linux/arch/blackfin/mach-bf537/boards/cm_bf537u.c
<<
>>
Prefs
   1/*
   2 * Copyright 2004-2009 Analog Devices Inc.
   3 *           2008-2009 Bluetechnix
   4 *                2005 National ICT Australia (NICTA)
   5 *                      Aidan Williams <aidan@nicta.com.au>
   6 *
   7 * Licensed under the GPL-2 or later.
   8 */
   9
  10#include <linux/device.h>
  11#include <linux/etherdevice.h>
  12#include <linux/export.h>
  13#include <linux/platform_device.h>
  14#include <linux/mtd/mtd.h>
  15#include <linux/mtd/partitions.h>
  16#include <linux/mtd/physmap.h>
  17#include <linux/spi/spi.h>
  18#include <linux/spi/flash.h>
  19#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
  20#include <linux/usb/isp1362.h>
  21#endif
  22#include <linux/ata_platform.h>
  23#include <linux/irq.h>
  24#include <linux/gpio.h>
  25#include <asm/dma.h>
  26#include <asm/bfin5xx_spi.h>
  27#include <asm/portmux.h>
  28#include <asm/dpmc.h>
  29#include <linux/spi/mmc_spi.h>
  30
  31/*
  32 * Name the Board for the /proc/cpuinfo
  33 */
  34const char bfin_board_name[] = "Bluetechnix CM BF537U";
  35
  36#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
  37/* all SPI peripherals info goes here */
  38
  39#if IS_ENABLED(CONFIG_MTD_M25P80)
  40static struct mtd_partition bfin_spi_flash_partitions[] = {
  41        {
  42                .name = "bootloader(spi)",
  43                .size = 0x00020000,
  44                .offset = 0,
  45                .mask_flags = MTD_CAP_ROM
  46        }, {
  47                .name = "linux kernel(spi)",
  48                .size = 0xe0000,
  49                .offset = 0x20000
  50        }, {
  51                .name = "file system(spi)",
  52                .size = 0x700000,
  53                .offset = 0x00100000,
  54        }
  55};
  56
  57static struct flash_platform_data bfin_spi_flash_data = {
  58        .name = "m25p80",
  59        .parts = bfin_spi_flash_partitions,
  60        .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
  61        .type = "m25p64",
  62};
  63
  64/* SPI flash chip (m25p64) */
  65static struct bfin5xx_spi_chip spi_flash_chip_info = {
  66        .enable_dma = 0,         /* use dma transfer with this chip*/
  67};
  68#endif
  69
  70#if IS_ENABLED(CONFIG_MMC_SPI)
  71static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
  72        .enable_dma = 0,
  73};
  74#endif
  75
  76static struct spi_board_info bfin_spi_board_info[] __initdata = {
  77#if IS_ENABLED(CONFIG_MTD_M25P80)
  78        {
  79                /* the modalias must be the same as spi device driver name */
  80                .modalias = "m25p80", /* Name of spi_driver for this device */
  81                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
  82                .bus_num = 0, /* Framework bus number */
  83                .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
  84                .platform_data = &bfin_spi_flash_data,
  85                .controller_data = &spi_flash_chip_info,
  86                .mode = SPI_MODE_3,
  87        },
  88#endif
  89
  90#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
  91        {
  92                .modalias = "ad183x",
  93                .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
  94                .bus_num = 0,
  95                .chip_select = 4,
  96        },
  97#endif
  98
  99#if IS_ENABLED(CONFIG_MMC_SPI)
 100        {
 101                .modalias = "mmc_spi",
 102                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 103                .bus_num = 0,
 104                .chip_select = 1,
 105                .controller_data = &mmc_spi_chip_info,
 106                .mode = SPI_MODE_3,
 107        },
 108#endif
 109};
 110
 111/* SPI (0) */
 112static struct resource bfin_spi0_resource[] = {
 113        [0] = {
 114                .start = SPI0_REGBASE,
 115                .end   = SPI0_REGBASE + 0xFF,
 116                .flags = IORESOURCE_MEM,
 117                },
 118        [1] = {
 119                .start = CH_SPI,
 120                .end   = CH_SPI,
 121                .flags = IORESOURCE_DMA,
 122        },
 123        [2] = {
