1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18#include <linux/types.h>
19#include <linux/init.h>
20#include <linux/kernel.h>
21#include <linux/memory.h>
22#include <linux/platform_device.h>
23#include <linux/gpio.h>
24#include <linux/moduleparam.h>
25#include <linux/smsc911x.h>
26#include <linux/mfd/mc13783.h>
27#include <linux/spi/spi.h>
28#include <linux/usb/otg.h>
29#include <linux/usb/ulpi.h>
30#include <linux/mtd/physmap.h>
31#include <linux/delay.h>
32#include <linux/regulator/machine.h>
33#include <linux/regulator/fixed.h>
34
35#include <asm/mach-types.h>
36#include <asm/mach/arch.h>
37#include <asm/mach/time.h>
38#include <asm/mach/map.h>
39#include <asm/page.h>
40#include <asm/setup.h>
41
42#include "board-mx31lite.h"
43#include "common.h"
44#include "devices-imx31.h"
45#include "ehci.h"
46#include "hardware.h"
47#include "iomux-mx3.h"
48#include "ulpi.h"
49
50
51
52
53
54static unsigned int mx31lite_pins[] = {
55
56 MX31_PIN_CTS1__CTS1,
57 MX31_PIN_RTS1__RTS1,
58 MX31_PIN_TXD1__TXD1,
59 MX31_PIN_RXD1__RXD1,
60
61 MX31_PIN_CSPI1_SCLK__SCLK,
62 MX31_PIN_CSPI1_MOSI__MOSI,
63 MX31_PIN_CSPI1_MISO__MISO,
64 MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
65 MX31_PIN_CSPI1_SS0__SS0,
66 MX31_PIN_CSPI1_SS1__SS1,
67 MX31_PIN_CSPI1_SS2__SS2,
68
69 IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO),
70
71 MX31_PIN_CSPI2_SCLK__SCLK,
72 MX31_PIN_CSPI2_MOSI__MOSI,
73 MX31_PIN_CSPI2_MISO__MISO,
74 MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
75 MX31_PIN_CSPI2_SS0__SS0,
76 MX31_PIN_CSPI2_SS1__SS1,
77 MX31_PIN_CSPI2_SS2__SS2,
78};
79
80
81static const struct imxuart_platform_data uart_pdata __initconst = {
82 .flags = IMXUART_HAVE_RTSCTS,
83};
84
85
86static int spi0_internal_chipselect[] = {
87 MXC_SPI_CS(0),
88 MXC_SPI_CS(1),
89 MXC_SPI_CS(2),
90};
91
92static const struct spi_imx_master spi0_pdata __initconst = {
93 .chipselect = spi0_internal_chipselect,
94 .num_chipselect = ARRAY_SIZE(spi0_internal_chipselect),
95};
96
97static const struct mxc_nand_platform_data
98mx31lite_nand_board_info __initconst = {
99 .width = 1,
100 .hw_ecc = 1,
101};
102
103static struct smsc911x_platform_config smsc911x_config = {
104 .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
105 .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
106 .flags = SMSC911X_USE_16BIT,
107};
108
109static struct resource smsc911x_resources[] = {
110 {
111 .start = MX31_CS4_BASE_ADDR,
112 .end = MX31_CS4_BASE_ADDR + 0x100,
113 .flags = IORESOURCE_MEM,
114 }, {
115
116 .flags = IORESOURCE_IRQ,
117 },
118};
119
120static struct platform_device smsc911x_device = {
121 .name = "smsc911x",
122 .id = -1,
123 .num_resources = ARRAY_SIZE(smsc911x_resources),
124 .resource = smsc911x_resources,
125 .dev = {
126 .platform_data = &smsc911x_config,
127 },
128};
129
130
131
132
133
134
135
136static int spi1_internal_chipselect[] = {
137 MXC_SPI_CS(0),
138};
139
140static const struct spi_imx_master spi1_pdata __initconst = {
141 .chipselect = spi1_internal_chipselect,
142 .num_chipselect = ARRAY_SIZE(spi1_internal_chipselect),
143};
144
145static struct mc13xxx_platform_data mc13783_pdata __initdata = {
146 .flags = MC13XXX_USE_RTC,
147};
148
149static struct spi_board_info mc13783_spi_dev __initdata = {
150 .modalias = "mc13783",
151 .max_speed_hz = 1000000,
152 .bus_num = 1,
153 .chip_select = 0,
154 .platform_data = &mc13783_pdata,
155
156};
157
158
159
160
161
162#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
163 PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
164
165static int usbh2_init(struct platform_device *pdev)
166{
167 int pins[] = {
168 MX31_PIN_USBH2_DATA0__USBH2_DATA0,
169 MX31_PIN_USBH2_DATA1__USBH2_DATA1,
170 MX31_PIN_USBH2_CLK__USBH2_CLK,
171 MX31_PIN_USBH2_DIR__USBH2_DIR,
172 MX31_PIN_USBH2_NXT__USBH2_NXT,
173 MX31_PIN_USBH2_STP__USBH2_STP,
174 };
175
176 mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2");
177
178 mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
179 mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
