1#ifndef _SPARC64_BACKOFF_H 2#define _SPARC64_BACKOFF_H 3 4/* The macros in this file implement an exponential backoff facility 5 * for atomic operations. 6 * 7 * When multiple threads compete on an atomic operation, it is 8 * possible for one thread to be continually denied a successful 9 * completion of the compare-and-swap instruction. Heavily 10 * threaded cpu implementations like Niagara can compound this 11 * problem even further. 12 * 13 * When an atomic operation fails and needs to be retried, we spin a 14 * certain number of times. At each subsequent failure of the same 15 * operation we double the spin count, realizing an exponential 16 * backoff. 17 * 18 * When we spin, we try to use an operation that will cause the 19 * current cpu strand to block, and therefore make the core fully 20 * available to any other other runnable strands. There are two 21 * options, based upon cpu capabilities. 22 * 23 * On all cpus prior to SPARC-T4 we do three dummy reads of the 24 * condition code register. Each read blocks the strand for something 25 * between 40 and 50 cpu cycles. 26 * 27 * For SPARC-T4 and later we have a special "pause" instruction 28 * available. This is implemented using writes to register %asr27. 29 * The cpu will block the number of cycles written into the register, 30 * unless a disrupting trap happens first. SPARC-T4 specifically 31 * implements pause with a granularity of 8 cycles. Each strand has 32 * an internal pause counter which decrements every 8 cycles. So the 33 * chip shifts the %asr27 value down by 3 bits, and writes the result 34 * into the pause counter. If a value smaller than 8 is written, the 35 * chip blocks for 1 cycle. 36 * 37 * To achieve the same amount of backoff as the three %ccr reads give 38 * on earlier chips, we shift the backoff value up by 7 bits. (Three 39 * %ccr reads block for about 128 cycles, 1 << 7 == 128) We write the 40 * whole amount we want to block into the pause register, rather than 41 * loop writing 128 each time. 42 */ 43 44#define BACKOFF_LIMIT (4 * 1024) 45 46#ifdef CONFIG_SMP 47 48#define BACKOFF_SETUP(reg) \ 49 mov 1, reg 50 51#define BACKOFF_LABEL(spin_label, continue_label) \ 52 spin_label 53 54#define BACKOFF_SPIN(reg, tmp, label) \ 55 mov reg, tmp; \ 5688: rd %ccr, %g0; \ 57 rd %ccr, %g0; \ 58 rd %ccr, %g0; \ 59 .section .pause_3insn_patch,"ax";\ 60 .word 88b; \ 61 sllx tmp, 7, tmp; \ 62 wr tmp, 0, %asr27; \ 63 clr tmp; \ 64 .previous; \ 65 brnz,pt tmp, 88b; \ 66 sub tmp, 1, tmp; \ 67 set BACKOFF_LIMIT, tmp; \ 68 cmp reg, tmp; \ 69 bg,pn %xcc, label; \ 70 nop; \ 71 ba,pt %xcc, label; \ 72 sllx reg, 1, reg; 73 74#else 75 76#define BACKOFF_SETUP(reg) 77 78#define BACKOFF_LABEL(spin_label, continue_label) \ 79 continue_label 80 81#define BACKOFF_SPIN(reg, tmp, label) 82 83#endif 84 85#endif /* _SPARC64_BACKOFF_H */ 86