 124                .start = IRQ_SPI,
 125                .end   = IRQ_SPI,
 126                .flags = IORESOURCE_IRQ,
 127        },
 128};
 129
 130/* SPI controller data */
 131static struct bfin5xx_spi_master bfin_spi0_info = {
 132        .num_chipselect = 8,
 133        .enable_dma = 1,  /* master has the ability to do dma transfer */
 134        .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 135};
 136
 137static struct platform_device bfin_spi0_device = {
 138        .name = "bfin-spi",
 139        .id = 0, /* Bus number */
 140        .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 141        .resource = bfin_spi0_resource,
 142        .dev = {
 143                .platform_data = &bfin_spi0_info, /* Passed to driver */
 144        },
 145};
 146#endif  /* spi master and devices */
 147
 148#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 149static struct platform_device rtc_device = {
 150        .name = "rtc-bfin",
 151        .id   = -1,
 152};
 153#endif
 154
 155#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 156static struct platform_device hitachi_fb_device = {
 157        .name = "hitachi-tx09",
 158};
 159#endif
 160
 161#if IS_ENABLED(CONFIG_SMC91X)
 162#include <linux/smc91x.h>
 163
 164static struct smc91x_platdata smc91x_info = {
 165        .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 166        .leda = RPC_LED_100_10,
 167        .ledb = RPC_LED_TX_RX,
 168};
 169
 170static struct resource smc91x_resources[] = {
 171        {
 172                .start = 0x20200300,
 173                .end = 0x20200300 + 16,
 174                .flags = IORESOURCE_MEM,
 175        }, {
 176                .start = IRQ_PF14,
 177                .end = IRQ_PF14,
 178                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 179                },
 180};
 181
 182static struct platform_device smc91x_device = {
 183        .name = "smc91x",
 184        .id = 0,
 185        .num_resources = ARRAY_SIZE(smc91x_resources),
 186        .resource = smc91x_resources,
 187        .dev    = {
 188                .platform_data  = &smc91x_info,
 189        },
 190};
 191#endif
 192
 193#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 194static struct resource isp1362_hcd_resources[] = {
 195        {
 196                .start = 0x20308000,
 197                .end = 0x20308000,
 198                .flags = IORESOURCE_MEM,
 199        }, {
 200                .start = 0x20308004,
 201                .end = 0x20308004,
 202                .flags = IORESOURCE_MEM,
 203        }, {
 204                .start = IRQ_PG15,
 205                .end = IRQ_PG15,
 206                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 207        },
 208};
 209
 210static struct isp1362_platform_data isp1362_priv = {
 211        .sel15Kres = 1,
 212        .clknotstop = 0,
 213        .oc_enable = 0,
 214        .int_act_high = 0,
 215        .int_edge_triggered = 0,
 216        .remote_wakeup_connected = 0,
 217        .no_power_switching = 1,
 218        .power_switching_mode = 0,
 219};
 220
 221static struct platform_device isp1362_hcd_device = {
 222        .name = "isp1362-hcd",
 223        .id = 0,
 224        .dev = {
 225                .platform_data = &isp1362_priv,
 226        },
 227        .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 228        .resource = isp1362_hcd_resources,
 229};
 230#endif
 231
 232#if IS_ENABLED(CONFIG_USB_NET2272)
 233static struct resource net2272_bfin_resources[] = {
 234        {
 235                .start = 0x20200000,
 236                .end = 0x20200000 + 0x100,
 237                .flags = IORESOURCE_MEM,
 238        }, {
 239                .start = IRQ_PH14,
 240                .end = IRQ_PH14,
 241                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 242        },
 243};
 244
 245static struct platform_device net2272_bfin_device = {
 246        .name = "net2272",
 247        .id = -1,
 248        .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 249        .resource = net2272_bfin_resources,
 250};
 251#endif
 252
 253#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 254static struct mtd_partition cm_partitions[] = {
