linux/arch/blackfin/mach-bf537/boards/tcm_bf537.c
<<
>>
Prefs
   1/*
   2 * Copyright 2004-2009 Analog Devices Inc.
   3 *           2008-2009 Bluetechnix
   4 *                2005 National ICT Australia (NICTA)
   5 *                      Aidan Williams <aidan@nicta.com.au>
   6 *
   7 * Licensed under the GPL-2 or later.
   8 */
   9
  10#include <linux/device.h>
  11#include <linux/etherdevice.h>
  12#include <linux/export.h>
  13#include <linux/platform_device.h>
  14#include <linux/mtd/mtd.h>
  15#include <linux/mtd/partitions.h>
  16#include <linux/mtd/physmap.h>
  17#include <linux/spi/spi.h>
  18#include <linux/spi/flash.h>
  19#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
  20#include <linux/usb/isp1362.h>
  21#endif
  22#include <linux/ata_platform.h>
  23#include <linux/irq.h>
  24#include <linux/gpio.h>
  25#include <asm/dma.h>
  26#include <asm/bfin5xx_spi.h>
  27#include <asm/portmux.h>
  28#include <asm/dpmc.h>
  29#include <linux/spi/mmc_spi.h>
  30
  31/*
  32 * Name the Board for the /proc/cpuinfo
  33 */
  34const char bfin_board_name[] = "Bluetechnix TCM BF537";
  35
  36#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
  37/* all SPI peripherals info goes here */
  38
  39#if IS_ENABLED(CONFIG_MTD_M25P80)
  40static struct mtd_partition bfin_spi_flash_partitions[] = {
  41        {
  42                .name = "bootloader(spi)",
  43                .size = 0x00020000,
  44                .offset = 0,
  45                .mask_flags = MTD_CAP_ROM
  46        }, {
  47                .name = "linux kernel(spi)",
  48                .size = 0xe0000,
  49                .offset = 0x20000
  50        }, {
  51                .name = "file system(spi)",
  52                .size = 0x700000,
  53                .offset = 0x00100000,
  54        }
  55};
  56
  57static struct flash_platform_data bfin_spi_flash_data = {
  58        .name = "m25p80",
  59        .parts = bfin_spi_flash_partitions,
  60        .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
  61        .type = "m25p64",
  62};
  63
  64/* SPI flash chip (m25p64) */
  65static struct bfin5xx_spi_chip spi_flash_chip_info = {
  66        .enable_dma = 0,         /* use dma transfer with this chip*/
  67};
  68#endif
  69
  70#if IS_ENABLED(CONFIG_MMC_SPI)
  71static struct bfin5xx_spi_chip mmc_spi_chip_info = {
  72        .enable_dma = 0,
  73};
  74#endif
  75
  76static struct spi_board_info bfin_spi_board_info[] __initdata = {
  77#if IS_ENABLED(CONFIG_MTD_M25P80)
  78        {
  79                /* the modalias must be the same as spi device driver name */
  80                .modalias = "m25p80", /* Name of spi_driver for this device */
  81                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
  82                .bus_num = 0, /* Framework bus number */
  83                .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
  84                .platform_data = &bfin_spi_flash_data,
  85                .controller_data = &spi_flash_chip_info,
  86                .mode = SPI_MODE_3,
  87        },
  88#endif
  89
  90#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
  91        {
  92                .modalias = "ad183x",
  93                .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
  94                .bus_num = 0,
  95                .chip_select = 4,
  96        },
  97#endif
  98
  99#if IS_ENABLED(CONFIG_MMC_SPI)
 100        {
 101                .modalias = "mmc_spi",
 102                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 103                .bus_num = 0,
 104                .chip_select = 1,
 105                .controller_data = &mmc_spi_chip_info,
 106                .mode = SPI_MODE_3,
 107        },
 108#endif
 109};
 110
 111/* SPI (0) */
 112static struct resource bfin_spi0_resource[] = {
 113        [0] = {
 114                .start = SPI0_REGBASE,
 115                .end   = SPI0_REGBASE + 0xFF,
 116                .flags = IORESOURCE_MEM,
 117                },
 118        [1] = {
 119                .start = CH_SPI,
 120                .end   = CH_SPI,
 121                .flags = IORESOURCE_DMA,
