LXR linux/arch/arm/mach-u300/core.c

   1/*
   2 *
   3 * arch/arm/mach-u300/core.c
   4 *
   5 *
   6 * Copyright (C) 2007-2012 ST-Ericsson SA
   7 * License terms: GNU General Public License (GPL) version 2
   8 * Core platform support, IRQ handling and device definitions.
   9 * Author: Linus Walleij <linus.walleij@stericsson.com>
  10 */
  11#include <linux/kernel.h>
  12#include <linux/pinctrl/machine.h>
  13#include <linux/pinctrl/pinconf-generic.h>
  14#include <linux/platform_data/clk-u300.h>
  15#include <linux/irqchip.h>
  16#include <linux/of_address.h>
  17#include <linux/of_platform.h>
  18#include <linux/clocksource.h>
  19#include <linux/clk.h>
  20
  21#include <asm/mach/map.h>
  22#include <asm/mach/arch.h>
  23
  24/*
  25 * These are the large blocks of memory allocated for I/O.
  26 * the defines are used for setting up the I/O memory mapping.
  27 */
  28
  29/* NAND Flash CS0 */
  30#define U300_NAND_CS0_PHYS_BASE         0x80000000
  31/* NFIF */
  32#define U300_NAND_IF_PHYS_BASE          0x9f800000
  33/* ALE, CLE offset for FSMC NAND */
  34#define PLAT_NAND_CLE                   (1 << 16)
  35#define PLAT_NAND_ALE                   (1 << 17)
  36/* AHB Peripherals */
  37#define U300_AHB_PER_PHYS_BASE          0xa0000000
  38#define U300_AHB_PER_VIRT_BASE          0xff010000
  39/* FAST Peripherals */
  40#define U300_FAST_PER_PHYS_BASE         0xc0000000
  41#define U300_FAST_PER_VIRT_BASE         0xff020000
  42/* SLOW Peripherals */
  43#define U300_SLOW_PER_PHYS_BASE         0xc0010000
  44#define U300_SLOW_PER_VIRT_BASE         0xff000000
  45/* Boot ROM */
  46#define U300_BOOTROM_PHYS_BASE          0xffff0000
  47#define U300_BOOTROM_VIRT_BASE          0xffff0000
  48/* SEMI config base */
  49#define U300_SEMI_CONFIG_BASE           0x2FFE0000
  50
  51/*
  52 * AHB peripherals
  53 */
  54
  55/* AHB Peripherals Bridge Controller */
  56#define U300_AHB_BRIDGE_BASE            (U300_AHB_PER_PHYS_BASE+0x0000)
  57/* Vectored Interrupt Controller 0, servicing 32 interrupts */
  58#define U300_INTCON0_BASE               (U300_AHB_PER_PHYS_BASE+0x1000)
  59#define U300_INTCON0_VBASE              IOMEM(U300_AHB_PER_VIRT_BASE+0x1000)
  60/* Vectored Interrupt Controller 1, servicing 32 interrupts */
  61#define U300_INTCON1_BASE               (U300_AHB_PER_PHYS_BASE+0x2000)
  62#define U300_INTCON1_VBASE              IOMEM(U300_AHB_PER_VIRT_BASE+0x2000)
  63/* Memory Stick Pro (MSPRO) controller */
  64#define U300_MSPRO_BASE                 (U300_AHB_PER_PHYS_BASE+0x3000)
  65/* EMIF Configuration Area */
  66#define U300_EMIF_CFG_BASE              (U300_AHB_PER_PHYS_BASE+0x4000)
  67
  68/*
  69 * FAST peripherals
  70 */
  71
  72/* FAST bridge control */
  73#define U300_FAST_BRIDGE_BASE           (U300_FAST_PER_PHYS_BASE+0x0000)
  74/* MMC/SD controller */
  75#define U300_MMCSD_BASE                 (U300_FAST_PER_PHYS_BASE+0x1000)
  76/* PCM I2S0 controller */
  77#define U300_PCM_I2S0_BASE              (U300_FAST_PER_PHYS_BASE+0x2000)
  78/* PCM I2S1 controller */
  79#define U300_PCM_I2S1_BASE              (U300_FAST_PER_PHYS_BASE+0x3000)
  80/* I2C0 controller */
  81#define U300_I2C0_BASE                  (U300_FAST_PER_PHYS_BASE+0x4000)
  82/* I2C1 controller */
  83#define U300_I2C1_BASE                  (U300_FAST_PER_PHYS_BASE+0x5000)
  84/* SPI controller */
  85#define U300_SPI_BASE                   (U300_FAST_PER_PHYS_BASE+0x6000)
  86/* Fast UART1 on U335 only */
  87#define U300_UART1_BASE                 (U300_FAST_PER_PHYS_BASE+0x7000)
  88
  89/*
  90 * SLOW peripherals
  91 */
  92
  93/* SLOW bridge control */