 255        {
 256                .name   = "bootloader(nor)",
 257                .size   = 0x40000,
 258                .offset = 0,
 259        }, {
 260                .name   = "linux kernel(nor)",
 261                .size   = 0x100000,
 262                .offset = MTDPART_OFS_APPEND,
 263        }, {
 264                .name   = "file system(nor)",
 265                .size   = MTDPART_SIZ_FULL,
 266                .offset = MTDPART_OFS_APPEND,
 267        }
 268};
 269
 270static struct physmap_flash_data cm_flash_data = {
 271        .width    = 2,
 272        .parts    = cm_partitions,
 273        .nr_parts = ARRAY_SIZE(cm_partitions),
 274};
 275
 276static unsigned cm_flash_gpios[] = { GPIO_PH0 };
 277
 278static struct resource cm_flash_resource[] = {
 279        {
 280                .name  = "cfi_probe",
 281                .start = 0x20000000,
 282                .end   = 0x201fffff,
 283                .flags = IORESOURCE_MEM,
 284        }, {
 285                .start = (unsigned long)cm_flash_gpios,
 286                .end   = ARRAY_SIZE(cm_flash_gpios),
 287                .flags = IORESOURCE_IRQ,
 288        }
 289};
 290
 291static struct platform_device cm_flash_device = {
 292        .name          = "gpio-addr-flash",
 293        .id            = 0,
 294        .dev = {
 295                .platform_data = &cm_flash_data,
 296        },
 297        .num_resources = ARRAY_SIZE(cm_flash_resource),
 298        .resource      = cm_flash_resource,
 299};
 300#endif
 301
 302#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 303#ifdef CONFIG_SERIAL_BFIN_UART0
 304static struct resource bfin_uart0_resources[] = {
 305        {
 306                .start = UART0_THR,
 307                .end = UART0_GCTL+2,
 308                .flags = IORESOURCE_MEM,
 309        },
 310        {
 311                .start = IRQ_UART0_TX,
 312                .end = IRQ_UART0_TX,
 313                .flags = IORESOURCE_IRQ,
 314        },
 315        {
 316                .start = IRQ_UART0_RX,
 317                .end = IRQ_UART0_RX,
 318                .flags = IORESOURCE_IRQ,
 319        },
 320        {
 321                .start = IRQ_UART0_ERROR,
 322                .end = IRQ_UART0_ERROR,
 323                .flags = IORESOURCE_IRQ,
 324        },
 325        {
 326                .start = CH_UART0_TX,
 327                .end = CH_UART0_TX,
 328                .flags = IORESOURCE_DMA,
 329        },
 330        {
 331                .start = CH_UART0_RX,
 332                .end = CH_UART0_RX,
 333                .flags = IORESOURCE_DMA,
 334        },
 335};
 336
 337static unsigned short bfin_uart0_peripherals[] = {
 338        P_UART0_TX, P_UART0_RX, 0
 339};
 340
 341static struct platform_device bfin_uart0_device = {
 342        .name = "bfin-uart",
 343        .id = 0,
 344        .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 345        .resource = bfin_uart0_resources,
 346        .dev = {
 347                .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 348        },
 349};
 350#endif
 351#ifdef CONFIG_SERIAL_BFIN_UART1
 352static struct resource bfin_uart1_resources[] = {
 353        {
 354                .start = UART1_THR,
 355                .end = UART1_GCTL+2,
 356                .flags = IORESOURCE_MEM,
 357        },
 358        {
 359                .start = IRQ_UART1_TX,
 360                .end = IRQ_UART1_TX,
 361                .flags = IORESOURCE_IRQ,
 362        },
 363        {
 364                .start = IRQ_UART1_RX,
 365                .end = IRQ_UART1_RX,
 366                .flags = IORESOURCE_IRQ,
 367        },
 368        {
 369                .start = IRQ_UART1_ERROR,
 370                .end = IRQ_UART1_ERROR,
 371                .flags = IORESOURCE_IRQ,
 372        },
 373        {
 374                .start = CH_UART1_TX,
 375                .end = CH_UART1_TX,
 376                .flags = IORESOURCE_DMA,
 377        },
 378        {
 379                .start = CH_UART1_RX,
 380                .end = CH_UART1_RX,
 381                .flags = IORESOURCE_DMA,
 382        },
 383};
 384
 385static unsigned short bfin_uart1_peripherals[] = {
 386        P_UART1_TX, P_UART1_RX, 0