 122        },
 123        [2] = {
 124                .start = IRQ_SPI,
 125                .end   = IRQ_SPI,
 126                .flags = IORESOURCE_IRQ,
 127        }
 128};
 129
 130/* SPI controller data */
 131static struct bfin5xx_spi_master bfin_spi0_info = {
 132        .num_chipselect = 8,
 133        .enable_dma = 1,  /* master has the ability to do dma transfer */
 134        .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 135};
 136
 137static struct platform_device bfin_spi0_device = {
 138        .name = "bfin-spi",
 139        .id = 0, /* Bus number */
 140        .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 141        .resource = bfin_spi0_resource,
 142        .dev = {
 143                .platform_data = &bfin_spi0_info, /* Passed to driver */
 144        },
 145};
 146#endif  /* spi master and devices */
 147
 148#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 149static struct platform_device rtc_device = {
 150        .name = "rtc-bfin",
 151        .id   = -1,
 152};
 153#endif
 154
 155#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 156static struct platform_device hitachi_fb_device = {
 157        .name = "hitachi-tx09",
 158};
 159#endif
 160
 161#if IS_ENABLED(CONFIG_SMC91X)
 162#include <linux/smc91x.h>
 163
 164static struct smc91x_platdata smc91x_info = {
 165        .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 166        .leda = RPC_LED_100_10,
 167        .ledb = RPC_LED_TX_RX,
 168};
 169
 170static struct resource smc91x_resources[] = {
 171        {
 172                .start = 0x20200300,
 173                .end = 0x20200300 + 16,
 174                .flags = IORESOURCE_MEM,
 175        }, {
 176                .start = IRQ_PF14,
 177                .end = IRQ_PF14,
 178                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 179                },
 180};
 181
 182static struct platform_device smc91x_device = {
 183        .name = "smc91x",
 184        .id = 0,
 185        .num_resources = ARRAY_SIZE(smc91x_resources),
 186        .resource = smc91x_resources,
 187        .dev    = {
 188                .platform_data  = &smc91x_info,
 189        },
 190};
 191#endif
 192
 193#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 194static struct resource isp1362_hcd_resources[] = {
 195        {
 196                .start = 0x20308000,
 197                .end = 0x20308000,
 198                .flags = IORESOURCE_MEM,
 199        }, {
 200                .start = 0x20308004,
 201                .end = 0x20308004,
 202                .flags = IORESOURCE_MEM,
 203        }, {
 204                .start = IRQ_PG15,
 205                .end = IRQ_PG15,
 206                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 207        },
 208};
 209
 210static struct isp1362_platform_data isp1362_priv = {
 211        .sel15Kres = 1,
 212        .clknotstop = 0,
 213        .oc_enable = 0,
 214        .int_act_high = 0,
 215        .int_edge_triggered = 0,
 216        .remote_wakeup_connected = 0,
 217        .no_power_switching = 1,
 218        .power_switching_mode = 0,
 219};
 220
 221static struct platform_device isp1362_hcd_device = {
 222        .name = "isp1362-hcd",
 223        .id = 0,
 224        .dev = {
 225                .platform_data = &isp1362_priv,
 226        },
 227        .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 228        .resource = isp1362_hcd_resources,
 229};
 230#endif
 231
 232#if IS_ENABLED(CONFIG_USB_NET2272)
 233static struct resource net2272_bfin_resources[] = {
 234        {
 235                .start = 0x20300000,
 236                .end = 0x20300000 + 0x100,
 237                .flags = IORESOURCE_MEM,
 238        }, {
 239                .start = IRQ_PG13,
 240                .end = IRQ_PG13,
 241                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 242        },
 243};
 244
 245static struct platform_device net2272_bfin_device = {
 246        .name = "net2272",
 247        .id = -1,
 248        .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 249        .resource = net2272_bfin_resources,
 250};
 251#endif