  94#define U300_SLOW_BRIDGE_BASE           (U300_SLOW_PER_PHYS_BASE)
  95/* SYSCON */
  96#define U300_SYSCON_BASE                (U300_SLOW_PER_PHYS_BASE+0x1000)
  97#define U300_SYSCON_VBASE               IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000)
  98/* Watchdog */
  99#define U300_WDOG_BASE                  (U300_SLOW_PER_PHYS_BASE+0x2000)
 100/* UART0 */
 101#define U300_UART0_BASE                 (U300_SLOW_PER_PHYS_BASE+0x3000)
 102/* APP side special timer */
 103#define U300_TIMER_APP_BASE             (U300_SLOW_PER_PHYS_BASE+0x4000)
 104#define U300_TIMER_APP_VBASE            IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000)
 105/* Keypad */
 106#define U300_KEYPAD_BASE                (U300_SLOW_PER_PHYS_BASE+0x5000)
 107/* GPIO */
 108#define U300_GPIO_BASE                  (U300_SLOW_PER_PHYS_BASE+0x6000)
 109/* RTC */
 110#define U300_RTC_BASE                   (U300_SLOW_PER_PHYS_BASE+0x7000)
 111/* Bus tracer */
 112#define U300_BUSTR_BASE                 (U300_SLOW_PER_PHYS_BASE+0x8000)
 113/* Event handler (hardware queue) */
 114#define U300_EVHIST_BASE                (U300_SLOW_PER_PHYS_BASE+0x9000)
 115/* Genric Timer */
 116#define U300_TIMER_BASE                 (U300_SLOW_PER_PHYS_BASE+0xa000)
 117/* PPM */
 118#define U300_PPM_BASE                   (U300_SLOW_PER_PHYS_BASE+0xb000)
 119
 120/*
 121 * REST peripherals
 122 */
 123
 124/* ISP (image signal processor) */
 125#define U300_ISP_BASE                   (0xA0008000)
 126/* DMA Controller base */
 127#define U300_DMAC_BASE                  (0xC0020000)
 128/* MSL Base */
 129#define U300_MSL_BASE                   (0xc0022000)
 130/* APEX Base */
 131#define U300_APEX_BASE                  (0xc0030000)
 132/* Video Encoder Base */
 133#define U300_VIDEOENC_BASE              (0xc0080000)
 134/* XGAM Base */
 135#define U300_XGAM_BASE                  (0xd0000000)
 136
 137/*
 138 * SYSCON addresses applicable to the core machine.
 139 */
 140
 141/* Chip ID register 16bit (R/-) */
 142#define U300_SYSCON_CIDR                                        (0x400)
 143/* SMCR */
 144#define U300_SYSCON_SMCR                                        (0x4d0)
 145#define U300_SYSCON_SMCR_FIELD_MASK                             (0x000e)
 146#define U300_SYSCON_SMCR_SEMI_SREFACK_IND                       (0x0008)
 147#define U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE                    (0x0004)
 148#define U300_SYSCON_SMCR_SEMI_EXT_BOOT_MODE_ENABLE              (0x0002)
 149/* CPU_SW_DBGEN Software Debug Enable 16bit (R/W) */
 150#define U300_SYSCON_CSDR                                        (0x4f0)
 151#define U300_SYSCON_CSDR_SW_DEBUG_ENABLE                        (0x0001)
 152/* PRINT_CONTROL Print Control 16bit (R/-) */
 153#define U300_SYSCON_PCR                                         (0x4f8)
 154#define U300_SYSCON_PCR_SERV_IND                                (0x0001)
 155/* BOOT_CONTROL 16bit (R/-) */
 156#define U300_SYSCON_BCR                                         (0x4fc)
 157#define U300_SYSCON_BCR_ACC_CPU_SUBSYS_VINITHI_IND              (0x0400)
 158#define U300_SYSCON_BCR_APP_CPU_SUBSYS_VINITHI_IND              (0x0200)
 159#define U300_SYSCON_BCR_EXTRA_BOOT_OPTION_MASK                  (0x01FC)
 160#define U300_SYSCON_BCR_APP_BOOT_SERV_MASK                      (0x0003)
 161
 162static void __iomem *syscon_base;
 163
 164/*
 165 * Static I/O mappings that are needed for booting the U300 platforms. The
 166 * only things we need are the areas where we find the timer, syscon and
 167 * intcon, since the remaining device drivers will map their own memory
 168 * physical to virtual as the need arise.