 387};
 388
 389static struct platform_device bfin_uart1_device = {
 390        .name = "bfin-uart",
 391        .id = 1,
 392        .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 393        .resource = bfin_uart1_resources,
 394        .dev = {
 395                .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 396        },
 397};
 398#endif
 399#endif
 400
 401#if IS_ENABLED(CONFIG_BFIN_SIR)
 402#ifdef CONFIG_BFIN_SIR0
 403static struct resource bfin_sir0_resources[] = {
 404        {
 405                .start = 0xFFC00400,
 406                .end = 0xFFC004FF,
 407                .flags = IORESOURCE_MEM,
 408        },
 409        {
 410                .start = IRQ_UART0_RX,
 411                .end = IRQ_UART0_RX+1,
 412                .flags = IORESOURCE_IRQ,
 413        },
 414        {
 415                .start = CH_UART0_RX,
 416                .end = CH_UART0_RX+1,
 417                .flags = IORESOURCE_DMA,
 418        },
 419};
 420static struct platform_device bfin_sir0_device = {
 421        .name = "bfin_sir",
 422        .id = 0,
 423        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 424        .resource = bfin_sir0_resources,
 425};
 426#endif
 427#ifdef CONFIG_BFIN_SIR1
 428static struct resource bfin_sir1_resources[] = {
 429        {
 430                .start = 0xFFC02000,
 431                .end = 0xFFC020FF,
 432                .flags = IORESOURCE_MEM,
 433        },
 434        {
 435                .start = IRQ_UART1_RX,
 436                .end = IRQ_UART1_RX+1,
 437                .flags = IORESOURCE_IRQ,
 438        },
 439        {
 440                .start = CH_UART1_RX,
 441                .end = CH_UART1_RX+1,
 442                .flags = IORESOURCE_DMA,
 443        },
 444};
 445static struct platform_device bfin_sir1_device = {
 446        .name = "bfin_sir",
 447        .id = 1,
 448        .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 449        .resource = bfin_sir1_resources,
 450};
 451#endif
 452#endif
 453
 454#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 455static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 456
 457static struct resource bfin_twi0_resource[] = {
 458        [0] = {
 459                .start = TWI0_REGBASE,
 460                .end   = TWI0_REGBASE,
 461                .flags = IORESOURCE_MEM,
 462        },
 463        [1] = {
 464                .start = IRQ_TWI,
 465                .end   = IRQ_TWI,
 466                .flags = IORESOURCE_IRQ,
 467        },
 468};
 469
 470static struct platform_device i2c_bfin_twi_device = {
 471        .name = "i2c-bfin-twi",
 472        .id = 0,
 473        .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 474        .resource = bfin_twi0_resource,
 475        .dev = {
 476                .platform_data = &bfin_twi0_pins,
 477        },
 478};
 479#endif
 480
 481#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 482#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 483static struct resource bfin_sport0_uart_resources[] = {
 484        {
 485                .start = SPORT0_TCR1,
 486                .end = SPORT0_MRCS3+4,
 487                .flags = IORESOURCE_MEM,
 488        },
 489        {
 490                .start = IRQ_SPORT0_RX,
 491                .end = IRQ_SPORT0_RX+1,
 492                .flags = IORESOURCE_IRQ,
 493        },
 494        {
 495                .start = IRQ_SPORT0_ERROR,
 496                .end = IRQ_SPORT0_ERROR,
 497                .flags = IORESOURCE_IRQ,
 498        },
 499};
 500
 501static unsigned short bfin_sport0_peripherals[] = {
 502        P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 503        P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
 504};
 505
 506static struct platform_device bfin_sport0_uart_device = {
 507        .name = "bfin-sport-uart",
 508        .id = 0,
 509        .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
 510        .resource = bfin_sport0_uart_resources,
 511        .dev = {
 512                .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
 513        },
 514};
 515#endif
 516#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 517static struct resource bfin_sport1_uart_resources[] = {