 252
 253#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 254static struct mtd_partition cm_partitions[] = {
 255        {
 256                .name   = "bootloader(nor)",
 257                .size   = 0x40000,
 258                .offset = 0,
 259        }, {
 260                .name   = "linux kernel(nor)",
 261                .size   = 0x100000,
 262                .offset = MTDPART_OFS_APPEND,
 263        }, {
 264                .name   = "file system(nor)",
 265                .size   = MTDPART_SIZ_FULL,
 266                .offset = MTDPART_OFS_APPEND,
 267        }
 268};
 269
 270static struct physmap_flash_data cm_flash_data = {
 271        .width    = 2,
 272        .parts    = cm_partitions,
 273        .nr_parts = ARRAY_SIZE(cm_partitions),
 274};
 275
 276static unsigned cm_flash_gpios[] = { GPIO_PF4, GPIO_PF5 };
 277
 278static struct resource cm_flash_resource[] = {
 279        {
 280                .name  = "cfi_probe",
 281                .start = 0x20000000,
 282                .end   = 0x201fffff,
 283                .flags = IORESOURCE_MEM,
 284        }, {
 285                .start = (unsigned long)cm_flash_gpios,
 286                .end   = ARRAY_SIZE(cm_flash_gpios),
 287                .flags = IORESOURCE_IRQ,
 288        }
 289};
 290
 291static struct platform_device cm_flash_device = {
 292        .name          = "gpio-addr-flash",
 293        .id            = 0,
 294        .dev = {
 295                .platform_data = &cm_flash_data,
 296        },
 297        .num_resources = ARRAY_SIZE(cm_flash_resource),
 298        .resource      = cm_flash_resource,
 299};
 300#endif
 301
 302#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 303#ifdef CONFIG_SERIAL_BFIN_UART0
 304static struct resource bfin_uart0_resources[] = {
 305        {
 306                .start = UART0_THR,
 307                .end = UART0_GCTL+2,
 308                .flags = IORESOURCE_MEM,
 309        },
 310        {
 311                .start = IRQ_UART0_TX,
 312                .end = IRQ_UART0_TX,
 313                .flags = IORESOURCE_IRQ,
 314        },
 315        {
 316                .start = IRQ_UART0_RX,
 317                .end = IRQ_UART0_RX,
 318                .flags = IORESOURCE_IRQ,
 319        },
 320        {
 321                .start = IRQ_UART0_ERROR,
 322                .end = IRQ_UART0_ERROR,
 323                .flags = IORESOURCE_IRQ,
 324        },
 325        {
 326                .start = CH_UART0_TX,
 327                .end = CH_UART0_TX,
 328                .flags = IORESOURCE_DMA,
 329        },
 330        {
 331                .start = CH_UART0_RX,
 332                .end = CH_UART0_RX,
 333                .flags = IORESOURCE_DMA,
 334        },
 335};
 336
 337static unsigned short bfin_uart0_peripherals[] = {
 338        P_UART0_TX, P_UART0_RX, 0
 339};
 340
 341static struct platform_device bfin_uart0_device = {
 342        .name = "bfin-uart",
 343        .id = 0,
 344        .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 345        .resource = bfin_uart0_resources,
 346        .dev = {
 347                .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 348        },
 349};
 350#endif
 351#ifdef CONFIG_SERIAL_BFIN_UART1
 352static struct resource bfin_uart1_resources[] = {
 353        {
 354                .start = UART1_THR,
 355                .end = UART1_GCTL+2,
 356                .flags = IORESOURCE_MEM,
 357        },
 358        {
 359                .start = IRQ_UART1_TX,
 360                .end = IRQ_UART1_TX,
 361                .flags = IORESOURCE_IRQ,
 362        },
 363        {
 364                .start = IRQ_UART1_RX,
 365                .end = IRQ_UART1_RX,
 366                .flags = IORESOURCE_IRQ,
 367        },
 368        {
 369                .start = IRQ_UART1_ERROR,
 370                .end = IRQ_UART1_ERROR,
 371                .flags = IORESOURCE_IRQ,
 372        },
 373        {
 374                .start = CH_UART1_TX,
 375                .end = CH_UART1_TX,
 376                .flags = IORESOURCE_DMA,
 377        },
 378        {
 379                .start = CH_UART1_RX,
