1/* 2 Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> 3 <http://rt2x00.serialmonkey.com> 4 5 This program is free software; you can redistribute it and/or modify 6 it under the terms of the GNU General Public License as published by 7 the Free Software Foundation; either version 2 of the License, or 8 (at your option) any later version. 9 10 This program is distributed in the hope that it will be useful, 11 but WITHOUT ANY WARRANTY; without even the implied warranty of 12 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 GNU General Public License for more details. 14 15 You should have received a copy of the GNU General Public License 16 along with this program; if not, see <http://www.gnu.org/licenses/>. 17 */ 18 19/* 20 Module: rt2500pci 21 Abstract: Data structures and registers for the rt2500pci module. 22 Supported chipsets: RT2560. 23 */ 24 25#ifndef RT2500PCI_H 26#define RT2500PCI_H 27 28/* 29 * RF chip defines. 30 */ 31#define RF2522 0x0000 32#define RF2523 0x0001 33#define RF2524 0x0002 34#define RF2525 0x0003 35#define RF2525E 0x0004 36#define RF5222 0x0010 37 38/* 39 * RT2560 version 40 */ 41#define RT2560_VERSION_B 2 42#define RT2560_VERSION_C 3 43#define RT2560_VERSION_D 4 44 45/* 46 * Signal information. 47 * Default offset is required for RSSI <-> dBm conversion. 48 */ 49#define DEFAULT_RSSI_OFFSET 121 50 51/* 52 * Register layout information. 53 */ 54#define CSR_REG_BASE 0x0000 55#define CSR_REG_SIZE 0x0174 56#define EEPROM_BASE 0x0000 57#define EEPROM_SIZE 0x0200 58#define BBP_BASE 0x0000 59#define BBP_SIZE 0x0040 60#define RF_BASE 0x0004 61#define RF_SIZE 0x0010 62 63/* 64 * Number of TX queues. 65 */ 66#define NUM_TX_QUEUES 2 67 68/* 69 * Control/Status Registers(CSR). 70 * Some values are set in TU, whereas 1 TU == 1024 us. 71 */ 72 73/* 74 * CSR0: ASIC revision number. 75 */ 76#define CSR0 0x0000 77#define CSR0_REVISION FIELD32(0x0000ffff) 78 79/* 80 * CSR1: System control register. 81 * SOFT_RESET: Software reset, 1: reset, 0: normal. 82 * BBP_RESET: Hardware reset, 1: reset, 0, release. 83 * HOST_READY: Host ready after initialization. 84 */ 85#define CSR1 0x0004 86#define CSR1_SOFT_RESET FIELD32(0x00000001) 87#define CSR1_BBP_RESET FIELD32(0x00000002) 88#define CSR1_HOST_READY FIELD32(0x00000004) 89 90/* 91 * CSR2: System admin status register (invalid). 92 */ 93#define CSR2 0x0008 94 95/* 96 * CSR3: STA MAC address register 0. 97 */ 98#define CSR3 0x000c 99#define CSR3_BYTE0 FIELD32(0x000000ff) 100#define CSR3_BYTE1 FIELD32(0x0000ff00) 101#define CSR3_BYTE2 FIELD32(0x00ff0000) 102#define CSR3_BYTE3 FIELD32(0xff000000) 103 104/* 105 * CSR4: STA MAC address register 1. 106 */ 107#define CSR4 0x0010 108#define CSR4_BYTE4 FIELD32(0x000000ff) 109#define CSR4_BYTE5 FIELD32(0x0000ff00) 110 111/* 112 * CSR5: BSSID register 0. 113 */ 114#define CSR5 0x0014 115#define CSR5_BYTE0 FIELD32(0x000000ff) 116#define CSR5_BYTE1 FIELD32(0x0000ff00) 117#define CSR5_BYTE2 FIELD32(0x00ff0000) 118#define CSR5_BYTE3 FIELD32(0xff000000) 119 120/* 121 * CSR6: BSSID register 1. 122 */ 123#define CSR6 0x0018 124#define CSR6_BYTE4 FIELD32(0x000000ff) 125#define CSR6_BYTE5 FIELD32(0x0000ff00) 126 127/* 128 * CSR7: Interrupt source register. 129 * Write 1 to clear. 130 * TBCN_EXPIRE: Beacon timer expired interrupt. 131 * TWAKE_EXPIRE: Wakeup timer expired interrupt. 132 * TATIMW_EXPIRE: Timer of atim window expired interrupt. 133 * TXDONE_TXRING: Tx ring transmit done interrupt. 134 * TXDONE_ATIMRING: Atim ring transmit done interrupt. 135 * TXDONE_PRIORING: Priority ring transmit done interrupt. 136 * RXDONE: Receive done interrupt. 137 * DECRYPTION_DONE: Decryption done interrupt. 138 * ENCRYPTION_DONE: Encryption done interrupt. 139 * UART1_TX_TRESHOLD: UART1 TX reaches threshold. 140 * UART1_RX_TRESHOLD: UART1 RX reaches threshold. 141 * UART1_IDLE_TRESHOLD: UART1 IDLE over threshold. 142 * UART1_TX_BUFF_ERROR: UART1 TX buffer error. 143 * UART1_RX_BUFF_ERROR: UART1 RX buffer error. 144 * UART2_TX_TRESHOLD: UART2 TX reaches threshold. 145 * UART2_RX_TRESHOLD: UART2 RX reaches threshold. 146 * UART2_IDLE_TRESHOLD: UART2 IDLE over threshold. 147 * UART2_TX_BUFF_ERROR: UART2 TX buffer error. 148 * UART2_RX_BUFF_ERROR: UART2 RX buffer error. 149 * TIMER_CSR3_EXPIRE: TIMECSR3 timer expired (802.1H quiet period). 150 151 */ 152#define CSR7 0x001c 153#define CSR7_TBCN_EXPIRE FIELD32(0x00000001) 154#define CSR7_TWAKE_EXPIRE FIELD32(0x00000002) 155#define CSR7_TATIMW_EXPIRE FIELD32(0x00000004) 156#define CSR7_TXDONE_TXRING FIELD32(0x00000008) 157#define CSR7_TXDONE_ATIMRING FIELD32(0x00000010) 158#define CSR7_TXDONE_PRIORING FIELD32(0x00000020) 159#define CSR7_RXDONE FIELD32(0x00000040) 160#define CSR7_DECRYPTION_DONE FIELD32(0x00000080) 161#define CSR7_ENCRYPTION_DONE FIELD32(0x00000100) 162#define CSR7_UART1_TX_TRESHOLD FIELD32(0x00000200) 163#define CSR7_UART1_RX_TRESHOLD FIELD32(0x00000400) 164#define CSR7_UART1_IDLE_TRESHOLD FIELD32(0x00000800) 165#define CSR7_UART1_TX_BUFF_ERROR FIELD32(0x00001000) 166#define CSR7_UART1_RX_BUFF_ERROR FIELD32(0x00002000) 167#define CSR7_UART2_TX_TRESHOLD FIELD32(0x00004000) 168#define CSR7_UART2_RX_TRESHOLD FIELD32(0x00008000) 169#define CSR7_UART2_IDLE_TRESHOLD FIELD32(0x00010000) 170#define CSR7_UART2_TX_BUFF_ERROR FIELD32(0x00020000) 171#define CSR7_UART2_RX_BUFF_ERROR FIELD32(0x00040000) 172#define CSR7_TIMER_CSR3_EXPIRE FIELD32(0x00080000) 173 174/* 175 * CSR8: Interrupt mask register. 