 518        {
 519                .start = SPORT1_TCR1,
 520                .end = SPORT1_MRCS3+4,
 521                .flags = IORESOURCE_MEM,
 522        },
 523        {
 524                .start = IRQ_SPORT1_RX,
 525                .end = IRQ_SPORT1_RX+1,
 526                .flags = IORESOURCE_IRQ,
 527        },
 528        {
 529                .start = IRQ_SPORT1_ERROR,
 530                .end = IRQ_SPORT1_ERROR,
 531                .flags = IORESOURCE_IRQ,
 532        },
 533};
 534
 535static unsigned short bfin_sport1_peripherals[] = {
 536        P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 537        P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
 538};
 539
 540static struct platform_device bfin_sport1_uart_device = {
 541        .name = "bfin-sport-uart",
 542        .id = 1,
 543        .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
 544        .resource = bfin_sport1_uart_resources,
 545        .dev = {
 546                .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
 547        },
 548};
 549#endif
 550#endif
 551
 552#if IS_ENABLED(CONFIG_BFIN_MAC)
 553#include <linux/bfin_mac.h>
 554static const unsigned short bfin_mac_peripherals[] = P_MII0;
 555
 556static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 557        {
 558                .addr = 1,
 559                .irq = IRQ_MAC_PHYINT,
 560        },
 561};
 562
 563static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
 564        .phydev_number = 1,
 565        .phydev_data = bfin_phydev_data,
 566        .phy_mode = PHY_INTERFACE_MODE_MII,
 567        .mac_peripherals = bfin_mac_peripherals,
 568};
 569
 570static struct platform_device bfin_mii_bus = {
 571        .name = "bfin_mii_bus",
 572        .dev = {
 573                .platform_data = &bfin_mii_bus_data,
 574        }
 575};
 576
 577static struct platform_device bfin_mac_device = {
 578        .name = "bfin_mac",
 579        .dev = {
 580                .platform_data = &bfin_mii_bus,
 581        }
 582};
 583#endif
 584
 585#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 586#define PATA_INT        IRQ_PF14
 587
 588static struct pata_platform_info bfin_pata_platform_data = {
 589        .ioport_shift = 2,
 590};
 591
 592static struct resource bfin_pata_resources[] = {
 593        {
 594                .start = 0x2030C000,
 595                .end = 0x2030C01F,
 596                .flags = IORESOURCE_MEM,
 597        },
 598        {
 599                .start = 0x2030D018,
 600                .end = 0x2030D01B,
 601                .flags = IORESOURCE_MEM,
 602        },
 603        {
 604                .start = PATA_INT,
 605                .end = PATA_INT,
 606                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 607        },
 608};
 609
 610static struct platform_device bfin_pata_device = {
 611        .name = "pata_platform",
 612        .id = -1,
 613        .num_resources = ARRAY_SIZE(bfin_pata_resources),
 614        .resource = bfin_pata_resources,
 615        .dev = {
 616                .platform_data = &bfin_pata_platform_data,
 617        }
 618};
 619#endif
 620
 621static const unsigned int cclk_vlev_datasheet[] =
 622{
 623        VRPAIR(VLEV_085, 250000000),
 624        VRPAIR(VLEV_090, 376000000),
 625        VRPAIR(VLEV_095, 426000000),
 626        VRPAIR(VLEV_100, 426000000),
 627        VRPAIR(VLEV_105, 476000000),
 628        VRPAIR(VLEV_110, 476000000),
 629        VRPAIR(VLEV_115, 476000000),
 630        VRPAIR(VLEV_120, 500000000),
 631        VRPAIR(VLEV_125, 533000000),
 632        VRPAIR(VLEV_130, 600000000),
 633};
 634
 635static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 636        .tuple_tab = cclk_vlev_datasheet,
 637        .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 638        .vr_settling_time = 25 /* us */,
 639};
 640
 641static struct platform_device bfin_dpmc = {
 642        .name = "bfin dpmc",
 643        .dev = {
 644                .platform_data = &bfin_dmpc_vreg_data,
 645        },
 646};
 647
 648static struct platform_device *cm_bf537u_devices[] __initdata = {
 649
 650        &bfin_dpmc,
 651