 380                .end = CH_UART1_RX,
 381                .flags = IORESOURCE_DMA,
 382        },
 383};
 384
 385static unsigned short bfin_uart1_peripherals[] = {
 386        P_UART1_TX, P_UART1_RX, 0
 387};
 388
 389static struct platform_device bfin_uart1_device = {
 390        .name = "bfin-uart",
 391        .id = 1,
 392        .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 393        .resource = bfin_uart1_resources,
 394        .dev = {
 395                .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 396        },
 397};
 398#endif
 399#endif
 400
 401#if IS_ENABLED(CONFIG_BFIN_SIR)
 402#ifdef CONFIG_BFIN_SIR0
 403static struct resource bfin_sir0_resources[] = {
 404        {
 405                .start = 0xFFC00400,
 406                .end = 0xFFC004FF,
 407                .flags = IORESOURCE_MEM,
 408        },
 409        {
 410                .start = IRQ_UART0_RX,
 411                .end = IRQ_UART0_RX+1,
 412                .flags = IORESOURCE_IRQ,
 413        },
 414        {
 415                .start = CH_UART0_RX,
 416                .end = CH_UART0_RX+1,
 417                .flags = IORESOURCE_DMA,
 418        },
 419};
 420
 421static struct platform_device bfin_sir0_device = {
 422        .name = "bfin_sir",
 423        .id = 0,
 424        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 425        .resource = bfin_sir0_resources,
 426};
 427#endif
 428#ifdef CONFIG_BFIN_SIR1
 429static struct resource bfin_sir1_resources[] = {
 430        {
 431                .start = 0xFFC02000,
 432                .end = 0xFFC020FF,
 433                .flags = IORESOURCE_MEM,
 434        },
 435        {
 436                .start = IRQ_UART1_RX,
 437                .end = IRQ_UART1_RX+1,
 438                .flags = IORESOURCE_IRQ,
 439        },
 440        {
 441                .start = CH_UART1_RX,
 442                .end = CH_UART1_RX+1,
 443                .flags = IORESOURCE_DMA,
 444        },
 445};
 446
 447static struct platform_device bfin_sir1_device = {
 448        .name = "bfin_sir",
 449        .id = 1,
 450        .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 451        .resource = bfin_sir1_resources,
 452};
 453#endif
 454#endif
 455
 456#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 457static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
 458
 459static struct resource bfin_twi0_resource[] = {
 460        [0] = {
 461                .start = TWI0_REGBASE,
 462                .end   = TWI0_REGBASE,
 463                .flags = IORESOURCE_MEM,
 464        },
 465        [1] = {
 466                .start = IRQ_TWI,
 467                .end   = IRQ_TWI,
 468                .flags = IORESOURCE_IRQ,
 469        },
 470};
 471
 472static struct platform_device i2c_bfin_twi_device = {
 473        .name = "i2c-bfin-twi",
 474        .id = 0,
 475        .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 476        .resource = bfin_twi0_resource,
 477        .dev = {
 478                .platform_data = &bfin_twi0_pins,
 479        },
 480};
 481#endif
 482
 483#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 484#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 485static struct resource bfin_sport0_uart_resources[] = {
 486        {
 487                .start = SPORT0_TCR1,
 488                .end = SPORT0_MRCS3+4,
 489                .flags = IORESOURCE_MEM,
 490        },
 491        {
 492                .start = IRQ_SPORT0_RX,
 493                .end = IRQ_SPORT0_RX+1,
 494                .flags = IORESOURCE_IRQ,
 495        },
 496        {
 497                .start = IRQ_SPORT0_ERROR,
 498                .end = IRQ_SPORT0_ERROR,
 499                .flags = IORESOURCE_IRQ,
 500        },
 501};
 502
 503static unsigned short bfin_sport0_peripherals[] = {
 504        P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 505        P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
 506};
 507
 508static struct platform_device bfin_sport0_uart_device = {
 509        .name = "bfin-sport-uart",
 510        .id = 0,
 511        .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
