linux/drivers/atm/midway.h
<<
>>
Prefs
   1/* SPDX-License-Identifier: GPL-2.0 */
   2/* drivers/atm/midway.h - Efficient Networks Midway (SAR) description */
   3 
   4/* Written 1995-1999 by Werner Almesberger, EPFL LRC/ICA */
   5 
   6
   7#ifndef DRIVERS_ATM_MIDWAY_H
   8#define DRIVERS_ATM_MIDWAY_H
   9
  10
  11#define NR_VCI          1024            /* number of VCIs */
  12#define NR_VCI_LD       10              /* log2(NR_VCI) */
  13#define NR_DMA_RX       512             /* RX DMA queue entries */
  14#define NR_DMA_TX       512             /* TX DMA queue entries */
  15#define NR_SERVICE      NR_VCI          /* service list size */
  16#define NR_CHAN         8               /* number of TX channels */
  17#define TS_CLOCK        25000000        /* traffic shaper clock (cell/sec) */
  18
  19#define MAP_MAX_SIZE    0x00400000      /* memory window for max config */
  20#define EPROM_SIZE      0x00010000
  21#define MEM_VALID       0xffc00000      /* mask base address with this */
  22#define PHY_BASE        0x00020000      /* offset of PHY register are */
  23#define REG_BASE        0x00040000      /* offset of Midway register area */
  24#define RAM_BASE        0x00200000      /* offset of RAM area */
  25#define RAM_INCREMENT   0x00020000      /* probe for RAM every 128kB */
  26
  27#define MID_VCI_BASE    RAM_BASE
  28#define MID_DMA_RX_BASE (MID_VCI_BASE+NR_VCI*16)
  29#define MID_DMA_TX_BASE (MID_DMA_RX_BASE+NR_DMA_RX*8)
  30#define MID_SERVICE_BASE (MID_DMA_TX_BASE+NR_DMA_TX*8)
  31#define MID_FREE_BASE   (MID_SERVICE_BASE+NR_SERVICE*4)
  32
  33#define MAC_LEN 6 /* atm.h */
  34
  35#define MID_MIN_BUF_SIZE (1024)         /*   1 kB is minimum */
  36#define MID_MAX_BUF_SIZE (128*1024)     /* 128 kB is maximum */
  37
  38#define RX_DESCR_SIZE   1               /* RX PDU descr is 1 longword */
  39#define TX_DESCR_SIZE   2               /* TX PDU descr is 2 longwords */
  40#define AAL5_TRAILER    (ATM_AAL5_TRAILER/4) /* AAL5 trailer is 2 longwords */
  41
  42#define TX_GAP          8               /* TX buffer gap (words) */
  43
  44/*
  45 * Midway Reset/ID
  46 *
  47 * All values read-only. Writing to this register resets Midway chip.
  48 */
  49
  50#define MID_RES_ID_MCON 0x00            /* Midway Reset/ID */
  51
  52#define MID_ID          0xf0000000      /* Midway version */
  53#define MID_SHIFT       24
  54#define MID_MOTHER_ID   0x00000700      /* mother board id */
  55#define MID_MOTHER_SHIFT 8
  56#define MID_CON_TI      0x00000080      /* 0: normal ctrl; 1: SABRE */
  57#define MID_CON_SUNI    0x00000040      /* 0: UTOPIA; 1: SUNI */
  58#define MID_CON_V6      0x00000020      /* 0: non-pipel UTOPIA (required iff
  59                                           !CON_SUNI; 1: UTOPIA */
  60#define DAUGHTER_ID     0x0000001f      /* daughter board id */
  61
  62/*
  63 * Interrupt Status Acknowledge, Interrupt Status & Interrupt Enable
  64 */
  65
  66#define MID_ISA         0x01            /* Interrupt Status Acknowledge */
  67#define MID_IS          0x02            /* Interrupt Status */
  68#define MID_IE          0x03            /* Interrupt Enable */
  69
  70#define MID_TX_COMPLETE_7 0x00010000    /* channel N completed a PDU */
  71#define MID_TX_COMPLETE_6 0x00008000    /* transmission */
  72#define MID_TX_COMPLETE_5 0x00004000
  73#define MID_TX_COMPLETE_4 0x00002000
  74#define MID_TX_COMPLETE_3 0x00001000