 652#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 653        &hitachi_fb_device,
 654#endif
 655
 656#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 657        &rtc_device,
 658#endif
 659
 660#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 661#ifdef CONFIG_SERIAL_BFIN_UART0
 662        &bfin_uart0_device,
 663#endif
 664#ifdef CONFIG_SERIAL_BFIN_UART1
 665        &bfin_uart1_device,
 666#endif
 667#endif
 668
 669#if IS_ENABLED(CONFIG_BFIN_SIR)
 670#ifdef CONFIG_BFIN_SIR0
 671        &bfin_sir0_device,
 672#endif
 673#ifdef CONFIG_BFIN_SIR1
 674        &bfin_sir1_device,
 675#endif
 676#endif
 677
 678#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 679        &i2c_bfin_twi_device,
 680#endif
 681
 682#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 683#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 684        &bfin_sport0_uart_device,
 685#endif
 686#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 687        &bfin_sport1_uart_device,
 688#endif
 689#endif
 690
 691#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 692        &isp1362_hcd_device,
 693#endif
 694
 695#if IS_ENABLED(CONFIG_SMC91X)
 696        &smc91x_device,
 697#endif
 698
 699#if IS_ENABLED(CONFIG_BFIN_MAC)
 700        &bfin_mii_bus,
 701        &bfin_mac_device,
 702#endif
 703
 704#if IS_ENABLED(CONFIG_USB_NET2272)
 705        &net2272_bfin_device,
 706#endif
 707
 708#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 709        &bfin_spi0_device,
 710#endif
 711
 712#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 713        &bfin_pata_device,
 714#endif
 715
 716#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 717        &cm_flash_device,
 718#endif
 719};
 720
 721static int __init net2272_init(void)
 722{
 723#if IS_ENABLED(CONFIG_USB_NET2272)
 724        int ret;
 725
 726        ret = gpio_request(GPIO_PH15, driver_name);
 727        if (ret)
 728                return ret;
 729
 730        ret = gpio_request(GPIO_PH13, "net2272");
 731        if (ret) {
 732                gpio_free(GPIO_PH15);
 733                return ret;
 734        }
 735
 736        /* Set PH15 Low make /AMS2 work properly */
 737        gpio_direction_output(GPIO_PH15, 0);
 738
 739        /* enable CLKBUF output */
 740        bfin_write_VR_CTL(bfin_read_VR_CTL() | CLKBUFOE);
 741
 742        /* Reset the USB chip */
 743        gpio_direction_output(GPIO_PH13, 0);
 744        mdelay(2);
 745        gpio_set_value(GPIO_PH13, 1);
 746#endif
 747
 748        return 0;
 749}
 750
 751static int __init cm_bf537u_init(void)
 752{
 753        printk(KERN_INFO "%s(): registering device resources\n", __func__);
 754        platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
 755#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 756        spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 757#endif
 758
 759#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 760        irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 761#endif
 762
 763        if (net2272_init())
 764                pr_warning("unable to configure net2272; it probably won't work\n");
 765
 766        return 0;
 767}
 768
 769arch_initcall(cm_bf537u_init);
 770
 771static struct platform_device *cm_bf537u_early_devices[] __initdata = {
 772#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 773#ifdef CONFIG_SERIAL_BFIN_UART0
 774        &bfin_uart0_device,
 775#endif
 776#ifdef CONFIG_SERIAL_BFIN_UART1
 777        &bfin_uart1_device,
 778#endif
 779#endif
 780
 781#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
 782#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 783        &bfin_sport0_uart_device,
 784#endif
 785#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 786        &bfin_sport1_uart_device,
 787#endif
 788#endif
 789};
 790
 791void __init native_machine_early_platform_add_devices(void)
 792{
 793        printk(KERN_INFO "register early platform devices\n");
 794        early_platform_add_devices(cm_bf537u_early_devices,
 795                ARRAY_SIZE(cm_bf537u_early_devices));
 796}
 797
 798int bfin_get_ether_addr(char *addr)
 799{
 800        return 1;
 801}
 802EXPORT_SYMBOL(bfin_get_ether_addr);
 803