 512        .resource = bfin_sport0_uart_resources,
 513        .dev = {
 514                .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
 515        },
 516};
 517#endif
 518#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 519static struct resource bfin_sport1_uart_resources[] = {
 520        {
 521                .start = SPORT1_TCR1,
 522                .end = SPORT1_MRCS3+4,
 523                .flags = IORESOURCE_MEM,
 524        },
 525        {
 526                .start = IRQ_SPORT1_RX,
 527                .end = IRQ_SPORT1_RX+1,
 528                .flags = IORESOURCE_IRQ,
 529        },
 530        {
 531                .start = IRQ_SPORT1_ERROR,
 532                .end = IRQ_SPORT1_ERROR,
 533                .flags = IORESOURCE_IRQ,
 534        },
 535};
 536
 537static unsigned short bfin_sport1_peripherals[] = {
 538        P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 539        P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
 540};
 541
 542static struct platform_device bfin_sport1_uart_device = {
 543        .name = "bfin-sport-uart",
 544        .id = 1,
 545        .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
 546        .resource = bfin_sport1_uart_resources,
 547        .dev = {
 548                .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
 549        },
 550};
 551#endif
 552#endif
 553
 554#if IS_ENABLED(CONFIG_BFIN_MAC)
 555#include <linux/bfin_mac.h>
 556static const unsigned short bfin_mac_peripherals[] = P_MII0;
 557
 558static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 559        {
 560                .addr = 1,
 561                .irq = IRQ_MAC_PHYINT,
 562        },
 563};
 564
 565static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
 566        .phydev_number = 1,
 567        .phydev_data = bfin_phydev_data,
 568        .phy_mode = PHY_INTERFACE_MODE_MII,
 569        .mac_peripherals = bfin_mac_peripherals,
 570};
 571
 572static struct platform_device bfin_mii_bus = {
 573        .name = "bfin_mii_bus",
 574        .dev = {
 575                .platform_data = &bfin_mii_bus_data,
 576        }
 577};
 578
 579static struct platform_device bfin_mac_device = {
 580        .name = "bfin_mac",
 581        .dev = {
 582                .platform_data = &bfin_mii_bus,
 583        }
 584};
 585#endif
 586
 587#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 588#define PATA_INT        IRQ_PF14
 589
 590static struct pata_platform_info bfin_pata_platform_data = {
 591        .ioport_shift = 2,
 592};
 593
 594static struct resource bfin_pata_resources[] = {
 595        {
 596                .start = 0x2030C000,
 597                .end = 0x2030C01F,
 598                .flags = IORESOURCE_MEM,
 599        },
 600        {
 601                .start = 0x2030D018,
 602                .end = 0x2030D01B,
 603                .flags = IORESOURCE_MEM,
 604        },
 605        {
 606                .start = PATA_INT,
 607                .end = PATA_INT,
 608                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 609        },
 610};
 611
 612static struct platform_device bfin_pata_device = {
 613        .name = "pata_platform",
 614        .id = -1,
 615        .num_resources = ARRAY_SIZE(bfin_pata_resources),
 616        .resource = bfin_pata_resources,
 617        .dev = {
 618                .platform_data = &bfin_pata_platform_data,
 619        }
 620};
 621#endif
 622
 623static const unsigned int cclk_vlev_datasheet[] =
 624{
 625        VRPAIR(VLEV_085, 250000000),
 626        VRPAIR(VLEV_090, 376000000),
 627        VRPAIR(VLEV_095, 426000000),
 628        VRPAIR(VLEV_100, 426000000),
 629        VRPAIR(VLEV_105, 476000000),
 630        VRPAIR(VLEV_110, 476000000),
 631        VRPAIR(VLEV_115, 476000000),
 632        VRPAIR(VLEV_120, 500000000),
 633        VRPAIR(VLEV_125, 533000000),
 634        VRPAIR(VLEV_130, 600000000),
 635};
 636
 637static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 638        .tuple_tab = cclk_vlev_datasheet,
 639        .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 640        .vr_settling_time = 25 /* us */,