176 * Write 1 to mask interrupt. 177 * TBCN_EXPIRE: Beacon timer expired interrupt. 178 * TWAKE_EXPIRE: Wakeup timer expired interrupt. 179 * TATIMW_EXPIRE: Timer of atim window expired interrupt. 180 * TXDONE_TXRING: Tx ring transmit done interrupt. 181 * TXDONE_ATIMRING: Atim ring transmit done interrupt. 182 * TXDONE_PRIORING: Priority ring transmit done interrupt. 183 * RXDONE: Receive done interrupt. 184 * DECRYPTION_DONE: Decryption done interrupt. 185 * ENCRYPTION_DONE: Encryption done interrupt. 186 * UART1_TX_TRESHOLD: UART1 TX reaches threshold. 187 * UART1_RX_TRESHOLD: UART1 RX reaches threshold. 188 * UART1_IDLE_TRESHOLD: UART1 IDLE over threshold. 189 * UART1_TX_BUFF_ERROR: UART1 TX buffer error. 190 * UART1_RX_BUFF_ERROR: UART1 RX buffer error. 191 * UART2_TX_TRESHOLD: UART2 TX reaches threshold. 192 * UART2_RX_TRESHOLD: UART2 RX reaches threshold. 193 * UART2_IDLE_TRESHOLD: UART2 IDLE over threshold. 194 * UART2_TX_BUFF_ERROR: UART2 TX buffer error. 195 * UART2_RX_BUFF_ERROR: UART2 RX buffer error. 196 * TIMER_CSR3_EXPIRE: TIMECSR3 timer expired (802.1H quiet period). 197 */ 198#define CSR8 0x0020 199#define CSR8_TBCN_EXPIRE FIELD32(0x00000001) 200#define CSR8_TWAKE_EXPIRE FIELD32(0x00000002) 201#define CSR8_TATIMW_EXPIRE FIELD32(0x00000004) 202#define CSR8_TXDONE_TXRING FIELD32(0x00000008) 203#define CSR8_TXDONE_ATIMRING FIELD32(0x00000010) 204#define CSR8_TXDONE_PRIORING FIELD32(0x00000020) 205#define CSR8_RXDONE FIELD32(0x00000040) 206#define CSR8_DECRYPTION_DONE FIELD32(0x00000080) 207#define CSR8_ENCRYPTION_DONE FIELD32(0x00000100) 208#define CSR8_UART1_TX_TRESHOLD FIELD32(0x00000200) 209#define CSR8_UART1_RX_TRESHOLD FIELD32(0x00000400) 210#define CSR8_UART1_IDLE_TRESHOLD FIELD32(0x00000800) 211#define CSR8_UART1_TX_BUFF_ERROR FIELD32(0x00001000) 212#define CSR8_UART1_RX_BUFF_ERROR FIELD32(0x00002000) 213#define CSR8_UART2_TX_TRESHOLD FIELD32(0x00004000) 214#define CSR8_UART2_RX_TRESHOLD FIELD32(0x00008000) 215#define CSR8_UART2_IDLE_TRESHOLD FIELD32(0x00010000) 216#define CSR8_UART2_TX_BUFF_ERROR FIELD32(0x00020000) 217#define CSR8_UART2_RX_BUFF_ERROR FIELD32(0x00040000) 218#define CSR8_TIMER_CSR3_EXPIRE FIELD32(0x00080000) 219 220/* 221 * CSR9: Maximum frame length register. 222 * MAX_FRAME_UNIT: Maximum frame length in 128b unit, default: 12. 223 */ 224#define CSR9 0x0024 225#define CSR9_MAX_FRAME_UNIT FIELD32(0x00000f80) 226 227/* 228 * SECCSR0: WEP control register. 229 * KICK_DECRYPT: Kick decryption engine, self-clear. 230 * ONE_SHOT: 0: ring mode, 1: One shot only mode. 231 * DESC_ADDRESS: Descriptor physical address of frame. 232 */ 233#define SECCSR0 0x0028 234#define SECCSR0_KICK_DECRYPT FIELD32(0x00000001) 235#define SECCSR0_ONE_SHOT FIELD32(0x00000002) 236#define SECCSR0_DESC_ADDRESS FIELD32(0xfffffffc) 237 238/* 239 * CSR11: Back-off control register. 240 * CWMIN: CWmin. Default cwmin is 31 (2^5 - 1). 241 * CWMAX: CWmax. Default cwmax is 1023 (2^10 - 1). 242 * SLOT_TIME: Slot time, default is 20us for 802.11b 243 * CW_SELECT: CWmin/CWmax selection, 1: Register, 0: TXD. 244 * LONG_RETRY: Long retry count. 245 * SHORT_RETRY: Short retry count. 246 */ 247#define CSR11 0x002c 248#define CSR11_CWMIN FIELD32(0x0000000f) 249#define CSR11_CWMAX FIELD32(0x000000f0) 250#define CSR11_SLOT_TIME FIELD32(0x00001f00) 251#define CSR11_CW_SELECT FIELD32(0x00002000) 252#define CSR11_LONG_RETRY FIELD32(0x00ff0000) 253#define CSR11_SHORT_RETRY FIELD32(0xff000000) 254 255/* 256 * CSR12: Synchronization configuration register 0. 257 * All units in 1/16 TU. 258 * BEACON_INTERVAL: Beacon interval, default is 100 TU. 259 * CFP_MAX_DURATION: Cfp maximum duration, default is 100 TU. 260 */ 261#define CSR12 0x0030 262#define CSR12_BEACON_INTERVAL FIELD32(0x0000ffff) 263#define CSR12_CFP_MAX_DURATION FIELD32(0xffff0000) 264 265/* 266 * CSR13: Synchronization configuration register 1. 267 * All units in 1/16 TU. 268 * ATIMW_DURATION: Atim window duration. 269 * CFP_PERIOD: Cfp period, default is 0 TU. 270 */ 271#define CSR13 0x0034 272#define CSR13_ATIMW_DURATION FIELD32(0x0000ffff) 273#define CSR13_CFP_PERIOD FIELD32(0x00ff0000) 274 275/* 276 * CSR14: Synchronization control register. 277 * TSF_COUNT: Enable tsf auto counting. 278 * TSF_SYNC: Tsf sync, 0: disable, 1: infra, 2: ad-hoc/master mode. 279 * TBCN: Enable tbcn with reload value. 280 * TCFP: Enable tcfp & cfp / cp switching. 