94 .vcc_pin = -EINVAL,
95};
96
97static struct spi_board_info csb337_spi_devices[] = {
98 {
99 .modalias = "sak82c900",
100 .chip_select = 0,
101 .max_speed_hz = 6 * 1000 * 1000,
102 },
103};
104
105#define CSB_FLASH_BASE AT91_CHIPSELECT_0
106#define CSB_FLASH_SIZE SZ_8M
107
108static struct mtd_partition csb_flash_partitions[] = {
109 {
110 .name = "uMON flash",
111 .offset = 0,
112 .size = MTDPART_SIZ_FULL,
113 .mask_flags = MTD_WRITEABLE,
114 }
115};
116
117static struct physmap_flash_data csb_flash_data = {
118 .width = 2,
119 .parts = csb_flash_partitions,
120 .nr_parts = ARRAY_SIZE(csb_flash_partitions),
121};
122
123static struct resource csb_flash_resources[] = {
124 {
125 .start = CSB_FLASH_BASE,
126 .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
127 .flags = IORESOURCE_MEM,
128 }
129};
130
131static struct platform_device csb_flash = {
132 .name = "physmap-flash",
133 .id = 0,
134 .dev = {
135 .platform_data = &csb_flash_data,
136 },
137 .resource = csb_flash_resources,
138 .num_resources = ARRAY_SIZE(csb_flash_resources),
139};
140
141
142
143
144#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
145static struct gpio_keys_button csb300_buttons[] = {
146 {
147 .gpio = AT91_PIN_PB29,
148 .code = BTN_0,
149 .desc = "sw0",
150 .active_low = 1,
151 .wakeup = 1,
152 },
153 {
154 .gpio = AT91_PIN_PB28,
155 .code = BTN_1,
156 .desc = "sw1",
157 .active_low = 1,
158 .wakeup = 1,
159 },
160 {
161 .gpio = AT91_PIN_PA21,
162 .code = BTN_2,
163 .desc = "sw2",
164 .active_low = 1,
165 .wakeup = 1,
166 }
167};
168
169static struct gpio_keys_platform_data csb300_button_data = {
170 .buttons = csb300_buttons,
171 .nbuttons = ARRAY_SIZE(csb300_buttons),
172};
173
174static struct platform_device csb300_button_device = {
175 .name = "gpio-keys",
176 .id = -1,
177 .num_resources = 0,
178 .dev = {
179 .platform_data = &csb300_button_data,
180 }
181};
182
183static void __init csb300_add_device_buttons(void)
184{
185 at91_set_gpio_input(AT91_PIN_PB29, 1);
186 at91_set_deglitch(AT91_PIN_PB29, 1);
187 at91_set_gpio_input(AT91_PIN_PB28, 1);
188 at91_set_deglitch(AT91_PIN_PB28, 1);
189 at91_set_gpio_input(AT91_PIN_PA21, 1);
190 at91_set_deglitch(AT91_PIN_PA21, 1);
191
192 platform_device_register(&csb300_button_device);
193}
194#else
195static void __init csb300_add_device_buttons(void) {}
196#endif
197
198static struct gpio_led csb_leds[] = {
199 {
200 .name = "led0",
201 .gpio = AT91_PIN_PB2,
202 .active_low = 1,
203 .default_trigger = "heartbeat",
204 },
205 {
206 .name = "led1",
207 .gpio = AT91_PIN_PB1,
208 .active_low = 1,
209 .default_trigger = "mmc0",
210 },
211 {
212 .name = "led2",
213 .gpio = AT91_PIN_PB0,
214 .active_low = 1,
215 .default_trigger = "ide-disk",
216 }
217};
218
219
220static void __init csb337_board_init(void)
221{
222
223 at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
224
225
226 at91_register_uart(0, 0, 0);
227 at91_add_device_serial();
228
229 at91_add_device_eth(&csb337_eth_data);
230
231 at91_add_device_usbh(&csb337_usbh_data);
232
233 at91_add_device_udc(&csb337_udc_data);
234
235 at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
236
237 at91_set_gpio_input(AT91_PIN_PB22, 1);
238 at91_add_device_cf(&csb337_cf_data);
239
240 at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
241
242 at91_add_device_mmc(0, &csb337_mmc_data);
243
244 platform_device_register(&csb_flash);
245
246 at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
247
248 csb300_add_device_buttons();
249}
250
251MACHINE_START(CSB337, "Cogent CSB337")
252
253 .timer = &at91rm9200_timer,
254 .map_io = at91_map_io,
255 .init_early = csb337_init_early,
256 .init_irq = at91_init_irq_default,
257 .init_machine = csb337_board_init,
258MACHINE_END
259