 641};
 642
 643static struct platform_device bfin_dpmc = {
 644        .name = "bfin dpmc",
 645        .dev = {
 646                .platform_data = &bfin_dmpc_vreg_data,
 647        },
 648};
 649
 650static struct platform_device *cm_bf537_devices[] __initdata = {
 651
 652        &bfin_dpmc,
 653
 654#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 655        &hitachi_fb_device,
 656#endif
 657
 658#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 659        &rtc_device,
 660#endif
 661
 662#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 663#ifdef CONFIG_SERIAL_BFIN_UART0
 664        &bfin_uart0_device,
 665#endif
 666#ifdef CONFIG_SERIAL_BFIN_UART1
 667        &bfin_uart1_device,
 668#endif
 669#endif
 670
 671#if IS_ENABLED(CONFIG_BFIN_SIR)
 672#ifdef CONFIG_BFIN_SIR0
 673        &bfin_sir0_device,
 674#endif
 675#ifdef CONFIG_BFIN_SIR1
 676        &bfin_sir1_device,
 677#endif
 678#endif
 679
 680#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 681        &i2c_bfin_twi_device,
 682#endif
 683
 684#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 685#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 686        &bfin_sport0_uart_device,
 687#endif
 688#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 689        &bfin_sport1_uart_device,
 690#endif
 691#endif
 692
 693#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 694        &isp1362_hcd_device,
 695#endif
 696
 697#if IS_ENABLED(CONFIG_SMC91X)
 698        &smc91x_device,
 699#endif
 700
 701#if IS_ENABLED(CONFIG_BFIN_MAC)
 702        &bfin_mii_bus,
 703        &bfin_mac_device,
 704#endif
 705
 706#if IS_ENABLED(CONFIG_USB_NET2272)
 707        &net2272_bfin_device,
 708#endif
 709
 710#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 711        &bfin_spi0_device,
 712#endif
 713
 714#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 715        &bfin_pata_device,
 716#endif
 717
 718#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 719        &cm_flash_device,
 720#endif
 721};
 722
 723static int __init net2272_init(void)
 724{
 725#if IS_ENABLED(CONFIG_USB_NET2272)
 726        int ret;
 727
 728        ret = gpio_request(GPIO_PG14, "net2272");
 729        if (ret)
 730                return ret;
 731
 732        /* Reset USB Chip, PG14 */
 733        gpio_direction_output(GPIO_PG14, 0);
 734        mdelay(2);
 735        gpio_set_value(GPIO_PG14, 1);
 736#endif
 737
 738        return 0;
 739}
 740
 741static int __init tcm_bf537_init(void)
 742{
 743        printk(KERN_INFO "%s(): registering device resources\n", __func__);
 744        platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
 745#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 746        spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 747#endif
 748
 749#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 750        irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 751#endif
 752
 753        if (net2272_init())
 754                pr_warning("unable to configure net2272; it probably won't work\n");
 755
 756        return 0;
 757}
 758
 759arch_initcall(tcm_bf537_init);
 760
 761static struct platform_device *cm_bf537_early_devices[] __initdata = {
 762#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 763#ifdef CONFIG_SERIAL_BFIN_UART0
 764        &bfin_uart0_device,
 765#endif
 766#ifdef CONFIG_SERIAL_BFIN_UART1
 767        &bfin_uart1_device,
 768#endif
 769#endif
 770
 771#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
 772#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 773        &bfin_sport0_uart_device,
 774#endif
 775#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 776        &bfin_sport1_uart_device,
 777#endif
 778#endif
 779};
 780
 781void __init native_machine_early_platform_add_devices(void)
 782{
 783        printk(KERN_INFO "register early platform devices\n");
 784        early_platform_add_devices(cm_bf537_early_devices,
 785                ARRAY_SIZE(cm_bf537_early_devices));
 786}
 787
 788int bfin_get_ether_addr(char *addr)
 789{
 790        return 1;
 791}
 792EXPORT_SYMBOL(bfin_get_ether_addr);
 793