281 * TATIMW: Enable tatimw & atim window switching. 282 * BEACON_GEN: Enable beacon generator. 283 * CFP_COUNT_PRELOAD: Cfp count preload value. 284 * TBCM_PRELOAD: Tbcn preload value in units of 64us. 285 */ 286#define CSR14 0x0038 287#define CSR14_TSF_COUNT FIELD32(0x00000001) 288#define CSR14_TSF_SYNC FIELD32(0x00000006) 289#define CSR14_TBCN FIELD32(0x00000008) 290#define CSR14_TCFP FIELD32(0x00000010) 291#define CSR14_TATIMW FIELD32(0x00000020) 292#define CSR14_BEACON_GEN FIELD32(0x00000040) 293#define CSR14_CFP_COUNT_PRELOAD FIELD32(0x0000ff00) 294#define CSR14_TBCM_PRELOAD FIELD32(0xffff0000) 295 296/* 297 * CSR15: Synchronization status register. 298 * CFP: ASIC is in contention-free period. 299 * ATIMW: ASIC is in ATIM window. 300 * BEACON_SENT: Beacon is send. 301 */ 302#define CSR15 0x003c 303#define CSR15_CFP FIELD32(0x00000001) 304#define CSR15_ATIMW FIELD32(0x00000002) 305#define CSR15_BEACON_SENT FIELD32(0x00000004) 306 307/* 308 * CSR16: TSF timer register 0. 309 */ 310#define CSR16 0x0040 311#define CSR16_LOW_TSFTIMER FIELD32(0xffffffff) 312 313/* 314 * CSR17: TSF timer register 1. 315 */ 316#define CSR17 0x0044 317#define CSR17_HIGH_TSFTIMER FIELD32(0xffffffff) 318 319/* 320 * CSR18: IFS timer register 0. 321 * SIFS: Sifs, default is 10 us. 322 * PIFS: Pifs, default is 30 us. 323 */ 324#define CSR18 0x0048 325#define CSR18_SIFS FIELD32(0x000001ff) 326#define CSR18_PIFS FIELD32(0x001f0000) 327 328/* 329 * CSR19: IFS timer register 1. 330 * DIFS: Difs, default is 50 us. 331 * EIFS: Eifs, default is 364 us. 332 */ 333#define CSR19 0x004c 334#define CSR19_DIFS FIELD32(0x0000ffff) 335#define CSR19_EIFS FIELD32(0xffff0000) 336 337/* 338 * CSR20: Wakeup timer register. 339 * DELAY_AFTER_TBCN: Delay after tbcn expired in units of 1/16 TU. 340 * TBCN_BEFORE_WAKEUP: Number of beacon before wakeup. 341 * AUTOWAKE: Enable auto wakeup / sleep mechanism. 342 */ 343#define CSR20 0x0050 344#define CSR20_DELAY_AFTER_TBCN FIELD32(0x0000ffff) 345#define CSR20_TBCN_BEFORE_WAKEUP FIELD32(0x00ff0000) 346#define CSR20_AUTOWAKE FIELD32(0x01000000) 347 348/* 349 * CSR21: EEPROM control register. 350 * RELOAD: Write 1 to reload eeprom content. 351 * TYPE_93C46: 1: 93c46, 0:93c66. 352 */ 353#define CSR21 0x0054 354#define CSR21_RELOAD FIELD32(0x00000001) 355#define CSR21_EEPROM_DATA_CLOCK FIELD32(0x00000002) 356#define CSR21_EEPROM_CHIP_SELECT FIELD32(0x00000004) 357#define CSR21_EEPROM_DATA_IN FIELD32(0x00000008) 358#define CSR21_EEPROM_DATA_OUT FIELD32(0x00000010) 359#define CSR21_TYPE_93C46 FIELD32(0x00000020) 360 361/* 362 * CSR22: CFP control register. 363 * CFP_DURATION_REMAIN: Cfp duration remain, in units of TU. 364 * RELOAD_CFP_DURATION: Write 1 to reload cfp duration remain. 365 */ 366#define CSR22 0x0058 367#define CSR22_CFP_DURATION_REMAIN FIELD32(0x0000ffff) 368#define CSR22_RELOAD_CFP_DURATION FIELD32(0x00010000) 369 370/* 371 * Transmit related CSRs. 372 * Some values are set in TU, whereas 1 TU == 1024 us. 373 */ 374 375/* 376 * TXCSR0: TX Control Register. 377 * KICK_TX: Kick tx ring. 378 * KICK_ATIM: Kick atim ring. 379 * KICK_PRIO: Kick priority ring. 380 * ABORT: Abort all transmit related ring operation. 381 */ 382#define TXCSR0 0x0060 383#define TXCSR0_KICK_TX FIELD32(0x00000001) 384#define TXCSR0_KICK_ATIM FIELD32(0x00000002) 385#define TXCSR0_KICK_PRIO FIELD32(0x00000004) 386#define TXCSR0_ABORT FIELD32(0x00000008) 387 388/* 389 * TXCSR1: TX Configuration Register. 390 * ACK_TIMEOUT: Ack timeout, default = sifs + 2*slottime + acktime @ 1mbps. 391 * ACK_CONSUME_TIME: Ack consume time, default = sifs + acktime @ 1mbps. 392 * TSF_OFFSET: Insert tsf offset. 393 * AUTORESPONDER: Enable auto responder which include ack & cts. 394 */ 395#define TXCSR1 0x0064 396#define TXCSR1_ACK_TIMEOUT FIELD32(0x000001ff) 397#define TXCSR1_ACK_CONSUME_TIME FIELD32(0x0003fe00) 398#define TXCSR1_TSF_OFFSET FIELD32(0x00fc0000) 399#define TXCSR1_AUTORESPONDER FIELD32(0x01000000) 400 401/* 402 * TXCSR2: Tx descriptor configuration register. 403 * TXD_SIZE: Tx descriptor size, default is 48. 404 * NUM_TXD: Number of tx entries in ring. 405 * NUM_ATIM: Number of atim entries in ring. 406 * NUM_PRIO: Number of priority entries in ring. 407 */ 408#define TXCSR2 0x0068 409#define TXCSR2_TXD_SIZE FIELD32(0x000000ff) 410#define TXCSR2_NUM_TXD FIELD32(0x0000ff00) 411#define TXCSR2_NUM_ATIM FIELD32(0x00ff0000) 412#define TXCSR2_NUM_PRIO FIELD32(0xff000000) 413 414/* 415 * TXCSR3: TX Ring Base address register. 416 */ 417#define TXCSR3 0x006c 418#define TXCSR3_TX_RING_REGISTER FIELD32(0xffffffff) 419 420/* 421 * TXCSR4: TX Atim Ring Base address register. 422 */ 423#define TXCSR4 0x0070 424#define TXCSR4_ATIM_RING_REGISTER FIELD32(0xffffffff) 425 426/* 427 * TXCSR5: TX Prio Ring Base address register. 428 */ 429#define TXCSR5 0x0074 430#define TXCSR5_PRIO_RING_REGISTER FIELD32(0xffffffff) 431 432/* 433 * TXCSR6: Beacon Base address register. 