1/* 2 * Blackfin On-Chip SPI Driver 3 * 4 * Copyright 2004-2008 Analog Devices Inc. 5 * 6 * Licensed under the GPL-2 or later. 7 */ 8 9#ifndef _SPI_CHANNEL_H_ 10#define _SPI_CHANNEL_H_ 11 12#define MIN_SPI_BAUD_VAL 2 13 14#define BIT_CTL_ENABLE 0x4000 15#define BIT_CTL_OPENDRAIN 0x2000 16#define BIT_CTL_MASTER 0x1000 17#define BIT_CTL_CPOL 0x0800 18#define BIT_CTL_CPHA 0x0400 19#define BIT_CTL_LSBF 0x0200 20#define BIT_CTL_WORDSIZE 0x0100 21#define BIT_CTL_EMISO 0x0020 22#define BIT_CTL_PSSE 0x0010 23#define BIT_CTL_GM 0x0008 24#define BIT_CTL_SZ 0x0004 25#define BIT_CTL_RXMOD 0x0000 26#define BIT_CTL_TXMOD 0x0001 27#define BIT_CTL_TIMOD_DMA_TX 0x0003 28#define BIT_CTL_TIMOD_DMA_RX 0x0002 29#define BIT_CTL_SENDOPT 0x0004 30#define BIT_CTL_TIMOD 0x0003 31 32#define BIT_STAT_SPIF 0x0001 33#define BIT_STAT_MODF 0x0002 34#define BIT_STAT_TXE 0x0004 35#define BIT_STAT_TXS 0x0008 36#define BIT_STAT_RBSY 0x0010 37#define BIT_STAT_RXS 0x0020 38#define BIT_STAT_TXCOL 0x0040 39#define BIT_STAT_CLR 0xFFFF 40 41#define BIT_STU_SENDOVER 0x0001 42#define BIT_STU_RECVFULL 0x0020 43 44/* 45 * All Blackfin system MMRs are padded to 32bits even if the register 46 * itself is only 16bits. So use a helper macro to streamline this. 47 */ 48#define __BFP(m) u16 m; u16 __pad_##m 49 50/* 51 * bfin spi registers layout 52 */ 53struct bfin_spi_regs { 54 __BFP(ctl); 55 __BFP(flg); 56 __BFP(stat); 57 __BFP(tdbr); 58 __BFP(rdbr); 59 __BFP(baud); 60 __BFP(shadow); 61}; 62 63#undef __BFP 64 65#define MAX_CTRL_CS 8 /* cs in spi controller */ 66 67/* device.platform_data for SSP controller devices */ 68struct bfin5xx_spi_master { 69 u16 num_chipselect; 70 u8 enable_dma; 71 u16 pin_req[7]; 72}; 73 74/* spi_board_info.controller_data for SPI slave devices, 75 * copied to spi_device.platform_data ... mostly for dma tuning 76 */ 77struct bfin5xx_spi_chip { 78 u16 ctl_reg; 79 u8 enable_dma; 80 u16 cs_chg_udelay; /* Some devices require 16-bit delays */ 81 /* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */ 82 u16 idle_tx_val; 83 u8 pio_interrupt; /* Enable spi data irq */ 84}; 85 86#endif /* _SPI_CHANNEL_H_ */ 87