180 mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
181 mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
182 mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
183 mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
184 mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
185 mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
186 mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
187 mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
188 mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
189 mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
190
191 mxc_iomux_set_gpr(MUX_PGP_UH2, true);
192
193
194 mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO),
195 "USBH2_CS");
196 gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS");
197 gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0);
198
199 mdelay(10);
200
201 return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
202}
203
204static struct mxc_usbh_platform_data usbh2_pdata __initdata = {
205 .init = usbh2_init,
206 .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
207};
208
209
210
211
212
213static struct physmap_flash_data nor_flash_data = {
214 .width = 2,
215};
216
217static struct resource nor_flash_resource = {
218 .start = 0xa0000000,
219 .end = 0xa1ffffff,
220 .flags = IORESOURCE_MEM,
221};
222
223static struct platform_device physmap_flash_device = {
224 .name = "physmap-flash",
225 .id = 0,
226 .dev = {
227 .platform_data = &nor_flash_data,
228 },
229 .resource = &nor_flash_resource,
230 .num_resources = 1,
231};
232
233
234
235
236static struct map_desc mx31lite_io_desc[] __initdata = {
237 {
238 .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
239 .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
240 .length = MX31_CS4_SIZE,
241 .type = MT_DEVICE
242 }
243};
244
245
246
247
248static void __init mx31lite_map_io(void)
249{
250 mx31_map_io();
251 iotable_init(mx31lite_io_desc, ARRAY_SIZE(mx31lite_io_desc));
252}
253
254static int mx31lite_baseboard;
255core_param(mx31lite_baseboard, mx31lite_baseboard, int, 0444);
256
257static struct regulator_consumer_supply dummy_supplies[] = {
258 REGULATOR_SUPPLY("vdd33a", "smsc911x"),
259 REGULATOR_SUPPLY("vddvario", "smsc911x"),
260};
261
262static void __init mx31lite_init(void)
263{
264 imx31_soc_init();
265
266 mxc_iomux_setup_multiple_pins(mx31lite_pins, ARRAY_SIZE(mx31lite_pins),
267 "mx31lite");
268
269 imx31_add_imx_uart0(&uart_pdata);
270 imx31_add_spi_imx0(&spi0_pdata);
271
272
273 platform_device_register(&physmap_flash_device);
274 imx31_add_mxc_nand(&mx31lite_nand_board_info);
275
276 imx31_add_spi_imx1(&spi1_pdata);
277
278 regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
279}
280
281static void __init mx31lite_late(void)
282{
283 int ret;
284
285 if (mx31lite_baseboard == MX31LITE_DB)
286 mx31lite_db_init();
287
288 mc13783_spi_dev.irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
289 spi_register_board_info(&mc13783_spi_dev, 1);
290
291
292 usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
293 ULPI_OTG_DRVVBUS_EXT);
294 if (usbh2_pdata.otg)
295 imx31_add_mxc_ehci_hs(2, &usbh2_pdata);
296
297
298 ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_SFS6), "sms9117-irq");
299 if (ret)
300 pr_warn("could not get LAN irq gpio\n");
301 else {
302 gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_SFS6));
303 smsc911x_resources[1].start =
304 gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
305 smsc911x_resources[1].end =
306 gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SFS6));
307 platform_device_register(&smsc911x_device);
308 }
309}
310
311static void __init mx31lite_timer_init(void)
312{
313 mx31_clocks_init(26000000);
314}
315
316MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
317
318 .atag_offset = 0x100,
319 .map_io = mx31lite_map_io,
320 .init_early = imx31_init_early,
321 .init_irq = mx31_init_irq,
322 .init_time = mx31lite_timer_init,
323 .init_machine = mx31lite_init,
324 .init_late = mx31lite_late,
325 .restart = mxc_restart,
326MACHINE_END
327