434 */ 435#define TXCSR6 0x0078 436#define TXCSR6_BEACON_RING_REGISTER FIELD32(0xffffffff) 437 438/* 439 * TXCSR7: Auto responder control register. 440 * AR_POWERMANAGEMENT: Auto responder power management bit. 441 */ 442#define TXCSR7 0x007c 443#define TXCSR7_AR_POWERMANAGEMENT FIELD32(0x00000001) 444 445/* 446 * TXCSR8: CCK Tx BBP register. 447 */ 448#define TXCSR8 0x0098 449#define TXCSR8_BBP_ID0 FIELD32(0x0000007f) 450#define TXCSR8_BBP_ID0_VALID FIELD32(0x00000080) 451#define TXCSR8_BBP_ID1 FIELD32(0x00007f00) 452#define TXCSR8_BBP_ID1_VALID FIELD32(0x00008000) 453#define TXCSR8_BBP_ID2 FIELD32(0x007f0000) 454#define TXCSR8_BBP_ID2_VALID FIELD32(0x00800000) 455#define TXCSR8_BBP_ID3 FIELD32(0x7f000000) 456#define TXCSR8_BBP_ID3_VALID FIELD32(0x80000000) 457 458/* 459 * TXCSR9: OFDM TX BBP registers 460 * OFDM_SIGNAL: BBP rate field address for OFDM. 461 * OFDM_SERVICE: BBP service field address for OFDM. 462 * OFDM_LENGTH_LOW: BBP length low byte address for OFDM. 463 * OFDM_LENGTH_HIGH: BBP length high byte address for OFDM. 464 */ 465#define TXCSR9 0x0094 466#define TXCSR9_OFDM_RATE FIELD32(0x000000ff) 467#define TXCSR9_OFDM_SERVICE FIELD32(0x0000ff00) 468#define TXCSR9_OFDM_LENGTH_LOW FIELD32(0x00ff0000) 469#define TXCSR9_OFDM_LENGTH_HIGH FIELD32(0xff000000) 470 471/* 472 * Receive related CSRs. 473 * Some values are set in TU, whereas 1 TU == 1024 us. 474 */ 475 476/* 477 * RXCSR0: RX Control Register. 478 * DISABLE_RX: Disable rx engine. 479 * DROP_CRC: Drop crc error. 480 * DROP_PHYSICAL: Drop physical error. 481 * DROP_CONTROL: Drop control frame. 482 * DROP_NOT_TO_ME: Drop not to me unicast frame. 483 * DROP_TODS: Drop frame tods bit is true. 484 * DROP_VERSION_ERROR: Drop version error frame. 485 * PASS_CRC: Pass all packets with crc attached. 486 * PASS_CRC: Pass all packets with crc attached. 487 * PASS_PLCP: Pass all packets with 4 bytes PLCP attached. 488 * DROP_MCAST: Drop multicast frames. 489 * DROP_BCAST: Drop broadcast frames. 490 * ENABLE_QOS: Accept QOS data frame and parse QOS field. 491 */ 492#define RXCSR0 0x0080 493#define RXCSR0_DISABLE_RX FIELD32(0x00000001) 494#define RXCSR0_DROP_CRC FIELD32(0x00000002) 495#define RXCSR0_DROP_PHYSICAL FIELD32(0x00000004) 496#define RXCSR0_DROP_CONTROL FIELD32(0x00000008) 497#define RXCSR0_DROP_NOT_TO_ME FIELD32(0x00000010) 498#define RXCSR0_DROP_TODS FIELD32(0x00000020) 499#define RXCSR0_DROP_VERSION_ERROR FIELD32(0x00000040) 500#define RXCSR0_PASS_CRC FIELD32(0x00000080) 501#define RXCSR0_PASS_PLCP FIELD32(0x00000100) 502#define RXCSR0_DROP_MCAST FIELD32(0x00000200) 503#define RXCSR0_DROP_BCAST FIELD32(0x00000400) 504#define RXCSR0_ENABLE_QOS FIELD32(0x00000800) 505 506/* 507 * RXCSR1: RX descriptor configuration register. 508 * RXD_SIZE: Rx descriptor size, default is 32b. 509 * NUM_RXD: Number of rx entries in ring. 510 */ 511#define RXCSR1 0x0084 512#define RXCSR1_RXD_SIZE FIELD32(0x000000ff) 513#define RXCSR1_NUM_RXD FIELD32(0x0000ff00) 514 515/* 516 * RXCSR2: RX Ring base address register. 517 */ 518#define RXCSR2 0x0088 519#define RXCSR2_RX_RING_REGISTER FIELD32(0xffffffff) 520 521/* 522 * RXCSR3: BBP ID register for Rx operation. 523 * BBP_ID#: BBP register # id. 524 * BBP_ID#_VALID: BBP register # id is valid or not. 525 */ 526#define RXCSR3 0x0090 527#define RXCSR3_BBP_ID0 FIELD32(0x0000007f) 528#define RXCSR3_BBP_ID0_VALID FIELD32(0x00000080) 529#define RXCSR3_BBP_ID1 FIELD32(0x00007f00) 530#define RXCSR3_BBP_ID1_VALID FIELD32(0x00008000) 531#define RXCSR3_BBP_ID2 FIELD32(0x007f0000) 532#define RXCSR3_BBP_ID2_VALID FIELD32(0x00800000) 533#define RXCSR3_BBP_ID3 FIELD32(0x7f000000) 534#define RXCSR3_BBP_ID3_VALID FIELD32(0x80000000) 535 536/* 537 * ARCSR1: Auto Responder PLCP config register 1. 538 * AR_BBP_DATA#: Auto responder BBP register # data. 539 * AR_BBP_ID#: Auto responder BBP register # Id. 540 */ 541#define ARCSR1 0x009c 542#define ARCSR1_AR_BBP_DATA2 FIELD32(0x000000ff) 543#define ARCSR1_AR_BBP_ID2 FIELD32(0x0000ff00) 544#define ARCSR1_AR_BBP_DATA3 FIELD32(0x00ff0000) 545#define ARCSR1_AR_BBP_ID3 FIELD32(0xff000000) 546 547/* 548 * Miscellaneous Registers. 549 * Some values are set in TU, whereas 1 TU == 1024 us. 550 551 */ 552 553/* 554 * PCICSR: PCI control register. 555 * BIG_ENDIAN: 1: big endian, 0: little endian. 556 * RX_TRESHOLD: Rx threshold in dw to start pci access 557 * 0: 16dw (default), 1: 8dw, 2: 4dw, 3: 32dw. 558 * TX_TRESHOLD: Tx threshold in dw to start pci access 559 * 0: 0dw (default), 1: 1dw, 2: 4dw, 3: forward. 560 * BURST_LENTH: Pci burst length 0: 4dw (default, 1: 8dw, 2: 16dw, 3:32dw. 561 * ENABLE_CLK: Enable clk_run, pci clock can't going down to non-operational. 562 * READ_MULTIPLE: Enable memory read multiple. 563 * WRITE_INVALID: Enable memory write & invalid. 