 169 */
 170static struct map_desc u300_io_desc[] __initdata = {
 171        {
 172                .virtual        = U300_SLOW_PER_VIRT_BASE,
 173                .pfn            = __phys_to_pfn(U300_SLOW_PER_PHYS_BASE),
 174                .length         = SZ_64K,
 175                .type           = MT_DEVICE,
 176        },
 177        {
 178                .virtual        = U300_AHB_PER_VIRT_BASE,
 179                .pfn            = __phys_to_pfn(U300_AHB_PER_PHYS_BASE),
 180                .length         = SZ_32K,
 181                .type           = MT_DEVICE,
 182        },
 183        {
 184                .virtual        = U300_FAST_PER_VIRT_BASE,
 185                .pfn            = __phys_to_pfn(U300_FAST_PER_PHYS_BASE),
 186                .length         = SZ_32K,
 187                .type           = MT_DEVICE,
 188        },
 189};
 190
 191static void __init u300_map_io(void)
 192{
 193        iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
 194}
 195
 196static unsigned long pin_pullup_conf[] = {
 197        PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 1),
 198};
 199
 200static unsigned long pin_highz_conf[] = {
 201        PIN_CONF_PACKED(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0),
 202};
 203
 204/* Pin control settings */
 205static struct pinctrl_map __initdata u300_pinmux_map[] = {
 206        /* anonymous maps for chip power and EMIFs */
 207        PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
 208        PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),
 209        PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif1"),
 210        /* per-device maps for MMC/SD, SPI and UART */
 211        PIN_MAP_MUX_GROUP_DEFAULT("mmci",  "pinctrl-u300", NULL, "mmc0"),
 212        PIN_MAP_MUX_GROUP_DEFAULT("pl022", "pinctrl-u300", NULL, "spi0"),
 213        PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-u300", NULL, "uart0"),
 214        /* This pin is used for clock return rather than GPIO */
 215        PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO APP GPIO 11",
 216                                    pin_pullup_conf),
 217        /* This pin is used for card detect */
 218        PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO MS INS",
 219                                    pin_highz_conf),
 220};
 221
 222struct db_chip {
 223        u16 chipid;
 224        const char *name;
 225};
 226
 227/*
 228 * This is a list of the Digital Baseband chips used in the U300 platform.
 229 */
 230static struct db_chip db_chips[] __initdata = {
 231        {
 232                .chipid = 0xb800,
 233                .name = "DB3000",
 234        },
 235        {
 236                .chipid = 0xc000,
 237                .name = "DB3100",
 238        },
 239        {
 240                .chipid = 0xc800,
 241                .name = "DB3150",
 242        },
 243        {
 244                .chipid = 0xd800,
 245                .name = "DB3200",
 246        },
 247        {
 248                .chipid = 0xe000,
 249                .name = "DB3250",
 250        },
 251        {
 252                .chipid = 0xe800,
 253                .name = "DB3210",
 254        },
 255        {
 256                .chipid = 0xf000,
 257                .name = "DB3350 P1x",
 258        },
 259        {
 260                .chipid = 0xf100,
 261                .name = "DB3350 P2x",
 262        },
 263        {
 264                .chipid = 0x0000, /* List terminator */
 265                .name = NULL,
 266        }
 267};
 268
 269static void __init u300_init_check_chip(void)
 270{
 271
 272        u16 val;
 273        struct db_chip *chip;
 274        const char *chipname;
 275        const char unknown[] = "UNKNOWN";
 276
 277        /* Read out and print chip ID */
 278        val = readw(syscon_base + U300_SYSCON_CIDR);
 279        /* This is in funky bigendian order... */
 280        val = (val & 0xFFU) << 8 | (val >> 8);
 281        chip = db_chips;
 282        chipname = unknown;
 283
 284        for ( ; chip->chipid; chip++) {
 285                if (chip->chipid == (val & 0xFF00U)) {
 286                        chipname = chip->name;
 287                        break;
 288                }
 289        }
 290        printk(KERN_INFO "Initializing U300 system on %s baseband chip " \
 291               "(chip ID 0x%04x)\n", chipname, val);
 292
 293        if ((val & 0xFF00U) != 0xf000 && (val & 0xFF00U) != 0xf100) {
