linux/Documentation/btmrvl.txt
<<
>>
Prefs
   1=============
   2btmrvl driver
   3=============
   4
   5All commands are used via debugfs interface.
   6
   7Set/get driver configurations
   8=============================
   9
  10Path:   /debug/btmrvl/config/
  11
  12gpiogap=[n], hscfgcmd
  13        These commands are used to configure the host sleep parameters::
  14        bit 8:0  -- Gap
  15        bit 16:8 -- GPIO
  16
  17        where GPIO is the pin number of GPIO used to wake up the host.
  18        It could be any valid GPIO pin# (e.g. 0-7) or 0xff (SDIO interface
  19        wakeup will be used instead).
  20
  21        where Gap is the gap in milli seconds between wakeup signal and
  22        wakeup event, or 0xff for special host sleep setting.
  23
  24        Usage::
  25
  26                # Use SDIO interface to wake up the host and set GAP to 0x80:
  27                echo 0xff80 > /debug/btmrvl/config/gpiogap
  28                echo 1 > /debug/btmrvl/config/hscfgcmd
  29
  30                # Use GPIO pin #3 to wake up the host and set GAP to 0xff:
  31                echo 0x03ff >  /debug/btmrvl/config/gpiogap
  32                echo 1 > /debug/btmrvl/config/hscfgcmd
  33
  34psmode=[n], pscmd
  35        These commands are used to enable/disable auto sleep mode
  36
  37        where the option is::
  38
  39                        1       -- Enable auto sleep mode
  40                        0       -- Disable auto sleep mode
  41
  42        Usage::
  43
  44                # Enable auto sleep mode
  45                echo 1 > /debug/btmrvl/config/psmode
  46                echo 1 > /debug/btmrvl/config/pscmd
  47
  48                # Disable auto sleep mode
  49                echo 0 > /debug/btmrvl/config/psmode
  50                echo 1 > /debug/btmrvl/config/pscmd
  51
  52
  53hsmode=[n], hscmd
  54        These commands are used to enable host sleep or wake up firmware
  55
  56        where the option is::
  57
  58                        1       -- Enable host sleep
  59                        0       -- Wake up firmware
  60
  61        Usage::
  62
  63                # Enable host sleep
  64                echo 1 > /debug/btmrvl/config/hsmode
  65                echo 1 > /debug/btmrvl/config/hscmd
  66
  67                # Wake up firmware
  68                echo 0 > /debug/btmrvl/config/hsmode
  69                echo 1 > /debug/btmrvl/config/hscmd
  70
  71
  72Get driver status
  73=================
  74
  75Path:   /debug/btmrvl/status/
  76
  77Usage::
  78
  79        cat /debug/btmrvl/status/<args>
  80
  81where the args are:
  82
  83curpsmode
  84        This command displays current auto sleep status.
  85
  86psstate
  87        This command display the power save state.
  88
  89hsstate
  90        This command display the host sleep state.
  91
  92txdnldrdy
  93        This command displays the value of Tx download ready flag.
  94
  95Issuing a raw hci command
  96=========================
  97
  98Use hcitool to issue raw hci command, refer to hcitool manual
  99
 100Usage::
 101
 102        Hcitool cmd <ogf> <ocf> [Parameters]
 103
 104Interface Control Command::
 105
 106        hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00    --Enable All interface
 107        hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01    --Enable Wlan interface
 108        hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02    --Enable BT interface
 109        hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00    --Disable All interface
 110        hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01    --Disable Wlan interface
 111        hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02    --Disable BT interface
 112
 113SD8688 firmware
 114===============
 115
 116Images:
 117
 118- /lib/firmware/sd8688_helper.bin
 119- /lib/firmware/sd8688.bin
 120
 121
 122The images can be downloaded from:
 123
 124git.infradead.org/users/dwmw2/linux-firmware.git/libertas/
 125