564 */ 565#define PCICSR 0x008c 566#define PCICSR_BIG_ENDIAN FIELD32(0x00000001) 567#define PCICSR_RX_TRESHOLD FIELD32(0x00000006) 568#define PCICSR_TX_TRESHOLD FIELD32(0x00000018) 569#define PCICSR_BURST_LENTH FIELD32(0x00000060) 570#define PCICSR_ENABLE_CLK FIELD32(0x00000080) 571#define PCICSR_READ_MULTIPLE FIELD32(0x00000100) 572#define PCICSR_WRITE_INVALID FIELD32(0x00000200) 573 574/* 575 * CNT0: FCS error count. 576 * FCS_ERROR: FCS error count, cleared when read. 577 */ 578#define CNT0 0x00a0 579#define CNT0_FCS_ERROR FIELD32(0x0000ffff) 580 581/* 582 * Statistic Register. 583 * CNT1: PLCP error count. 584 * CNT2: Long error count. 585 */ 586#define TIMECSR2 0x00a8 587#define CNT1 0x00ac 588#define CNT2 0x00b0 589#define TIMECSR3 0x00b4 590 591/* 592 * CNT3: CCA false alarm count. 593 */ 594#define CNT3 0x00b8 595#define CNT3_FALSE_CCA FIELD32(0x0000ffff) 596 597/* 598 * Statistic Register. 599 * CNT4: Rx FIFO overflow count. 600 * CNT5: Tx FIFO underrun count. 601 */ 602#define CNT4 0x00bc 603#define CNT5 0x00c0 604 605/* 606 * Baseband Control Register. 607 */ 608 609/* 610 * PWRCSR0: Power mode configuration register. 611 */ 612#define PWRCSR0 0x00c4 613 614/* 615 * Power state transition time registers. 616 */ 617#define PSCSR0 0x00c8 618#define PSCSR1 0x00cc 619#define PSCSR2 0x00d0 620#define PSCSR3 0x00d4 621 622/* 623 * PWRCSR1: Manual power control / status register. 624 * Allowed state: 0 deep_sleep, 1: sleep, 2: standby, 3: awake. 625 * SET_STATE: Set state. Write 1 to trigger, self cleared. 626 * BBP_DESIRE_STATE: BBP desired state. 627 * RF_DESIRE_STATE: RF desired state. 628 * BBP_CURR_STATE: BBP current state. 629 * RF_CURR_STATE: RF current state. 630 * PUT_TO_SLEEP: Put to sleep. Write 1 to trigger, self cleared. 631 */ 632#define PWRCSR1 0x00d8 633#define PWRCSR1_SET_STATE FIELD32(0x00000001) 634#define PWRCSR1_BBP_DESIRE_STATE FIELD32(0x00000006) 635#define PWRCSR1_RF_DESIRE_STATE FIELD32(0x00000018) 636#define PWRCSR1_BBP_CURR_STATE FIELD32(0x00000060) 637#define PWRCSR1_RF_CURR_STATE FIELD32(0x00000180) 638#define PWRCSR1_PUT_TO_SLEEP FIELD32(0x00000200) 639 640/* 641 * TIMECSR: Timer control register. 642 * US_COUNT: 1 us timer count in units of clock cycles. 643 * US_64_COUNT: 64 us timer count in units of 1 us timer. 644 * BEACON_EXPECT: Beacon expect window. 645 */ 646#define TIMECSR 0x00dc 647#define TIMECSR_US_COUNT FIELD32(0x000000ff) 648#define TIMECSR_US_64_COUNT FIELD32(0x0000ff00) 649#define TIMECSR_BEACON_EXPECT FIELD32(0x00070000) 650 651/* 652 * MACCSR0: MAC configuration register 0. 653 */ 654#define MACCSR0 0x00e0 655 656/* 657 * MACCSR1: MAC configuration register 1. 658 * KICK_RX: Kick one-shot rx in one-shot rx mode. 659 * ONESHOT_RXMODE: Enable one-shot rx mode for debugging. 660 * BBPRX_RESET_MODE: Ralink bbp rx reset mode. 661 * AUTO_TXBBP: Auto tx logic access bbp control register. 662 * AUTO_RXBBP: Auto rx logic access bbp control register. 663 * LOOPBACK: Loopback mode. 0: normal, 1: internal, 2: external, 3:rsvd. 664 * INTERSIL_IF: Intersil if calibration pin. 665 */ 666#define MACCSR1 0x00e4 667#define MACCSR1_KICK_RX FIELD32(0x00000001) 668#define MACCSR1_ONESHOT_RXMODE FIELD32(0x00000002) 669#define MACCSR1_BBPRX_RESET_MODE FIELD32(0x00000004) 670#define MACCSR1_AUTO_TXBBP FIELD32(0x00000008) 671#define MACCSR1_AUTO_RXBBP FIELD32(0x00000010) 672#define MACCSR1_LOOPBACK FIELD32(0x00000060) 673#define MACCSR1_INTERSIL_IF FIELD32(0x00000080) 674 675/* 676 * RALINKCSR: Ralink Rx auto-reset BBCR. 677 * AR_BBP_DATA#: Auto reset BBP register # data. 678 * AR_BBP_ID#: Auto reset BBP register # id. 679 */ 680#define RALINKCSR 0x00e8 681#define RALINKCSR_AR_BBP_DATA0 FIELD32(0x000000ff) 682#define RALINKCSR_AR_BBP_ID0 FIELD32(0x00007f00) 683#define RALINKCSR_AR_BBP_VALID0 FIELD32(0x00008000) 684#define RALINKCSR_AR_BBP_DATA1 FIELD32(0x00ff0000) 685#define RALINKCSR_AR_BBP_ID1 FIELD32(0x7f000000) 686#define RALINKCSR_AR_BBP_VALID1 FIELD32(0x80000000) 687 688/* 689 * BCNCSR: Beacon interval control register. 690 * CHANGE: Write one to change beacon interval. 691 * DELTATIME: The delta time value. 692 * NUM_BEACON: Number of beacon according to mode. 693 * MODE: Please refer to asic specs. 694 * PLUS: Plus or minus delta time value. 695 */ 696#define BCNCSR 0x00ec 697#define BCNCSR_CHANGE FIELD32(0x00000001) 698#define BCNCSR_DELTATIME FIELD32(0x0000001e) 699#define BCNCSR_NUM_BEACON FIELD32(0x00001fe0) 700#define BCNCSR_MODE FIELD32(0x00006000) 701#define BCNCSR_PLUS FIELD32(0x00008000) 702 703/* 704 * BBP / RF / IF Control Register. 705 */ 706 707/* 708 * BBPCSR: BBP serial control register. 709 * VALUE: Register value to program into BBP. 710 * REGNUM: Selected BBP register. 711 * BUSY: 1: asic is busy execute BBP programming. 712 * WRITE_CONTROL: 1: write BBP, 0: read BBP. 713 */ 714#define BBPCSR 0x00f0 715#define BBPCSR_VALUE FIELD32(0x000000ff) 716#define BBPCSR_REGNUM FIELD32(0x00007f00) 717#define BBPCSR_BUSY FIELD32(0x00008000) 718#define BBPCSR_WRITE_CONTROL FIELD32(0x00010000) 719 720/* 721 * RFCSR: RF serial control register. 