  75#define MID_TX_COMPLETE_2 0x00000800
  76#define MID_TX_COMPLETE_1 0x00000400
  77#define MID_TX_COMPLETE_0 0x00000200
  78#define MID_TX_COMPLETE 0x0001fe00      /* any TX */
  79#define MID_TX_DMA_OVFL 0x00000100      /* DMA to adapter overflow */
  80#define MID_TX_IDENT_MISM 0x00000080    /* TX: ident mismatch => halted */
  81#define MID_DMA_LERR_ACK 0x00000040     /* LERR - SBus ? */
  82#define MID_DMA_ERR_ACK 0x00000020      /* DMA error */
  83#define MID_RX_DMA_COMPLETE 0x00000010  /* DMA to host done */
  84#define MID_TX_DMA_COMPLETE 0x00000008  /* DMA from host done */
  85#define MID_SERVICE     0x00000004      /* something in service list */
  86#define MID_SUNI_INT    0x00000002      /* interrupt from SUNI */
  87#define MID_STAT_OVFL   0x00000001      /* statistics overflow */
  88
  89/*
  90 * Master Control/Status
  91 */
  92
  93#define MID_MC_S        0x04
  94
  95#define MID_INT_SELECT  0x000001C0      /* Interrupt level (000: off) */
  96#define MID_INT_SEL_SHIFT 6
  97#define MID_TX_LOCK_MODE 0x00000020     /* 0: streaming; 1: TX ovfl->lock */
  98#define MID_DMA_ENABLE  0x00000010      /* R: 0: disable; 1: enable
  99                                           W: 0: no change; 1: enable */
 100#define MID_TX_ENABLE   0x00000008      /* R: 0: TX disabled; 1: enabled
 101                                           W: 0: no change; 1: enable */
 102#define MID_RX_ENABLE   0x00000004      /* like TX */
 103#define MID_WAIT_1MS    0x00000002      /* R: 0: timer not running; 1: running
 104                                           W: 0: no change; 1: no interrupts
 105                                                               for 1 ms */
 106#define MID_WAIT_500US  0x00000001      /* like WAIT_1MS, but 0.5 ms */
 107
 108/*
 109 * Statistics
 110 *
 111 * Cleared when reading.
 112 */
 113
 114#define MID_STAT                0x05
 115
 116#define MID_VCI_TRASH   0xFFFF0000      /* trashed cells because of VCI mode */
 117#define MID_VCI_TRASH_SHIFT 16
 118#define MID_OVFL_TRASH  0x0000FFFF      /* trashed cells because of overflow */
 119
 120/*
 121 * Address registers
 122 */
 123
 124#define MID_SERV_WRITE  0x06    /* free pos in service area (R, 10 bits) */
 125#define MID_DMA_ADDR    0x07    /* virtual DMA address (R, 32 bits) */
 126#define MID_DMA_WR_RX   0x08    /* (RW, 9 bits) */
 127#define MID_DMA_RD_RX   0x09
 128#define MID_DMA_WR_TX   0x0A
 129#define MID_DMA_RD_TX   0x0B
 130
 131/*
 132 * Transmit Place Registers (0x10+4*channel)
 133 */
 134
 135#define MID_TX_PLACE(c) (0x10+4*(c))
 136
 137#define MID_SIZE        0x00003800      /* size, N*256 x 32 bit */
 138#define MID_SIZE_SHIFT  11
 139#define MID_LOCATION    0x000007FF      /* location in adapter memory (word) */
 140
 141#define MID_LOC_SKIP    8               /* 8 bits of location are always zero
 142                                           (applies to all uses of location) */
 143
 144/*
 145 * Transmit ReadPtr Registers (0x11+4*channel)
 146 */
 147
 148#define MID_TX_RDPTR(c) (0x11+4*(c))
 149
 150#define MID_READ_PTR    0x00007FFF      /* next word for PHY */
 151
 152/*
 153 * Transmit DescrStart Registers (0x12+4*channel)
 154 */
 155
 156#define MID_TX_DESCRSTART(c) (0x12+4*(c))
 157
 158#define MID_DESCR_START 0x00007FFF      /* seg buffer being DMAed */
 159
 160#define ENI155_MAGIC    0xa54b872d
 161
 162struct midway_eprom {