 294                printk(KERN_ERR "Platform configured for BS335 " \
 295                       " with DB3350 but %s detected, expect problems!",
 296                       chipname);
 297        }
 298}
 299
 300/* Forward declare this function from the watchdog */
 301void coh901327_watchdog_reset(void);
 302
 303static void u300_restart(enum reboot_mode mode, const char *cmd)
 304{
 305        switch (mode) {
 306        case REBOOT_SOFT:
 307        case REBOOT_HARD:
 308#ifdef CONFIG_COH901327_WATCHDOG
 309                coh901327_watchdog_reset();
 310#endif
 311                break;
 312        default:
 313                /* Do nothing */
 314                break;
 315        }
 316        /* Wait for system do die/reset. */
 317        while (1);
 318}
 319
 320/* These are mostly to get the right device names for the clock lookups */
 321static struct of_dev_auxdata u300_auxdata_lookup[] __initdata = {
 322        OF_DEV_AUXDATA("stericsson,pinctrl-u300", U300_SYSCON_BASE,
 323                "pinctrl-u300", NULL),
 324        OF_DEV_AUXDATA("stericsson,gpio-coh901", U300_GPIO_BASE,
 325                "u300-gpio", NULL),
 326        OF_DEV_AUXDATA("stericsson,coh901327", U300_WDOG_BASE,
 327                "coh901327_wdog", NULL),
 328        OF_DEV_AUXDATA("stericsson,coh901331", U300_RTC_BASE,
 329                "rtc-coh901331", NULL),
 330        OF_DEV_AUXDATA("stericsson,coh901318", U300_DMAC_BASE,
 331                "coh901318", NULL),
 332        OF_DEV_AUXDATA("stericsson,fsmc-nand", U300_NAND_IF_PHYS_BASE,
 333                "fsmc-nand", NULL),
 334        OF_DEV_AUXDATA("arm,primecell", U300_UART0_BASE,
 335                "uart0", NULL),
 336        OF_DEV_AUXDATA("arm,primecell", U300_UART1_BASE,
 337                "uart1", NULL),
 338        OF_DEV_AUXDATA("arm,primecell", U300_SPI_BASE,
 339                "pl022", NULL),
 340        OF_DEV_AUXDATA("st,ddci2c", U300_I2C0_BASE,
 341                "stu300.0", NULL),
 342        OF_DEV_AUXDATA("st,ddci2c", U300_I2C1_BASE,
 343                "stu300.1", NULL),
 344        OF_DEV_AUXDATA("arm,primecell", U300_MMCSD_BASE,
 345                "mmci", NULL),
 346        { /* sentinel */ },
 347};
 348
 349static void __init u300_init_irq_dt(void)
 350{
 351        struct device_node *syscon;
 352        struct clk *clk;
 353
 354        syscon = of_find_node_by_path("/syscon@c0011000");
 355        if (!syscon) {
 356                pr_crit("could not find syscon node\n");
 357                return;
 358        }
 359        syscon_base = of_iomap(syscon, 0);
 360        if (!syscon_base) {
 361                pr_crit("could not remap syscon\n");
 362                return;
 363        }
 364        /* initialize clocking early, we want to clock the INTCON */
 365        u300_clk_init(syscon_base);
 366
 367        /* Bootstrap EMIF and SEMI clocks */
 368        clk = clk_get_sys("pl172", NULL);
 369        BUG_ON(IS_ERR(clk));
 370        clk_prepare_enable(clk);
 371        clk = clk_get_sys("semi", NULL);
 372        BUG_ON(IS_ERR(clk));
 373        clk_prepare_enable(clk);
 374
 375        /* Clock the interrupt controller */
 376        clk = clk_get_sys("intcon", NULL);
 377        BUG_ON(IS_ERR(clk));
 378        clk_prepare_enable(clk);
 379
 380        irqchip_init();
 381}
 382
 383static void __init u300_init_machine_dt(void)
 384{
 385        u16 val;
 386
 387        /* Check what platform we run and print some status information */
 388        u300_init_check_chip();
 389
 390        /* Initialize pinmuxing */
 391        pinctrl_register_mappings(u300_pinmux_map,
 392                                  ARRAY_SIZE(u300_pinmux_map));
 393
 394        of_platform_default_populate(NULL, u300_auxdata_lookup, NULL);
 395
 396        /* Enable SEMI self refresh */
 397        val = readw(syscon_base + U300_SYSCON_SMCR) |
 398                U300_SYSCON_SMCR_SEMI_SREFREQ_ENABLE;
 399        writew(val, syscon_base + U300_SYSCON_SMCR);
 400}
 401
 402static const char * u300_board_compat[] = {
 403        "stericsson,u300",
 404        NULL,
 405};
 406
 407DT_MACHINE_START(U300_DT, "U300 S335/B335 (Device Tree)")
 408        .map_io         = u300_map_io,
 409        .init_irq       = u300_init_irq_dt,
 410        .init_time      = timer_probe,
 411        .init_machine   = u300_init_machine_dt,
 412        .restart        = u300_restart,
 413        .dt_compat      = u300_board_compat,
 414MACHINE_END
 415