722 * VALUE: Register value + id to program into rf/if. 723 * NUMBER_OF_BITS: Number of bits used in value (i:20, rfmd:22). 724 * IF_SELECT: Chip to program: 0: rf, 1: if. 725 * PLL_LD: Rf pll_ld status. 726 * BUSY: 1: asic is busy execute rf programming. 727 */ 728#define RFCSR 0x00f4 729#define RFCSR_VALUE FIELD32(0x00ffffff) 730#define RFCSR_NUMBER_OF_BITS FIELD32(0x1f000000) 731#define RFCSR_IF_SELECT FIELD32(0x20000000) 732#define RFCSR_PLL_LD FIELD32(0x40000000) 733#define RFCSR_BUSY FIELD32(0x80000000) 734 735/* 736 * LEDCSR: LED control register. 737 * ON_PERIOD: On period, default 70ms. 738 * OFF_PERIOD: Off period, default 30ms. 739 * LINK: 0: linkoff, 1: linkup. 740 * ACTIVITY: 0: idle, 1: active. 741 * LINK_POLARITY: 0: active low, 1: active high. 742 * ACTIVITY_POLARITY: 0: active low, 1: active high. 743 * LED_DEFAULT: LED state for "enable" 0: ON, 1: OFF. 744 */ 745#define LEDCSR 0x00f8 746#define LEDCSR_ON_PERIOD FIELD32(0x000000ff) 747#define LEDCSR_OFF_PERIOD FIELD32(0x0000ff00) 748#define LEDCSR_LINK FIELD32(0x00010000) 749#define LEDCSR_ACTIVITY FIELD32(0x00020000) 750#define LEDCSR_LINK_POLARITY FIELD32(0x00040000) 751#define LEDCSR_ACTIVITY_POLARITY FIELD32(0x00080000) 752#define LEDCSR_LED_DEFAULT FIELD32(0x00100000) 753 754/* 755 * SECCSR3: AES control register. 756 */ 757#define SECCSR3 0x00fc 758 759/* 760 * ASIC pointer information. 761 * RXPTR: Current RX ring address. 762 * TXPTR: Current Tx ring address. 763 * PRIPTR: Current Priority ring address. 764 * ATIMPTR: Current ATIM ring address. 765 */ 766#define RXPTR 0x0100 767#define TXPTR 0x0104 768#define PRIPTR 0x0108 769#define ATIMPTR 0x010c 770 771/* 772 * TXACKCSR0: TX ACK timeout. 773 */ 774#define TXACKCSR0 0x0110 775 776/* 777 * ACK timeout count registers. 778 * ACKCNT0: TX ACK timeout count. 779 * ACKCNT1: RX ACK timeout count. 780 */ 781#define ACKCNT0 0x0114 782#define ACKCNT1 0x0118 783 784/* 785 * GPIO and others. 786 */ 787 788/* 789 * GPIOCSR: GPIO control register. 790 * GPIOCSR_VALx: GPIO value 791 * GPIOCSR_DIRx: GPIO direction: 0 = output; 1 = input 792 */ 793#define GPIOCSR 0x0120 794#define GPIOCSR_VAL0 FIELD32(0x00000001) 795#define GPIOCSR_VAL1 FIELD32(0x00000002) 796#define GPIOCSR_VAL2 FIELD32(0x00000004) 797#define GPIOCSR_VAL3 FIELD32(0x00000008) 798#define GPIOCSR_VAL4 FIELD32(0x00000010) 799#define GPIOCSR_VAL5 FIELD32(0x00000020) 800#define GPIOCSR_VAL6 FIELD32(0x00000040) 801#define GPIOCSR_VAL7 FIELD32(0x00000080) 802#define GPIOCSR_DIR0 FIELD32(0x00000100) 803#define GPIOCSR_DIR1 FIELD32(0x00000200) 804#define GPIOCSR_DIR2 FIELD32(0x00000400) 805#define GPIOCSR_DIR3 FIELD32(0x00000800) 806#define GPIOCSR_DIR4 FIELD32(0x00001000) 807#define GPIOCSR_DIR5 FIELD32(0x00002000) 808#define GPIOCSR_DIR6 FIELD32(0x00004000) 809#define GPIOCSR_DIR7 FIELD32(0x00008000) 810 811/* 812 * FIFO pointer registers. 813 * FIFOCSR0: TX FIFO pointer. 814 * FIFOCSR1: RX FIFO pointer. 815 */ 816#define FIFOCSR0 0x0128 817#define FIFOCSR1 0x012c 818 819/* 820 * BCNCSR1: Tx BEACON offset time control register. 821 * PRELOAD: Beacon timer offset in units of usec. 822 * BEACON_CWMIN: 2^CwMin. 823 */ 824#define BCNCSR1 0x0130 825#define BCNCSR1_PRELOAD FIELD32(0x0000ffff) 826#define BCNCSR1_BEACON_CWMIN FIELD32(0x000f0000) 827 828/* 829 * MACCSR2: TX_PE to RX_PE turn-around time control register 830 * DELAY: RX_PE low width, in units of pci clock cycle. 831 */ 832#define MACCSR2 0x0134 833#define MACCSR2_DELAY FIELD32(0x000000ff) 834 835/* 836 * TESTCSR: TEST mode selection register. 837 */ 838#define TESTCSR 0x0138 839 840/* 841 * ARCSR2: 1 Mbps ACK/CTS PLCP. 842 */ 843#define ARCSR2 0x013c 844#define ARCSR2_SIGNAL FIELD32(0x000000ff) 845#define ARCSR2_SERVICE FIELD32(0x0000ff00) 846#define ARCSR2_LENGTH FIELD32(0xffff0000) 847 848/* 849 * ARCSR3: 2 Mbps ACK/CTS PLCP. 850 */ 851#define ARCSR3 0x0140 852#define ARCSR3_SIGNAL FIELD32(0x000000ff) 853#define ARCSR3_SERVICE FIELD32(0x0000ff00) 854#define ARCSR3_LENGTH FIELD32(0xffff0000) 855 856/* 857 * ARCSR4: 5.5 Mbps ACK/CTS PLCP. 858 */ 859#define ARCSR4 0x0144 860#define ARCSR4_SIGNAL FIELD32(0x000000ff) 861#define ARCSR4_SERVICE FIELD32(0x0000ff00) 862#define ARCSR4_LENGTH FIELD32(0xffff0000) 863 864/* 865 * ARCSR5: 11 Mbps ACK/CTS PLCP. 866 */ 867#define ARCSR5 0x0148 868#define ARCSR5_SIGNAL FIELD32(0x000000ff) 869#define ARCSR5_SERVICE FIELD32(0x0000ff00) 870#define ARCSR5_LENGTH FIELD32(0xffff0000) 871 872/* 873 * ARTCSR0: CCK ACK/CTS payload consumed time for 1/2/5.5/11 mbps. 874 */ 875#define ARTCSR0 0x014c 876#define ARTCSR0_ACK_CTS_11MBS FIELD32(0x000000ff) 877#define ARTCSR0_ACK_CTS_5_5MBS FIELD32(0x0000ff00) 878#define ARTCSR0_ACK_CTS_2MBS FIELD32(0x00ff0000) 879#define ARTCSR0_ACK_CTS_1MBS FIELD32(0xff000000) 880 881 882/* 883 * ARTCSR1: OFDM ACK/CTS payload consumed time for 6/9/12/18 mbps. 884 */ 885#define ARTCSR1 0x0150 886#define ARTCSR1_ACK_CTS_6MBS FIELD32(0x000000ff) 887#define ARTCSR1_ACK_CTS_9MBS FIELD32(0x0000ff00) 888#define ARTCSR1_ACK_CTS_12MBS FIELD32(0x00ff0000) 889#define ARTCSR1_ACK_CTS_18MBS FIELD32(0xff000000) 890 891/* 892 * ARTCSR2: OFDM ACK/CTS payload consumed time for 24/36/48/54 mbps. 893 */ 894#define ARTCSR2 0x0154 895#define ARTCSR2_ACK_CTS_24MBS FIELD32(0x000000ff) 896#define ARTCSR2_ACK_CTS_36MBS FIELD32(0x0000ff00) 897#define ARTCSR2_ACK_CTS_48MBS FIELD32(0x00ff0000) 898#define ARTCSR2_ACK_CTS_54MBS FIELD32(0xff000000) 899 900/* 901 * SECCSR1: WEP control register. 