 163        unsigned char mac[MAC_LEN],inv_mac[MAC_LEN];
 164        unsigned char pad[36];
 165        u32 serial,inv_serial;
 166        u32 magic,inv_magic;
 167};
 168
 169
 170/*
 171 * VCI table entry
 172 */
 173
 174#define MID_VCI_IN_SERVICE      0x00000001      /* set if VCI is currently in
 175                                                   service list */
 176#define MID_VCI_SIZE            0x00038000      /* reassembly buffer size,
 177                                                   2*<size> kB */
 178#define MID_VCI_SIZE_SHIFT      15
 179#define MID_VCI_LOCATION        0x1ffc0000      /* buffer location */
 180#define MID_VCI_LOCATION_SHIFT  18
 181#define MID_VCI_PTI_MODE        0x20000000      /* 0: trash, 1: preserve */
 182#define MID_VCI_MODE            0xc0000000
 183#define MID_VCI_MODE_SHIFT      30
 184#define MID_VCI_READ            0x00007fff
 185#define MID_VCI_READ_SHIFT      0
 186#define MID_VCI_DESCR           0x7fff0000
 187#define MID_VCI_DESCR_SHIFT     16
 188#define MID_VCI_COUNT           0x000007ff
 189#define MID_VCI_COUNT_SHIFT     0
 190#define MID_VCI_STATE           0x0000c000
 191#define MID_VCI_STATE_SHIFT     14
 192#define MID_VCI_WRITE           0x7fff0000
 193#define MID_VCI_WRITE_SHIFT     16
 194
 195#define MID_MODE_TRASH  0
 196#define MID_MODE_RAW    1
 197#define MID_MODE_AAL5   2
 198
 199/*
 200 * Reassembly buffer descriptor
 201 */
 202
 203#define MID_RED_COUNT           0x000007ff
 204#define MID_RED_CRC_ERR         0x00000800
 205#define MID_RED_T               0x00001000
 206#define MID_RED_CE              0x00010000
 207#define MID_RED_CLP             0x01000000
 208#define MID_RED_IDEN            0xfe000000
 209#define MID_RED_SHIFT           25
 210
 211#define MID_RED_RX_ID           0x1b            /* constant identifier */
 212
 213/*
 214 * Segmentation buffer descriptor
 215 */
 216
 217#define MID_SEG_COUNT           MID_RED_COUNT
 218#define MID_SEG_RATE            0x01f80000
 219#define MID_SEG_RATE_SHIFT      19
 220#define MID_SEG_PR              0x06000000
 221#define MID_SEG_PR_SHIFT        25
 222#define MID_SEG_AAL5            0x08000000
 223#define MID_SEG_ID              0xf0000000
 224#define MID_SEG_ID_SHIFT        28
 225#define MID_SEG_MAX_RATE        63
 226
 227#define MID_SEG_CLP             0x00000001
 228#define MID_SEG_PTI             0x0000000e
 229#define MID_SEG_PTI_SHIFT       1
 230#define MID_SEG_VCI             0x00003ff0
 231#define MID_SEG_VCI_SHIFT       4
 232
 233#define MID_SEG_TX_ID           0xb             /* constant identifier */
 234
 235/*
 236 * DMA entry
 237 */
 238
 239#define MID_DMA_COUNT           0xffff0000
 240#define MID_DMA_COUNT_SHIFT     16
 241#define MID_DMA_END             0x00000020
 242#define MID_DMA_TYPE            0x0000000f
 243
 244#define MID_DT_JK       0x3
 245#define MID_DT_WORD     0x0
 246#define MID_DT_2W       0x7
 247#define MID_DT_4W       0x4
 248#define MID_DT_8W       0x5
 249#define MID_DT_16W      0x6
 250#define MID_DT_2WM      0xf
 251#define MID_DT_4WM      0xc
 252#define MID_DT_8WM      0xd
 253#define MID_DT_16WM     0xe
 254
 255/* only for RX*/
 256#define MID_DMA_VCI             0x0000ffc0
 257#define MID_DMA_VCI_SHIFT       6
 258
 259/* only for TX */
 260#define MID_DMA_CHAN            0x000001c0
 261#define MID_DMA_CHAN_SHIFT      6
 262
 263#define MID_DT_BYTE     0x1
 264#define MID_DT_HWORD    0x2
 265
 266#endif
 267