902 * KICK_ENCRYPT: Kick encryption engine, self-clear. 903 * ONE_SHOT: 0: ring mode, 1: One shot only mode. 904 * DESC_ADDRESS: Descriptor physical address of frame. 905 */ 906#define SECCSR1 0x0158 907#define SECCSR1_KICK_ENCRYPT FIELD32(0x00000001) 908#define SECCSR1_ONE_SHOT FIELD32(0x00000002) 909#define SECCSR1_DESC_ADDRESS FIELD32(0xfffffffc) 910 911/* 912 * BBPCSR1: BBP TX configuration. 913 */ 914#define BBPCSR1 0x015c 915#define BBPCSR1_CCK FIELD32(0x00000003) 916#define BBPCSR1_CCK_FLIP FIELD32(0x00000004) 917#define BBPCSR1_OFDM FIELD32(0x00030000) 918#define BBPCSR1_OFDM_FLIP FIELD32(0x00040000) 919 920/* 921 * Dual band configuration registers. 922 * DBANDCSR0: Dual band configuration register 0. 923 * DBANDCSR1: Dual band configuration register 1. 924 */ 925#define DBANDCSR0 0x0160 926#define DBANDCSR1 0x0164 927 928/* 929 * BBPPCSR: BBP Pin control register. 930 */ 931#define BBPPCSR 0x0168 932 933/* 934 * MAC special debug mode selection registers. 935 * DBGSEL0: MAC special debug mode selection register 0. 936 * DBGSEL1: MAC special debug mode selection register 1. 937 */ 938#define DBGSEL0 0x016c 939#define DBGSEL1 0x0170 940 941/* 942 * BISTCSR: BBP BIST register. 943 */ 944#define BISTCSR 0x0174 945 946/* 947 * Multicast filter registers. 948 * MCAST0: Multicast filter register 0. 949 * MCAST1: Multicast filter register 1. 950 */ 951#define MCAST0 0x0178 952#define MCAST1 0x017c 953 954/* 955 * UART registers. 956 * UARTCSR0: UART1 TX register. 957 * UARTCSR1: UART1 RX register. 958 * UARTCSR3: UART1 frame control register. 959 * UARTCSR4: UART1 buffer control register. 960 * UART2CSR0: UART2 TX register. 961 * UART2CSR1: UART2 RX register. 962 * UART2CSR3: UART2 frame control register. 963 * UART2CSR4: UART2 buffer control register. 964 */ 965#define UARTCSR0 0x0180 966#define UARTCSR1 0x0184 967#define UARTCSR3 0x0188 968#define UARTCSR4 0x018c 969#define UART2CSR0 0x0190 970#define UART2CSR1 0x0194 971#define UART2CSR3 0x0198 972#define UART2CSR4 0x019c 973 974/* 975 * BBP registers. 976 * The wordsize of the BBP is 8 bits. 977 */ 978 979/* 980 * R2: TX antenna control 981 */ 982#define BBP_R2_TX_ANTENNA FIELD8(0x03) 983#define BBP_R2_TX_IQ_FLIP FIELD8(0x04) 984 985/* 986 * R14: RX antenna control 987 */ 988#define BBP_R14_RX_ANTENNA FIELD8(0x03) 989#define BBP_R14_RX_IQ_FLIP FIELD8(0x04) 990 991/* 992 * BBP_R70 993 */ 994#define BBP_R70_JAPAN_FILTER FIELD8(0x08) 995 996/* 997 * RF registers 998 */ 999 1000/*
1001 * RF 1 1002 */ 1003#define RF1_TUNER FIELD32(0x00020000) 1004 1005/* 1006 * RF 3 1007 */ 1008#define RF3_TUNER FIELD32(0x00000100) 1009#define RF3_TXPOWER FIELD32(0x00003e00) 1010 1011/* 1012 * EEPROM content. 1013 * The wordsize of the EEPROM is 16 bits. 1014 */ 1015 1016/* 1017 * HW MAC address. 1018 */ 1019#define EEPROM_MAC_ADDR_0 0x0002 1020#define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) 1021#define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) 1022#define EEPROM_MAC_ADDR1 0x0003 1023#define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) 1024#define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) 1025#define EEPROM_MAC_ADDR_2 0x0004 1026#define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) 1027#define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) 1028 1029/* 1030 * EEPROM antenna. 1031 * ANTENNA_NUM: Number of antenna's. 1032 * TX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. 1033 * RX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. 1034 * LED_MODE: 0: default, 1: TX/RX activity,2: Single (ignore link), 3: rsvd. 1035 * DYN_TXAGC: Dynamic TX AGC control. 1036 * HARDWARE_RADIO: 1: Hardware controlled radio. Read GPIO0. 1037 * RF_TYPE: Rf_type of this adapter. 1038 */ 1039#define EEPROM_ANTENNA 0x10 1040#define EEPROM_ANTENNA_NUM FIELD16(0x0003) 1041#define EEPROM_ANTENNA_TX_DEFAULT FIELD16(0x000c) 1042#define EEPROM_ANTENNA_RX_DEFAULT FIELD16(0x0030) 1043#define EEPROM_ANTENNA_LED_MODE FIELD16(0x01c0) 1044#define EEPROM_ANTENNA_DYN_TXAGC FIELD16(0x0200) 1045#define EEPROM_ANTENNA_HARDWARE_RADIO FIELD16(0x0400) 1046#define EEPROM_ANTENNA_RF_TYPE FIELD16(0xf800) 1047 1048/* 1049 * EEPROM NIC config. 1050 * CARDBUS_ACCEL: 0: enable, 1: disable. 1051 * DYN_BBP_TUNE: 0: enable, 1: disable. 1052 * CCK_TX_POWER: CCK TX power compensation. 1053 */ 1054#define EEPROM_NIC 0x11 1055#define EEPROM_NIC_CARDBUS_ACCEL FIELD16(0x0001) 1056#define EEPROM_NIC_DYN_BBP_TUNE FIELD16(0x0002) 1057#define EEPROM_NIC_CCK_TX_POWER FIELD16(0x000c) 1058 1059/* 1060 * EEPROM geography. 1061 * GEO: Default geography setting for device. 1062 */ 1063#define EEPROM_GEOGRAPHY 0x12 1064#define EEPROM_GEOGRAPHY_GEO FIELD16(0x0f00) 1065 1066/* 1067 * EEPROM BBP. 1068 */ 1069#define EEPROM_BBP_START 0x13 1070#define EEPROM_BBP_SIZE 16 1071#define EEPROM_BBP_VALUE FIELD16(0x00ff) 1072#define EEPROM_BBP_REG_ID FIELD16(0xff00) 1073 1074/* 1075 * EEPROM TXPOWER 1076 */ 1077#define EEPROM_TXPOWER_START 0x23 1078#define EEPROM_TXPOWER_SIZE 7 1079#define EEPROM_TXPOWER_1 FIELD16(0x00ff) 1080#define EEPROM_TXPOWER_2 FIELD16(0xff00) 1081 1082/* 1083 * RSSI <-> dBm offset calibration 1084 */ 1085#define EEPROM_CALIBRATE_OFFSET 0x3e 1086#define EEPROM_CALIBRATE_OFFSET_RSSI FIELD16(0x00ff) 1087 1088/* 1089 * DMA descriptor defines. 1090 */ 1091#define TXD_DESC_SIZE (11 * sizeof(__le32)) 1092#define RXD_DESC_SIZE (11 * sizeof(__le32)) 1093 1094/* 1095 * TX descriptor format for TX, PRIO, ATIM and Beacon Ring. 1096 */ 1097 1098/* 1099 * Word0 1100 */ 1101#define TXD_W0_OWNER_NIC FIELD32(0x00000001) 1102#define TXD_W0_VALID FIELD32(0x00000002) 1103#define TXD_W0_RESULT FIELD32(0x0000001c) 1104#define TXD_W0_RETRY_COUNT FIELD32(0x000000e0) 1105#define TXD_W0_MORE_FRAG FIELD32(0x00000100) 1106#define TXD_W0_ACK FIELD32(0x00000200) 1107#define TXD_W0_TIMESTAMP FIELD32(0x00000400) 1108#define TXD_W0_OFDM FIELD32(0x00000800) 1109#define TXD_W0_CIPHER_OWNER FIELD32(0x00001000) 1110#define TXD_W0_IFS FIELD32(0x00006000) 1111#define TXD_W0_RETRY_MODE FIELD32(0x00008000) 1112#define TXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) 1113#define TXD_W0_CIPHER_ALG FIELD32(0xe0000000) 1114 1115/* 1116 * Word1 1117 */ 1118#define TXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) 1119 1120/* 1121 * Word2 1122 */ 1123#define TXD_W2_IV_OFFSET FIELD32(0x0000003f) 1124#define TXD_W2_AIFS FIELD32(0x000000c0) 1125#define TXD_W2_CWMIN FIELD32(0x00000f00) 1126#define TXD_W2_CWMAX FIELD32(0x0000f000) 1127 1128/* 1129 * Word3: PLCP information 1130 */ 1131#define TXD_W3_PLCP_SIGNAL FIELD32(0x000000ff) 1132#define TXD_W3_PLCP_SERVICE FIELD32(0x0000ff00) 1133#define TXD_W3_PLCP_LENGTH_LOW FIELD32(0x00ff0000) 1134#define TXD_W3_PLCP_LENGTH_HIGH FIELD32(0xff000000) 1135 1136/* 1137 * Word4 1138 */ 1139#define TXD_W4_IV FIELD32(0xffffffff) 1140 1141/* 1142 * Word5 1143 */ 1144#define TXD_W5_EIV FIELD32(0xffffffff) 1145 1146/* 1147 * Word6-9: Key 1148 */ 1149#define TXD_W6_KEY FIELD32(0xffffffff) 1150#define TXD_W7_KEY FIELD32(0xffffffff) 1151#define TXD_W8_KEY FIELD32(0xffffffff) 1152#define TXD_W9_KEY FIELD32(0xffffffff) 1153 1154/* 1155 * Word10 1156 */ 1157#define TXD_W10_RTS FIELD32(0x00000001) 1158#define TXD_W10_TX_RATE FIELD32(0x000000fe) 1159 1160/* 1161 * RX descriptor format for RX Ring. 1162 */ 1163 1164/* 1165 * Word0 1166 */ 1167#define RXD_W0_OWNER_NIC FIELD32(0x00000001) 1168#define RXD_W0_UNICAST_TO_ME FIELD32(0x00000002) 1169#define RXD_W0_MULTICAST FIELD32(0x00000004) 1170#define RXD_W0_BROADCAST FIELD32(0x00000008) 1171#define RXD_W0_MY_BSS FIELD32(0x00000010) 1172#define RXD_W0_CRC_ERROR FIELD32(0x00000020) 1173#define RXD_W0_OFDM FIELD32(0x00000040) 1174#define RXD_W0_PHYSICAL_ERROR FIELD32(0x00000080) 1175#define RXD_W0_CIPHER_OWNER FIELD32(0x00000100) 1176#define RXD_W0_ICV_ERROR FIELD32(0x00000200) 1177#define RXD_W0_IV_OFFSET FIELD32(0x0000fc00) 1178#define RXD_W0_DATABYTE_COUNT FIELD32(0x0fff0000) 1179#define RXD_W0_CIPHER_ALG FIELD32(0xe0000000) 1180 1181/* 1182 * Word1 1183 */ 1184#define RXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) 1185 1186/* 1187 * Word2 1188 */ 1189#define RXD_W2_SIGNAL FIELD32(0x000000ff) 1190#define RXD_W2_RSSI FIELD32(0x0000ff00) 1191#define RXD_W2_TA FIELD32(0xffff0000) 1192 1193/* 1194 * Word3 1195 */ 1196#define RXD_W3_TA FIELD32(0xffffffff) 1197 1198/* 1199 * Word4 1200 */ 1201#define RXD_W4_IV FIELD32(0xffffffff) 1202 1203/* 1204 * Word5 1205 */ 1206#define RXD_W5_EIV FIELD32(0xffffffff) 1207 1208/* 1209 * Word6-9: Key 1210 */ 1211#define RXD_W6_KEY FIELD32(0xffffffff) 1212#define RXD_W7_KEY FIELD32(0xffffffff) 1213#define RXD_W8_KEY FIELD32(0xffffffff) 1214#define RXD_W9_KEY FIELD32(0xffffffff) 1215 1216/* 1217 * Word10 1218 */ 1219#define RXD_W10_DROP FIELD32(0x00000001) 1220 1221/* 1222 * Macros for converting txpower from EEPROM to mac80211 value 1223 * and from mac80211 value to register value. 1224 */ 1225#define MIN_TXPOWER 0 1226#define MAX_TXPOWER 31 1227#define DEFAULT_TXPOWER 24 1228 1229#define TXPOWER_FROM_DEV(__txpower) \ 1230 (((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower) 1231 1232#define TXPOWER_TO_DEV(__txpower) \ 1233 clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER) 1234 1235#endif /* RT2500PCI_H */ 1236